Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIND PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Pressure Distribution on a Slotted R.A.F. 31 Airfoil in the Variable Density Wind Tunnel

Measurements were made in the variable density wind tunnel to determine the pressure distribution over one section of a R.A.F. 31 airfoil with a leading edge slot fully open. To provide data for the study of scale effect on this type of airfoil, the tests were conducted with air densities of approximately one and twenty atmospheres.

Jacobs, Eastman N↗

The 630 nm MIG and the vertical neutral wind in the low latitude nighttime thermosphere

It is shown that large negative divergences (gradients) in the horizontal neutral wind in the equatorial thermosphere can support downward neutral winds in excess of 20 m/s. With attention to the meridional and vertical winds only, the pressure tendency equation is used to derive the expression U(sub z0) approximately equals (Partial derivative U(sub y)/Partial derivative y)H for the vertical wind U(sub z0) at the reference altitude for the pressure tendency equation; H is the atmospheric density scale height, and (Partial derivative U(sub y)/Partial derivative y) is the meridional wind gradient. The velocity gradient associated with the Meridional Intensity Gradient (MIG) of the O((sup 1)D) emission (630 nm) at low latitudes is used to estimate the vertical neutral wind in the MIG region. Velocity gradients derived from MIG data are about 0.5 (m/s)/km) or more, indicating that the MIG region may contain downward neutral winds in excess of 20 m/s. Though direct measurements of the vertical wind are scarce, Fabry-Perot interferometer data of the equatorial F-region above Natal, Brazil, showed downward winds of 30 m/s occurring during a strong meridional wind convergence in 1982. In-situ measurements with the WATS instrument on the DE-2 satellite also show large vertical neutral winds in the equatorial region.

Herrero, F. A.↗

Comparison of concurrent strain gage- and pressure transducer-measured flight loads on a lifting reentry vehicle and correlation with wind tunnel predictions

Concurrent strain gage and pressure transducer measured flight loads on a lifting reentry vehicle are compared and correlated with wind tunnel-predicted loads. Subsonic, transonic, and supersonic aerodynamic loads are presented for the left fin and control surfaces of the X-24B lifting reentry vehicle. Typical left fin pressure distributions are shown. The effects of variations in angle of attack, angle of sideslip, and Mach number on the left fin loads and rudder hinge moments are presented in coefficient form. Also presented are the effects of variations in angle of attack and Mach number on the upper flap, lower flap, and aileron hinge-moment coefficients. The effects of variations in lower flap hinge moments due to changes in lower flap deflection and Mach number are presented in terms of coefficient slopes.

Tang, M. H.↗

Recommendations on setup in simulating atmospheric gravity waves under conventionally neutral boundary layer conditions

Wind farm-induced atmospheric gravity waves have been the subject of recent research as they can impact wind farm performance. Pressure variations associated with gravity waves can contribute to the global blockage effect and wind farm wake recovery. Therefore, accurate numerical simulation of flow fields, where wind-farm-induced gravity waves may be produced, is important. Three main considerations in such simulations are the overall domain size, the use of Rayleigh damping near domain boundaries to dampen gravity waves, and advection damping at the inlet to prevent spurious oscillations. Often these considerations are treated ad hoc rather than systematically. This work aims to test and extend the systematic modelling of internal gravity waves proposed in a preliminary investigation to modelling of both internal and trapped gravity waves. The preliminary study identifies the length scales to set the domain and damping layer sizes and the time scale to configure the Rayleigh damping coefficient but under linearly stratified conditions. Large eddy simulations of flow through a wind farm canopy are performed under conventionally neutral boundary layer (CNBL) conditions to test the validity of proposed setups for CNBL conditions. Background atmospheric parameters, such as Froude number (Fr), inversion height (H i ), and inversion layer Froude number (Fr i ) control most of the atmospheric gravity wave characteristics. We validated for CBNL conditions that the effective wavelengths of the internal gravity waves are the correct length scale to configure the domain size and damping layer thickness. Likewise, the optimum damping coefficient to dampen the internal gravity waves relates to the free atmosphere's buoyancy frequency or buoyant perturbations' time scale. We infer that the damping coefficient in the inversion layer may relate to the inversion buoyancy frequency to effectively dampen the trapped gravity waves. Moreover, the advection damping length is linked to the horizontal wavelength of the trapped gravity waves in the inversion layer to prevent spurious waves at the inlet by retaining wave energy accumulation.

17 WIND ENERGY↗

Efficiently resolving the terrestrial-aquatic interface in E3SM with sub-grid methods to improve coastal simulations (Final Technical Report)

The broad goal of this project was to extend the capabilities of MPAS‐Ocean, the ocean component of DOE’s Energy Exascale Earth System Model (E3SM), to better resolve the hydrodynamics of the terrestrial‐aquatic interface without significantly increasing computing resource requirements. Specifically, our goal was to better resolve the small-scale features across the terrestrial‐aquatic interface which includes the low lying coastal floodplain and a dendritic network of hydraulically efficient channels connected to estuarine systems and back bays, barrier islands and high energy inlets. The processes driving flow across the terrestrial‐aquatic interface include upland and floodplain hydrology, tides, wind and atmospheric pressure (including coastally generated storm surge across continental shelves and within estuaries and bays), wind waves and water temperature and salinity gradients.

58 GEOSCIENCES↗

An Integrated Fuselage-Sting Balance for a Sonic-Boom Wind-Tunnel Model

Measured and predicted pressure signatures from a lifting wind-tunnel model can be compared when the lift on the model is accurately known. The model's lift can be set by bending the support sting to a desired angle of attack. This method is simple in practice, but difficult to accurately apply. A second method is to build a normal force/pitching moment balance into the aft end of the sting, and use an angle-of-attack mechanism to set model attitude. In this report, a method for designing a sting/balance into the aft fuselage/sting of a sonic-boom model is described. A computer code is given, and a sample sting design is outlined to demonstrate the method.

Mack, Robert J.↗

Agrivoltaic Racking Design Optimization Based on Wind and Snow Loading Finite Element Analysis

The racking structure of photovoltaic (PV) systems plays a critical role in ensuring the PV panels generate power properly as it provides integral structural support and sometimes even solar tracking ability. Distinct applications of PV systems require variations of racking structure designs, which yield different mechanical performances under external loading conditions from the environment, such as heavy wind and snow. Past works, such as Reddy et al. [1], have analyzed the pressure effects of wind and snow loading on the racking structure of conventional rooftop and utility PV systems, but there is little knowledge of how various agrivoltaic racking systems perform, in terms of stress and strain, under the same loading conditions. There is also a knowledge gap in the industry on a set of optimized agrivoltaic racking design standards. This study investigates the mechanical performance of various existing racking systems and proposes novel designs that are optimized for agrivoltaics applications under wind and snow loading.

Liao, Quanhuan↗

Evaluation of Grid Modification Methods for On- and Off-Track Sonic Boom Analysis

Grid modification methods have been under development at NASA to enable better predictions of low boom pressure signatures from supersonic aircraft. As part of this effort, two new codes, Stretched and Sheared Grid - Modified (SSG) and Boom Grid (BG), have been developed in the past year. The CFD results from these codes have been compared with ones from the earlier grid modification codes Stretched and Sheared Grid (SSGRID) and Mach Cone Aligned Prism (MCAP) and also with the available experimental results. NASA's unstructured grid suite of software TetrUSS and the automatic sourcing code AUTOSRC were used for base grid generation and flow solutions. The BG method has been evaluated on three wind tunnel models. Pressure signatures have been obtained up to two body lengths below a Gulfstream aircraft wind tunnel model. Good agreement with the wind tunnel results have been obtained for both on-track and off-track (up to 53 degrees) cases. On-track pressure signatures up to ten body lengths below a Straight Line Segmented Leading Edge (SLSLE) wind tunnel model have been extracted. Good agreement with the wind tunnel results have been obtained. Pressure signatures have been obtained at 1.5 body lengths below a Lockheed Martin aircraft wind tunnel model. Good agreement with the wind tunnel results have been obtained for both on-track and off-track (up to 40 degrees) cases. Grid sensitivity studies have been carried out to investigate any grid size related issues. Methods have been evaluated for fully turbulent, mixed laminar/turbulent and fully laminar flow conditions.

Nayani, Sudheer N.↗

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper describes the Dynamic Mode Decomposition (DMD) of the pressures on the scale model of the Space Launch System (SLS) Block 1 cargo vehicle with the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected in the Ascent Transient Aerodynamics Tests with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD) of the data matrix. For the matrix of the uPSP measurements of the SLS ATAT, the number of rows is equal to the number of nodes in the grid of the scale model, and the number of columns is equal to the number of frames in the videos taken with 4 Phantom high-speed cameras. In this paper, it is verified that, for the time series with zero mean value, the DMD is equivalent to the decomposition with the Discrete Fourier Transform (DFT). Considering the uPSP is mainly used in the assessment of the unsteady, aerodynamic phenomena, the DMD of the uPSP measurements can be implemented in two steps: (1) subtract the mean value from the uPSP measurement on each of the grid nodes; (2) apply the Fast Fourier Transform (FFT) on the resulting zero-mean time series. The DMD of the uPSP measurements with FFT has two advantages: (1) the computational complexity of FFT is O(N*logN), where N is the length of the time series; (2) compared to the SVD-based DMD algorithm, the DMD with FFT can be easily implemented in parallel processing. A sample matrix of uPSP measurements, at the size of 341 grid nodes and 128 frames, is generated. Figures 1 and 2 show the eigenvalues and the ratios of the eigenvectors, respectively, of the sample matrix, without and with the mean value removed on each of the grid nodes, computed with the SVD-based DMD and the FFT. The figures demonstrate the equivalence of the SVD-based DMD and the decomposition with DFT/FFT for the time series with zero mean value. The results of DMD of the uPSP measurements of the SLS ATAT in September 2019 are presented in the paper. The DMD modes at different frequencies are shown, the aerodynamic phenomena (e.g. shockwave and vortex shedding) are demonstrated and the correlation of the DMD modes with the test configuration parameter (e.g., the Mach Number) is discussed. Figure 3 shows a software tool to visualize the DMD modes. The code to implement the algorithm described in this paper was written in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, and executed on the NASA Pleiades supercomputer. Funding for this research was provided by the NASA Aerosciences Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗

Seismic Noise Induced by Wind Turbine Operation and Wind Gusts

Improved seismic noise characterization, due to varied sources, may benefit traditional applications. Some examples are earthquake detection, Earth structure research, and nuclear testing. This improvement could also permit use of seismic data in transdisciplinary research such as wind gust detection and wind turbine (WT) condition monitoring. However, it is a challenging task to unambiguously quantify relationships between potential sources of seismic noise and the actual seismic response. In this article, we analyze seismic and meteorological data (wind speed and pressure), measured at a remote site in a complex terrain area in eastern Portugal, to examine seismic signatures from WT operational status and wind gusts. Results presented herein show the following: (1) WT signatures in seismic data can be used to accurately determine WT-operational status. Attenuation of WT signatures in seismic data exhibits an exponential decay with distance, with attenuation coefficients that scale with frequency. (2) After WT signatures are removed from seismic power spectra, wind gust signatures remain. Analyses of these data further indicate that it may be possible to extract quantitative wind gust estimates from seismic data and decompose them into pressure and shear stress drivers of this coupling.

Geochemistry & Geophysics↗

High pressure Mach 10 to 20 electrothermal hypersonic wind tunnel

A new technique is described for generating high enthalpy, long pulse flows for testing scramjet combustors at equivalent flight Mach numbers of 10 to 20. The approach derives from high pressure discharge technology developed for electrothermal guns and space thrusters. Cryogenic liquid air is heated with a high power electric discharge (500 MW for a 15 kg/sec test flow rate) in a capillary tube, generating a quasi-steady pressure of up to 6800 atm at 20,000 K. The heated air is mixed with additional cryogenic air and is expanded in a conventional supersonic nozzle to 0.5 to 1 atm at 3000 to 6000 m/sec. Combustion and nozzle expansion test time of approximately 300 m/sec are contemplated. Facility nozzle chemical kinetics calculations show that above Mach 16 increasing concentrations of argon and oxygen replenishment are required to obtain suitable test conditions. Initial experiments on a subscale test rig are described for 0.5 kg/sec and 300 atm pressure.

Burton, R. L.↗

The NASA/MSFC global reference atmospheric model: MOD 3 (with spherical harmonic wind model)

Improvements to the global reference atmospheric model are described. The basic model includes monthly mean values of pressure, density, temperature, and geostrophic winds, as well as quasi-biennial and small and large scale random perturbations. A spherical harmonic wind model for the 25 to 90 km height range is included. Below 25 km and above 90 km, the GRAM program uses the geostrophic wind equations and pressure data to compute the mean wind. In the altitudes where the geostrophic wind relations are used, an interpolation scheme is employed for estimating winds at low latitudes where the geostrophic wind relations being to mesh down. Several sample wind profiles are given, as computed by the spherical harmonic model. User and programmer manuals are presented.

Justus, C. G.↗

Global view of the upper level outflow patterns associated with tropical cyclone intensity changes during FGGE

The characteristics of the upper tropospheric outflow patterns which occur with tropical cyclone intensification and weakening over all of the global tropical cyclone basins during the year long period of the First GARP Global Experiment (FGGE) are discussed. By intensification is meant the change in the tropical cyclone's maximum wind or central pressure, not the change of the cyclone's outer 1 to 3 deg radius mean wind which we classify as cyclone strength. All the 80 tropical cyclones which existed during the FGGE year are studied. Two-hundred mb wind fields are derived from the analysis of the European Center for Medium Range Weather Forecasting (ECMWF) which makes extensive use of upper tropospheric satellite and aircraft winds. Corresponding satellite cloud pictures from the polar orbiting U.S. Defense Meteorological Satellite Program (DMSP) and other supplementary polar and geostationary satellite data are also used.

Chen, L.↗

Effects of dust accumulation and removal on radiators surfaces on Mars

Tests were carried out to assess the impact of wind blown dust accumulation and abrasion on radiator surfaces on Mars. High emittance arc-textured copper and niobium-1 percent-zirconium samples were subjected to basaltic dust laden wind at Martian pressure (1000 Pa) at speeds varying from 19 to 97 m/s in the Martian Surface Wind Tunnel. The effect of accumulated dust was also observed by pre-dusting some of the samples before the test. Radiator degradation was determined by measuring the change in the emittance after dust was deposited and/or removed. The principle mode of degradation was abrasion. Arc textured Nb-1 percent-Zr proved to be more susceptible to degradation than Cu, and pre-dusting appeared to have lessened the abrasion.

Gaier, James R.↗

Effects of dust accumulation and removal on radiator surfaces on Mars

Tests were carried out to assess the impact of wind blown dust accumulation and abrasion on radiator surfaces on Mars. High emittance arc-textured copper and niobium-1 percent-zirconium samples were subjected to basaltic dust laden wind at Martian pressure (1000 Pa) at speeds varying from 19 to 97 m/s in the Martian Surface Wind Tunnel. The effect of accumulated dust was also observed by pre-dusting some of the samples before the test. Radiator degradation was determined by measuring the change in the emittance after dust was deposited and/or removed. The principle mode of degradation was abrasion. Arc textured Nb-1 percent-Zr proved to be more susceptible to degradation than Cu, and pre-dusting appeared to have lessened the abrasion.

Gaier, James R.↗

Evanescent pressure gradient response in the upper ocean to subinertial wind stress forcing of finite wavelength

A schematic model is used to interpret field observations related to the mixed layer response to wind stress at subinertial frequencies. It is shown that subinertial density and pressure fluctuations can arise locally from the finite wavelength character of the wind stress forcing as a fundamental part of the upper ocean transient, wind-driven response on time scales of 2-10 pendulum days. Evanescent vertical motions arise which alter the density field of the pycnocline, and hence the pressure field over the entire upper ocean. It is thus found that in the real ocean driven by wind stress, a transient geostrophic response exists which can be as large or larger than the transient Eckman response.

White, Warren B.↗

Euro-Atlantic winter storminess and precipitation extremes under 1.5 °C vs. 2 °C warming scenarios

Severe winter storms in combination with precipitation extremes pose a serious threat to Europe. Located at the southeastern exit of the North Atlantic's storm track, European coastlines are directly exposed to impacts by high wind speeds, storm floods and coastal erosion. In this study we analyze potential changes in simulated winter storminess and extreme precipitation, which may occur under 1.5 or 2°C warming scenarios. Here we focus on a first simulation suite of the atmospheric model CAM5 performed within the HAPPI project and evaluate how changes of the horizontal model resolution impact the results regarding atmospheric pressure, storm tracks, wind speed and precipitation extremes. The comparison of CAM5 simulations with different resolutions indicates that an increased horizontal resolution to 0.25° not only refines regional-scale information but also improves large-scale atmospheric circulation features over the Euro-Atlantic region. The zonal bias in monthly pressure at mean sea level and wind fields, which is typically found in low-resolution models, is considerably reduced. This allows us to analyze potential changes in regional- to local-scale extreme wind speeds and precipitation in a more realistic way. Our analysis of the future response for the 2°C warming scenario generally confirms previous model simulations suggesting a poleward shift and intensification of the meridional circulation in the Euro-Atlantic region. Additional analysis suggests that this shift occurs mainly after exceeding the 1.5°C global warming level, when the midlatitude jet stream manifests a strengthening northeastward. At the same time, this northeastern shift of the storm tracks allows an intensification and northeastern expansion of the Azores high, leading to a tendency of less precipitation across the Bay of Biscay and North Sea. Here, regions impacted by the strengthening of the midlatitude jet, such as the northwestern coasts of the British Isles, Scandinavia and the Norwegian Sea, and over the North Atlantic east of Newfoundland, experience an increase in the mean as well as daily and sub-daily precipitation, wind extremes and storminess, suggesting an important influence of increasing storm activity in these regions in response to global warming.

54 ENVIRONMENTAL SCIENCES↗

Comparison of wind tunnel and flight test afterbody and nozzle pressures for a twin-jet fighter aircraft at transonic speeds

Afterbody and nozzle pressures measured on a 1/12-scale model and in flight on a twin-jet fighter aircraft were compared as Mach number varied from 0.6 to 1.2, Reynolds number from 17.5 million to 302.5 million, and angle of attack from 1 to 7 deg. At Mach 0.6 and 0.8, nozzle pressure coefficient distributions and nozzle axial force coefficients agreed and showed good recompression. At Mach 0.9 and 1.2, flow complexity caused a loss in recompression for both flight and wind tunnel nozzle data. The flight data exhibited less negative values of pressure coefficient and lower axial force coefficients than did the wind tunnel data. Reynolds number effects were noted only at these Mach numbers. Jet temperature and mass flux ratio did not affect the comparisons of nozzle axial flow coefficient. At subsonic speeds, the levels of pressure coefficient distributions on the upper fuselage and lower nacelle surfaces for flight were less negative than those for the model. The model boundary layer thickness at the aft rake station exceeded that for the forward rake station and increased with increasing angle of attack. The flight boundary layer thickness at the aft rake station was less than that for the forward rake station and decreased with increasing angle of attack.

Nugent, Jack↗