Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Adaptive Control Law for PID

This paper is the final report for my Spring 2019 internship at the Kennedy Space Center in Cape Canaveral, Florida. The official title of my internship is 'Launch Vehicle Control Study internship,' and I spent the spring working in GMRO- Granular Mechanics and Regolith Operations. There are two components to my project involving developing an adaptive control law for a PID controller. The first component involves performing a deep study and analysis of adaptive control laws, with the goal of developing stability proofs about the control law and the gain and phase margins. The second component involves analyzing the data received after implementing the adaptive control law. Unfortunately, as of the time of writing this paper, the data is not considered ‘clean' enough to analyze. Therefore, in this paper I will give an overview of adaptive control law stability proofs and will write about the data analysis separately. Section II includes several general definitions, and the later sections have additional definitions at the end of each section.A PID (proportional integral derivative) controller is a common control algorithm which isimplemented in NASA’s rocket launch system. The idea behind the PID controller is to calculatethe error (current position – desired position) and drive it to zero by using proportional, integral,and derivative influences on the controller. For example, when a sailor steers a ship which isheading towards location 𝑥 but would like to turn the ship to reach location 𝑥∗, he/she wouldinitially turn the wheel significantly, and as the ship proceeds towards 𝑥∗ the sailor would slowlyshift the wheel back to its original position, and thereby drive the error, 𝑥∗ − 𝑥, to zero.

Eisenberg, Yael↗

Planetary Rover Simulation for Lunar Exploration Missions

When planning planetary rover missions it is useful to develop intuition and skills driving in, quite literally, alien environments before incurring the cost of reaching said locales. Simulators make it possible to operate in environments that have the physical characteristics of target locations without the expense and overhead of extensive physical tests. To that end, NASA Ames and Open Robotics collaborated on a Lunar rover driving simulator based on the open source Gazebo simulation platform and leveraging ROS (Robotic Operating System) components. The simulator was integrated with research and mission software for rover driving, system monitoring, and science instrument simulation to constitute an end-to-end Lunar mission simulation capability. Although we expect our simulator to be applicable to arbitrary Lunar regions, we designed to a reference mission of prospecting in polar regions. The harsh lighting and low illumination angles at the Lunar poles combine with the unique reflectance properties of Lunar regolith to present a challenging visual environment for both human and computer perception. Our simulator placed an emphasis on high fidelity visual simulation in order to produce synthetic imagery suitable for evaluating human rover drivers with navigation tasks, as well as providing test data for computer vision software development.In this paper, we describe the software used to construct the simulated Lunar environment and the components of the driving simulation. Our synthetic terrain generation software artificially increases the resolution of Lunar digital elevation maps by fractal synthesis and inserts craters and rocks based on Lunar size-frequency distribution models. We describe the necessary enhancements to import large scale, high resolution terrains into Gazebo, as well as our approach to modeling the visual environment of the Lunar surface. An overview of the mission software system is provided, along with how ROS was used to emulate flight software components that had not been developed yet. Finally, we discuss the effect of using the high-fidelity synthetic Lunar images for visual odometry. We also characterize the wheel slip model, and find some inconsistencies in the produced wheel slip behaviour.

Allan, Mark↗

Ion Thruster Produced Roll Torque

Disturbances to the ion engine’s thrust vector will cause a spacecraft to spin about its axis if left unmanaged. Spin about the yaw and pitch axis can be easily handled by a gimbal with enough authority. Spin about the roll axis however must be handled by additional thrusters or reaction wheels. In order to capitalize on the high efficiency of their thrusters, missions utilizing electric propulsion as primary propulsion generally include long periods of thrusting (several years). It is necessary to quantify and understand the ion thruster produced roll torque because it will define the amount of chemical propellant that must be carried or the lifetime and quantity of momentum wheels required for the mission. The roll torque produced by the NEXT ion thruster is analyzed through a combination of theoretical calculations and magnetic field simulations. Experimental techniques for measuring roll torque and past flight data are also discussed.

Arthur, Neil A.↗

Ion Thruster Produced Roll Torque

Disturbances to the ion engine's thrust vector will cause a spacecraft to spin about its axis if left unmanaged. Spin about the yaw and pitch axis can be easily handled by a gimbal with enough authority. Spin about the roll axis however must be handled by additional thrusters or reaction wheels. In order to capitalize on the high efficiency of their thrusters, missions utilizing electric propulsion as primary propulsion generally include long periods of thrusting (several years). It is necessary to quantify and understand the ion thruster produced roll torque because it will define the amount of chemical propellant that must be carried or the lifetime and quantity of momentum wheels required for the mission. The roll torque produced by the NEXT ion thruster is analyzed through a combination of theoretical calculations and magnetic field simulations. Experimental techniques for measuring roll torque and past flight data are also discussed.

Arthur, Neil A.↗

Magnetic Levitation for Long-Life Space Mechanisms: Technology Assessment and Remaining Challenges

Spacecraft mechanisms and mechanical systems must operate reliably and without failure to enable successful, long-term space missions. Such requirements place demands upon the tribological elements, especially bearings, which are frequently difficult or impossible to satisfy. Several recent, high-profile bearing failures in coolant fluid pumps and attitude control system (ACS) momentum wheels provided the impetus to assess the state-of-the-art non-contacting magnetic levitation-based, rotor support technologies.Magnetic levitation technology continues to gain acceptance for terrestrial applications and has been spaceflight demonstrated in mechanical systems such as reaction wheels (RWs) but is not in widespread use. The specific reasons inhibiting this new technology are not readily clear but include cost, weight, performance, and perceived risk. These reasons arise from a variety of real and perceived technical limitations in areas like materials, controls, sensors, thermal management and others. This white paper seeks to determine, define, and quantify the technical hurdles and gaps that must be overcome to enable the broad adoption of non-contacting bearings for long-life space mechanisms. It is anticipated that a better understanding of this complex topic may guide resource investments and clear the path to improved performance mechanical systems for spacecraft.

Samuel A Howard↗

Development of Pericyclic Gearbox for Roving Application

Many aerospace mechanisms require high gear reduction ratios to reduce the high output speed of a motor to much lower speeds for precision rotation. Conventionally this actuation is performed with multiple gear stages, typically including a harmonic gearbox, and is required to be lightweight for spaceflight. One application of multiple gear stages is in rover wheel actuators intended for use on the Moon and Mars. These actuators require low total mass, high reliability, and precision actuation due to their remote operation. The pericyclic gearbox has the capability in a single stage to provide high reduction ratios equivalent to multiple conventional stages. Some benefits of utilizing pericyclic gear technology over multiple conventional stages are a compact form, fewer total parts, no reliance on flexible members (such as in harmonic drives), and lower total system mass. The goal of this work was to modify and build on existing modeling tools to determine the feasibility of utilizing the pericyclic gearbox for such an application. Critical aspects to consider were gear tooth loads, gear mesh efficiency, bearing loads, bearing efficiency, and total system mass. Developed tools were then used to examine a single stage pericyclic gearbox's trends in mass and efficiency for a Mars 2020 rover wheel actuator mechanism design case which was then compared to multistage gearbox designs.

Krantz, Timothy↗

Ion Thruster Produced Roll Torque

Disturbances to the ion engine’s thrust vector will cause a spacecraft to spin about its axis if left unmanaged. Spin about the yaw and pitch axes can be easily handled by a gimbal with enough authority. Spin about the roll axis, however, must be handled by additional thrusters or reaction wheels. In order to capitalize on the high efficiency of their thrusters, missions utilizing electric propulsion as primary propulsion generally include long periods of thrusting (several years). It is necessary to quantify and understand the ion thruster produced roll torque because it will define the amount of chemical propellant that must be carried or the lifetime and quantity of momentum wheels required for the mission. The roll torque produced by the NASA’s Evolutionary Xenon Thruster (NEXT) ion thruster is analyzed through a combination of theoretical calculations and magnetic field simulations. Experimental techniques for measuring roll torque and past flight data are also discussed.

Neil A Arthur↗

Path following using visual odometry for Mars Rover in high-slip environments.

An architecture for autonomous operation of Mars rovers in high slip environments has been designed, implemented, and tested. This architecture is composed of several key technologies that enable the rover to accurately follow a designated path, compensate for slippage, and reach intended goals independent of the terrain over which it is traversing (within the mechanical constraints of the mobility system). These technologies include: visual odometry, full vehicle kinematics, a Kalman filter, and a slop compensation/path follower. Visual odometry tracks distinctive scene features in stereo imagery to estimate rover motion between successively acquired stereo image pairs using a maximum likelihood motion estimation algorithm. The full vehicle kinematics for a rocker-bogie suspension system estimates motion, with a no-slip assumption, by measuring wheel, rates, and rocker, bogie, and steering angles. The Kalman filter merges data from an Inertial Measurement Unit (IMU) and visual odometry. This merged estimate is then compared to the kinematic estimate to determining (tracking into account estimate uncertainties) if and how much slippage has occurred then a slip vector is calculated by differencing the current Kalman filter estimate from the kinematic estimate. This slip vector is then used, in conjunction with the inverse kinematics, to determine the necessary wheel velocities and steering angles to compensate for slip and follow the desired path.

Roumeliotis, Stergios I.↗

Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) Onboard Calibration System

The AVIRIS instrument uses an onboard calibration system to provide auxiliary calibration data. The system consists of tungsten halogen cycle lamp imaged onto a fiber bundle through an eight position filter wheel. The fiber bundle illuminates the back side of the foreoptics shutter during a pre-run and post-run calibration sequence. The filter wheel contains 2 neutral density filters, 5 spectral filters and blocked position.

spectrometer↗

Mission Summary of Cassini Spacecraft Guidance and Control Hardware Health and Performance

The Cassini-Huygens mission ended on September 15, 2017, after nearly two decades in ight. The well-designed Cassini spacecraft had robust hardware that permitted two extended missions, lasting nine years longer than the expected prime mission. At the end of the mission, the Attitude and Articulation Control Subsystem (AACS) was using two pieces of redundant back-up of hardware, one reaction wheel and the hydrazine thruster branch, due to hardware anomalies earlier in the mission. The back-up hardware performed nominally through the rest of mission. The prime reaction wheels at the end of the mission had reached more than 130% of the consumable limit for number of revolutions. No thruster on either thruster branch accumulated more than 45% of the consumable limits. The inertial reference unit slightly exceeded the pre-launch requirements on bias error, but as the software continuously estimated this value in ight, the attitude estimation was not adversely a ected. The star trackers performed nominally, and though there was a spacecraft anomaly in 1998 related to the star trackers, the origin was not in hardware itself. The Sun sensors and accelerometer both performed as expected and met all requirements throughout the mission. Ultimately, the lifetime of the Cassini spacecraft was not limited by hardware performance. Planetary protection requirements necessitated the end of the mission as the spacecraft's propellant reserves depleted, and Cassini plunged into Saturn's atmosphere with a healthy attitude control system.

Stupik, Joan↗

On-Orbit Performance & Operation of the Attitude & Pointing Control Subsystems on ASTERIA

The Arcsecond Space Telescope Enabling Research in Astrophysics (ASTERIA) is a 6U CubeSat that was deployed from the International Space Station on 20 November 2017. The underlying goal of the mission is to image and perform photometry on bright, nearby stars and possibly detect transiting exoplanets orbiting these stars. As a technology demonstration with an eye to enable this science, the payload must be pointed with a stability of 5 arcseconds RMS over 20-minute observations and a repeatability of 1 arcsecond RMS across multiple observations. A two-stage control system was employed to achieve these pointing requirements: reaction wheels control the attitude of the spacecraft bus while a piezo stage translates the focal plane array to control the pointing of the payload. This paper will present on-orbit results that demonstrate a pointing stability of 0.5 arcsecond RMS over 20 minutes and a pointing repeatability of 1 milliarcsecond RMS from observation to observation, the best pointing of a CubeSat to date. In addition, this paper will discuss the pointing achieved by the attitude control subsystem alone, pointing issues due to temporarily bright pixels, hot pixels, and reaction wheel speed reversals or zero crossings, the deployment and Sun acquisition phase, momentum management issues arising from a large residual dipole, and some of the anomalies encountered with the attitude control subsystem.

Pong, Christopher M.↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Instrument Development

The Electrostatic Regolith Interaction Experiment (ERIE) is a joint venture between the University of Central Florida (UCF) Center for Microgravity Research (CMR) and the NASA Kennedy Space Center (KSC) Electrostatics and Surface Physics Laboratory (ESPL) seeking to examine charged dust grain behavior in a microgravity environment. Two separate systems have been combined for this suborbital flight experiment: the COLLisions Into Dust Experiment (COLLIDE) developed by the UCF CMR and the Wheel Electrostatic Spectrometer (WES) developed by the NASA KSC ESPL. This combination will advance the understanding of the natural and induced charged grain behavior on the Moon, asteroids, and other low gravity bodies comprised of charged dust particles. COLLIDE retains granular material under vacuum in a shallow tray behind a metal door, which then opens and releases the particles into a larger open volume when microgravity is achieved. The experiment is observed with a high-speed camera, such that the motions of these particles can then be tracked so the kinematics of each grain may be analyzed. The original application for this apparatus was to study cratering events into granular beds, but electrostatic repulsion was detected in the early frames of the video data returned from completed experiments, so a re-flight with a focus on these events was proposed. Agitation of the grains during launch combined with the frictional charge transfer between the grains and the door as it slides open provides an opportunity to use this setup to observe material tribocharging and charged particle behaviors in microgravity. In this updated version, the charged particles released into the chamber will traverse through an electric field produced by high voltage parallel plates and their resulting trajectories will be determined by their net charges. WES was originally developed to characterize the triboelectric properties of the Martian regolith through the contact of a rover wheel with the surface as it rotates. Improvements were made upon this legacy system to develop a sensor suite that will be installed within the COLLIDE door to measure charge transferred between the granular material and insulating disks protruding through the door. These insulator disks span the triboelectric series so, as they slide across the particulate matter when the door opens, each will accumulate a charge consistent with its relative position to the grains within the series. This charge on each insulator is distributed between two capacitances in series with an electrometer amplifier returning an analog voltage proportional to the charge accumulated. Calibration of this system has been performed using applications of known charge to the inputs and characterization of the frictional charge transfer between various regolith simulants and the sensor insulators is currently being examined in the lab.

Electrostatics↗

Single-Cell mRNA Sequencing of Bone Marrow Mesenchymal Stem Cell Lineages Shows that Gravity Mechanical Loading Regulates Regenerative Osteogenesis in a CDKN1A-Dependent Manner

Weight-bearing at 1g is increasingly recognized as an important stimulus driving stem cell-based tissue regenerative homeostasis and health. In the bone marrow compartment, mechanical stimuli from gravity can drive osteogenesis from mesenchymal progenitors and hematopoiesis from hematopoietic progenitors. Conversely, hematopoietic monocyte/macrophage progenitors can also be driven into osteoclastogenesis by mechanical unloading in microgravity. Although the cell cycle inhibitor gene Cdkn1a is known to be upregulated in microgravity, the great diversity of stem cell lineages and stages of differentiation in bone marrow, make it difficult to attribute gene expression changes to specific cell types. To overcome this limitation, we used single-cell mRNAseq analyses with both in-vitro and in-vivo strategies, including in-vitro stretch of marrow osteogenic cultures, and in-vivo hindlimb unloading, running wheels, treadmills, and exposure to real microgravity. For in-vitro studies marrow osteoprogenitors from WT and Cdkn1a-null mice were subjected to substrate stretch during osteogenesis, with static cultures simulating unloading. From those experiments we determined Cdkn1a-null cells transition more readily from progenitors to early osteoblasts and further to mineralizing osteoblasts. Additionally, single-cell mRNAseq resolution identified Cdkn1a suppression in response to mechanical loading predominantly in early proliferative osteoblasts rather than progenitor or mineralizing osteoblasts. These findings support the hypothesis that CDKN1A plays a mechano-reversible, anti-proliferative role during bone regenerative osteogenesis. To investigate in-vivo mechanoregulation of osteogenesis, mice were flown in microgravity during the Rodent Research-10 experiment comparing wildtype and Cdkn1a-null mice kept on ISS for 30 days. The mice were euthanized and dissected on-orbit in microgravity and femur bone marrow was collected using a custom sample isolation and live-cell cryo-preservation technique allowing for single cell transcriptomics post-flight processing. Ground control experiments with hindlimb-unloading, running wheels, and treadmills, were also conducted for a comprehensive analysis of mechanical loading effects on the regenerative health of bone tissue and its marrow stem cell progenitor lineages.

single cell sequencing↗

Meteorite Sample Section Repair at NASA Johnson Space Center

Introduction: Meteorite thin and thick sections are routinely shipped from NASA Johnson Space Center to fulfill sample allocation requests from principle investigators around the world. Sections are also re-turned to JSC when researchers are finished studying them since, in most cases, they can be reused for other studies. The sections are very fragile unfortunately, and sometimes return to us needing repairs. The fol-lowing should give you an idea of how we repair sections here in the very lab where they were created. NOTE: Please do not attempt to repair ANSMET meteorite sections that are in your possession. We will perform the repairs for you at NASA JSC if you send the section back to us. Section Delamination: The majority of the meteorite sections that we produce here are secured to the glass slide using a high quality, two-part epoxy. Occasionally, we are asked to use superglue if the researcher wishes to dismount the section from the slide. Both epoxy and superglue are excellent adhesives, but they both tend to embrittle with time which results in delamination from the slide. Exposure to vacuum can also degrade the adhesion between the sample section and the glass slide. Repeated handling of the slide edges can accelerate delamination and, as a preventive measure, the outer 1-2 mm of epoxy is trimmed from newly created sections at JSC. If conductive tapes (copper, carbon, etc.) are used on the section during analysis, great care must be taken in removing the tape so that the epoxy is not pulled up with it. If in doubt, the tape can be left on the section when it is returned to JSC. Before we perform any repairs to sample sections, carbon, gold, or other coatings are removed. We accomplish this using a slurry of 0.05 micron alumina and 190 proof ethyl alcohol applied to a felt polishing pad fitted to a rotating lap wheel. Coatings are re-moved in this manner from all sections that are re-turned to JSC. The extent of the delamination determines how we proceed with the section repair. If the meteorite sample area of the section is not disturbed, then we carefully remove the delaminated epoxy. This is done using a binocular microscope with a 6X zoom, cut-proof gloves, and a very sharp, single edged razor blade. We cut the delaminated epoxy with the blade angled away from the sample area and using very light pressure. The trimmed section is then cleaned in an ultrasonic bath of 200 proof ethyl alcohol for no more than 10 seconds and carefully dried using a lint-free clean room wipe. The section is then placed into a lab oven at 110o F in preparation for epoxy. We mix the resin and hardener components of the low viscosity epoxy and very small amounts are applied to the cut edges of the section using a needle probe and the binocular microscope. Warming the epoxy helps secure the existing section by filling any voids between the glass slide and the section. After the new epoxy cures, we give the section a light polish on a lap wheel fitted with cotton polishing paper that is charged with 1 micron diamond paste. If the section has delaminated to the point of sample area being lifted from the glass, then it may be irreparable. We employ the above technique along with clamping the section in a Teflon pad arrangement in order to flatten the sample while the epoxy cures. Otherwise, the sample will tend to curl. This works to some degree, but once the sample area curls, it seldom re-turns to the original flatness without cracking or bending. Canada Balsam and Crystalbond: We repair damaged sections that had originally been prepared using Canada Balsam or Crystalbond adhesives through the gradual application of heat. We take great care with these samples since these bonding materials tend to get brittle with age. The section is heated in gradual steps (40-50o F per hour) to the melting point of the adhesive. We repair the sample while the adhesive is fluid and then the section is cooled in the same gradual manner in which it was heated. Slide Cracks and Breaks: Accidents happen. Especially with something as small and fragile as a thin/thick section. We all know someone who has driven a microscope objective into a section. As bad as the damage may look, the section can be repaired in most instances. NOTE: Please do not try to tape or glue section pieces back together prior to returning the dam-aged section. This practice usually renders the section irreparable. If the glass slide is cracked but the section is still in one piece, we repair it by infilling the crack with the low viscosity epoxy mentioned earlier. If the slide is in pieces, we can reassemble it with epoxy on a new backer slide. This is a tricky task as the pieces need to be in the correct plane with respect to each other, especially if the sample area is split among several pieces.

Meteorite↗

Euclid Near Infrared Spectro Photometer instrument concept and first test results obtained for different breadboards models at the end of phase C

The Euclid mission objective is to understand why the expansion of the Universe is accelerating through by mapping the geometry of the dark Universe by investigating the distance-redshift relationship and tracing the evolution of cosmic structures. The Euclid project is part of ESA's Cosmic Vision program with its launch planned for 2020 (ref [1]). The NISP (Near Infrared Spectrometer and Photometer) is one of the two Euclid instruments and is operating in the near-IR spectral region (900- 2000nm) as a photometer and spectrometer. The instrument is composed of: - a cold (135K) optomechanical subsystem consisting of a Silicon carbide structure, an optical assembly (corrector and camera lens), a filter wheel mechanism, a grism wheel mechanism, a calibration unit and a thermal control system - a detection subsystem based on a mosaic of 16 HAWAII2RG cooled to 95K with their front-end readout electronic cooled to 140K, integrated on a mechanical focal plane structure made with molybdenum and aluminum. The detection subsystem is mounted on the optomechanical subsystem structure - a warm electronic subsystem (280K) composed of a data processing / detector control unit and of an instrument control unit that interfaces with the spacecraft via a 1553 bus for command and control and via Spacewire links for science data This presentation describes the architecture of the instrument at the end of the phase C (Detailed Design Review), the expected performance, the technological key challenges and preliminary test results obtained for different NISP subsystem breadboards and for the NISP Structural and Thermal model (STM).

Maciaszek, Thierry↗

A Concept for the Deployment of a Large Lunar Crater Radio Telescope Using Teams of Tethered Robots

Kilometer-scale craters on the far side of the Moon have unique potential as future locations for large radio telescopes, which can observe the universe at wavelengths and frequencies (> 10 m, < 30 MHz) not possible with conventional Earth or orbital-based approaches. Distinct advantages of building a Lunar Crater Radio Telescope (LCRT) on the far side include i) isolation from radio noise due to the Earth’s ionosphere, orbiting satellites, and the Sun, ii) days of uninterrupted dark/cold sky viewing during lunar night, and iii) terrain geometry naturally suited for constructing the largest mesh antenna structure in the Solar System. A key challenge to constructing LCRT on the Moon is related to the complexity of deploying a 1-km diameter antenna and hanging receiver within a lunar crater whose diameter, depth, and slope are 3-5 km, 1 km, and ~30 degrees respectively. In this paper, we first evaluate the trade space for deploying a large, complex structure within a crater, and then provide a more detailed concept evaluation of our favored approach, which employs coordinated teams of tethered rovers to extract and suspend a folded antenna from a lander at the base of a crater. NASA’s Jet Propulsion Laboratory in collaboration with California Institute of Technology (Caltech) have developed a novel robotic system for accessing extremely steep terrains; the Axel rover is a two-wheeled rugged terrain vehicle that is supported by an electro-mechanical tether that provides power, data, and tensile support from a top-side anchor location. Recently, a pair of Axel robots have been used in a DuAxel configuration that allows for four-wheel driving and repeated passive anchoring at different locations. The DuAxel system has unique advantages for deploying an LCRT antenna, including the ability to deploy from a lander near a crater, drive a distance to the crater rim to deploy an Axel, and later, retract the deployed Axel in order to sequentially lift up sections of the antenna. Our proposed concept involves delivering a packaged antenna and receiver to the bottom-center of a crater floor on a lander, then later sending a team of multiple DuAxel rovers to retrieve guide wires from the lander, which are pulled to the top of the crater. We explore this concept in detail and provide some initial quantitative analysis to demonstrate the feasibility of our system with respect to the spatial and mass properties of the antenna as juxtaposed to DuAxel capabilities. Finally, we outline next steps towards validating our concept on the way to a future lunar deployment opportunity.

Hallinan, Greg↗

High-capacity ATHLETE Offloader Mobility Constructor Concept for Human Surface Exploration

Using cross-cabled, winch-tendon four-bar frames, a new Artemis-class ATHLETE system is a multi-limbed robotic mobility platform that is designed for surface traverse, precision placement, and offloading of heavy habitats and other large human exploration payloads from high-decked landers. Building upon lessons learned from the All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) robotic mobility system developed for Constellation Lunar Surface Systems and Evolvable Mars Campaign, a high-capacity articulated crane / lift vehicle concept has been devised that would be equipped with multi-limb six-degree-of-freedom dexterity for a variety of tasks supporting planetary surface human exploration missions and outposts. The Artemis-class ATHLETE vehicle would use any combination of three to six wheel-onlimb combinations to provide a wide “outrigger” stance to transfer loads from a high center-of-gravity on sloped terrain to low stable carry configurations for long-distance traverses, and be capable of precision docking of payloads to previously positioned elements. The new vehicle concept improves upon previous Constellation-class ATHLETE versions by allowing modular hot-swapping of individual limbs to improve maintenance and flexibility. The extreme-capacity independent limbs can individually function as single cranes, and can be delivered separately via multiple lander manifests for later congregation into self-driving “Tri-ATHLETE” vehicles after delivery to the surface. This paper provides mission architecture targets and vehicle masses for stepped payload capacity values in Earth, Mars, and Lunar gravity environments, and discusses a variety of swappable tools, including wheeled mobility attachments, grippers, excavation tools, repair fixtures, ISRU extraction, winches, block & tackle rigging combinations, 3D printheads, and construction aids.

Wilcox, Brian↗

Visual Odometry Thinking While Driving for the Curiosity Mars Rover's Three-Year Test Campaign: Impact of Evolving Constraints on Verification and Validation

Over the first 9 years of the Mars Science Laboratory (MSL) Curiosity rover's surface mission, more than 87\% of its driving has been performed using Visual Odometry (VO). The benefits of using VO during driving are that it minimizes rover position uncertainty and can be used to monitor wheel slip, halting a drive if excessive wheel slip is occurring. The VO implementation on board Curiosity acquires and processes VO images in between drive steps while the rover is stationary. A VO Thinking While Driving (VTWD) flight software capability has been developed which enables the processing of VO images during rover driving, increasing the distance Curiosity can drive with VO in a given time period up to as much as 1.75x total distance. Verification and Validation (V\&V) of the capability has been challenging due to impacts from the COVID-19 pandemic and unavailability of the JPL Mars Yard outdoor test site. The VTWD V\&V test procedures were modified to use a small indoor space with Mars-like terrain. This paper describes the 3 year V\&V effort under challenging conditions to approve the VTWD capability for use on the Curiosity rover.

Rankin, Arturo↗