Theoretical distribution of lift on thin wings at supersonic speeds : (an extension)
Explore the source record for details and available documents.
PRESSURE DISTRIBUTION - AIRFOILS, THIN↗
SEARCH · Engineering Papers
Results for “TIP SPEED”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence V - Raw Data
Sequence V: Tip Plate (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The standard tip blocks were replaced with a tip plate to simulate the effect of an undeployed tip-mounted aerodynamic brake as shown in Appendix A. Note that the blade radius was not changed during post-processing so the pressure tap locations are at the same radial location, but the reference to 30% represents 30% of 5.029 m, not 4.943 m. Throughout this report, references to the blade span are made for the 5.029- m radius, not the 4.943-m radius.
17 WIND ENERGY↗
Calculated performance map of a 4 1/2-stage 15.0 centimeter (5.9 inch) mean diameter turbine designed for a turbofan simulator
The overall performance of an existing high-ratio turbine is calculated analytically over a range of speed and pressure ratio in order to determine its capability for other applications. The analytical performance covers a speed range from 50 to 120 percent of design and a pressure-ratio range from 5.0 to 35.0. The turbine was designed for a 50.8 centimeter (20.0 in.) tip diameter turbofan simulator. Computed results are compared with the experimental turbine data obtained from testing three fan configurations with the turbofan simulator in air. The comparison indicates good agreement over the range of speeds and pressure ratios covered by the experimental data.
Wasserbauer, C. A.↗
Wind-Tunnel Tests of the 1/25-Scale Powered Model of the Martin JRM-1 Airplane. IV - Tests with Ground Board and with Modified Wing and Hull - TED No. NACA 232: Tests with Ground Board and with Modified Wing and Hull, TED No. NACA 232 - Part 4
Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.
Lockwood, Vernard E.↗
Experimental investigation of an 0.8 hub-tip radius-ratio,nontwisted-rotor-blade turbine
An experimental investigation of a 0.8 hub-tip radius ratio, nontwisted-rotor-blade turbine designed for a stagnation-pressure ratio of 2.5 and an equivalent mean blade speed of 643 feet per second was made in a cold-air turbine with (a) nontwisted stator blades, and (b) twisted stator blades designed to maintain zero rotor-inlet incidence angles. Turbine efficiencies of the order of 0.85 at the design point were obtained with a nontwisted-rotor-blade turbine with a hub-tip radius ratio of 0.80. The turbine with the twisted stator blades gave higher efficiencies at the design point (of the order of 1.5 percentage points) than the turbine with the nontwisted stator blades.
TURBINES - AXIAL FLOW↗
A comparison of several tapered wings designed to avoid tip stalling
Optimum proportions of tapered wings were investigated by a method that involved a comparison of wings designed to be aerodynamically equal. The conditions of aerodynamic equality were equality in stalling speed, in induced drag at a low speed, and in the total drag at cruising speed. After the wings were adjusted to aerodynamic equivalence, the weights of the wings were calculated as a convenient method of indicating the optimum wing. The aerodynamic characteristics were calculated from wing theory and test data for the airfoil sections. Various combinations of washout, camber increase in the airfoil sections from the center to the tips, and sharp leading edges at the center were used to bring about the desired equivalence of maximum lift and center-stalling characteristics. In the calculation of the weights of the wings, a simple type of spar structure was assumed that permitted an integration across the span to determine the web and the flange weights. The covering and the remaining weight were taken in proportion to the wing area. The total weights showed the wings with camber and washout to have the lowest weights and indicated the minimum for wings with a taper ratio between 1/2 and 1/3.
Anderson, Raymond F↗
Insights Into Lightning K‐Leader Initiation and Development From Three Dimensional Broadband Interferometric Observations
Abstract We report detailed observations of K‐leaders and the activity between them with the three‐dimensional Broadband Interferometric Mapping and Polarization system (BIMAP‐3D) at Los Alamos National Laboratory. It is found that K‐leaders have a general propagation trend of initial acceleration and then gradual deceleration, and the corresponding very high frequency (VHF) radiation power is exponentially correlated with the leader speed. Based on the 3D development and simultaneous electric field change measurement, some simple K‐leaders can be modeled with time‐evolving point charges at the propagating leader tip and at the stationary origin. We found that the charge magnitude increases during the initial acceleration stage and stays relatively constant for the rest of the development. K‐leaders are observed to interact with other branches; the branches affect the leader's propagation speed, and may affect the charge transfer. After the occurrence of a K‐leader, VHF emissions are quenched for several milliseconds. VHF sources then reappear in an impulsive and scattered manner as “twinkling,” and these sources are found not uniquely on the so‐called needles, but also on the main channel. These twinkling sources start near the apparent positive leader tip, and extend back toward the direction of the flash origin at about 10 5 m/s, while the apparent positive tip continues to extend forward at about 10 4 m/s. The twinkling extending toward the direction of flash origin appears to initiate the following K‐leader, although it may be interrupted by a K‐leader along a different branch, or simply die out without more K‐leader activity.
54 ENVIRONMENTAL SCIENCES↗
Effect of casing treatment on performance of a two-stage high-pressure-ratio fan
A two-stage fan, previously tested with a solid casing, was tested with a casing with circumferential grooves over the tips of both rotors (casing treatment). Tests were conducted at 80 and 100 percent of design speed with uniform flow. The casing treatment improved the flow range and stall margin significantly without changing the characteristics overall performance curves of total-pressure and efficiency as functions of weight flow, other than extending them to lower weight flows.
Urasek, D. C.↗
Numerical calculation of steady inviscid full potential compressible flow about wind turbine blades
The air flow through a propeller-type wind turbine rotor is characterized by three-dimensional rotating cascade effects about the inner portions of the rotor blades and compressibility effects about the tip regions of the blades. In the case of large rotor diameter and/or increased rotor angular speed, the existence of small supersonic zones terminated by weak shocks is possible. An exact nonlinear mathematical model (called a steady Full Potential Equation - FPE) that accounts for the above phenomena has been rederived. An artificially time dependent version of FPE was iteratively solved by a finite volume technique involving an artificial viscosity and a three-level consecutive mesh refinement. The exact boundary conditions were applied by generating a boundary conforming periodic computation mesh.
Dulikravich, D. S.↗
STOL capability impact on advanced tactical aircraft design
The design and technical issues affecting supersonic STOL development as an airbase attack fighter are discussed. An Air Force study has indicated that, from a weight and cost standpoint, the preferred directions will include two-dimensional nozzles with vectoring and thrust reversing capability. Take-off and landing requirements would determine other design features, and the use of a jump strut to enable landing maneuvers to be made at pitch angles which would normally drag the tail is detailed. The addition of a tip-mounted reaction control system is foreseen as necessary for roll control at the low aerodynamic speeds of STOL landing. A severe 700 ft landing distance design is outlined, and includes a lifting engine with bleed-air features to feed the reaction control system.
Krepski, R. E.↗
Performance of a tandem-rotor/tandem-stator conical-flow compressor designed for a pressure ratio of 3
A conical-flow compressor stage with a large radius change through the rotor was tested at three values of rotor tip clearance. The stage had a tandem rotor and a tandem stator. Peak efficiency at design speed was 0.774 at a pressure ratio of 2.613. The rotor was tested without the stator, and detailed survey data were obtained for each rotor blade row. Overall peak rotor efficiency was 0.871 at a pressure ratio of 2.952.
Wood, J. R.↗
Langley Field wind tunnel apparatus
The difficulties experienced in properly holding thin tipped or tapered airfoils while testing on an N.P.L. type aerodynamic balance even at low air speeds, and the impossibility of holding even solid metal models at the high speeds attainable at the National Advisory Committee's wind tunnel, necessitated the design of a balance which would hold model airfoils of any thickness and at speeds up to 150 m.p.h. In addition to mechanical strength and rigidity, it was highly desirable that the balance readings should require a minimum amount of correction and mathematical manipulation in order to obtain the lift and drag coefficients and the center of pressure. The balance described herein is similar to one in use at the University of Gottingen, the main difference lying in the addition of a device for reading the center of pressure directly, without the necessity of any correction whatsoever. Details of the design and operation of the device are given.
Bacon, D L↗
NPSS Multidisciplinary Integration and Analysis
The objective of this task was to enhance the capability of the Numerical Propulsion System Simulation (NPSS) by expanding its reach into the high-fidelity multidisciplinary analysis area. This task investigated numerical techniques to convert between cold static to hot running geometry of compressor blades. Numerical calculations of blade deformations were iteratively done with high fidelity flow simulations together with high fidelity structural analysis of the compressor blade. The flow simulations were performed with the Advanced Ducted Propfan Analysis (ADPAC) code, while structural analyses were performed with the ANSYS code. High fidelity analyses were used to evaluate the effects on performance of: variations in tip clearance, uncertainty in manufacturing tolerance, variable inlet guide vane scheduling, and the effects of rotational speed on the hot running geometry of the compressor blades.
Hall, Edward J.↗
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence E - Raw Data
Sequence E: Yaw Releases (P) This test sequence used a downwind, rigid turbine with a 3.4° cone angle. The wind speeds ranged from 7 m/s to 17 m/s. Initial yaw angles of ±90° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. The turbine was positioned at each specified yaw angle. A 30- second data set was collected with the yaw brake engaged. These points used a letter for the last digit beginning with A and proceeding through the alphabet as repeat points were needed. These points were plotted and compared to ascertain the functionality of the instrumentation. The files ending in numbers beginning with 0 and increasing with each repetition represent yaw release points. Once the fixed-position yaw test was complete, the yaw drive was engaged to hold the turbine. The yaw brake was released, and the yaw drive was disabled allowing the turbine to yaw freely. The yaw drive was disabled about 5 seconds into the campaign, and the turbine was allowed to yaw freely for the rest of the 30-second duration. When the yaw drive is disabled, no torque is applied to the motor, and the inertia and yawing force of the nacelle and rotor overcomes the friction and inertia of the yaw gear and motor. The yaw releases were repeated five times at each condition. Four additional campaigns were collected to determine the turbine’s natural yaw error by releasing the brake at 0° yaw error. These file names use the E designation, followed by two digits for wind speed, followed by XXXX, followed by the repetition digit.
17 WIND ENERGY↗
Optimum Design of a Compound Helicopter
A design and aeromechanics investigation was conducted for a 100,000-lb compound helicopter with a single main rotor, which is to cruise at 250 knots at 4000 ft/95 deg F condition. Performance, stability, and control analyses were conducted with the comprehensive rotorcraft analysis CAMRAD II. Wind tunnel test measurements of the performance of the H-34 and UH-1D rotors at high advance ratio were compared with calculations to assess the accuracy of the analysis for the design of a high speed helicopter. In general, good correlation was obtained when an increase of drag coefficients in the reverse flow region was implemented. An assessment of various design parameters (disk loading, blade loading, wing loading) on the performance of the compound helicopter was conducted. Lower wing loading (larger wing area) and higher blade loading (smaller blade chord) increased aircraft lift-to-drag ratio. However, disk loading has a small influence on aircraft lift-to-drag ratio. A rotor parametric study showed that most of the benefit of slowing the rotor occurred at the initial 20 to 30% reduction of the advancing blade tip Mach number. No stability issues were observed with the current design. Control derivatives did not change significantly with speed, but the did exhibit significant coupling.
Yeo, Hyeonsoo↗
Outdoor test stand performance of a convertible engine with variable inlet guide vanes for advanced rotorcraft propulsion
A variable inlet guide van (VIGV) type convertible engine that could be used to power future high-speed rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip airflow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque. Previous mission analyses of a conceptual X-wing rotorcraft capable of 400-knot cruise speed were revised to account for more fan-tip churning power loss than was originally estimated. The new calculations confirm that using convertible engines rather than separate lift and cruise engines would result in a smaller, lighter craft with lower fuel use and direct operating cost.
Mcardle, Jack G.↗
The convertible engine: A dual-mode propulsion system
A variable inlet guide vane (VIGV) convertible engine that could be used to power future high-speed rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open, fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed, fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip air flow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque. Previous mission analyses of a conceptual X-wing rotorcraft capable of 400-knot cruise speed were revised to account for more fan-tip churning power loss that was originally estimated. The calculations confirm that using convertible engines rather than separate life and cruise engines would result in a smaller, lighter craft with lower fuel use and direct operating cost.
Mcardle, Jack G.↗
The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight
This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.
WING SLOTS↗