Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Experimental performance and analysis of 15.04-centimeter-tip-diameter, radial-inflow turbine with work factor of 1.126 and thick blading

The aerodynamic design, the performance, and an internal loss breakdown were examined for a 15.04 cm tip diameter, radial-inflow turbine. The design application was to drive a two stage, 10 to 1 pressure ratio compressor with a mass flow of 0.952 kg/sec and a rotative speed of 70,000 rmp. The turbine inlet temperature was 1478 K, and the turbine was designed with blades thick enough for internal cooling passages. The rotor tip diameter was limited to 86 percent of optimum in order to obtain a reduced tip speed design. The turbine was fabricated with solid, uncooled blading and tested in air at nominal inlet pressure and temperature of 1.379 x 10000 N/sq m and 322.2 K, respectively. Results indicated the turbine total efficiency to be 5.3 points less than design. Analysis of these results has indicated the deficit in performance to be due to stator secondary flow losses, vaneless space surface friction losses, and trailing edge wake mixing losses.

Mclallin, K. L.↗
NASA NTRS1980

Effect of inflow control on inlet noise of a cut-on fan

A cut-on, high tip speed fan stage was acoustically tested with three configurations of an inflow control device in the NASA Lewis anechoic chamber. Although this was a cut-on design, rotor-inflow interaction appeared to be a much stronger source of blade passing tone radiated from the inlet than rotor-stator interaction for the 1.6 mean rotor chord separation. Aft external suction applied to the area where the inflow control device joined the inlet produced a further reduction in blade passing tone suggesting that disturbances in the forward flow on the outside of the inlet were superimposed on the inlet boundary layer and were a significant source of tone noise.

Woodward, R. P.↗
NASA NTRS1980

Experimental study of low aspect ratio compressor blading

The paper presents a study of low aspect blading for the inlet stages of a high pressure ratio, high-speed core compressor. The basic overall design variables were stage pressure ratio and blade aspect ratio; these four stages represent two levels of total pressure ratio, two levels of rotor blade aspect ratio, and two levels of stator vane aspect ratios. Comparisons of the overall performance, radial distributions of performance parameters, diffusion factors at the near-stall conditions, blade element data, and the axial distribution of rotor tip static pressures yielded the following results: (1) higher peak pressure ratio, high stage and rotor efficiencies, and greater stall margin were obtained with the lower aspect ratio blading, (2) the lower aspect ratio blading showed improved performance over the entire blade span, and (3) the lower aspect ratio rotors operated at higher diffusion factors and higher incidence angles over the entire blade span.

Reid, L.↗
NASA NTRS1980

Development of moldable, high density reaction bonded silicon nitride

It is noted that currently available reaction bonded silicon nitride (RBSN) materials are limited by relatively low strength (up to 300 MPa) and oxidation resistance, primarily due to open porosity. Attention is given to technology that was developed and used to produce an improved grade of injection molded RBSN having a density of 2.8 g/cc, with significantly decreased open porosity and a strength exceeding 350 MPa. It is shown that these results are primarily due to advances in two areas: silicon powder processing, and nitriding technique. A comparison of room temperature strength and oxidation resistance of the new material with that of state-of-the-art RBSN, showed significant improvements. It is concluded that turbine stator vanes were produced to show that this improved RBSN technology has been reduced to engineering practice.

Mangels, J. A.↗
NASA NTRS1980

Numerical calculation of transonic axial turbomachinery flows

This paper presents a numerical method and the results of a computer program for solving an exact, three-dimensional, full-potential equation that models rotating and nonrotating inviscid, absolutely irrotational, homentropic flows. Besides calculating the flows through an arbitrarily shaped rotor or stator blade row mounted on an axisymmetric hub and confined in an axisymmetric duct, the computer program is also capable of analysing flow fields about arbitrarily shaped wing-body combinations, propellers, helicopter rotors in hover, and wind turbine rotors. The governing equation is solved numerically in a fully conservative form by using an artificial time concept, a finite volume technique, rotated type-dependent differencing, successive line overrelaxation, and sequential boundary-conforming grid refinement. An artificial viscosity is added in fully conservative form; and an initial guess for the potential field is applied, as determined by a two-dimensional cascade analysis.

Dulikravich, D. S.↗
NASA NTRS1980

Minimum energy trap states of dual-spin spacecraft

The general solution to the bearing axis motor torque required to escape a minimum energy trap state is presented for oblate dual-spin spacecraft. A simplified, reduced order analysis of the bearing torque is then obtained for the case of small static imbalances, dynamic imbalances, and asymmetries on the rotor and the stator. This analysis is extended to include large asymmetry on one of the bodies. The results are applied to the design of the Galileo spacecraft.

Hollars, M. G.↗
NASA NTRS1981

Turbine modeling technique to generate off-design performance data for both single and multistage axial-flow turbines

This technique is applicable to larger axial flow turbines which may or may not incorporate variable geometry in the first stage stator. A user specified option will also permit the calculation of design point cooling flow levels and the corresponding change in turbine efficiency. The modeling technique was incorporated into a time sharing computer program in order to facilitate its use. Because this report contains a description of the input output data, values of typical inputs, and example cases, it is suitable as a user's manual.

Converse, G. L.↗
NASA NTRS1981

Reasons for low aerodynamic performance of 13.5-centimeter-tip-diameter aircraft engine starter turbine

The reasons for the low aerodynamic performance of a 13.5 cm tip diameter aircraft engine starter turbine were investigated. Both the stator and the stage were evaluated. Approximately 10 percent improvement in turbine efficiency was obtained when the honeycomb shroud over the rotor blade tips was filled to obtain a solid shroud surface. Efficiency improvements were obtained for three rotor configurations when the shroud was filled. It is suggested that the large loss associated with the open honeycomb shroud is due primarily to energy loss associated with gas transportation as a result of the blade to blade pressure differential at the tip section.

Haas, J. E.↗
NASA NTRS1981

Improved method for calculating transonic velocities on blade-to-blade stream surfaces of a turbomachine

A method was developed to improve the accuracy of an existing computer program used to calculate transonic velocities on a blade-to-blade surface of a turbomachine. The method eliminates problems encountered in obtaining solutions with the velocity gradient equation when large gradients in velocity occur through the blade row. With the improved method, results indicate that the transonic solution can be obtained by scaling the velocities obtained at the reduced mass flow rate where all velocities are subsonic thereby eliminating the need for a solution of the velocity gradient equation. Solutions obtained with the scaling method on a two dimensional compressor cascade and an axial turbine stator show good agreement with experimental data. The results obtained for the stationary blade rows and comparison of analytical results obtained with and without the present method suggest that the method will yield an improved solution for centrifugal compressor impellers.

Wood, J. R.↗
NASA NTRS1981

Engine dynamic analysis with general nonlinear finite-element codes. I Overall approach and development of bearing damper element

NASA-sponsored research on engine dynamic simulation using general finite element nonlinear time transient computer codes available on the open market is reviewed. The approach taken was to develop software packages to model engine components which are not typically found on dynamical structures and are therefore not already computer codes. The software package developed for squeeze-film bearing dampers is outlined, and the results of a parametric study of damper pressure for a variety of specified circular orbits are presented for both long-bearing and short-bearing solutions. The data from a four-degree-of-freedom rotor-damper-stator model under conditions of small rotor unbalance through large rotor unbalance are also given.

Adams, M. L.↗
NASA NTRS1981

In-flight jet engine noise measurement system

An instrumentation system in flight tests for noise research is described which utilizes miniature transducers to measure low-amplitude, high-frequency fluctuating pressures in a jet engine mounted under the wing of a turboprop aircraft. The system employs a rotor-mounted FM telemeter to acquire data from eight fan-blade-mounted transducers which are subjected to up to 75,000 g's of loading. Data is transmitted from the rotor to an antenna mounted in the inlet-duct wall using a low-power, close-coupled RF link. The blade pressures and other inlet and stator-vane fluctuating pressures are recorded on airborne, magnetic-tape recorders. The flight instrumentation described also includes PCM techniques to encode and record a variety of quasi-static measurements to provide engine and aircraft performance data. The instrumentation and experimental measurements are of value to an improved understanding of noise sources in jet engines and for the advancement of jet-engine ground noise testing techniques.

Knight, V. H., Jr.↗
NASA NTRS1981

Command profile for Galileo scan platform control

A recursive command profile is developed for the control of a two-degree-of-freedom scan platform mounted on a flexible structure. Perfect sensors and actuators are assumed for development and testing, and structural vibrations are minimized by actuator torque commands following a smooth torque-time profile. The integral of the smooth torque profile, the rate profile, is recursively generated by a piecewise constant second derivation, and the torque applied by the closk actuator is divided into three components. Results show that the smooth platform motion in response to the command profiles is what the Galileo control systems needs to avoid stator structural vibrations. Position, rate and acceleration profiles are also presented, and the resulting motion of the scan platform in response to command profiles is illustrated.

Man, G. K.↗
NASA NTRS1981

Core compressor exit stage study. Volume 4: Data and performance report for the best stage configuration

The core compressor exit stage study program develops rear stage blading designs that have lower losses in their endwall boundary layer regions. The test data and performance results for the best stage configuration consisting of Rotor-B running with Stator-B are described. The technical approach in this efficiency improvement program utilizes a low speed research compressor. Tests were conducted in two ways: (1) to use four identical stages of blading to obtain test data in a true multistage environment and (2) to use a single stage of blading to compare with the multistage test results. The effects of increased rotor tip clearances and circumferential groove casing treatment are evaluated.

Wisler, D. C.↗
NASA NTRS1981

Core compressor exit stage study. Volume 5: Design and performance report for the Rotor C/Stator B configuration

Rear stage blading designs that have lower losses in their endwall boundary layer regions were developed. The design of rotor-C and the performance results for rotor-C running with stator B are described. A low speed research compressor is utilized as the principal investigative tool. Four identical stages of blading are used to obtained data in a true multistage environment.

Wisler, D. C.↗
NASA NTRS1982

The use of optimization techniques to design controlled diffusion compressor blading

A method for automating compressor blade design using numerical optimization, and applied to the design of a controlled diffusion stator blade row is presented. A general purpose optimization procedure is employed, based on conjugate directions for locally unconstrained problems and on feasible directions for locally constrained problems. Coupled to the optimizer is an analysis package consisting of three analysis programs which calculate blade geometry, inviscid flow, and blade surface boundary layers. The optimizing concepts and selection of design objective and constraints are described. The procedure for automating the design of a two dimensional blade section is discussed, and design results are presented.

Sanger, N. L.↗
NASA NTRS1980

Advanced Gas Turbine (AGT) powertrain system initial development report

The powertrain consists of a single shaft regenerated gas turbine engine utilizing ceramic hot section components, coupled to a slit differential gearbox with an available variable stator torque converter and an available Ford intergral overdrive four-speed automatic transmission. Predicted fuel economy using gasoline fuel over the combined federal driving cycle (CFDC) is 15.3 km/1, which represents a 59% improvement over the spark-ignition-powered baseline vehicle. Using DF2 fuel, CFDC mileage estimates are 17.43 km/1. Zero to 96.6 km/hr acceleration time is 11.9 seconds with a four-second accleration distance of 21.0 m. The ceramic radial turbine rotor is discussed along with the control system for the powertrain.

Source record↗
NASA NTRS1982

Cooled variable-area radial turbine technology program

The objective of this study was a conceptual evaluation and design analyses of a cooled variable-area radial turbine capable of maintaining nearly constant high efficiency when operated at a constant speed and pressure ratio over a range of flows corresponding to 50- to 100-percent maximum engine power. The results showed that a 1589K (2400 F) turbine was feasible that would satisfy a 4000-hour duty cycle life goal. The final design feasibility is based on 1988 material technology goals. A peak aerodynamic stage total efficiency of 0.88 was predicted at 100 percent power. Two candidate stators were identified: an articulated trailing-edge and a locally movable sidewall. Both concepts must be experimentally evaluated to determine the optimum configuration. A follow-on test program is proposed for this evaluation.

Large, G. D.↗
NASA NTRS1982

CF6 Jet Engine Diagnostics Program: High pressure compressor clearance investigation

The effects of high pressure compressor clearance changes on engine performance were experimentally determined on a CF6 core engine. The results indicate that a one percent reduction in normalized average clearance, expressed as a fraction of airfoil length, improves compressor efficiency by one percent. Compressor clearances are reduced by the application of rotor bore cooling, insulation of the stator casing, and use of a low coefficient of expansion material in the aft stages. This improvement amounts to a reduction of normalized average clearance of 0.78 percent, relative to CF6-60 compressor, which is equivalent to an improvement in compressor efficiency of 0.78 percent.

Radomski, M. A.↗