Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solutions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
DOE OSTI2022

Thin film combinatorial sputtering of Al-Ce alloys: Investigating the phase separation of as-deposited solid solutions and determining the coefficient of thermal expansion

Al x Ce 100–x thin films with a composition range of ~75.0 < x < 99.5 at% (36.5 < x < 97.5 wt%) were synthesized via combinatorial co-sputtering from an Al and an Al 50 Ce 50 target. The crystal structure, phase fraction, film morphology, electrical resistivity, and temperature-dependent coefficients of thermal expansion (CTE) are all correlated to the Al x Ce 100–x composition. The as-deposited films form a metastable solid-solution, and annealing leads to the formation of the thermodynamically stable two-phase system of Al and the α-Al 11 Ce 3 intermetallic. Temperature dependent x-ray diffraction (XRD) reveals that the two phases expand independently of one another, and the thin film Al temperature-dependent CTE is similar to bulk Al. The thin film Al 11 Ce 3 intermetallic phase has a nearly constant CTE of ~1.5 × 10 –5 /°C within the temperature range studied (25–550 °C). To confirm the thin film Al 11 Ce 3 results, bulk stoichiometric Al 11 Ce 3 and +/- 1 wt% Ce samples were prepared and the CTE of each was measured with the same conditions. A Rietveld analysis of the bulk data enabled an estimation of the CTE in each of the 3 orthorhombic lattice parameters, which displayed anisotropic behavior. The thin film and bulk CTE measurements were in very good agreement. Estimations of the temperature dependent CTE of the two-phase alloys are made via the Reuss and Voigt models. Finally, by demonstrating the efficacy of the approach, more complex multi-component rapid materials discovery of low CTE Al-alloys can be pursued via the combinatorial thin film synthesis and XRD measurement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Unexpected Conformational Behavior of Poly(poly(ethylene glycol) methacrylate)-Poly(propylene carbonate)-Poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA) Amphiphilic Block Copolymers in Micellar Solution and at the Air-Water Interface

Self-assemblies (bulk micelles and Langmuir monolayers) of a new amphiphilic block copolymer, poly(poly(ethylene glycol) methacrylate)-poly(propylene carbonate)-poly(poly(ethylene glycol) methacrylate) (PPEGMA-PPC-PPEGMA), were investigated in dilute aqueous solution and at the air-water interface. An important feature that distinguishes PPEGMA-PPC-PPEGMA from conventional linear PEG-based polymer surfactants is that in the hydrophilic PPEGMA block the PEG moieties exist as side chains attached to the poly(methacrylate) (PMA) backbone. This study was performed using three PPEGMA-PPC-PPEGMA samples having an identical PPC molecular weight (5.6 kDa) and different PPEGMA molecular weights (7.3, 2.8 and 2.1 kDa on either side) (named as “G7C6G7”, “G3C5G3”, and “G2C6G2”, respectively). Cryo-TEM images revealed that G2C6G2 micelles form large clusters, whereas G7C6G7 micelles exist as unimers; the behavior of G3C6G3 is intermediate. The average core surface distance between two adjacent G2C6G2 micelles in a cluster was estimated to be only about 3.7 nm, which suggests that in the micelle corona layer only the PEG side chains (but not the PMA backbone) exist as hydrated brush chains. A calculation showed that at the small micelle separation distance observed, the van der Waals attractive forces become significant, and are thus likely responsible for the cluster formation. Steady shear rheometry measurements confirmed that G2C6G2 micelles are indeed only weakly bound in clusters, and these micelle clusters are thus prone to breakup even under mild steady shear. The micelle breakup force estimated from the shear viscosity data is in reasonable agreement with an estimate obtained from the theoretical van der Waals interaction potential. Langmuir monolayers formed at the air-water interface by PPEGMA-PPC-PPEGMA were also characterized; surface pressure-area measurements were performed. Detailed features of the surface pressure-area isotherms further supported that only the PEG side chains are hydrated in the subphase, while the PMA backbone remains unhydrated and situated on the water surface.

Lee, Jaewon↗
DOE OSTI2024

Specific iron binding to natural sphingomyelin membrane induced by non-specific co-solutes

Sphingomyelin (SPM), a crucial phospholipid in the myelin sheath, plays a vital role in insulating nerve fibers. We hypothesize that iron ions selectively bind to the phosphatidylcholine (PC) template within the SPM membrane under near-physiological conditions, resulting in disruptions to membrane organization. These interactions could potentially contribute to the degradation of the myelin sheath, thereby playing a role in the development of neurodegenerative diseases. We utilized synchrotron-based X-ray spectroscopy and diffraction techniques to study the interaction of iron ions with a bovine spinal-cord SPM monolayer (ML) at the liquid-vapor interface under physiological conditions. The SPM ML serves as a model system, representing localized patches of lipids within a more complex membrane structure. The experiments assessed iron binding to the SPM membrane both in the presence of salts and with additional evaluation of the effects of various ion species on membrane behavior. Grazing incidence X-ray diffraction was employed to analyze the impact of iron binding on the structural integrity of the SPM membrane. Furthermore, our results demonstrate that iron ions in dilute solution selectively bind to the PC template of the SPM membrane exclusively at near-physiological salt concentrations (e.g., NaCl, KCl, KI, or CaCl 2 ) and are pH-dependent. In-significant binding was detected in the absence of these salts or at near-neutral pH with salts. The surface adsorption of iron ions is correlated with salt concentration, reaching saturation at physiological levels. In contrast, multivalent ions such as La 3+ and Ca 2+ do not bind to SPM under similar conditions. Notably, iron binding to the SPM membrane disrupts its in-plane organization, suggesting that these interactions may compromise membrane integrity and contribute to myelin sheath damage associated with neurological disorders.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Synthesis of multicomponent oxygen evolution reaction coatings via block copolymer templating with vapor- and solution-phase precursors

Porous mixed transition metal oxide heterostructures are promising electrocatalysts due to their high surface area. However, achieving conformal multicomponent oxide coatings with controlled nanoscale architectures remains challenging. Here, we report a synthesis strategy that integrates solution-based swelling infiltration (SBI) with gas-phase sequential infiltration synthesis (SIS) in a block copolymer template to fabricate porous, high-surface-area, conformal mixed-oxide electrocatalytic coatings. In this approach, a PS75-P4VP25 block copolymer (BCP) film is first infiltrated with transition metal acetylacetonate precursors via SBI, followed by exposure to gas phase precursors of ZnO via SIS process. Thermal annealing of the infiltrated BCP films converts them into all-inorganic Fe–ZnO, Fe–Co–ZnO, and Fe–Ni–ZnO coatings. Electrochemical testing on 70 nm thick conformal coatings demonstrates promising oxygen evolution reaction (OER) activity in alkaline media, with mass-specific current densities up to 1.0 × 10 5 mA/g at an overpotential of 330 mV (vs. RHE) at ultralow loading (~0.005 g/cm 2 ). Among the compositions, Fe–Co–ZnO and amorphous Fe–Ni–ZnO show the best OER performance, delivering current densities of 2.00 and 3.04 mA/cm 2 , respectively, compared to 1.52 mA/cm 2 for Fe–ZnO.. This work establishes SBI–SIS as a versatile route for fabricating nm-thin, high-performance multicomponent oxide heterostructures on cost-efficient supports, enabling efficient catalyst utilization in electrochemical energy conversion application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Local Lagrangian reduced-order modeling for the Rayleigh-Taylor instability by solution manifold decomposition

The Rayleigh-Taylor instability is a classical hydrodynamic instability of great interest in various disciplines of science and engineering, including astrophysics, atmospheric sciences and climate, geophysics, and fusion energy. Analytical methods cannot be applied to explain the long-time behavior of the Rayleigh-Taylor instability, and therefore, numerical simulation of the full problem is required. However, in order to capture the growth of amplitude of perturbations accurately, both the spatial and temporal discretizations need to be extremely fine for traditional numerical methods, and long-time simulation may become prohibitively expensive. In this paper, we propose efficient reduced order model techniques to accelerate the simulation of the Rayleigh-Taylor instability in compressible gas dynamics. Here, we introduce a general framework for decomposing the solution manifold to construct the temporal domain partition and temporally-local reduced order model construction with varying Atwood number. We propose two practical approaches in this framework, namely decomposition by physical time and by penetration distance. Numerical results are presented to examine the performance of the proposed approaches.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Activation of dislocations in Mg with solute Y

Mg-Y cast alloy shows excellent ductility (elongation to failure > 15%) compared with pure Mg and commercial Mg cast alloys. By monitoring the microstructure evolution during an in situ tensile test of a Mg-2.5 wt%Y alloy, we identify the activation of prismatic slip, which is rare in Mg. Synchrotron X-ray micro-beam Laue diffraction (μ-Laue) and transmission electron microscopy revealed the morphology of prismatic slip bands and individual dislocations. Density functional theory and molecular dynamics calculations indicate that solute Y can significantly reduce the stacking fault energy (SFE) along direction on prismatic plane in Mg lattice and thus facilitate the nucleation of dislocations during deformation. The presence of free dislocations in the Mg lattice can also lead to nucleation of {10–12} twins even under unfavorable geometric conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dislocation loop evolution and radiation hardening in nickel-based concentrated solid solution alloys

Effects of chemical composition, ion irradiation dose and temperature on unfaulting of irradiation induced Frank dislocation loops to perfect loops in two nickel based single-phase solid solution alloys, Ni–20Fe and NiFe–20Cr, have been studied. The fraction of Frank loops decreases with irradiation dose from 7.2 to 38.4 dpa at 500°C, but with more Frank loops remaining in the ternary alloy. However, perfect loops and dislocation networks become the dominant features of defects at 580°C in both alloys. The results indicate a thermally assisted loop unfaulting process that may be hindered by more sluggish defect motion in the alloy with more chemical components. Nano-indentation with both continuous stiffness method and single indentation method are used to measure radiation hardening. Loop unfaulting in both alloys irradiated at 580°C reduced radiation hardening while significant hardening is observed after irradiation at 500°C. The quasi-static single indentation method exhibits lower hardness results compared to continuous stiffness method, because dislocations induced from the cyclic loading in the latter method get relaxed and stabilized, resulting in higher resistance to the indenter.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Solute segregation and precipitation across damage rates in dual-ion–irradiated T91 steel

We report that dual-ion irradiations using 5.0 MeV defocused Fe 2+ ions and co-injected energy degraded 2.00 to 2.85 MeV He 2+ ions were conducted on a Fe9CrMo ferritic-martensitic steel T91 to 17 dpa at a damage rate range of 5 × 10 -5 dpa/s to 3 × 10 -3 dpa/s at 445°C, followed by characterization of the microstructure using conventional and scanning transmission electron microscopy. Radiation induced Ni/Si clusters and radiation induced segregation were quantified using energy dispersive X-ray spectroscopy at each condition and were compared with the same material irradiated in the BOR-60 reactor and in the as-received condition. No significant Cr segregation was found at lath boundaries after dual-ion irradiation, while Ni and Si enrichments both decreased with increasing damage rate leading to a sharp decrease in the density of Ni/Si clusters with damage rate. Increased point defect recombination at higher ion damage rates likely reduced the Ni/Si cluster density compared with BOR-60. Although the overall vacancy concentration and diffusion are enhanced by the irradiation damage rate, the lack of time for thermal diffusion and ballistic displacements of solutes are significant limiting factors for Ni/Si cluster formation. This work demonstrates the effect of irradiation damage rate on elemental segregation and clustering when using ion irradiation to simulate reactor irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase stability, mechanical properties, and ion irradiation effects in face-centered cubic CrFeMnNi compositionally complex solid-solution alloys at high temperatures

We report two CrFeMnNi face-centered cubic complex concentrated solid-solution alloys (CSA) have been evaluated for phase stability, mechanical properties, and radiation damage effects from heavy ions. Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 were predicted by thermodynamic calculations to phase separate and maintain a single phase at 700 °C, respectively. Aging experiments at this temperature confirmed varying degrees of precipitation of a body-centered cubic phase in both Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe 35 Mn 15 Ni 35 . The alloys showed promising strength in tensile deformation at room temperature, with yield strengths of 155 MPa and 151 MPa for Cr 18 Fe 27 Mn 27 Ni 28 and Cr 15 Fe3 5 Mn 15 Ni 35 , respectively. At 500 °C, the yield strength of Cr 18 Fe 27 Mn 27 Ni 28 fell to 93 MPa, and to 100 MPa in Cr 15 Fe3 5 Mn 15 Ni 35 . Unlike Cr 18 Fe 27 Mn 27 Ni 28 , Cr 15 Fe 35 Mn 15 Ni 35 gained some ductility at 500 °C compared to room temperature. The two CSAs were irradiated to 75 dpa at 500 °C in the plateau region of the displacement curve using 3.7 MeV Ni 2+ ions, alongside model alloy 709 as a reference. Irradiation results produced similar densities and sizes of dislocations loops in the two CSAs compared to the reference. However, while large voids form in the plateau region of Cr 18 Fe 27 Mn 27 Ni 28 , small voids form just beyond the displacement peak of Cr 15 Fe 35 Mn 15 Ni 35 . Atom probe tomography and energy dispersive X-ray spectroscopy-equipped scanning transmission electron microscopes were used to characterize the alloys for changes in chemical distribution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Helium interaction with solutes and impurities in neutron-irradiated nanostructured ferritic alloys: A first principles study

Density functional theory calculations are performed to explore the binding between He and alloying solutes, impurities, and transmutation products expected in neutron irradiated nanostructured ferritic alloys (NFAs), here 14YWT is taken as an example. Elements that exhibit significant binding (attraction) with an interstitial He are Y (binding energy = 0.46 eV), Mg (0.32), O (0.33), Ti (0.16), and C (0.15). Those that provide significant binding to a substitutional He are O (1.44), Y (1.24), N (0.73), H (0.56), Mg (0.52), Ti (0.34), Si (0.34), C (0.33), Al (0.32), Ni (0.26), Ta (0.23), and Mn (0.16). The presence of these elements in Fe matrix could reduce the transport of He towards oxide particles, dislocations, and internal boundaries, and could promote He bubble nucleation in the matrix. For convenience, we compile existing binding energy data of He with He n and He n V (He-vacancy) clusters. Dissociation pathway analysis reveals that, in general, the most likely dissociation of a He n V cluster is by a sequential emission of individual He atoms. Furthermore, larger bubbles are more prone to dissociation than smaller ones. In addition, we estimate the binding energy (segregation energy) of He in bulk Y 2 Ti 2 O 7 (YTO) single crystal, YTO/Fe interface, and YTO particle embedded in Fe, with respect to interstitial He in Fe, from existing formation energies of He in these structures. We also compile available data of He binding with Fe self-interstitial atom (SIA), SIA clusters, and edge and screw dislocations. Note that given the absence of DFT data, the binding with SIA clusters and dislocations are gathered from simulations with empirical potentials. Finally, the data presented in this paper is important to inform multiscale simulations of He bubble accumulation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of electrolyte solutions on carbon dioxide fixation in single chamber Al–CO 2 battery

Governments and research & development (R&D) organizations are actively initiating various programs and research strategies for CO 2 capture, its utilization, and integration with long duration energy storage from renewable sources worldwide. In line with the carbon capture goals, here we report a novel electrochemical Al-CO 2 battery cell, that can simultaneously capture CO 2 and convert it into value-added products, in addition to long-duration energy generation and storage. Here, this innovative approach employs cost-effective Al metal as an anode and an in-house synthesized Ni–Fe based bimetallic double hydroxide catalyst as the cathode, with meticulously optimized compositions and morphologies. We explore the impact of different aqueous electrolyte solutions compositions on the cell performance, demonstrating up to 10 h of stable long duration energy storage with a stable voltage profile. The cell exhibits low polarization even at high current densities of up to 12 mA cm -2 and maintains stable cycling over 500 h. Through Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray Diffraction and X-ray photoelectron spectroscopy (XPS) analysis, we determined that the discharge product is either NaAlCO 3 (OH) 2 or KAlCO 3 (OH) 2 , distinct from the Al 2 (CO 3 ) 3 typically reported in conventional Al–CO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Shared micromobility as a first- and last-mile transit solution? Spatiotemporal insights from a novel dataset

The first- and last-mile (FM/LM) problem is a major deterrent to public transit use. With the rise of shared micromobility options such as shared e-scooters in recent years, there is a growing interest in understanding their potential to serve as a last-mile transit solution. However, empirical data regarding the integrated use of shared micromobility and public transit have been limited so far. As a result, much is unknown regarding the spatiotemporal patterns and characteristics of shared micromobility trips serving as an FM/LM connection to transit. Here, this paper addresses these knowledge gaps by leveraging a novel dataset (i.e., the Spin post-ride survey dataset) that records thousands of transit-connecting shared e-scooter trips in Washington DC. Specifically, we used the dataset to reveal the spatiotemporal patterns of transit-connecting shared e-scooter trips in Washington DC, resulting in some major policy insights regarding the integral use of shared e-scooters and public transit. We further leveraged the dataset to validate if and to what extent a commonly applied buffer-zone approach can infer FM/LM micromobility trips accurately. Statistical tests showed that the actual FM/LM Spin e-scooter trips differ from inferred FM/LM Spin e-scooter trips in both spatial and temporal dimensions. This indicates that the common practice of inferring FM/LM micromobility trips with a buffer-zone approach can lead to inaccurate estimates of transit-connecting micromobility trips.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Spectroscopic features of dissolved iodine in pristine and gamma-irradiated nitric acid solutions

While iodine speciation is important for a wide range of nuclear activities, understanding the mechanisms of the transformations of iodine between chemical forms and the sensitivity of these transitions to solution conditions and exposure to radiation remains an active area of research. This work curates spectroscopic data from several experimental techniques and establishes their sensitivity and limitations in detecting changes in iodine speciation in both neutral and acidic regimes. The techniques include Raman spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, 127 I NMR spectroscopy, and ultraviolet-visible (UV-Vis) spectroscopy. Analysis of these data indicates that these commonly accessible spectroscopies often have dynamic ranges of measurable concentrations that do not always overlap between all techniques. The experimental techniques are disparately sensitive to iodide (I - ), molecular iodine (I 2 ), iodate (IO 3 - ), and periodate (IO 4 - ) species. Raman, FTIR, and NMR spectra were subsequentially analyzed using two-dimensional correlation analyses to generate high-resolution autocorrelation spectra. Here, the use of these spectroscopies is then extended to tracking acidification-induced and gamma irradiation-induced transformations of dissolved sodium iodate in deionized water and concentrated nitric acid. Both dissolution into nitric acid and irradiation with a gamma source are demonstrated to perturb the iodine speciation promoting their assembly into molecular iodine (I 2 ) and/or triiodide (I 3 - ). While I 2 and I 3 - species are undetectable with FTIR spectroscopy and 127 I NMR spectroscopy, the species can be detected with UV-Vis spectroscopy, and in some instances, I 3 - can be detected with Raman spectroscopy in the low wavenumber region. Ultimately, the results of this work provide a path to designing optimal combinations of techniques to detect forms of iodine across a wide range of concentrations and conditions.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Deformation mechanisms in single crystal Ni-based concentrated solid solution alloys by nanoindentation

Nanoindentation is a critical technique to probe mechanical properties at the micrometer and sub-micrometer scales, accompanied by challenges from indentation size effect, pile-up/sink-in effect, and strain rate sensitivity. In this work, different nanoindentation techniques have been employed to explore Ni-based concentrated solid solution alloys (CSAs) with the addition of 3d transition metal elements including Co, Cr, Mn, and Fe, including unique single-crystal Ni, NiCo, NiFe, Ni 80 Cr 20 , and NiCoFeCr samples with (100) surfaces. A procedure of nanoindentation tests and data analysis/correction have been developed, and a data set of hardness, elastic modulus, strain rate sensitivity, and activation volume for Ni-based CSAs are provided, including the less explored binary alloys such as Ni 80 Cr 20 and Ni 80 Mn 20 . The results show that the type of alloying elements is more critical than the number of elements in strengthening: Co does not provide strengthening in NiCo, while Cr, Mn, and Fe are effective strengthening elements. Cr is the most effective among all the 3d transition metal elements. Furthermore, atomic-level lattice distortion is responsible for the strengthening and the role of stacking fault energy is insignificant in Ni-based CSAs at room temperature. In summary, nanoindentation shows increasing promise as a reliable and fast tool to provide comprehensive mechanical information for new alloy design and development.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling magnetic fields with helical solutions to Laplace’s equation

The series solution to Laplace's equation in a helical coordinate system is derived and refined using symmetry and chirality arguments. These functions and their more commonplace counterparts are used to model solenoidal magnetic fields via linear, multidimensional curve-fitting. A judicious choice of functional forms, a small number of free parameters and sparse input data can lead to highly accurate, fine-grained modeling of solenoidal magnetic fields, including helical features arising from the winding of the solenoid, with overall field accuracy at better than one part per million.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

CTF: A modernized, production-level, thermal hydraulic solver for the solution of industry-relevant challenge problems in pressurized water reactors

CTF is a thermal hydraulic (T/H) subchannel tool that has been extensively developed over the past ten years as part of the Consortium for Advanced Simulation of Light Water Reactors (CASL) program. The code was selected early in the CASL program for support of high-impact challenge problems that were found to be relevant to the nuclear industry and its currently operating fleet of pressurized water reactors (PWRs), including issues such as departure from nucleate boiling (DNB), crud-induced power shifts (CIPSs), and reactivity-insertion accidents (RIAs). By incorporating CTF into the multiphysics Virtual Environment for Reactor Application (VERA) core simulator software developed by CASL, CTF has become the primary means of providing fluid and fuel thermal feedback, as well as T/H figure-of-merits (FOMs) in large-scale reactor simulations. With the goal of solving industry challenge problems, CASL placed great emphasis on developing high-quality, high-performance, validated software tools that offer higher fidelity than what is currently possible with current industry methods. In support of this effort, CTF was developed from a research tool into an nuclear quality assurance (NQA-1)–compliant, production-level software tool that is capable of addressing the stated challenge problems and goals of CASL. This work presents a review of the major technological achievements that were realized in developing CTF over the past decade of the CASL program and presents an overview of the code solution approach and closure models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Demand-side solutions in the US building sector could achieve deep emissions reductions and avoid over $100 billion in power sector costs

Buildings are energy-intensive and a primary source of US end-use sector carbon emissions. Although building emissions today are 25% below their 2005 peak, far deeper reductions are needed to reach the US 2050 net-zero emissions goal. However, plausible decarbonization pathways that consider both buildings and their interactions with the power grid remain poorly understood. Here, we couple detailed modeling of building energy use and the grid to quantify building decarbonization potential and associated grid impacts. We find up to a 91% reduction in building CO 2 emissions from 2005 levels by 2050 using a portfolio of building efficiency, demand flexibility, and electrification measures alongside rapid grid decarbonization. Building efficiency and flexibility could generate up to $107 billion in annual power system cost savings by 2050, offsetting over a third of the incremental cost of full grid decarbonization. Our results underscore multiple benefits of demand-side solutions for deep decarbonization of US buildings.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗