Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Effects of higher harmonic control on rotor performance and control loads

An analytical study, based on an advanced Higher Harmonic Control (HHC) analysis for helicopter rotor systems, is carried out to investigate HHC application for rotor performance enhancement. The effects of HHC on stall characteristics of rotor and blade pitch-link loads when the system is configured to suppress vibration are also examined. For vibration control, simulated results indicate that HHC may promote early blade stall. Effects of blade torsion frequencies on HHC performance are moderate, and torsionally stiff blades require less actuator power than torsionally soft blades. For rotor performance improvement, a 3 to 5 percent reduction in rotor shaft power can be achieved with 2 deg of two-per-rev blade pitch control.

Nguyen, Khanh↗

Control of an aircraft in downbursts

Guidance schemes are designed to approximate the optimal survival and optimal performance paths through downbursts, which were determined in the previous paper. Specifically, climb-rate command following is used to achieve performance, and altitude command following is used to enhance survivability. Nonlinear simulations are conducted to investigate the effects of the climb-rate command and altitude command. Takeoff flight is considered and full thrust is assumed. In a mild to moderate downburst, an aircraft can follow a constant, smaller-than-nominal climb rate without stall. Better survival capability is achieved by climbing at a lower rate accompanied by lower altitude, and vice versa. In a severe downbursts, the aircraft must descend to avoid stall. The farther it descends, the higher the survival capability, but the poorer the performance. If the downburst is very severe, the best strategy is to descend immediately to the lowest safe altitude. Since the intensity of a downbursts is hard to evaluate prior to penetration, it is advisable to keep a high airspeed. Therefore, use of the survival strategy is recommended that employs maximum thrust and allows the aircraft to descend to a safe minimum altitude immediately upon entering a downburst on takeoff.

Zhao, Yiyuan↗

Exploratory wind tunnel investigation of the stability and control characteristics of a three-surface, forward-swept wing advanced turboprop model

The purpose of the present investigation was to parametrically study the stability and control characteristics of a forward-swept wing three-surface turboprop model through an extended angle of attack range, including the deep-stall region. As part of a joint research program between North Carolina State University and NASA Langley Research Center, a low-speed wind tunnel investigation was conducted with a three-surface, forward-swept wing, aft-mounted, twin-pusher propeller, model, representative of an advanced turboprop configuration. The tests were conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. The model parameters varied in the test were horizontal tail location, canard size, sweep and location, and wing position. The model was equipped with air turbines, housed within the nacelles and driven by compressed air, to model turboprop power effects. A three-surface, forward-swept wing configuration that provided satisfactory static longitudinal and lateral/directional stability was identified. The three-surface configuration was found to have greater longitudinal control and increased center of gravity range relative to a conventional (two-surface) design. The test showed that power had a large favorable effect on stability and control about all three axis in the post-stall regime.

Coe, Paul L., Jr.↗

The adverse aerodynamic impact of very small leading-edge ice (roughness) buildups on wings and tails

Systematic experimental studies were performed to establish the aerodynamic impact of very small leading-edge simulated ice (roughness) formations on lifting surfaces. The geometries studied include single element configurations (airfoil and 3-D tail) as well as multi-element high-lift airfoil geometries. Emphasis in these studies was placed on obtaining results at high Reynolds numbers to insure the applicability of the findings to full-scale situations. It was found that the well-known Brumby correlation for the adverse lift impact of discrete roughness elements at the leading edge is not appropriate for cases representative of initial ice build up (i.e., distributed roughness). It was also found that allowing initial ice formations of a size required for removal by presently proposed deicing systems could lead to maximum lift losses of approximately 40 percent for single-element airfoils. Losses in angle-of-attack margin to stall are equally substantial - as high as 6 degrees. Percentage losses for multi-element airfoils are not as severe as for single-element configurations, but degradations of the angle-of-attack-to-stall margin are the same for both.

Lynch, Frank T.↗

Interactive-Boundary-Layer Computations For Oscillating Airfoil

Interactive-boundary-layer method developed for computations of steady flow, extended under assumption of quasi-steady flow, to computations of evolution of two-dimensional flow about oscillating airfoil under light-dynamic-stall conditions. Represents advance toward ability to compute unsteady flows at even greater angles of attack with solutions of equations normally used for description of boundary-layer flows on airfoils prior to stall. Important in practical studies of flow on blades of helicopter rotors, axial compressors, and turbines.

Carr, L. W.↗

Efficient simulation of incompressible viscous flow over multi-element airfoils

The incompressible, viscous, turbulent flow over single and multi-element airfoils is numerically simulated in an efficient manner by solving the incompressible Navier-Stokes equations. The computer code uses the method of pseudo-compressibility with an upwind-differencing scheme for the convective fluxes and an implicit line-relaxation solution algorithm. The motivation for this work includes interest in studying the high-lift take-off and landing configurations of various aircraft. In particular, accurate computation of lift and drag at various angles of attack, up to stall, is desired. Two different turbulence models are tested in computing the flow over an NACA 4412 airfoil; an accurate prediction of stall is obtained. The approach used for multi-element airfoils involves the use of multiple zones of structured grids fitted to each element. Two different approaches are compared: a patched system of grids, and an overlaid Chimera system of grids. Computational results are presented for two-element, three-element, and four-element airfoil configurations. Excellent agreement with experimental surface pressure coefficients is seen. The code converges in less than 200 iterations, requiring on the order of one minute of CPU time (on a CRAY YMP) per element in the airfoil configuration.

Rogers, Stuart E.↗

Characteristics of two sharp-nosed airfoils having reduced spinning tendencies

According to Mr. L.D. Bell, of the Consolidated Aircraft Corporation, certain undesirable spinning characteristics of a commercial airplane were eliminated by the addition of a filler to the forward part of the wing to give it a sharp leading edge. To ascertain what aerodynamic effects result from such a change of section, two airfoils having sharp leading edges were tested in the variable-density wind tunnel. Both sections were derived by modifying the Gott. 398. The tests, which were made at a large value of the Reynolds Number, were carried to very large angles of attack to provide data for application to flight at angles of attack well beyond the stall. The characteristics of the sharp-nosed airfoils are compared with those of the normal Gott. 398 airfoil. Both of the sharp-nosed airfoils, which differ in the angle between the upper and lower surfaces at the leading edge, have about the same characteristics. As compared with the normal airfoil, the maximum lift is reduced by approximately 26 per cent, but the objectionable rapidly decreasing lift with angle of attack beyond the stall is eliminated; the profile drag of the section is slightly reduced in the range of the lift coefficient between 0.2 and 0.85, but at higher and lower lift coefficients the drag is increased.

Jacobs, Eastman N↗

The effects of full-span and partial-span split flaps on the aerodynamic characteristics of a tapered wing

The investigation was made to determine the effects of full-span and of partial-span split flaps on the aerodynamic characteristics of a tapered wing. Aerodynamic force tests were made in the N.A.C.A. 7 by 10 foot wind tunnel on a highly tapered Clark Y wing equipped with various split flaps. Two sizes of tapered-chord flaps were tested as full-span flaps, and a narrow tapered-chord flap was tested as a partial-span flap by cutting off portions first from the tip and then from the center. The investigation showed that with full-span split flaps the lift and drag characteristics of the tapered wing up to the stall are similar to those of a rectangular wing with flaps of comparable size, but that the stall of the tapered wing with full-span flaps occurs at progressively lower angles of attack with increasing flap deflection up to that for maximum lift. For partial-span tapered split flaps on a tapered wing it was found that the maximum lift is greater, and the lift-drag ratio at maximum lift is less, when the partial-span flap is located at the center of the wing than when it is located at the tip portion.

Wenzinger, Carl J↗

Pressure-distribution investigation on an NACA 0009 airfoil with a 30-percent-chord plain flap and three tabs

Pressure-distribution tests of an NACA 0009 airfoil with a 30-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made. The purpose of these tests was to continue an investigation to supply structural and aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as diagrams of resultant pressures and of resultant-pressure increments for the airfoil with the flap and the 20-percent-chord tab. Increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs are also given. At all unstalled flap and tab deflections, the experimental distributions agree well with those calculated by an analytical method. The agreement is poor, however, then the stalled or the unstalled condition of the flap or tab deflected alone was changed to an unstalled or stalled condition by the simultaneous deflection of both the flap and the tab.

Ames, Milton B↗

Control of airplanes at low speeds

Loss of control over the orientation of an airplane as the incidence approaches and enters the region of stalled flight is a prolific cause of serious accidents. This report discusses methods of landing at slow speeds approaching stall.

CONTROL AT LOW SPEEDS↗

Notes on the Stability and Control of Tailless Airplanes

Problems involved in the stability and control of tailless airplanes are discussed. Such factors as the location of the aerodynamic center and its effect on the longitudinal stability, longitudinal trim with high-lift devices, the effects of various changes in the shape of the wing on lateral stability, and the effects of nacelles are covered. It appears that sufficient stability and controllability can be secured without sweepback. With sweepback, a flap over the center section of the wing may be used to serve the dual purpose of elevator control and high-lift device. Sweepback introduces undesirable stalling characteristics, however, and may require auxiliary devices to prevent stalling of the tips.

Jones, Robert↗

Investigation of Blade-row Flow Distributions in Axial-flow-compressor Stage Consisting of Guide Vanes and Rotor-blade Row

A 30-inch tip-diameter axial-flow compressor stage was investigated with and without rotor to determine individual blade-row performance, interblade-row effects, and outer-wall boundary-layer conditions. Velocity gradients at guide-vane outlet without rotor approximated design assumptions, when the measured variation of leaving angle was considered. With rotor in operation, Mach number and rotor-blade effects changed flow distribution leaving guide vanes and invalidated design assumption of radial equilibrium. Rotor-blade performance correlated interpolated two-dimensional results within 2 degrees, although tip stall was indicated in experimental and not two-dimensional results. Boundary-displacement thickness was less than 1.0 and 1.5 percent of passage height after guide vanes and after rotor, respectively, but increased rapidly after rotor when tip stall occurred.

COMPRESSORS - AXIAL FLOW↗

A study of the use of leading-edge notches as a means for improving the low-speed pitching-moment characteristics of a thin 45-degree swept wing of aspect ratio 4

In an effort to develop a simple but effective means for controlling the stall progression of swept wings, a low-speed investigation has been undertaken primarily to determine the effectiveness of leading-edge notches. The investigation included consideration of notch size, location, and shape, as well as combined effects of notch—chord-extension and notch-fence arrangements. The wing used in the study had 45° quarter-chord sweep, aspect ratio 4, taper ratio 0.3, and NACA 65A006 airfoil sections streamwise. The results of the investigation indicated that although substantial improvements were obtained in the wing pitching-moment characteristics at moderate angles of attack, by use of outboard leading-edge notches, none of these notches produced desirable wing stability characteristics throughout the angle-of-attack range. The wing pitching-moment characteristics were relatively insensitive to notch size and to small changes in span-wise location. The use of a notch at the inboard end of a chord-extension increased the effectiveness of the chord-extension near stall and produced the same results as a chord-extension having an equivalent inboard overhang. Small localized notch—chord-extension combinations were found to produce the same pitching-moment characteristics as much larger chord-extension configurations. A leading-edge root cutout used in conjunction with a small outboard notch—chord-extension combination resulted in fairly desirable overall wing pitching-moment characteristics.

Joseph Weil↗

Investigation of Two-Stage Counterrotating Compressor. III: Design of Second-Stage Rotor and Preliminary Over-All Performance

At the design speed of a two-stage counterrotating compressor, an overall average pressure ratio of 4.3 was obtained at a specific weight flow of 27.2 pounds per second per square foot frontal area with an adiabatic efficiency of 0.75. Preliminary tests indicate that a weight-flow mismatching exists between the two rotors that causes the first rotor to operate at less than peak efficiency at design speed. At lower speeds, the first stage was forced to operate in the stalled region in single-stage tests. With the second rotor installed, no periodic rotating stall was observed, although random fluctations of similiar magnitude were noted.

Wilcox, Ward W↗

Interference of Tail Surfaces and Wing and Fuselage from Tests of 17 Combinations in the N.A.C.A. Variable-Density Tunnel

An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment of the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angle and as losses in the tail effectiveness and varies with the geometry of the combination. An interference burble, which markedly increases the glide-path angle and the stability in pitch before the actual stall, may be considered a means of obtaining satisfactory stalling characteristics for complete combination.

Sherman, Albert↗

Flight Measurements to Determine Effect of a Spring-Loaded Tab on Longitudinal Stability of an Airplane

In conjunction with a program of research on the general problem of stability of airplanes in the climbing condition, tests have been made of a spring-loaded tb which. is referred to as a ?springy tab,? installed on the elevator of a low-wing scout bomber. The tab was arranged to deflect upward with decrease in speed which caused an increase in the pull force required to trim at low speeds and thereby increased the stick-free static longitudinal stability of the airplane. It was found that the springy tab would increase the stick-free stability in all flight conditions, would reduce the danger of inadvertent stalling because of the definite pull force required to stall the airplane with power on, would reduce the effect of center-of-gravity position on stick-free static stability, and would have little effect on the elevator stick forces in accelerated f11ght. Another advantage of the springy tab is that it might be used to provide almost any desired variation of elevator stick force with speed by adjusting the tab hinge-moment characteristics and the variation of spring moment with tab deflection. Unlike the bungee and the bobweight, the springy tab would provide stick-free static stability without requiring a pull force to hold the stick back while taxying. A device similar to the springy tab may be used on the rudder or ailerons to eliminate undesirable trim-force variations with speed.

TABS, ELEVATOR↗

Measurements in Flight of the Lateral-Control Characteristics of an Airplane Equipped with Full-Span Zap Flaps and Simple Circular-Arc-Type Ailerons

Flight tests were conducted on the OS2U-2 seaplane with simple circular-arc-type ailerons directly connected to the actuating torque tube. Two aileron test installations were made, differing only in the inclination of the projecting surface with the wing's upper surface. The lateral-control characteristics of the airplane were determined from data obtained in stalls and rudder-fixed aileron rolls. The revised ailerons were deficient in maximum rolling effectiveness, but were capable of controlling the rolling tendencies of the airplane near the stall.

AILERON CONTROLS - VOUGHT OS2U-2↗

Effects of Compressibility on the Maximum Lift Characteristics and Spanwise Load Distribution of a 12-Foot-Span Fighter-Type Wing of NACA 230-Series Airfoil Sections

Lift characteristics and pressure distribution for a NACA 230 wing were investigated for an angle of attack range of from -10 to +24 degrees and Mach range of from 0.2 to 0.7. Maximum lift coefficient increased up to a Mach number of 0.3, decreased rapidly to a Mach number of 0.55, and then decreased moderately. At high speeds, maximum lift coefficient was reached at from 10 to 12 degrees beyond the stalling angle. In high-speed stalls, resultant load underwent a moderate shift outward.

PRESSURE DISTRIBUTION - AIRFOILS-NACA 23016↗