SEARCH · Engineering Papers
Results for “REACTOR FUELING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
EPRI/INL TCF Project on LOCA Analysis Tool: Statement of Work
Through the U.S. Department of Energy (DOE) Technology Commercialization Fund (TCF), Electric Power Research Institute (EPRI) and Idaho National Laboratory (INL) are partnering to develop an analysis tool focused on loss-of- coolant accident (LOCA) behavior of light-water reactor (LWR) fuel rods. This tool will involve a coupling of RELAP5- 3D and Bison. This report gives details of the work to be performed in this partnership. It is hoped that industry and national laboratory experts, including the Collaborative Research on Advanced Fuel Technology (CRAFT) Technical Expert Group (TEG), will provide feedback on the planned work.
Review of Available Critical Experiments and Critical Experiments Facilities to Perform High-Assay Low-Enriched Uranium Fuel Transport Validation for Advanced Reactor Deployment
Explore the source record for details and available documents.
High-burnup Experiments in Reactivity Initiated Accidents (HERA)
HERA is a joint experimental program (JEEP) operating within the Nuclear Energy Agency’s (NEA’s) framework for irradiation experiments (FIDES). HERA is dedicated to the understanding of light water reactor (LWR) fuel performance at high burnup under reactivity-initiated accidents (RIA). During RIAs the fuel cladding can be breached by one of two mechanisms; pellet-cladding mechanical interaction or high temperature balloon and rupture. Pellet-cladding mechanical interaction (PCMI) failure occurs in the early phase of an RIA transient where the fuel pellet expands rapidly into the cladding prior to any meaningful heat transfer from the pellet to the cladding. This results in high stresses in the cladding resulting in crack propagation through the base Zircaloy metal and axially along the cladding tube. Failure by PCMI is a brittle failure mode and occurs at low cladding strains, approximately 2% hoop strain. If the cladding survives the PCMI phase of the transient, it may still fail due to ballooning and rupture induced by extended exposure to high temperature. Thermal transport from the fuel pin to the coolant is significantly reduced if a transition to film boiling on the cladding surface occurs. This result in both a rapid increase in fuel temperature, which drives fission gas release, and a spike in cladding temperature, which results in loss of mechanical strength. If the internal pressure of the fuel rod is greater than the system pressure the cladding can inelastically deform and eventually rupture. Failure by swelling and rupture occurs at larger strains, generally greater than 5% hoop strain. While PCMI failures are generally seen as more limiting, the dominance of one failure mode over the other can be affected by both the cladding material conditions, and the transient evolution.
Mortar-based Cohesive Zone Model with Application to TRISO Particle Debonding
The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. This report outlines work towards the development of an integrated, mortar-based cohesive zone framework with mechanical contact. We model debonding of tri-structural isotropic (TRISO) layers using a mortar approach, extending the framework used for mechanical contact, using weighted quantities. A bilinear mixed mode traction approach, already used in Jiang et al. (2021), is applied analogously herein to model debonding between TRISO particle layers. The examples include the debonding of the inner pyrolytic carbon (IPyC) from the silicon carbide (SiC) layers, as well as partial and full debonding of the buffer from the IPyC layers. Both 2D and 3D examples are utilized to demonstrate the superior numerical performance of the new mortar approach, which allows for modeling arbitrarily meshed interfaces (i.e., non-matching discretizations).
Development of a BISON validation case for the TRISO transient irradiations in NSRR using effective heat capacity methods
The current tristructural isotropic (TRISO) fuel assessment and validation database in BISON primarily covers steady- state irradiation and high-temperature furnace testing. Transient assessment cases are potentially needed to support U.S. industry efforts in designing and deploying commercial reactors using TRISO fuels. Historical transient tests in- volving TRISO fuels used highly conservative conditions compared to the typical high-temperature gas-cooled reactor accident scenarios. Despite this, modeling historical transient tests is fundamental for evaluating BISON’s predictive capabilities, adapting material properties for high-temperature and high-particle-power regimes, and developing a sys- tematic validation approach for TRISO transient applications. This work developed a 1D model of transient experiments carried out at the Nuclear Safety Research Reactor using BISON. BISON’s predictions of energy deposition, UO 2 melting onset, and molten volume fractions are compared against experimental measurements. Melting was modeled using an effective specific heat capacity model for UO 2 . We found that BISON’s predictions are in reasonable agreement with experimental data for low-energy-deposition cases, and that BISON overpredicts melting at higher energy depositions. We also discuss the potential causes of discrepancies between the simulated and measured results and propose ways to further develop the model. Although these simulations used conservative conditions compared to those expected for actual TRISO-fueled reactors, they extended the range of conditions reflected in the data in the existing BISON database for TRISO fuels.
Effect of D2O on increasing the neutron flux near a fueled capsule in the Plum Brook Mock-Up Reactor
Deuterium oxide effect on increasing neutron flux near fueled capsule in nuclear reactor core
Thermal Model of Oxide Growth for Full Size Fuel Plate Experiments in the Advanced Test Reactor
The full-size plate number one (FSP-1) irradiation test designed for irradiation testing of plate type fuel is planned to be irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This FSP-1 experiment is a non-instrumented drop-in test where aluminum-clad fuel plates are cooled directly by the ATR Primary Coolant System (PCS) water. This experiment is one of a series of experiments being irradiated at ATR for the United States High Performance Research Reactor (USHPRR) program. This fueled experiment contains aluminum-clad fuel full-size plates consisting of monolithic U-10Mo. Previous thermal analyses have been documented concerning oxide growth [1] and thermal safety margins [2] for similar U-10Mo mini plate experiments. This analysis is part of the thermal safety analysis of the experiment to be irradiated in ATR. Departure from nucleate boiling ratio (DNBR) and flow instability ratio (FIR) have been calculated for the flow coastdown condition 2 and the reactivity insertion accident condition-2 (RIA2) transient. The purpose of this paper is to investigate the thermal margin of the fuel meat during a RIA2 transient when oxide has accumulated on the plate surfaces acting as an insulator.
Updated Reference VTR Core for CD-1
A preliminary reference core design was previously developed for the Versatile Test Reactor. The main features are that it is a 300 MW th sodium-cooled fast reactor using ternary metallic fuel U-20Pu-10Zr and able to achieve peak fast fluxes (E n > 0.1 MeV) in excess of 4.0x10 15 n/cm 2 -s. The plutonium in the fuel was assumed to be “reactor grade”, with a fissile quality of about 72% (i.e., 239 Pu and 241 Pu comprise 72% of the plutonium isotopes), and the uranium was assumed to be low-enriched uranium with 5% 235 U. This preliminary core design has been used through the CD-0 phase of the VTR project. Progression of the work after CD-0 led to revising, updating and refining the reference VTR core design, based on considerations from the various VTR teams: fuel, experiment, safety, and plant design teams. The objective of this report is to summarize the various changes made and details added to the model, to provide a description of the updated reference VTR core design and of its performance characteristics. This includes the traditional reactor physics characteristics, fuel cycle details, reactivity coefficients, temperature distributions, control rod worths and shutdown requirements. All of these define the updated “reference VTR core” intended to be used through CD-1.
Compact 30 kW circulating helium capsule for fuel element tests in NASA Plum Brook reactor
In pile and out of pile durability tests and characteristics of 30 kW circulating helium fuel capsules in Plum Brook Reactor
Wettability and CHF limits of Accident-Tolerant nuclear fuel cladding materials in light water reactor conditions
Here, we present the results of experimental investigations aimed at evaluating the thermal–hydraulic performance of chromium-coated zircaloy, i.e., one of the most promising accident tolerant fuel (ATF) cladding material for light water nuclear reactors. Precisely, we investigate the wettability and critical heat flux (CHF) limits of chromium-coated and conventional zircaloy surfaces in prototypical reactor conditions. For both surface types, we measure the contact angle in a vapor-saturated atmosphere from ambient pressure to the operating pressure of pressurized water reactors (PWRs), i.e., ~15 MPa. We measure the ambient-pressure steady-state flow boiling CHF with a spatially uniform heat flux. We measure the high-pressure steady-state flow boiling CHF with a cosine shape heat flux (up to 20 MPa) and with a uniform heat flux (up to 15 MPa), also exploring the effect of CRUD deposits on the chromium-coated surface. Our results reveal that the chromium surface and the bare zircaloy surface have similar wettability and both become super-hydrophilic in PWR conditions, and that there is practically no difference in the steady-state CHF limits, both at low-pressure and high-pressure conditions, also when the chromium-coated surface is covered by a CRUD deposit. However, while the chromium-coating does not improve the CHF compared to the bare zircaloy surface, it improves the post-CHF behavior. The chromium coating prevents the reaction between zircaloy and steam, which results in the formation of a brittle zirconium oxide through the surface of the cladding. We also measure the transient CHF under exponentially escalating heat flux inputs of a nano-smooth and a rough surface mimicking a chromium-coated zircaloy cladding. Interestingly, the results of the transient heat flux tests suggest that the CHF limit for very short periods (i.e., fast transients) is independent of the surface finish, being the same for a rough chromium surface or a nano-smooth surface.
Combined TREAT-LOC and SATS LOCA Experiment Plan: Integral LOCA Experiments on High-Burnup Fuels
The Transient Reactor Test Facility (TREAT) loss-of-coolant (LOC) and high-burnup (HBu) experiment series, along with the Severe Accident Test Station (SATS) HBu experiment series, are integral LOC accident (LOCA) experiments planned under the DOE AFC program, which aim to support burnup extension needs by addressing identified R&D priorities in order to achieve an improved understanding of fuel fragmentation, relocation, and dispersal (FFRD) of HBu fuel during LOCA events. The data produced under this plan will be used to further validate and confirm existing models and inform future R&D and model development. The experimental program has been specifically designed to address knowledge gaps and opportunities identified through a detailed review of existing public knowledge on LOCA FFRD. The test program employs a unique combination of in- and out-of-pile experimental approaches and state-of-the-art facilities to provide a clear connection to the existing integral and semi-integral LOCA experiment database. The primary goal of the program is to investigate the impact of prototypic HBu fuel/cladding thermomechanical behaviors under postulated LWR LOCA conditions that have not yet been fully studied. These conditions correspond with prototypic decay-energy heatup (DEH) and stored-energy heatup (SEH) conditions. Importantly, TREAT’s unique capability will enable the first evaluation of the impact of SEH conditions on HBu fuels. The test program will emphasize the development of an improved mechanistic understanding of key experimental phenomena through independent experimental systems, development of a database to support fuel performance modeling tools and employing world-leading advanced materials characterization and in-situ diagnostics to evaluate FFRD. The results of the program will provide novel data to support modeling development and validation and will represent a significant advancement in evaluating prototypic conditions, as well as to inform the technical basis for LOCA-induced FFRD.
Metallic fuel transient fuel-cladding interface liquefaction model assessment platform enabled by integrating BISON with databases
A novel platform has been developed within the BISON fuel performance code to assess models of fuel-cladding interface liquefaction for sodium-cooled fast reactor (SFR) metallic fuels. Here, this platform is crucial because liquefaction at the fuel-cladding interface significantly impacts fuel performance and may compromise fuel pin integrity during transient events. To ensure accurate predictions, the platform integrates data collected during the Integral Fast Reactor (IFR) program, now archived in metallic fuel databases. This integration supports verification and validation (V&V) of the models in BISON. Leveraging the extensive US experience with metallic fuel liquefaction and the collections of preserved legacy data, the platform serves as a powerful tool for evaluating existing models and advancing the development of new ones.
MSR Fuel Salt Qualification Methodology
This report documents the continuing activities at Oak Ridge National Laboratory (ORNL) in support of the US Nuclear Regulatory Commission (NRC) efforts to develop an efficient, appropriate process for liquid fuel salt system qualification. Fuel qualification for salt-cooled molten salt reactors (MSRs) is part of the ongoing coated particle fuel qualification effort. Fuel qualification is a process which provides high confidence that physical and chemical behavior of fuel is sufficiently understood so that it can be adequately modeled for both normal and accident conditions, reflecting the role of the fuel design in the overall safety of the facility. Uncertainties are defined so that calculated fission product releases include the appropriate margins to ensure conservative calculation of radiological dose consequences. The initial phase of ORNL’s activities is documented in ORNL/LTR-2018/1045 Molten Salt Reactor Fuel Qualification Considerations and Challenges.
CFD analysis of a solid pin-fueled small modular fluoride salt-cooled reactor
A computational fluid dynamics (CFD) study is performed for the pre-conceptual solid pin-fueled small modular fluoride salt-cooled reactor developed by the Oak Ridge National Laboratory (ORNL). The solid and fluid regions in a 1/12th section of a fuel assembly are modeled. The solid region includes fuel and non-fuel pins, with heat generation in the active region of the fuel pins. Two different power profiles, uniform and center-peaked, are considered. The FLiBe coolant flows from the bottom to the top of the core, parallel to the bank of fuel and non-fuel pins. The k-ω shear-stress transport (SST) model is chosen as the baseline turbulence model. The effects of grid refinement, inlet turbulence specification, and turbulence models on the temperature and pressure drop predictions are studied. Turbulence model sensitivity is investigated by comparing the results from the k-ω SST model with other two-equation models (k-ω baseline or BSL and k-ε realizable) as well as with anisotropic Reynolds stress transport models (linear pressure-strain and stress-BSL). Here the results show that the choice of turbulence model has a significant impact on the pin temperature and bundle pressure drop predictions. The results from the baseline turbulence model show good agreement between the fuel pin temperatures and bundle pressure drop values predicted using a subchannel model previously developed by the authors of the present study.
Multiphysics Simulation of the NASA SIRIUS-CAL Fuel Experiment in the Transient Test Reactor Using Griffin
After approximately 50 years, NASA is restarting efforts to develop nuclear thermal propulsion (NTP) for interplanetary missions. Building upon nuclear engine tests performed from the late 1950s to the early 1970s, the present research and testing focuses on advanced materials and fabrication methods. A number of transient tests have been performed to evaluate materials performance under high-temperature, high-flux conditions, with several more experiments in the pipeline for future testing. The measured data obtained from those tests are being used to validate the Griffin reactor multiphysics code for this particular type of application. Griffin was developed at Idaho National Laboratory (INL) using the MOOSE framework. This article describes the simulation results of the SIRIUS-CAL calibration experiment in the Transient Reactor Test Facility (TREAT). SIRIUS-CAL was the first transient test conducted on NASA fuels, and although the test was performed with a relatively low core peak power, the test specimen survived a temperature exceeding 900 K. Griffin simulations of the experiment successfully matched the reactor’s power transient after calibrating the initial control rod position to match the initial reactor period. The thermal-hydraulics model largely matches the time-dependent response of a thermocouple located within the experiment specimen to within the uncertainty estimate. However, the uncertainty range is significant and must be reduced in the future.
2020 Status Report - Research Reactor Infrastructure Program
This presentation will discuss the purpose and scope of the Department of Energy - Research Reactor Infrastructure (RRI) Program. Personnel involved in the program will be introduced and contact information will be provided for team member. Information will be provided to conference attendees as to the status of the core activities of the program. These activities include fresh fuel element fabrication and spent nuclear fuel shipment returns to the DOE. Current and future issues pertinent to the RRI program will also be presented. The RRI program maintains fuels support contracts and provides nuclear reactor fuel at no or low cost to 24 U.S. universities operating a total of 25 reactor facilities. These facilities include: - Twelve TRIGA facilities - Eight plate fueled facilities - Three AGN facilities - One Pulstar fueled facility - One Critical facility The title for the fuel remains with the United States government and when the universities are finished with the fuel, the fuel is returned to the United States government for long-term storage. Mission of the Research Reactor Infrastructure Program: The Research Reactor Infrastructure Program is funded by the U.S. Department of Energy, Office of Nuclear Energy and is managed by the Idaho National Laboratory (INL) in Idaho Falls, Idaho. The program goals are: - Keep all U.S. operating university reactor programs supplied with nuclear fuel. - Provide assistance for movement of irradiated nuclear fuel from U.S. universities, after the DOE receipt facility authorizes the fuel receipt.
Verification of the 3-Region Advanced Test Reactor MCNP Model
The verification of the 3-region homogenized fuel Advanced Test Reactor MCNP model. The 3-region model was compared to the 19-plate model found in the 94-CIC report. Flux tallies, energy deposition tallies, and quarter core mesh tallies were used to compare the two models. The 3-region model needed updating in order to make good comparisons between the models. The percent error from the flux and energy deposition tallies data shows that experiment positions inside the flux trap have higher errors than positions outside the fuel ring. The standard deviation data obtained from the mesh tallies shows that the two models agree within two standard deviations throughout the reactor. It is concluded that the model works adequately for what it is used for.