Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Influence of Thermomechanically Controlled Processing on Microstructure and Hydrogen Induced Cracking Susceptibility of API 5L X70 Pipeline Steel

The effect of different thermomechanical controlled processing routes on susceptibility of X70 pipeline steel to hydrogen induced cracking (HIC) have been studied. Two X70 pipeline steel specimens labelled WE and WD were investigated. These specimens have the same chemical composition, but they were processed with seperate thermomechanical treatments parameters. Microstructural examinations showed that WE consists of mainly acicular ferrite and polygonal ferrite, while WD consists of acicular ferrite and bainitic ferrite. After subjecting both specimens to hydrogen charging for 12 and 16 h in 0.2 M sulfuric acid and 3 g/L ammonium thiocyanate, early onset of HIC was observed in specimen WD. Post-hydrogen charging microstructural evaluation showed the nucleation of discontinuous cracks in WD after 12 h of charging. However, extended charging for up to 16 h resulted in HIC along the mid-thickness region of both specimens. Hydrogen diffusion across specimen WE was better than that of specimen WD. Therefore, hydrogen trapping at grain boundaries, banded deformed grains, inclusions and secondary phases such as martensite and cementite aided initiation and propagation of HIC in specimens. Nevertheless, the adverse effect of these features on HIC risks was more prominent in specimen WD compared to specimen WE. The Vickers microhardness values measured in WD (349.6 HV) and WE (307.4 HV) suggest that WD is harder than WE; and higher kernel average misorientation of 0.66° in WD than in WE (0.58°) shows higher dislocation density in WD. The results from slow strain rate tensile test confirmed that specimen WD was stronger and more susceptible to HIC than specimen WE. It was concluded that microstructural phases developed during thermomechanical processing improved strength in WD at the expense of its crack resistance, while WE with lower strength showed more ductility and higher resistance to HIC.

36 MATERIALS SCIENCE↗

Mechanism of Decrease in Impact Toughness in a Low-Carbon MnCrMoNiCu Plate Steel with Increasing Austenitizing Temperature

In order to reveal how microscopic factors affect the toughness and the occurrence of cleavage fracture of a low-carbon MnCrMoNiCu alloyed steel, a series of thermal treatments was performed on the steel employing a thermomechanical simulator. These involved reheating samples at different temperatures (950-1250 °C), producing different prior austenite sizes, followed by a continuous cooling transformation process. The Charpy V-notch toughness was determined, and the effect of austenite grain size on the ductile-to-brittle transition temperatures of the steel was investigated. The microstructural evolution on the austenite sizes was studied, fracture features were characterized, the critical event for cleavage fracture was identified, and the local cleavage fracture stress σ{sub f} was calculated. The impact toughness decreased as the austenitizing temperature increased. A quantitative relationship between σ{sub f} and the size of the initial cleavage fracture facet (microcrack nucleus) a{sub f} in the lathy martensite + bainite microstructure has been developed.

36 MATERIALS SCIENCE↗

Effects of Heating and Quenching Processing Parameters on Phase Transformation of 55CrMo Steel

Microstructure and mechanical properties after induction hardening have a significant effect on the wear resistance performance and lifetime of 55CrMo steel ball screw. In the paper, the dilatometric curves were recorded at the different heating rate by a Gleeble-1500D thermo-mechanical simulator to determine the effect of heating rate on the austenitizing temperature of 55CrMo steel. Heat treatment of some specimens was performed by the Gleeble-1500D thermal simulator at the different heating temperature, holding time and cooling rate to investigate the effect of induction hardening parameters on the phase transformation, microstructure and microhardness of 55CrMo steel. Microstructure of specimen was analyzed using an optical microscope and a scanning electron microscope. Volume fraction of retained austenite was measured using an x-ray diffractometer. The mechanical properties were evaluated by a microhardness tester. The results show that the austenitizing temperature of 55CrMo steel increases with the increasing heating rate. Increasing the heating temperature, holding time and cooling rate of specimen is helpful in obtaining a uniform cryptocrystalline martensite. Volume fraction of retained austenite is less as the heating temperature is in the range of 900-950 °C. In the induction hardening of 55CrMo steel, the heating temperature should be in the range of 900-1000 °C.

36 MATERIALS SCIENCE↗

A Hybrid Plasma Treatment of H13 Tool Steel by Combining Plasma Nitriding and Post-Oxidation

Pulsed plasma nitriding and post-oxidizing process have been applied to hot work H13 tool steel to enhance the tribological properties (friction coefficient and wear rate). Nitriding was accomplished under specific conditions to generate a free white layer surface in order to avoid an abrasive wear mechanism. Post-oxidizing treatment was carried out in the same reactor after finishing the nitriding treatment; processing time was varied for 30 and 60 min. The morphology, phase’s composition and wear performance of duplex-treated samples were evaluated by scanning electron microscopy, x-ray diffraction analysis and pin-on-ball wear technique. The results show that the duplex treatment produces a bilayer arrangement constituted by an 80 μm diffusion zone with expanded martensite as the main phase underneath a 2–4 μm hematite–magnetite-oxidized layer. The duplex treatment modified the main wear mechanism of the nitrided sample from abrasive to plastic yielding. The changes in wear mechanisms resulted in a noticeable decrease, about 40%, in friction coefficient for oxidized samples in comparison with the nitrided-only sample. It was also established that the lowest friction coefficient values can be obtained when hematite is the main phase in the oxidized layer.

36 MATERIALS SCIENCE↗

Laser Powder Deposition Parametric Optimization and Property Development for Ti-6Al-4V Alloy

In this study, Ti6Al4V alloy was produced via laser powder deposition (LPD). To obtain Ti6Al4V alloy with maximum density, LPD parameters for preparing Ti6Al4V samples were optimized using the Taguchi method. Results were analyzed on the basis of the signal-to-noise (S/N) ratios and analyses of variance. A high energy density should be used to achieve higher levels of densification. The optimal combination of parameters for density was a scanning speed of 550 mm/min, laser power of 160 W, powder feeding rate of 0.99 g/min, and shield gas flow of 8 L/min. An almost fully dense Ti6Al4V sample was prepared using the optimized LPD process, and the relative density was greater than 99%. In addition, the microstructure and properties of Ti6Al4V samples prepared by optimized LPD process were investigated. The microstructure investigation revealed that the LPD-prepared Ti6Al4V sample was predominantly composed of fine acicular α phase and lath-type α phase. Tensile and microhardness tests indicated that the LPD sample had higher mechanical properties than the traditional cast Ti6Al4V alloy because of the acicular martensitic phase and smaller grain size.

36 MATERIALS SCIENCE↗

Formability, Microstructure and Mechanical Properties of Flow-Formed 17-4 PH Stainless Steel

The subject of the research that has been conducted in this paper was to analyze precipitation-hardened martensitic stainless steel 17-4 PH after flow forming with four different strains and subsequent standard heat treatment. Four cylinders were obtained with a 16, 30, 48 and 68% reduction in thickness, respectively. The samples were analyzed in terms of their mechanical properties and microstructural changes before and after the heat treatment. The results showed that a higher strain resulted in an overall higher strength (up to 1200 MPa UTS) and refinement of the structure, although at a cost of the elongation. High deformation influenced the precipitation process, and the ratio of the grain boundaries significantly increased. Nonetheless, comparing the obtained results with other similar research, it seems that the formation of nano-precipitates of Cu is the key-strengthening mechanism. Strain hardening contributes to an increase in the strength of the steel, although the effect decreases after heat treatment. The relatively small values of residual stress in the steel, especially after the heat treatment, confirmed these claims. Overall, flow forming allowed high deformations of the 17-4 PH steel to be obtained although it did not significantly change the mechanical properties of the material due to the dominant precipitation hardening mechanism.

36 MATERIALS SCIENCE↗

Alternative PWHT to Improve High-Temperature Mechanical Properties of Advanced 9Cr Steel Welds

Creep-resistant 9Cr steels are extremely important in thermal power generation industry due to their marked resistance to creep and corrosion. The weldability of these alloys is critical since they are used in welded construction equipment. The required mechanical properties are achieved after post-weld heat treatment. This study examined the effect of different post-weld heat treatments on microstructure and mechanical properties of creep strength-enhanced 9Cr steel welding deposits. It was obtained with an experimental flux-cored arc welding wire used under protective gas (Ar-20% CO{sub 2}). The heat treatments used were: (1) tempering (760 °C × 2 h), (2) solubilizing (1050 °C × 1 h) + tempering (760 °C × 2 h) and (3) solubilizing (1150 °C × 1 h) + first tempering (660 °C × 3 h) + second tempering (660 °C × 3 h). All-weld metal chemical composition was analyzed, and hot tensile tests were carried out at different temperatures. Charpy-V impact tests and Vickers microhardness measurements were also performed. Microstructures were studied using x-ray diffraction and optical and scanning electron microscopy. In all cases, a martensitic matrix with intergranular and intra-granular precipitates was detected. In the as-welded condition, δ-ferrite was also found. Microhardness dropped, and the impact energy increased with post-weld heat treatments. The highest hot tensile strength result was achieved with samples submitted to austenization at 1150 °C and double tempering at 660 °C.

36 MATERIALS SCIENCE↗

Microstructure and Tensile Properties of the Fe-32%Ni-4%Co Alloy During Cryorolling and Subsequent Annealing

The Fe-32%Ni-4%Co alloy was cryorolled to produce thickness reductions of 10, 40, 60 and 90%; then, the strips with a final thickness of 0.52 mm were annealed at 893, 923 and 943 K for different soaking times. The x-ray diffraction measurements indicated that both thermally induced α′-martensite (α′-M) and deformation-induced α′-M were present in the tested alloy. The thermally induced α′-M was mainly lath-shaped, while the morphology of the deformation-induced α′-M gradually changed from lath-shaped to irregular-shaped according to transmission electron microscopy observations. After the 90% reduction due to cryorolling, the total volume fraction of α′-M reached 75.6%, and the average ultimate tensile strength (UTS{sub av.}) was significantly improved from 430.3 to 1306.8 MPa. Upon subsequent annealing at 923 K for 5 min, the tested alloy mainly consisted of a large number of fine grains and a few coarse grains (CGs). In addition, several deformed structures were also observed. As the annealing time increased to 10 and 30 min, the fraction of CGs increased, and a bimodal grain size distribution was obtained, while the deformed structures were still present. The temperature of the reverse phase transformation of α′-M → γ was lower than the recrystallization temperature, which may be the main reason for the bimodal grain distribution. With this bimodal grain structure, the alloy exhibited a combination tensile strength of 543.3 MPa and an average elongation of 34.1%.

36 MATERIALS SCIENCE↗

Processing of Ultrafine-Grained Steels by Warm Rolling and Annealing

Low-carbon microalloyed steel was subjected to warm rolling followed by rapid transformation annealing (RTA) at 800-850 °C and subcritical annealing (SCA) at 600 °C to develop ultrafine ferrite grain structures (UFFG) with grain size less than 3 μm. The present study investigated the influence of light (40%) and heavy (80%) warm rolling deformation (LWR and HWR) applied during the finishing pass of two-pass rolling schedules on the microstructural evolution after rolling and subsequent annealing treatments. RTA treatment of HWR sample at a lower intercritical temperature for an optimum duration (800 °C, 30 s) developed UFFG-martensite dual-phase structure that offered the best combination of strength (YS ~ 900 MPa and UTS ~ 1200 MPa) and ductility (25% elongation). The SCA treatment provided sufficient time to achieve a uniform distribution of carbide particles throughout the ferrite matrix. SCA treatment of HWR at 600 °C for 4 h developed UFFG-carbide structure achieving YS of 800 MPa with 20% ductility. The SCA of LWR resulted in coarser ferrite grain structures (grain size > 5 μm) having higher ductility (more than 30%) but lower strength (UTS of 400-550 MPa) as compared to RTA.

36 MATERIALS SCIENCE↗

Structure and Tribological Properties of CrTiAlCN Coatings with Various Carbon Contents

Multi-component CrTiAlCN coatings with different carbon contents were deposited on AISI M2 high-speed steels using unbalanced magnetron sputtering via adjusting the C{sub 2}H{sub 2} flow rates, and their microstructures and mechanical properties were characterized by using SEM, EDS, XRD, Vickers hardness tester and scratch tester, respectively. The tribological properties of CrTiAlCN coatings sliding against SUS440C high carbon martensitic balls were performed using ball-on-disk tribo-tester. The results showed that CrTiAlCN coatings were mainly comprised of (111) and (200) crystal orientation. The maximum hardness of coatings was 29.4 ± 1.5 GPa as the carbon content was 22.5 at.%. With an increase in the carbon content of coatings, the friction coefficients and wear rates of CrTiAlCN/SUS440C tribo-pairs were significantly reduced, and the wear mechanism of coatings changed from adhesive wear to abrasive wear.

36 MATERIALS SCIENCE↗

Development of Multilayer Sinter Cladding of Cold Work Tool Steel on Hadfield Steel Plates for Wear-Resistant Applications

Machinery components used for mining and mineral processing activities are often subjected to high impact loads and wear which have placed demands for the development of materials with high resistance to dynamic loads and aggressive wear conditions. In this study, a multilayered cladding of high alloyed cold work tool steel (X245VCrMo9-4), interlayered with Hadfield steel (X120Mn12) plates, which was also used as substrate using super-solidus liquid-phase sintering technique was investigated. A stack of the cold work tool steel powder was prepared with interlayered X120Mn12 steel plates in an alumina crucible at tap density with the substrate placed on it and was sintered in a vacuum furnace at 1250 °C at a heating rate of 10 K/min, held for 30 min under a nitrogen atmosphere at 0.08 MPa and furnace-cooled. Sample from the as-sintered cladding was subjected to austenization at 1000 °C, quenched in oil and tempered at 150 °C for 2 h. Samples were subjected to microstructural examination using optical and scanning electron microscopy. The microstructural investigations were supplemented by hardness and impact wear tests. Computational thermodynamics was used to support experimental findings. The results revealed that a near-net densification of the sintered X245 was achieved with 99.93 ± 0.01% density. The sintered X245 was characterized by a dispersion of vanadium carbonitride precipitates, especially at the grain boundaries. The heat-treated X245 sample had the highest hardness of 680 ± 7 HV30 due to the matrix of tempered martensitic microstructure when compared to as-sintered with hardness of 554 ± 2 HV30. The X245/X120 interface was characterized by diffusion of Cr, Mo, Mn and C, which resulted in metallurgical bonding between the cladded materials. The impact wear resistance of the sintered X245 was eight times that of the X120; hence, a tough and wear-resistant tool is anticipated when the X120 work hardened in service.

36 MATERIALS SCIENCE↗

Microstructure and Wear Performance of Cobalt-Containing Iron-Based Slag-Free Self-shielded Flux-Cored Wire

A new type of cobalt-containing iron-based slag-free self-shielded flux-cored wire was developed for hardfacing. The influence of cobalt additions on the microstructure and wear performance of the hardfacing was investigated. The cobalt-containing iron-based hardfacing alloy has a typical hypereutectic microstructure consisting of primary M{sub 7}(C, B){sub 3} carbide, and a eutectic of M{sub 3}(C, B) carbide and austenite (part of which subsequently transformed into martensite). Cobalt promoted the formation of austenite and changed the morphology of the primary carbide and eutectic colonies. The morphology of primary carbide became fragmented with increasing cobalt due to the possible impeding effect of cobalt to the movement of the M{sub 7}(C, B){sub 3}/liquid interface. Different structures of the eutectic carbides were observed—the chrysanthemum structure for 1.42 wt.% cobalt, the skeleton form for 2.88 wt.% cobalt, the radial stripe 4.37 wt.% cobalt and the discrete stripe for 5.75 wt.% cobalt. Wear loss of the hardfacing alloy containing 2.88 wt.% cobalt was the smallest among all the alloys, owing to the large primary large carbide and skeleton-shaped eutectic carbides, the proper amount of austenite phase separating the M{sub 7}(C, B){sub 3} and M{sub 3}(C, B) carbides, the solid solution strengthening by cobalt in the matrix, and the high hardness of the alloy. Moreover, the wear resistance has a tendency to decrease with the increase in velocity as well as load.

36 MATERIALS SCIENCE↗

Retained Austenite Attributes and Mechanical Performance of Different Compositions of TRIP Steel Alloys

The main objective of this work is to correlate the different attributes of retained austenite phase in TRIP steel structure with its mechanical properties. Three different chemical compositions were used to produce TRIP steel alloys. The first alloy contains only silicon as a carbide precipitation inhibitor; in the second alloy, silicon is partially replaced with aluminum, while in the third alloy phosphorus is added to the silicon–aluminum alloy. These compositions were proposed in order to avoid the negative effect of silicon during galvanizing. These three steel alloys were cast, homogenized, hot-forged and then subjected to intercritical annealing treatment followed by cooling and isothermal treatment in salt bath with subsequent air-cooling. Microstructural characterization, using optical microscope, SEM and XRD, along with tensile testing was carried out. Retained austenite attributes include volume fraction, carbon content, total carbon content, retained austenite transformable index and its stability coefficient against strain-induced martensite (SIM) transformation. The effect of these attributes on the mechanical properties of the studied TRIP steel alloys was evaluated using tensile test date, i.e., ultimate tensile strength (UTS), ductility, yield strength to UTS ratio, performance index and strain-hardening exponent. The variation of strain-hardening rate and strain-hardening exponent with strain was also considered. The failure behavior of the studied steel alloys was investigated using SEM on tensile-tested specimens. The results show that Si/Al-alloy has the lowest retained austenite transformable index, lowest stability coefficient against SIM transformation, highest performance index and more stable and uniform variation in strain-hardening rate and strain-hardening exponent with strain. These properties satisfy the industrial constrains of the sheets used in automotive industry relating to better mechanical properties and galvanizability.

36 MATERIALS SCIENCE↗

Tailoring Microstructure and Properties of a Superelastic Ti–Ta Alloy by Incorporating Spark Plasma Sintering with Thermomechanical Processing

A powder metallurgy Ti–35 at.% Ta alloy was produced using a spark plasma sintering process. The sintered alloy exhibited Ta-rich regions at a sintering temperature of 1100 °C. Complete diffusion of elemental powders was achieved via homogenization heat treatment at 1500 °C for 12 h, but the ductility declined drastically. The brittle behavior of the homogenized sample was due to the high-oxygen content, continuous grain boundary α-phase and high-angle grain boundaries. Excellent mechanical properties were achieved when hot forging was used along with preheating the homogenized specimen at 1100 °C. The mechanisms underlying this phenomenon were suppression of the solid grain boundary α-phase, high fraction of low-angle grain boundaries and dynamic recrystallization. Tensile strength improved to the maximum value of 868 MPa. The strain recovery ratio increased to 90% in the first cycle during a cyclic loading–unloading test. Incomplete strain recovery of the first cycle was due to the presence of the martensite phase (α″).

36 MATERIALS SCIENCE↗

Numerical Simulation of Residual Stress for Laser Welding of Ti-6Al-4V Alloy Considering Solid-State Phase Transformation

In the present work, a thermal-metallurgical-mechanical model which considered the influence of phase transformation was used to predict the residual stress field of Ti-6Al-4V after laser welding. In this model, the Johnson–Mehl–Avrami equation was used to predict diffusional solid-state phase transformations: α phase to β phase during heating and β phase to α phase during cooling. The Koistinen–Marburger equation was used to predict diffusionless solid-state phase transformation of β phase to martensite during cooling. The properties of material were obtained using a mixing rule based on the phase fraction and the property of each pure phase. By applying this model, the effect of solid-state phase transformations of Ti-6Al-4V alloy on temperature field and stress field during laser welding was considered in the simulation. In addition, experiments were carried out for comparison, which significantly verified the accuracy of the applied model.

36 MATERIALS SCIENCE↗

Effect of Boron Addition on Creep Strain during Impression Creep of P91 Steel

In an attempt to understand the effect of boron addition on creep deformation behavior under high stress and high temperature in martensitic P91 steel, impression creep tests were carried out on boron-free P91 (P91) and boron-added P91 (P91B) steels. The experimental program consisted of three steps, i.e., characterization of as-received steels by microhardness, optical microscopy (OM), transmission electron microscopy (TEM), electron backscattered diffraction (EBSD) and wavelength-dispersive spectroscopy (WDS); impression creep tests at 445 MPa and 625 °C on as-received steels; characterization at deformed plastic zones of impression-crept specimens by microhardness, OM, EBSD, TEM and WDS. Impression creep tests were run till a depth of penetration of 1.8 mm was achieved for both cases which ensured a sufficient plastic zone underneath indenter for subsequent microstructural investigations. Coarsening of M{sub 23}C{sub 6} carbides was observed in P91 steel during high-temperature creep loading, which leads to extensive strain hardening in deformed plastic region, resulting in impaired creep performance. On the contrary, dynamic recrystallization in P91B steel results in formation of small strain-free grains during creep loading which are responsible for increased resistance of the material to shear stresses during an impression creep test.

36 MATERIALS SCIENCE↗

Effect of Primary Carbides on the Sharpness of Kitchen Knives Made of 8Cr13MoV Steel

Although there are many primary carbides in the cutting edge of knives made of high-carbon martensitic steel, the effect of primary carbides on the sharpness of knives has not been clarified. In this paper, the evolution of primary carbides during the production process of 8Cr13MoV steel was presented. The effect of size and amount of primary carbides on the sharpness of knives was studied via employing rolling forging and diffusion annealing process, respectively. Results indicated that primary carbides easily fell off from cutting edge during cutting process, which would decrease the wear resistance of knives. The refinement of primary carbides could not only improve the wear resistance of cutting edge, but also weaken the fluctuation of sharpness during the service process of knives. By decreasing the amount of primary carbides, the wear resistance of knives would increase effectively, which improved the cutting performance effectively. Reducing the amount of primary carbides and refining the primary carbides in cutting edge were both effective ways to improve the sharpness of knives.

36 MATERIALS SCIENCE↗

Microstructural Evolution and Properties of 24CrNiMoY Alloy Steel Fabricated by Selective Laser Melting

24CrNiMoY alloy steel samples were fabricated by selective laser melting (SLM), and a phase transformation model was established to study the alloy steel microstructural evolution. Meanwhile, microhardness and tensile properties of 24CrNiMoY alloy steel prepared by different laser energy densities (E{sub v}) were investigated. Results indicate that the microstructural evolution of 24CrNiMoY alloy steel is consistent with the phase transformation model. The main microstructure changed from martensite to bainite with the increase in thermal cycle numbers. In addition, a suitable E{sub v} plays an important role in refining the bainite structure and improving the alloy steel properties. When the E{sub v} decreases from 210 to 140 J/mm{sup 3}, the bainite lath width reduces from 1.7 to 0.6 μm. Simultaneously, the relative density, tensile strength and microhardness of the fabricated samples increase first and decrease later. 24CrNiMoY alloy steel sample prepared by 160 J/mm{sup 3} has fine mechanical properties: The tensile strength is 850 MPa and microhardness is 360 HV{sub 0.2}.

36 MATERIALS SCIENCE↗