Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

The Effect of Grain Size on the Strain Hardening Behavior for Extruded ZK61 Magnesium Alloy

The effects of grain size on the tensile and compressive strain hardening behaviors for extruded ZK61 alloys have been investigated by uniaxial tensile and compressive tests along the extrusion directions. Cylindrical tension and compression specimens of extruded ZK61 alloys with various sized grain were fabricated by annealing treatments. Tensile and compressive tests at ambient temperature were conducted at a strain rate of 0.5 × 10{sup −3} s{sup −1}. The results indicate that both tensile strain hardening and compressive strain hardening of ZK61 alloys with different grain sizes have an athermal regime of dislocation accumulation in early deformation. The threshold stress value caused dynamic recovery is predominantly related to grain size in tensile strain hardening, but the threshold stress values for different grain sizes are almost identical in compressive strain hardening. There are obvious transition points on the tensile strain hardening curves which indicate the occurrence of dynamic recrystallization (DRX). The tensile strain hardening rate of the coarse-grained alloy obviously decreases faster than that of fine-grained alloys before DRX and the tensile strain hardening curves of different grain sizes basically tend to parallel after DRX. The compressive strain hardening rate of the fine-grained alloy obviously increases faster than that of coarse-grained alloy for twin-induced strain hardening, but compressive strain hardening curves also tend to parallel after twinning is exhausted.

36 MATERIALS SCIENCE↗

Microstructure and Deformation Mechanism of AZ31 Magnesium Alloy Under Dynamic Strain Rate

A hot-rolled AZ31Mg alloy sheet was subjected to dynamic plastic deformation parallel to the rolling direction, and microstructural evolutions and mechanical properties of the deformed samples were examined. It has been found that dynamic strain rate could facilitate {10-12} twin nucleation and growth and leads to a lower yield stress of about 20 MPa and an early end to twinning characteristic (happening at a strain point of about 6%) shown in the stress–strain curve. {10-12} twinning mechanism dominates the early plastic deformation; but when plastic strain exceeds ~ 9%, dislocation–slip mechanism instead of {10-12} twinning dominates the later plastic deformation. And this premature transformation of the dominant deformation mechanisms from {10-12} twinning to dislocation slip is caused by dynamic strain rate. The effect of dynamic strain rate on the number of twin nucleations remains unclear, and the more systematic researches are needed in the future.

36 MATERIALS SCIENCE↗

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

In this paper, cold extrusion was successfully used to fabricate the fine-grained pure Mg bar with average grain size of 2.5 μm. The microstructure, texture and mechanical properties were evaluated by electron backscattering diffraction and mechanical test. The results showed that the corresponding yield strengths for as-extruded fine-grained pure Mg were 130.8 MPa in tension and 125.6 MPa in compression, leading to a greatly improved yield asymmetry ratio. The improvement in tension–compression asymmetry is mainly due to grain refinement which favors the suppression of deformation twinning in compression and promotion of multi-deformation modes both in tension and compression at small strains.

36 MATERIALS SCIENCE↗

Workability Characteristics and Deformation Mechanisms of Die-Cast AM60 and AZ91 Magnesium Alloys: Correlation with Processing Maps

Thermo-mechanical deformation behavior of the die-cast AM60 and AZ91 alloys was assessed by performing uniaxial compression tests on Gleeble 3800 simulator under different temperatures and strain rate conditions. Low-temperature deformation behavior of both alloys was accessed at 25, 100, and 150 °C, at the strain rates of 0.1 and 1 s{sup −1}. Processing maps at a true strain of 0.5 were generated to study the intrinsic hot workability of AM60 and AZ91 alloys. Optimum processing windows were identified, and the evolution of microstructures and textures was correlated with the imposed deformation conditions. The processing map for the AM60 alloy exhibited three dynamic recrystallization (DRX) domains in the ranges: (1) 320-400 °C and 0.2-1.5 s{sup −1}, (1A) 300-325 °C and 0.1-0.2 s{sup −1}, and (2) 360-400 °C and 3-5 s{sup −1}. In Domain 1, DRX occurred predominantly by pyramidal slip and recovery mechanisms by cross-slip as confirmed by the randomized textures. Deformation in Domain 1A is by the combination of basal and prismatic slip. In Domain 2, dynamic recovery was a softening mechanism controlled by the climb. The processing map for AZ91 alloy exhibited two DRX domains in the ranges: (1) 260-310 °C and 0.1-0.5 s{sup −1} and (2) 325-350 °C and 0.8-3 s{sup −1}. The rate-controlling mechanism was climb by lattice self-diffusion in Domain 1 and by grain boundary self-diffusion in Domain 2. Both alloys exhibited flow instability at 200 and 250 °C, and therefore, they were unsuitable for processing at these temperatures.

36 MATERIALS SCIENCE↗

Effects of Heat Treatment on Microstructure, Mechanical Properties, Corrosion Resistance and Cytotoxicity of ZM21 Magnesium Alloy as Biomaterials

The effects of heat treatment on microstructure, mechanical properties, corrosion resistance and cytotoxicity of extruded Mg-2Zn-1Mn (wt.%) alloy were investigated for biomedical application in this study. The extruded alloy was T4 treated at 510 °C for 4 h and T5 treated at 200 °C for 16 h separately. The extruded Mg-Zn-Mn alloy mainly consists of Mg{sub x}Mn{sub y} phases. After T4 treatment, the amount of Mg{sub x}Mn{sub y} phases decreases and average grain size rises from 8 to 24 μm. After T5 treatment, Mg{sub 7}Zn{sub 3} phase newly precipitates along the grain boundaries and the size of grain remains similar. Compared with the T4-treated samples, the extruded and T5-treated samples exhibit higher mechanical properties. The T5-treated samples have an ultimate tensile stress of 273 MPa and an elongation of 19.7%. On the other hand, T4-treated samples present higher corrosion resistance in electrochemical tests. The degradation rates of extruded, T4-treated and T5-treated samples are 0.44 mm/year, 0.48 mm/year and 0.50 mm/year, respectively, in Ringer’s solution at 37 ± 0.2 °C. In addition, T4-treated alloy does not induce toxicity to the L-929 cells in in vitro cytotoxicity test.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Property Inhomogeneities of a Modified AZ80 Magnesium Alloy Wide Plate Under Horizontal Flat Die Extrusion

In the present paper, inhomogeneities in the microstructure and mechanical properties of a modified AZ80 plate under industrial production conditions were investigated. The results indicated that the microstructure of the edge and middle region shows more homogeneous and fine recrystallized grains. Additionally, more coarse recrystallized grains existed between the edge and the middle region. The ultimate tensile strength and yield strength of the edge region of the plate are maximal (287 and 162 MPa), and those near the 1/8 W region are minimal (259 and 152 MPa). The grain size increased from 19.5 to 27.2 μm along the center layer to the surface layer. The ultimate tensile stress (yield stress) increases from 258 (121 MPa) to 284 MPa (176 MPa) in the direction from the surface layer to the middle layer. The microhardness decreased from the surface layer (72HV) to the center layer (64HV). The metal strain state and temperature distribution lead to different degrees of dynamic recrystallization, which causes the microstructure and mechanical properties of the plate.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Mechanical Properties of the AZ91 Magnesium Alloy with Sr and Ti Additions in the As-Cast and As-Aged Conditions

Effect of different amounts of Sr and Ti additions with T6 heat treatment on microstructure and mechanical properties of the AZ91 alloy was investigated. The microstructure of the AZ91 alloy is consisted of the α-Mg phase surrounded by the semicontinuous network of β-Mg{sub 17}Al{sub 12} intermetallics. The average grain size and volume fraction of β phase decreased up to 1 wt.% Sr and 0.1 wt.% Ti additions. Exceeding Ti additions led to increase in both grain size and volume fraction. It was found that the grain refinement mechanism of AZ91 alloys with Sr additions was grain restriction factor. Also, 0.1 wt.% Ti addition could refine the grain structure of the AZ91 alloy by the formation of Al{sub 3}Ti particles that act as nucleation sites for the α-Mg phase. Furthermore, adding 1 wt.% Sr and 0.1 wt.% Ti enhanced the hardness values for both cast and aged AZ91 alloy. Moreover, ultimate tensile strength and tensile elongation values reached their maximum amounts with the 0.5 wt.% Sr and 0.1 wt.% Ti additions and more Sr and Ti additions deteriorated the mechanical properties of cast and aged AZ91 alloys. The fracture surface characterizations had good relations with the tensile properties. The fracture modes were cleavage and quasi-cleavage in the cast and aged AZ91 alloys. Furthermore, the optimum levels of Sr and Ti additions altered the fracture modes to more quasi-cleavage fractures.

36 MATERIALS SCIENCE↗

Micromechanical Fields Associated with Irregular Deformation Twins in Magnesium

Understanding and controlling the development of deformation twins is paramount for engineering strong and stable hexagonal close-packed (HCP) Mg alloys. Actual twins are often irregular in boundary morphology and twin crystallography, deviating from the classical picture commonly used in theory and simulation. In this work, the elastic strains and stresses around irregular twins are examined both experimentally and computationally to gain insight into how twins develop and the microstructural features that influence their development. A nanoprecession electron diffraction (N-PED) technique is used to measure the elastic strains within and around a $\left\{ {10\overline{1}2} \right\}$ tensile twin in AZ31B Mg alloy with nm scale resolution. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) crystal plasticity model of the same sub-grain and irregular twin structure is employed to understand and interpret the measured elastic strain fields. The calculations predict spatially resolved elastic strain fields in good agreement with the measurement, as well as all the stress components and the dislocation density fields generated by the twin, which are not easily obtainable from the experiment. The model calculations find that neighboring twins, several twin thicknesses apart, have little influence on the twin-tip micromechanical fields. Furthermore, this work reveals that irregularity in the twin-tip shape has a negligible effect on the development of the elastic strains around and inside the twin. Importantly, the major contributor to these micromechanical fields is the alignment of the twinning shear direction with the twin boundary.

36 MATERIALS SCIENCE↗

ALUMINUM IMPURITY DIFFUSION IN MAGNESIUM

The Al impurity diffusion in polycrystalline Mg (99.9%) via depth profiling with secondary ion mass spectrometry was studied in the temperature range of 673-573K, utilizing the thin film method and thin film solution to the diffusion equation. Multiple samples were utilized and multiple profiles were obtained to determine statistically confident coefficient with maximum standard deviation of 16%. Activation energy and pre-exponential factor of Al impurity diffusion in Mg was determined as 155 kJ/mole and 3.9 x 10-3 m2/sec.

36 MATERIALS SCIENCE↗

Interdiffusion in Ternary Magnesium Solid Solutions of Aluminum and Zinc

Al and Zn are two of the most common alloying elements in commercial Mg alloys, which can improve the physical properties through solid solution strengthening and precipitation hardening. Diffusion plays a key role in the kinetics of these and other microstructural design relevant to Mg-alloy development. However, there is a lack of multicomponent diffusion data available for Mg alloys. Through solid-to-solid diffusion couples, diffusional interactions of Al and Zn in ternary Mg solid-solution at 400° and 450 °C were examined by an extension of the Boltzmann-Matano analysis based on Onsager s formalism. Concentration profiles of Mg-Al-Zn ternary alloys were determined by electron probe microanalysis, and analyzed to determine the ternary interdiffusion coefficients as a function of composition. Zn was determined to interdiffuse the fastest, followed by Mg and Al. Appreciable diffusional interactions among Mg, Al, and Zn were observed by variations in sign and magnitude of cross interdiffusion coefficients. In particular, Zn was found to significantly influence the interdiffusion of Mg and Al significantly: the and ternary cross interdiffusion coefficients were both negative, and large in magnitude, in comparison to and , respectively. Al and Mg were observed influence the interdiffusion of Mg and Al, respectively, with positive and interdiffusion coefficients, but their influence on the Zn interdiffusion was negligible.

36 MATERIALS SCIENCE↗

Intragranular twinning, detwinning, and twinning-like lattice reorientation in magnesium alloys

We present that deformation twinning plays a critical role on improving metals or alloys ductility, especially for hexagonal close-packed materials with low symmetry crystal structure. A rolled Mg alloy was selected as a model system to investigate the extension twinning behaviors and characteristics of parent-twin interactions by nondestructive in situ 3D synchrotron X-ray microbeam diffraction. Besides twinning- detwinning process, the twinning-like lattice reorientation process was captured within an individual grain inside a bulk material during the strain reversal. The distributions of parent, twin, and reorientated grains and sub-micron level strain variation across the twin boundary are revealed. A theoretical calculation of the lattice strain confirms that the internal strain distribution in parent and twinned grains correlates with the experimental setup, grain orientation of parent, twin, and surrounding grains, as well as the strain path changes. In conclusion, the study suggests a novel deformation mechanism within the hexagonal close-packed structure that cannot be determined from surface-based characterization methods.

36 MATERIALS SCIENCE↗

On the origin and behavior of irradiation-induced c-component dislocation loops in magnesium

C-component dislocation loops are one of the unique defects in hexagonal close-packed (hcp) crystals that promote the accelerated growth and void formation under irradiation. In this paper, we report in situ observation of c-component dislocation loop formation in Mg under electron irradiation with emphasis on their atomic structures. Aberration-corrected scanning transmission electron microscopy imaging is utilized to reveal four possible types of double-layer loops, which were identified as different types of stacking fault and dislocation core structures. Triple- and quadruple-layer c-component dislocation loops were also observed. The formation mechanisms of the four types of double-layer loops were revealed via molecular dynamics simulations. The experimentally observed formation rate of the single- and double-layer dislocation loops is controlled by their formation energies. Finally, our direct experimental observations in combination with molecular dynamics simulations provide fundamental insight into the mechanisms governing nucleation and growth of the c-component dislocation loops as well as their interactions, which could potentially help with future development of irradiation-resistant materials.

36 MATERIALS SCIENCE↗

Role of local stresses on co-zone twin-twin junction formation in HCP magnesium

Twin-twin interactions control the formation of twin-twin junctions (TTJ) in hexagonal metals when multiple twin variants are activated in a grain. In this work, we employ a combination of two computational techniques, a 3D full-field crystal plasticity model (CP) and large-scale molecular dynamics (MD), to study the TTJ formation associated with two non-parallel {101¯2} twins in Mg. The local intra-granular stresses generated by discrete twins are computed using a spatially resolved CP model. Atomic-scale knowledge regarding formation processes and local stresses is revealed by MD. The combined analyses suggest that the twin junction forms by the migration of the boundaries of both, the impinging and impinged twin, taking place in the immediate vicinity of the contact point. It is further shown that local stress fields that are generated after initial contact promote thickening of the impinging twin, and may facilitate nucleation of a new twin on the opposite boundary of the recipient twin. In conclusion, calculations of the strain energies suggest that formation of the co-zone twin-twin junction is energetically favorable but detwinning of the TTJ upon load reversal or under cyclic loading is not.

36 MATERIALS SCIENCE↗

A comprehensive diffusion mobility database comprising 23 elements for magnesium alloys

We report that reliable experimental diffusion coefficients of 10 key alloying elements in Mg obtained by the present authors together with experimental data in the literature enabled us to perform a systematic test of the reliability of diffusion coefficients obtained from DFT calculations. The computed activation energy values were found to be quite accurate (mostly within 0.2 eV) but the computed pre-factors were less reliable. Such insights allowed us to develop a practical and yet robust strategy to perform diffusion mobility assessments by adopting the computed activation energy while fitting only the pre-factor when available experimental data are limited to a narrow temperature range. The overall good agreement between the DFT data and experimental data also gave us the confidence to employ the computed data for those that were still missing or inaccessible from experimental measurements. A systematic assessment of both the measured and computed diffusion data in hcp Mg was performed using the above holistic approach to yield the most comprehensive open Mg mobility database to date, comprising 23 elements (Mg, Ag, Al, Be, Ca, Cd, Ce, Cu, Fe, Ga, Gd, In, La, Li, Mn, Nd, Ni, Pu, Sb, Sn, U, Y, Zn). This more reliable mobility database will contribute to future development of advanced Mg alloys. The holistic approach developed in this study will be very beneficial to the future establishment of reliable mobility databases for other alloy systems as well.

36 MATERIALS SCIENCE↗

Real-time evolution of texture and temperature during friction stir processing of a magnesium alloy: An operando neutron diffraction study

The real-time development of texture and the evolution of temperature during friction stir processing (FSP) of a Mg alloy were investigated using an operando neutron diffraction measurement. A novel approach was applied in this study where the real-time, quasi-steady state measurements performed as a function of position during FSP are converted to a Lagrangian dataset that reveals the transient behavior as a function of time. The in-situ FSP was carried out under two different thermo-mechanical processing conditions represented by the Zener-Hollomon parameter, Z. Further, the results show that: (i) a shear texture develops from the initial strong basal texture with the peak temperature reaching about 774 K during a low-Z processing and (ii) a strong off-normal texture develops with a peak temperature of 616 K during a high-Z processing. Moreover, time-temperature-texture diagrams were established to reveal the real-time development of the texture during the processing for both the low Z and high Z processing conditions. The changes in texture will be discussed in terms of plastic deformation mechanisms active during various stages of the FSP under the two different processing conditions.

36 MATERIALS SCIENCE↗

Investigation of radiation enhanced diffusion of magnesium in substrates flown on the NASA genesis mission.

The thermal diffusion of an Mg implant in Si has been measured with SIMS and compared to RIMS (resonant ionisation mass spectrometry) measurements of Mg implantation and diffusion in Si wafers exposed to solar wind irradiation in the NASA Genesis mission. The Genesis samples show much more surface segregation that the samples annealed in the laboratory, due to diffusion and segregation of the implanted Mg to the heavily damaged near surface regions of the Genesis wafers. This Mg transport has been modeled by solving a set of stiff differential equations and found to agree with RIMS measurements for a Mg interstitial migration energy of 0.7 eV.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of calcium and magnesium carbonates on hydration kinetics, hydrate assemblage and microstructural development of metakaolin containing composite cements

The hydration of metakaolin composite cements containing quartz, natural limestone and dolomite rock is studied using a multi-method approach and modelling. The study demonstrates that the calcite present in limestone and dolomite rock is very reactive. Contrary, dolomite does not dissolve. Additionally to the previously reported stabilization of ettringite, the reaction of calcite introduces several changes to the mechanism of metakaolin pozzolanic reaction. Namely, the silicate and aluminate distribution among the hydrates is different. In carbonate containing samples, experimental results supported by the thermodynamic modelling suggest that the silicate mainly precipitates as low Ca/Si C-S-H and additionally the ettringite content is higher. In the case of quartz analogue, the silicates precipitate as strätlingite and C-S-H of higher Ca/Si. These changes cause lower porosity as observed by SEM-BSE and higher strength. High metakaolin reactivity results in a very dense matrix that in turn enables co-existence of phases that are thermodynamically non-compatible.

36 MATERIALS SCIENCE↗