Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

CO{sub 2} capture from simulated syngas via cyclic carbonation/calcination for a naturally occurring limestone: pilot-plant testing

Experiments were performed using a dual fluidized bed reactor system, operated in a batch mode, in order to investigate the effects of steam and simulated syngas on CO{sub 2} capture and sorbent conversion efficiency for a naturally occurring Polish calcitic limestone. In addition, the effect of high partial pressures of CO{sub 2} on the calcination process was examined using either oxygen-enriched air or oxy-fuel combustion in the calciner. As expected, calcination under oxy-fuel conditions resulted in decreased carbonation conversion due primarily to particle sintering and pore pluggage. On average there was a decrease in carbonation conversion of approximately 36.5 and 33.4% for carbonation with steam and steam/simulated syngas, respectively, compared to similar experiments using oxygen-enriched air. However, during the carbonation of the limestone with steam present in the feed gas, it was observed that the high CO{sub 2} capture efficiency period was significantly extended compared to carbonation with only CO{sub 2} present. This resulted in increased CaO conversion from approximately 16.1 to 29.7% for the initial carbonation cycle. A further increase in carbonation conversion from 29.7 to 46.9%, was also observed when simulated syngas conditions (CO, H{sub 2}) were used in the carbonator. Analysis of the outlet gases also confirmed that the calcined limestone catalyzes the water gas shift reaction, which we believe results in enhanced CO{sub 2} concentration levels at the grain surfaces of the sorbent.

01 COAL, LIGNITE, AND PEAT↗

Adsorption and diffusion of carbon dioxide on metal-organic framework (MOF-5)

Adsorption equilibrium and diffusion of CO{sub 2} on microporous metal-organic frameworks (MOF-5, or IRMOF-1) crystals were experimentally studied by the gravimetric method in the pressure range up to 1 atm. The MOF-5 crystal cubes of about 40-60 {mu} m in sizes were synthesized by the solvothermal method. Freundlich adsorption isotherm equation can fit well CO{sub 2} adsorption isotherms on MOF-5, with isosteric heat of adsorption of about 34 kJ/mol. Diffusion coefficient of CO{sub 2} in the MOF-5 is in the range of 8.1-11.5 x 10{sup -9} cm{sup 2}/s in 295-331K with activation energy of 7.61 kJ/mol. MOF-5 offers attractive adsorption properties as an adsorbent for separation of CO{sub 2} from flue gas.

01 COAL, LIGNITE, AND PEAT↗

Corrosion behavior of carbon steel in the monoethanolamine-H{sub 2}O-CO{sub 2}-O{sub 2}-SO{sub 2} system

The effects of operating parameters on the corrosion of carbon steel in the monoethanolamine (MEA)-H{sub 2}O-CO{sub 2}-O{sub 2}-SO{sub 2} system were investigated using two different corrosion measurement techniques. The corrosion studies were conducted using a 273A potentiostat using MEA, O{sub 2}, and SO{sub 2} concentrations and CO{sub 2} loading in the ranges of 1-7 kmol/m{sup 3}, 0-100%, 0-204 ppm, and 0-0.5 mol CO{sub 2}/mol MEA, respectively, at corrosion temperatures in the range of 303-353 K. The experimental results showed, for the first time, that a higher concentration of SO{sub 2} in a simulated flue gas stream induces a higher corrosion rate essentially because of the increase in the hydrogen ion concentration generated by reactions of SO{sub 2} and H{sub 2}O as well as SO{sub 2}, O{sub 2}, and H{sub 2}O. Also, an increase in oxygen concentration in the simulated flue gas stream causes a higher corrosion rate due to the increasing solubility of oxygen and, in turn, a higher amount of dissolved oxygen in the liquid phase. The results further show that an increase in the concentrations of MEA, O{sub 2}, and SO{sub 2} as well as CO{sub 2} loading will cause the generation of higher amounts of hydrogen or hydronium ions, as well as carbonic acid and bicarbonate ions, and this is what leads to a higher corrosion rate.

01 COAL, LIGNITE, AND PEAT↗

Corrosion behavior of carbon steel in the monoethanolamine-H{sub 2}O-CO{sub 2}-O{sub 2}-SO{sub 2} System: products, reaction pathways, and kinetics

This work investigates the effect of operating parameters on corrosion products, reaction pathways, and kinetics For the corrosion of carbon steel in the monoethanolamine-H{sub 2}O-CO{sub 2}-O{sub 2}-SO{sub 2} system. Corrosion experiments were conducted using a 273A potentiostat unit under conditions in which monoethanolamine (MEA), O{sub 2}, and SO{sub 2} concentrations and CO{sub 2} loading were in the range of 1-7 kmol/m{sup 3}, 0-100%, 0-204 ppm, and 0-0.5 mol CO{sub 2}/mol MEA, respectively, at corrosion temperatures of 303-353 K to mimic the absorption-regeneration sections. Analysis, performed for this system for the first time, shows that corrosion products generated from the effect of SO{sub 2} include FeSO{sub 4} and Fe{sub 2}O{sub 3} {center_dot} H{sub 2}O. Also, a higher concentration of SO{sub 2} in simulated flue gas stream induces a higher corrosion rate because of the increase in the hydrogen ion concentration generated by reactions of SO{sub 2} and H{sub 2}O as well as SO{sub 2}, O{sub 2}, and H{sub 2}O. A power-law model developed to correlate corrosion rate with the parameters in the MEA-H{sub 2}O-CO{sub 2}-O{sub 2}-SO{sub 2} system shows that corrosion rate of carbon steel increases with an increase in O{sub 2} and SO{sub 2} concentrations in simulated flue gas stream, as well as MEA concentration, CO{sub 2} loading, and operating temperature. It was observed that CO{sub 2} loading had the highest impact on the corrosion rate, while SO{sub 2} and O{sub 2} show only slight effects on the corrosion rate.

01 COAL, LIGNITE, AND PEAT↗

Comparison of mercury retention by fly ashes using different experimental devices

To study mercury (Hg) retention in solid sorbents, researchers generally employ similar laboratory-scale devices. However, despite their similarities, these devices are generally used under different experimental conditions. The Hg concentration in the gas phase, gas flow, and sorbent-bed characteristics are variables that influence the contact time, mass transfer, and kinetics and may greatly modify the quantities of Hg retained when the same sorbents are compared. These differences in the experimental conditions do not impede an evaluation of the sorbents as long as the results obtained points toward the same qualitative conclusions. However, the extent of variation needs to be defined to avoid misinterpretation. To illustrate the range of interpretations, the results of a preliminary approach using four experimental devices in two laboratories have been compared in this work. All the experiments were carried out under a nitrogen atmosphere and Hg{sup 0} in the gas phase. The same sorbents were employed in all the devices. These were fly ashes obtained from the combustion of coals of different rank and with different unburned carbon contents. From the results obtained it can be inferred that it is necessary to strictly control the influence of the experimental variables to infer a correct interpretation of the results.

01 COAL, LIGNITE, AND PEAT↗

Effects of H{sub 2}O and particles on the simultaneous removal of SO{sub 2} and fly ash using a fluidized-bed sorbent/catalyst reactor

This study investigated the potential of a fluidized-bed sorbent/catalyst reactor for the simultaneous removals of SO{sub 2} and fly ash from a simulated flue gas containing different H{sub 2}O and particles. Experimental results showed that the removal efficiency of particles and SO{sub 2} was 85%-96% and 5.75-2.97 mg SO{sub 2}/g, respectively, as the H{sub 2}O content was 1.5-5.3%. The activities of sorbent/catalysts for simultaneous removals of SO{sub 2} and particles were inhibited by H{sub 2}O and particles, and the inhibition effects increased with the content of H{sub 2}O. As the H{sub 2}O content increased, the particle size distribution (PSD) of fine particles shifted to the coarse particles. The results of BET analysis show that the obstruction phenomenon of the sorbent/catalyst caused by the particles was diminished with the increased content of H{sub 2}O. The results showed this aggregation phenomenon of fine particles shifted to the coarse particles may cause increased water vapor content in fluidized-bed sorbent/catalyst reactor.

01 COAL, LIGNITE, AND PEAT↗

Computational fluid dynamics study of pulverized coal combustion in blast furnace raceway

In this work, a numerical model is used to study the flow and coal combustion along the coal plume in a large-scale setting simulating the lance-blowpipe-tuyere-raceway region of a blast furnace. The model formulation is validated against the measurements in terms of burnout for both low and high volatile coals. The typical phenomena related to coal combustion along the coal plume are simulated and analyzed. The effects of some operational parameters on combustion behavior are also investigated. The results indicate that oxygen as a cooling gas gives a higher coal burnout than methane and air. The underlying mechanism of coal combustion is explored. It is shown that under the conditions examined, coal burnout strongly depends on the availability of oxygen and residence time. Moreover, the influences of two related issues, i.e. the treatment of volatile matter (VM) and geometric setting in modeling, are investigated. The results show that the predictions of final burnouts using three different VM treatments are just slightly different, but all comparable to the measurements. However, the influence of the geometric setting is not negligible when numerically examining the combustion of pulverized coal under blast furnace conditions.

01 COAL, LIGNITE, AND PEAT↗

Multistage fluidized bed reactor performance characterization for adsorption of carbon dioxide

Carbon dioxide and its different compounds are generated as primary greenhouse gases from the flue gases of coal-fired thermal power plants, boilers, and other stationary combustion processes. This greenhouse gas causes global warming after being emitted to the environment. To deal with this problem, a new dry scrubbing process was tested in this study. A three-stage countercurrent fluidized bed adsorber was developed, designed, and fabricated. It was used as a removal apparatus and operated in a continuous regime for the two-phase system. The height of each stage was 0.30 m, and the inner diameter was 0.10 m. The paper presents the removal of CO{sub 2} from gas mixtures by chemical sorption on porous granular calcium oxide particles in the reactor at ambient temperature. The advantages of a multistage fluidized bed reactor for high mass transfer and high gas-solid contact can enhance the removal of the gas when using a dry method. The effects of the operating parameters such as sorbent, superficial gas velocity, and the Weir height on CO{sub 2} removal efficiency in the multistage fluidized bed were investigated. The results indicate that the removal efficiency of the carbon dioxide was around 71% at a high solid flow rate corresponding to lower gas velocity at room temperature. In comparison with wet scrubbers, this dry process appears to have lower cost, less complicated configuration, and simpler disposal of used sorbent. The results in this study assume importance from the perspective of use of a multistage fluidized bed adsorber for control of gaseous pollutants at high temperature.

01 COAL, LIGNITE, AND PEAT↗

Long-term behavior of CaO-based pellets supported by calcium aluminate cements in a long series of CO{sub 2} capture cycles

A series of carbonation/calcination tests consisting of 1000 cycles was performed with CaO-based pellets prepared using hydrated lime and calcium aluminate cement. The change in CO{sub 2} carrying capacity of the sorbent was investigated in a thermogravimetric analyzer (TGA) apparatus and the morphology of residues after those cycles in the TGA was examined by scanning electron microscopy (SEM). Larger quantities of sorbent pellets underwent 300 carbonation/calcination cycles in a tube furnace (TF), and their properties were examined by nitrogen physisorption tests (BET and BJH). The crushing strength of the pellets before and after the CO{sub 2} cycles was determined by means of a custom-made strength testing apparatus. The results showed high CO{sub 2} carrying capacity in long series of cycles with an extremely high residual activity of the order of 28%. This superior performance is a result of favorable morphology due to the existence of large numbers of nanosized pores suitable for carbonation. This morphology is relatively stable during cycles due to the presence of mayenite (Ca{sub 12}Al{sub 14}O{sub 33}) in the CaO structure. However, the crushing tests showed that pellets lost strength after 300 carbonation/calcination cycles, and this appears to be due to the cracks formed in the pellets. This effect was not observed in smaller particles suitable for use in fluidized bed (FBC) systems.

01 COAL, LIGNITE, AND PEAT↗

Magnesia-stabilized calcium oxide absorbents with improved durability for high temperature CO{sub 2} capture

Calcium oxide based materials are attractive regenerable absorbents for separating CO{sub 2} from hot gas streams because of their high reactivity, high CO{sub 2} capacity, and low material cost. Their high carbonation temperature makes it possible to recover and use high quality heat released during CO{sub 2} capture, which increases overall process efficiency. However, the performance of all reported CaO-based absorbents deteriorates as the number of carbonation-decarbonation cycles increases. This is caused by absorbent sintering during the highly exothermic carbonation process. We have found that sintering can be effectively mitigated by properly mixing with a modest amount of MgO. A class of CaO-based absorbents with improved durability and CO{sub 2} reactivity were prepared by physical mixing of Ca(CH{sub 3}COO){sub 2} with small MgO particles followed by high temperature calcination. With 26 wt % MgO content, a CaO-MgO mixture prepared by this method gives as high as 53 wt % CO{sub 2} capacity after 50 carbonation-decarbonation cycles at 758{sup o}C. Without MgO addition, the CO{sub 2} capacity of pure CaO obtained from the same source decreases from 66 wt % for the first cycle to 26 wt % for the 50th cycle under the same test conditions.

01 COAL, LIGNITE, AND PEAT↗

Glass-based processing of mixed-oxide desulfurization sorbents

The favorable thermodynamics of the reaction between H{sub 2}S and oxides of iron, nickel, and zinc make these materials suitable for the sorption of sulfur from coal-derived synthesis gas. As an alternative to traditional solid-state processing, the suitability for coal gas desulfurization of glass-ceramics based on transition metal oxides has been evaluated. Glass-ceramics based on NiAl2O{sub 4} and ZnFe2O{sub 4} have similar sorption properties and a high resistance to agglomeration, but the inexpensive raw materials and moderate processing temperature of the ZnFe2O{sub 4}-based glass makes it more suitable for a commercial application. The overall performance is highly dependent on the particle size of the sorbent, but these materials can be formed with relatively high surface areas by using fiber-based processing. This material is a potential alternative to mixed oxide sorbents prepared by solid-state processing, as it offers comparable performance combined with the ability to process the glass by existing glass-processing techniques.

01 COAL, LIGNITE, AND PEAT↗

Modeling of multiphase flow and heat transfer in radiant syngas cooler of an entrained-flow coal gasification

A comprehensive model has been developed to analyze the multiphase flow and heat transfer in the radiant syngas cooler (RSC) of an industrial-scale entrained-flow coal gasification. The three-dimensional multiphase flow field and temperature field were reconstructed. The realizable {kappa}-{epsilon} turbulence model is applied to calculate the gas flow field, while the discrete random walk model is applied to trace the particles, and the interaction between the gas and the particle is considered using a two-way coupling model. The radiative properties of syngas mixture are calculated by weighted-sum-of-gray-gases model (WSGGM). The Ranz-Marshall correlation for the Nusselt number is used to account for convection heat transfer between the gas phase and the particles. The discrete ordinate model is applied to model the radiative heat transfer, and the effect of ash/slag particles on radiative heat transfer is considered. The model was successfully validated by comparison with the industrial plant measurement data, which demonstrated the ability of the model to optimize the design. The results show that a torch shape inlet jet was formed in the RSC, and its length increased with the diameter of the central channel. The recirculation zones appeared around the inlet jet, top, and bottom of the RSC. The overall temperature decreased with the heat-transfer surface area of the fins. The concentration distribution, velocity distribution, residence time distribution, and temperature distribution of particles with different diameters have been discussed. Finally, the slag/ash particles size distribution and temperature profile at the bottom of the RSC have been presented.

01 COAL, LIGNITE, AND PEAT↗

Dramatic tuning of carbon dioxide uptake via metal substitution in a coordination polymer with cylindrical pores

A series of four isostructural microporous coordination polymers (MCPs) differing in metal composition is demonstrated to exhibit exceptional uptake of CO{sub 2} at low pressures and ambient temperature. These conditions are particularly relevant for capture of flue gas from coal-fired power plants. A magnesium-based material is presented that is the highest surface area magnesium MCP yet reported and displays ultrahigh affinity based on heat of adsorption for CO{sub 2}. This study demonstrates that physisorptive materials can achieve affinities and capacities competitive with amine sorbents while greatly reducing the energy cost associated with regeneration.

01 COAL, LIGNITE, AND PEAT↗

Amine-functionalized task-specific ionic liquids: a mechanistic explanation for the dramatic increase in viscosity upon complexation with CO{sub 2} from molecular simulation

The capture of CO{sub 2} from fossil fuel combustion, particularly in coal-fired power plants, represents a critical component of efforts aimed at stabilizing greenhouse gas levels in the atmosphere. Recently, a series of second-generation task-specific ionic liquids (TSILs) containing amine functional groups have been synthesized and demonstrated to have much higher capacities for CO{sub 2} due to their reactivity with CO{sub 2}, as well unusually high viscosities in both the neat and complexed states. The current work extends the seminal studies of CO{sub 2} capture with ionic liquids (ILs) by providing insight from simulations into the mechanism responsible for the dramatic increase in viscosity upon complexation. Simulations conclusively demonstrate that the slow translational and rotational dynamics, which are manifest in the high viscosity, may be attributable to the formation of a strong, pervasive hydrogen-bonded network. Semiquantitative estimates of the cation and anion self-diffusion coefficients and rotational time constants, as well as detailed hydrogen bond analysis, are consistent with the experimentally observed formation of glassy or gel-like materials upon contact with CO{sub 2}. This has significant implications for the design of new approaches or materials involving ILs that take advantage of these preconceived limitations, in the synthesis or manipulation of new TSIL frameworks for CO{sub 2} capture, and in novel experimental studies of chemistries and dynamics in persistent heterogeneous environments.

01 COAL, LIGNITE, AND PEAT↗

'Molecular Basket' sorbents for separation of CO{sub 2} and H{sub 2}S from various gas streams

A new generation of 'molecular basket' sorbents (MBS) has been developed by the optimum combination of the nanoporous material and CO{sub 2}/H{sub 2}S-philic polymer sorbent to increase the accessible sorption sites for CO{sub 2} capture from flue gas (Postdecarbonization), and for CO{sub 2} and H{sub 2}S separation from the reduced gases, such as synthesis gas, reformate (Predecarbonization), natural gas, coal/biomass gasification gas, and biogas. The sorption capacity of 140 mg of CO{sub 2}/g of sorb was achieved at 15 kPa CO{sub 2} partial pressure, which shows superior performance in comparison with other known sorbents. In addition, an exceptional dependence of MBS sorption performance on temperature for CO{sub 2} and H{sub 2}S was found and discussed at a molecular level via the computational chemistry approach. On the basis of the fundamental understanding of MBS sorption characteristics, an innovative sorption process was proposed and demonstrated at the laboratory scale for removing and recovering CO{sub 2} and H{sub 2}S, respectively, from a model gas. The present study provides a new approach for development of the novel CO{sub 2}/H{sub 2}S sorbents and may have a major impact on the advance of science and technology for CO{sub 2}/H{sub 2}S capture and separation from various gases.

01 COAL, LIGNITE, AND PEAT↗

Strong CO{sub 2} binding in a water-stable, triazolate-bridged metal-organic framework functionalized with ethylenediamine

Reaction of CuCl{sub 2}{center_dot}2H{sub 2}O with 1,3,5-tris(1H-1,2,3-triazol-5-yl)benzene (H{sub 3}BTTri) in DMF at 100{sup o}C generates the metal-organic framework H{sub 3}((Cu{sub 4}Cl){sub 3}(BTTri){sub 8}(DMF){sub 12}){center_dot}7DMF {center_dot} 76H{sub 2}O(1-DMF). The sodalite-type structure of the framework consists of BTTri{sup 3-}-linked (Cu{sub 4}Cl){sup 7+} square clusters in which each Cu-II center has a terminal DMF Ligand directed toward the interior of a large pore. The framework exhibits a high thermal stability of up to 270{sup o}C, as well as exceptional chemical stability in air, boiling water, and acidic media. Following exchange of the guest solvent and bound DMF molecules for methanol to give 1-MeOH, complete desolvation of the framework at 180 degrees C generated H{sub 3}(Cu{sub 4}Cl{sub 3}(BTTri){sub 8}) (1) with exposed Cu-II sites on its surface. Following a previously reported protocol, ethylenediamine molecules were grafted onto these sites to afford 1-en, featuring terminal alkylamine groups. The N{sub 2} adsorption isotherms indicate a reduction in the BET surface area from 1770 to 345 m{sup 2}/g following grafting. The H{sub 2} adsorption data at 77 K for 1 indicate a fully reversible uptake of 1.2 wt % at 1.2 bar, while the CO{sub 2} isotherm at 195 K shows a maximal uptake of 90 wt % at 1 bar. Compared to 1, the alkylamine-functionalized framework I-en exhibits a higher uptake of CO{sub 2} at 298 K and pressures up to ca. 0.1 bar, as well as a higher CO{sub 2}/N{sub 2} selectivity at all measured pressures. Significantly, 1-en also exhibits an isosteric heat of CO{sub 2} adsorption of 90 kJ/mol, which is much higher than the 21 kJ/mol observed for 1. This chemisorption interaction is the strongest reported to date for a metal-organic framework and points toward the potential utility of alkylamine-appended frameworks for the postcombustion capture of CO{sub 2} from low-pressure flue gas streams.

01 COAL, LIGNITE, AND PEAT↗

Solubility of carbon dioxide in an aqueous blend of diethanolamine and piperazine

The solubility of CO{sub 2} in aqueous blends of diethanolamine (DEA) and piperazine (PZ), from mixtures of CO{sub 2} and N{sub 2}, was measured for temperatures and CO{sub 2} partial pressures ranging from (303.14 to 353.14) K and (10.133 to 20.265) kPa, respectively. Measurements were made by a saturation method using a laboratory scale bubble column. The results of CO{sub 2} solubility in liquid are expressed as {alpha}(CO{sub 2}) (mol CO{sub 2}/mol amine) for all experimental runs. A solubility model is developed to correlate and predict the solubility data of CO{sub 2} in aqueous blends of DEA and PZ. There is all acceptable degree of agreement between the experimental data of the present study and predictions of the solubility model with an average absolute deviation of less than 4.5%.

01 COAL, LIGNITE, AND PEAT↗

Kinetically Relevant Steps and H2/D2 Isotope Effects in Fischer-Tropsch Synthesis on Fe and Co Catalysts

H2/D2 isotope effects on Fischer-Tropsch synthesis (FTS) rate and selectivity are examined here by combining measured values on Fe and Co at conditions leading to high C5+ yields with theoretical estimates on model Fe(110) and Co(0001) surfaces with high coverages of chemisorbed CO (CO*). Inverse isotope effects (rH/rD < 1) are observed on Co and Fe catalysts as a result of compensating thermodynamic (H2 dissociation to H*; H* addition to CO* species to form HCO*) and kinetic (H* reaction with HCO*) isotope effects. These isotopic effects and their rigorous mechanistic interpretation confirm the prevalence of H-assisted CO dissociation routes on both Fe and Co catalysts, instead of unassisted pathways that would lead to similar rates with H2 and D2 reactants. The small contributions from unassisted pathways to CO conversion rates on Fe are indeed independent of the dihydrogen isotope, as is also the case for the rates of primary reactions that form CO2 as the sole oxygen rejection route in unassisted CO dissociation paths. Isotopic effects on the selectivity to C5+ and CH4 products are small, and D2 leads to a more paraffinic product than does H2, apparently because it leads to preference for chain termination via hydrogen addition over abstraction. These results are consistent with FTS pathways limited by H-assisted CO dissociation on both Fe and Co and illustrate the importance of thermodynamic contributions to inverse isotope effects for reactions involving quasi-equilibrated H2 dissociation and the subsequent addition of H* in hydrogenation catalysis, as illustrated here by theory and experiment for the specific case of CO hydrogenation.

01 COAL, LIGNITE, AND PEAT↗