Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LEDs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Understanding the Deformation Mechanisms of FeNiMnAlCr High Entropy Alloys

The aim of this project was to understand the microstructure and mechanical properties of Fe-Ni-Mn-Al-Cr high entropy alloys. High entropy alloys are defined as materials containing five or more elements with each element constituting 5-35 atomic percent of the alloy. We performed several different tasks in this project. 1) We showed that reducing the crystal or grain size in single-phase Fe40Ni11Mn35Al8Cr6 containing either 1.1 atomic percent carbon added or with no carbon added produced a substantial increase in strength with a small reduction in ductility. The finer grain size material was produced by cold rolling followed by heating to recrystallize the microstructure. The changes in strength and ductility were related to observed changes in deformation structure as determined by transmission electron microscopy. We also examined how the deformation behavior changed with temperature from -200°C to 200°C. 2) We showed that heating Fe36Ni18Mn33Al13 with and without 1.26 at.% carbon led to ordered body-centered cubic precipitates forming in the materials, which were both initially two-phase. The heat treatment again led to substantial increases in strength with some reduction in ductility. 3) We examined whether titanium additions (2 atomic percent) to Fe42Ni18Mn33Al13 could improve the mechanical properties. We examined both as-cast material and material that had been recrystallized to produce a fine grain size. In both cases ordered body-centered cubic precipitates were present. Again, the recrystallization and resulting reduction in grain size increased the yield strength and reduced the ductility. We also showed, using high-resolution electron microscopy, that contrary to some predictions, having an alloy containing a range of atoms with different atomic diameters produced no lattice distortions. 4) We used scanning electron microscopy and transmission electron microscopy coupled with energy dispersive x-ray spectroscopy to show that carbides formed during intermediate temperature (≤800oC) heating of carbon-doped Fe40Ni11Mn35Al8Cr6. In addition to forming within the grains, the carbides coated the grain boundaries. This produced an increase in strength but a drastic reduction in ductility. However, we showed by hot rolling we could get both high strength and high ductility for this material. The work led to nine publications in referred journals and contributed to the education of two Ph.D. students. In addition, ten presentations (six of which were invited) at conferences, at a university and at a national laboratory in Germany.

36 MATERIALS SCIENCE↗

20 Channel Quench Detector

A multi-channel quench detector is useful for troubleshooting of prototype HTC superconducting magnets with current lead connections and imbedded splices. There are commercially available quench detectors, but not with as many channels, or with the particular functionality of this unit. This unit was designed specifically for cold testing of a superconducting sextupole prototype, which is wound with many turns of HTC ribbon. Associated with the current lead connections and the imbedded splices are 18 voltage taps, thus 17 quench detection channels are required to monitor the condition of the magnet. Of the 20 differential input channels in this quench detection unit, 19 are configured in a ladder network. The 20th channel is isolated and can be connected across any pair of voltage taps. This quench detector is designed to be used to monitor the condition of a series-connected superconducting magnet powered by a unipolar supply, and therefore the polarity and sequence of the voltage taps must be observed. There are 20 toggle switches and 20 red LEDs on the front panel of the unit which are associated with the 20 quench detection channels. There are also 2 green LEDs to indicate the state of the +5 V and +25 V internal supplies. Channel input impedance is ~10 kΩ. The input lines are diode protected against negative voltage transients and can tolerate up to +25 V, which is greater than the compliance of supplies typically used to power superconducting magnets. The front panel switches are used to enable or disable individual channels. If a channel is not used it is disabled. There are 20 pots on the quench detector PCB. They provide adjustment for the sensitivity of each of the 20 channels. There is an onboard reference to facilitate channel sensitivity calibration. The detection sensitivity range is from ~27 mV to ~700 mV. Typically all channels are set for the same sensitivity. The response time is ~20 μs, but the time constant can be increased if desired by adding a single capacitor to each channel. When the magnet under test is cooled to the superconducting state and the supply current to the windings is slowly ramped up to the set point, if there is a voltage rise across a pair of voltage taps which exceeds the quench detection limit of a given channel, then the front panel LED for that channel illuminates and all other channels are disabled within ~25 ns. Thus only the first quench is detected for the channels which are enabled. A pushbutton switch on the front panel is used to reset a quench detection. A 25 pin D-subminiature connector on the back of the unit is used for the channel inputs. TTL level ‘quench’ and ‘quench-not’ signals, and DPDT relay contacts, are provided through a 9 pin D-subminiature connector on the back to indicate a detected quench condition, which could be used to disable the power supply and engage an energy absorber.

47 OTHER INSTRUMENTATION↗

FY18 LLNL Experimental Programs at Omega

In Fiscal Year 2018 (FY18), Lawrence Livermore National Laboratory’s (LLNL’s) High Energy-Density Physics (HED) and Indirect Drive Inertial Confinement Fusion (ICF-ID) programs conducted numerous campaigns on the OMEGA and OMEGA-EP (EP) laser systems. This was the 20th year of National Lab collaborative experiments at OMEGA since the Nova Laser at LLNL shut down in 1999 [1], building upon prior collaborations. In FY18 overall, these LLNL programs led 465 target shots, with 283 shots using just the OMEGA laser system, 172 shots using just the EP laser system, and 10 Joint shots using both lasers together. Approximately 28% of the total number of shots (60 OMEGA shots and 71 EP shots) supported the Indirect Drive Inertial Confinement Fusion Campaign. The remaining 72% (223 OMEGA-only shots, 101 EP-only shots and 10 Joint shots) were dedicated to experiments for High-Energy-Density Physics. Highlights of the various HED and ICF-ID campaigns are summarized in the following reports. In addition to these experiments, LLNL Principal Investigators (PIs) led a variety of Laboratory Basic Science campaigns using OMEGA and EP, including 99 target shots using just OMEGA and 39 shots using just EP. The highlights of these are also summarized, following the ICF and HED campaigns. Overall, LLNL PIs led a total of 603 shots at LLE in FY 2018. In addition, LLNL PIs supported 47 NLUF shots on Omega and 31 NLUF shots on EP in collaboration with the academic community.

36 MATERIALS SCIENCE↗

Energy Cost Savings of Systems-Based Building Retrofits: A Study of Three Integrated Lighting Systems in Comparison with Component Based Retrofits

Most building retrofit projects are still component-based in that they typically address only one piece or type of equipment at a time. Systems-based retrofits that seek to address multiple components in an integrated manner have the potential to provide significantly greater energy savings. Lawrence Berkeley National Laboratory (LBNL) partnered with several utilities to develop and evaluate three different integrated retrofit packages involving lighting systems: automated shading with daylight dimming controls, workstation-specific lighting with daylight controls, and task/ambient lighting with plug load occupancy controls. Specifically, our analysis sought to quantify the marginal benefits of these systems (energy savings as well as lighting performance and visual comfort) relative to component based approaches. The analysis was based on a combination of measured performance data from LBNL’s FLEXLAB® test facility and energy simulations. All three systems were compared to a simple fluorescent-to-LED retrofit, which represents the component-based approach. While the simple LED upgrade provides significant lighting energy savings of 63%, the systems yielded energy savings of 81-93%, which equates to additional savings of 49-82% over the simple LED upgrade. All systems tested provided satisfactory visual comfort as well, indicating good potential for market acceptance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Jetting Response in Architected Structures

Architected structures are gaining prominence for structural applications as the additive manufacturing technologies that can enable such materials mature. With the expanded design space, such mesoscopic structures occupy the middle ground between random foams and bulk materials. Studies into the deformation response of such structures are limited, particularly under dynamic compression. Early studies indicate the presence of an elastic precursor wave running ahead of the compaction wave. Additional studies also have shown that jetting is known to occur under shock loading conditions due to the presence of geometric perturbations introduced in the long-range periodic structures. Given that starting point, the motivation for this research was to understand the origin of the observed jetting and extend our understanding of how this comes about across a broad spectrum of lattice types, material compositions, length scales, and dynamic loading conditions. The jetting behavior due to lattice structures was studied through a series of dynamic compression plate impact experiments with in-situ x-ray imaging. This work was enabled by the NNSA-funded Dynamic Compression Sector at the Advanced Photon Source, which is housed at Argonne National Laboratory. Prior studies, and also evident in this work, have shown that deformation mechanisms in architected structures are difficult to study using our traditional diagnostics, and the role of in situ observations in this regard cannot be overstated. The role of the impact conditions, the lattice spacing, the lattice architecture, and the lattice base material was explored in the context of promoting or suppressing jet formation. A transition from latticeled to impactor-led jetting is observed above a certain impact threshold. Complementary direct numerical simulations (DNS) were also performed to compare with the experiments, study the underlying stress state giving rise to jetting, and provide insight for conditions not studied experimentally. Such simulations suggest certain trends for promoting or suppressing jetting akin to traditional Richtmyer-Meshkov instability studies. We present a geometric argument to explain the competitive process leading to lattice and/or impactor jetting which incorporates base material properties, the periodicity of the lattice, and basic tunable length scales of the lattice. Our results are consistent with previous observations on such lattices. Expanding on that work, the emergence of a transition of the jet material composition must depends solely on the base material properties and the geometric arrangement of the lattice structure. The fact that we have obtained reasonable qualitative and quantitative agreement regarding the jet formation and propagation behavior leads us to trust the underlying materials models. We can speculate that this and potentially other emergent phenomena might also be possible from a unique combination of base material properties and geometric arrangement of lattice structures. While the transition from polymer-led to flyer-led jetting might seem counterintuitive at first, it is a natural extension of the impact conditions and the arrangement of the materials. Better understanding of how the base material properties are coupled to the lattice structure to give rise to such phenomena will likely improve design for such structures under dynamic compression conditions. As such, the direct numerical simulations provide a pathway to design of architectures in future applications.

36 MATERIALS SCIENCE↗

Connected Lighting Systems Efficiency Study: PoE Cable Energy Losses, Part 2

Power over Ethernet (PoE) technology offers the ability to provide both low-voltage direct current (DC) power and communication over a standard Ethernet cable—also referred to as a local area network (LAN) cable or Category cable. Light-emitting diode (LED) technology has reduced the power required for lighting applications, while advances in PoE standards and technology have yielded substantial increases in the amount of power that can be delivered to a networked device over a single cable. As a result, PoE technology is emerging in lighting and many other applications beyond its historical foothold in telephony and networking equipment. Several major LED luminaire manufacturers have introduced PoE connected lighting systems in recent years, making this a potentially disruptive technology. PoE lighting systems can offer improved efficiency relative to traditional line voltage alternating current (AC) systems, because AC-DC power conversion losses can be reduced if this work is consolidated among one or more PoE switches, rather than being distributed among a greater number of smaller LED drivers. However, this effect can be offset to some extent by increased losses associated with an increased voltage drop in the low-voltage Ethernet cabling. In fact, these losses could exceed 15% in poorly designed systems. Aspects of cable design that can affect cable energy performance include American Wire Gauge (AWG), Category (e.g., 5e), shielding, and fire rating (e.g., CMP). Installation practices (e.g., bending, bundling, conduit) can also affect cable performance. Although cable energy losses can be predicted with knowledge of conductor DC resistance (DCR), and DCR can be estimated based on rated AWG, most product datasheets state maximum DCR - or reference standards that specify DCR limits - in lieu of nominal DCR.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Response of GaN-Based Semiconductor Devices to Ion and Gamma Irradiation

GaN has electronic properties that make it an excellent material for the next generation of power electronics; however, its radiation hardening still needs further understanding before it is used in radiation environments. In this work we explored the response of commercial InGaN LEDs to two different radiation environments: ion and gamma irradiations. For ion irradiations we performed two types of irradiations at the Ion Beam Lab (IBL) at Sandia National Laboratories (SNL): high energy and end of range (EOR) irradiations. For gamma irradiations we fielded devices at the gamma irradiation facility (GIF) at SNL. The response of the LEDs to radiation was investigated by IV, light output and light output vs frequency measurements. We found that dose levels up to 500 krads do not degrade the electrical properties of the devices and that devices exposed to ion irradiations exhibit a linear and non- linear dependence with fluence for two different ranges of fluence levels. We also performed current injection annealing studies to explore the annealing properties of InGaN LEDs.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

MOCVD Growth and Characterization of ZnSnN 2

Since the first few reports of its synthesis in 2011 and 20121-3, interest in ZnSnN 2 for diverse applications, including photovoltaics1,3,4, visible light photocatalysis5, and optoelectronics, has been growing. Novel nitride-based LED device designs promise high gains in efficiency at emission wavelengths into the green, amber and even red.6-8 Their realization requires the precise insertion of an ultrathin layer of ZnGeN 2 or ZnSnN 2 into the active region of an InGaAs-GaAs LED structure. While thin films of ZnSnN 2 have been synthesized by RF sputtering1,9 and by MBE 2,10,11, and thin films of ZnGeN 2 , ZnSiN 2 and their alloys by MOCVD, the synthesis of ZnSnN 2 thin films by MOCVD has not yet been reported. It is a challenging goal, given the narrow temperature window between efficient activation of ammonia and the thermal decomposition of ZnSnN 2 at near-atmospheric pressures. We report here the results of studies of ZnSnN 2 films grown on r- and c-plane sapphire substrates, GaN templates on sapphire, and In 0.15 Ga 0.85 N templates on GaN-on-sapphire, at temperatures from 500 °C to 560 °C, using tetramethyltin (TMSn), diethylzinc (DEZn), germane and ammonia. Chamber pressures were varied between 200 and 500 torr. In addition, the ratios of the cation precursors and the total cation-to-anion precursor ratios were varied. Single crystal growth, as evidenced by 2θ-ω x-ray diffraction scans, was achieved on all of these substrates. Wurtzitic (0002) ZnSnN 2 diffraction were observed at 2θ ~ 32.90 for the samples grown on c-sapphire, GaN (0001) and InGaN (0001) templates, and wurtzitic (11-20) peak at 2θ ~ 54.80 for the films grown on r-sapphire. Higher pressures and higher temperatures promoted better crystallinity and more continuous films, as revealed by scanning electron microscopy (SEM) images and 2θ-ω x-ray diffraction peak widths and intensities. Crystal quality was observed to be highly dependent on growth temperature. For example, in one series a 10 °C change in growth temperature resulting in a factor of 15 increase in diffraction peak intensity. SEM images show that films grown on the GaN templates had better uniformity in nucleation than those grown on sapphire. The presence of satellite peaks around the Bragg peak in the XRD 2θ-ω scan for a film grown on a GaN template, and the absence of satellite peaks for the films grown simultaneously on c- and r-sapphire, also indicate superior quality for the film grown on GaN. HAADF-STEM images of films grown on these templates showed smooth interfaces at the film-substrate boundary and show growth rates as high as 167 nm/h, considerably higher than reported previously for MBE growth.9,10 Electron diffraction patterns show single crystallinity. Rocking curves show FWHM as low as 0.100. RMS surfaces roughnesses, measured by atomic force microscopy, are of the order of 3 nm for 1µm x 1µm areas. Current work is focusing on optimizing growth on InGaN templates. These templates are promising for their relatively lower lattice mismatch with ZnSnN 2 . Their use is a next step toward producing LED device structures.

Jayatunga, Benthara Hewage Dinushi↗

Gear Test Assembly - Report on Experimental Testing (FY2020)

The Gear Test Assembly (GTA) has completed Campaign #2 of in-sodium testing at the Mechanisms Engineering Test Loop (METL). Campaign #1 was conducted in 2019 and completed 19,600 cycles, correlating to 9,800 fuel assembly maneuvers. Campaign #1 was terminated following a shaft seizure caused by a failed bearing in the sodium gearbox. Campaign #2 was conducted in the spring of 2020 and completed 2,768 cycles, correlating to 1,384 fuel assembly maneuvers. Campaign #2 was terminated following elevated vibration measurements coming from the sodium gearbox. Following cleaning and disassembly, a bearing was found to have failed in the sodium gearbox. Campaign #1 used tapered roller bearings made of 52100 steel with a heat treatment from the manufacturer that allows for operation to 350°C. Campaign #2 used the same tapered roller bearings, but with no heat treatment. A new dynamic shaft seal design was used in Campaign #2 that led to significant reductions in argon consumption and graphite debris generation. A modified external gearbox system led to no external bearing failures and allowed for higher torque output. Finally, modifications to the Carbonation System led to a more effective carbonation process and all-around reduction in turnaround time.

42 ENGINEERING↗

U.S. Industrial and Commercial Motor System Market Assessment Report Volume 1: Characteristics of the Installed Base

Motor systems are an integral part of our industrial and commercial facilities. They provide the motive force behind the fans, pumps, compressors, chillers, and conveyors in these facilities. Given their centrality to any facility’s operations, they are a critical energy end use to understand, particularly when developing technologies and policies to meet sustainability goals, improve productivity, and enhance resilience. In the late 1990s, the U.S. Department of Energy (DOE) conducted two seminal studies to better understand the installed stock and energy savings opportunities of industrial and commercial motor systems. In the industrial sector, The United States Industrial Electric Motor Systems Market Opportunities Assessment used primary data collected through onsite assessments and led to a greater understanding of the installed base of motor systems, their characteristics, and the opportunities for energy savings (U.S. Department of Energy, 2002). Notable findings included the following: Industrial motor systems consumed 679 billion kilowatt-hours (kWh) in 1994, representing 23 percent of U.S. electricity consumption. Cost-effective energy efficiency measures could result in 62-104 billion kWh of energy savings annually. Sixty-two percent of the energy savings potential was from fan, pump, and compressor end use equipment. Nearly half of motor system electricity consumption was attributable to approximately 3,500 facilities, or 1.5 percent of U.S. manufacturing facilities. Opportunities for Energy Savings in the Residential and Commercial Sectors with High Efficiency Electric Motors provided an evaluation of the installed stock of motor driven equipment in U.S. commercial and residential buildings and opportunities for utilization of high efficiency motors and variable speed technologies (Arthur D. Little, 1999). Notable findings included the following: Commercial motor systems consumed 343 billion kWh in 1995, with refrigeration and space conditioning constituting 93 percent of the total. Cost-effective energy efficiency measures could result in 51 billion kWh of energy savings annually. Due in no small part to these seminal studies, motor system technologies and usage characteristics have changed drastically since the late 1990s. Greater awareness of cost-effective strategies for reducing motor system electricity consumption have been developed and deployed. This includes several software tools, literature, and utility and government programs promoting energy efficiency improvements in motor driven systems. Additionally, several rounds of energy efficiency standards have been enacted, resulting in improved installed motor efficiency. The cost of variable speed drives has dropped substantially, and combined with utility rebate programs, has led to their greater adoption. Further, since these results were published, the U.S. manufacturing sector has undergone a massive transformation. Due to global competition, some sectors have relocated operations overseas. Others have brought operations onshore to avail low cost and abundant natural gas. Additionally, automation and robotics have pervaded the entire sector. Consequently, these two reports likely do not represent the current state of motor driven systems in U.S. industrial and commercial facilities. As cited in recent studies, the lack of current information on motor system electricity consumption and use characteristics limits the ability to conduct analysis on energy savings potential, develop technologies to address energy and productivity gaps, and develop programs to promote energy efficiency practices and technologies for motor systems (International Energy Agency, 2007; UNIDO, 2010; McKane and Hasanbeigi, 2011; Waide and Brunner, 2011). Specifically, the lack of information affects a range of stakeholders: Governments must rely on outdated information when setting research agendas, developing policies, and designing energy efficiency programs and offerings. Utilities and energy efficiency programs cannot identify the current market needs or potential impact when designing rebate and energy efficiency programs. Electric grid planners cannot identify motor system usage characteristics when developing plans to support the resilience of the electric grid. Manufacturers of motors, motor driven equipment, and drives are hampered when developing technologies to meet the needs of their market. Motor system end users are limited in their ability to identify energy saving opportunities within their own facilities because they do not have reliable benchmark information. In response to the lack of current information and analysis on industrial and commercial motor systems, the DOE initiated an update to these two studies. Launched in 2016 and led by Lawrence Berkeley National Laboratory (LBNL), the Motor System Market Assessment (MSMA) provides an updated, more comprehensive assessment of the installed stock of motor systems in both the industrial and commercial sectors, a review of the supply chains supporting motor and drives in the U.S., and the performance improvement opportunity available from using best available technologies and maintenance and operation practices. The outcomes of the MSMA are documented in three U.S. Industrial and Commercial Motor System Market Assessment reports, with this report being the first listed: 1. Volume 1: Characteristics of the Installed Base (this report) documents the findings on the installed base of motor systems in the U.S. industrial and commercial sectors. Quantification of energy savings potential is not documented in this report but in Volume 3. 2. Volume 2: Motors and Drives Supply Chain Review reviews the state of supply chains for motors and drives installed in U.S. industrial and commercial facilities, focusing on advanced motor and drive technologies and their constituent materials. 3. Volume 3: Energy Savings Opportunity analyzes the energy performance improvement opportunity for the installed base of U.S. industrial and commercial motor systems. This report has been prepared as a reference for motor system stakeholders. It provides factual information as could be best determined by the assessment results and avoids speculating on any findings.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Laser Network US Experiments at the University of Texas at Austin

Under Subcontract B638654, The University of Texas at Austin (UT Austin) Center for High Energy Density Science supported three Laser Network US experiments and conducted upgrade planning for the Texas Petawatt Laser Facility. For the experiment “Investigation of the physics of MeV X-ray and particle generation using Compound Parabolic Concentrators” led by Dr. Andrew Mackinnon of Lawrence Livermore National Laboratory, UT Austin provided postdoctoral associate support in the person of Dr. Ganesh Tiwari. For the experiments “Megatesla magnetic fields and enhanced gamma-ray beam generation” led by Hans Rinderknecht of LLE, University of Rochester (experiment) and Alexey Arefiev of UC San Diego (theory) and “High resolution imaging of resonately accelerated electrons under tight focusing” led by Deepak Kumar of ELI-Beamlines, Czech Republic, UT Austin provided the Texas Petawatt Laser staff and a prorated share of the materials and supplies approximately equal to the average of those required for one 5-week experimental campaign. Summaries of these three experiments are provided in this report. Two staff members were hired—Dr. Sandra Bruce at 40% and Dr. Erhard Gaul at 50% time—to support Texas Petawatt Laser maintenance and operations and to plan for the Texas Relativistic Intensity Ultrafast Multi-beam Plasma Facility (TRIUMPF).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Influence of Communication on the Complexity of Connected Lighting Systems

Experience in the Next Generation Lighting Systems (NGLS) ”Living Lab” at the Parsons School of Design, has clearly shown the impacts of communication on the configuration complexity of the connected lighting systems installed there. Since 2017, NGLS has invited manufacturers to submit connected lighting systems for assessment against a set of specifications. To date, 14 systems of wirelessly connected LED luminaires and controls have been installed in classrooms with existing lighting. In nine of the rooms, new LED linear pendants or recessed troffers replaced existing luminaires; in the other rooms, LED “kits” were retrofitted into the existing troffers. Eleven of the installations featured sensors integrated in the luminaires or retrofit kits; the others used ceiling mounted sensors. All systems provided wall control devices for manual operation. For half of the installations, the complete systems were furnished by single companies; for the other half, luminaires and controls were furnished by separate companies. A total of 18 different companies provided products, with four of these located outside the United States including, Korea, Poland, Germany, and the Netherlands. In addition, two different electrical contractors in New York City provided multiple installation teams totaling 10 individuals, none of whom were familiar with any of the systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Optimized Carbon Fiber Intermediate Development to Enable High-Volume Manufacturing of Lightweight Automotive Composites

The ongoing pursuit of improved fuel economy and reduced greenhouse gas emissions has resulted in sustained interest for lightweight materials technologies. In this context, carbon fiber composites have captured the imagination of automotive engineers due to the potential to achieve substantial mass reduction when compared to traditional steel construction. That stated, the use of carbon fiber composites in automotive has been limited for the most part to premium supercars and other derivative platforms. In these cases, manufacturing costs are less of an obstacle to implementation, and the performance benefits of carbon fiber have enabled production of structures offering more than 50% weight savings. In practice, translating these low-volume demonstrations onto high-volume vehicle platforms has remained challenging. This can be attributed to several factors, with the absence of suitable high throughput production methodologies being a key impediment. To date, structural, crash critical components have relied upon manufacturing techniques born out of the aerospace industry. This has created a disconnect between automotive production systems that are accustomed to manufacturing multiple parts per minute and the aerospace technologies that have cycle times in the order of hours. Consequently, the focus of this project is the development of manufacturing process technology for carbon fiber composites that can support a mainstream vehicle program at an assumed throughput of 100,000 vehicles per year. In practice, this translates to a part-to-part cycle time of less than 3 minutes. Project participation included contributions from a broad range of academic, industrial and national lab partners. The primary scope of work, being the development of new carbon fiber epoxy compounds that are stable at room temperature and suited to high throughput automated processing. For project management, the work streams were divided into six key areas, with the lead organization in parentheses. • Carbon fiber/epoxy materials formulation development and scale up (Dow) • Simulation of discontinuous near isotropic meso-structure intermediates (Purdue) • Simulation of mechanical performance of compression molded components (Purdue) • Meso-Scale morphological analysis and correlation with structural performance (UTK) • Paint and adhesion durability analysis (MSU) • Demonstrator part design, prototype production, and validation testing (Ford). The primary goal at the commencement of the project was development of a chopped carbon fiber sheet molding compound (SMC) that offered a three times improvement in tensile modulus over a comparable glass-based SMC. In addition to meeting mechanical performance targets, the resin kinetics were modified to achieve a processing cycle time of less than 3 minutes. Other critical-to-quality (CTQ) specifications were also stipulated to account for a broad range of materials and processing characteristics. To achieve the above, staff scientists at Dow Chemical created an extensive series of new epoxy blends for testing and validation. Throughout this development, a key challenge was attaining material performance goals without impacting processing behavior and paintability of finished components. The latter required a new internal mold release system being developed by Dow that was designed to complement the kinetics of the rapid cure epoxy. As a complement to work studies at the industrial partners, the teams from academia executed a series of analytical and experimental studies to investigate potential factors influencing CF-SMC performance. Unit cell models were developed to capture the meso-scale representations of the fiber matrix architecture. Results of this analysis and subsequent morphological investigations led to the design of a novel composite derivative comprising carbon fiber platelets embedded in an epoxy matrix; the platelet size and aspect ratio playing significant role in final composite properties. This approach was a departure from previous research in CF-SMC development whereby bulk filamentization or disassembly of the carbon fiber rovings had been considered the most effective means of achieving both fiber wet through and wet-out. As the course of the academia studies progressed, the aspect ratio of the fiber constituents was further optimized before finalizing material attributes and processing conditions. For the purposes of technology validation, the Ford team led a work stream devoted to the design, fabrication and testing of demonstration components. The carbon fiber SMC material has the potential to displace numerous stampings and castings on an automotive structure but ultimately vehicle closure applications were selected to showcase the abilities of the CF-SMC to achieve both mass reduction and business case for large complex structures. Using target properties established by the Dow staff scientists, the complete closure system for a full-size sedan decklid and a mid-size wagon liftgate were engineered. Prototypes for both applications were fabricated using production representative processing methods to allow for physical testing and performance validation of the CF-SMC structures. Following completion of a testing program that concluded with a FMVSS301 55 mph offset rear crash, the CF-SMC formulation was declared by the Ford team to have met all engineering requirements. To summarize, the joint development activities during this project led to significant technical breakthroughs and achievement of all milestones. The result was the development of a novel, tack-free carbon fiber molding compound that is suited to automated processing. This combined room temperature stability, fast cure kinetics, and internal mold release system facilitates cycle times that are conducive to high-volume production. The VORAFUSE M6400 successfully passed technology validation at Ford and is now eligible for consideration on future production commercial vehicle programs.

36 MATERIALS SCIENCE↗

Foam Fracturing Study for Stimulation Development of Enhanced Geothermal Systems

The large thermal gradients and high subsurface temperatures of the western region of the U.S. hold great potential for the implementation of enhanced geothermal systems (EGS). The development of these potential EGS resources requires stimulation of the reservoir to enhance permeability and it has been widely reported that a substantial amount of water will be required should conventional hydraulic stimulation be used. This presents a huge challenge and a high risk to the geothermal development because the water stress1 in these areas is already high or extremely high. The use of foam, a gas/liquid mixture predominantly composed of gas, in fracturing is considered and explored in this project as a potential approach to address water concerns with hydraulic stimulation in the development of EGS. This project, led by Oak Ridge National Laboratory (ORNL) in collaboration with Temple University, was awarded in an open lab call in 2018, and was part of the DOE GTO waterless stimulation initiative. The goal of the project was to demonstrate the feasibility of foam fracturing for EGS development through two primary tasks: Task 1: Laboratory study of the effectiveness of foam fracturing for representative geological materials, including cyclic pressurization using foam (led by ORNL) and Task 2: High temperature foam material selection and characterization (led by Temple University). In FY19, ORNL finished the critical review on serval issues associated with foam fracturing and the implementation of the proposed tasks in a lab study (Wang, et al., 2019), and completed the foam fracturing testing using cement as a model material (Wang, et al, 2020a). The work at ORNL was geared up to develop a brand-new foam testing system in FY20. The purchase of main components for the new system was finished in the first half of the FY20. The assembly of the foam testing system and foam fracturing testing were completed in the second half of the FY20 (Wang, et al., 2021a). Task 1 required the development of a test system which can be used to perform hydraulic fracturing of geological specimens with both water and foamed liquids at pressure up to 6,000 psi (41.4 MPa). The system possesses several capabilities that conventional injection systems lack for hydraulic fracturing. In addition to its ability to generate foam with controlled quality, it is capable of cycling pressure levels between specified values up to frequencies of 50 Hz. The latter capability was developed to evaluate the hypothesis that cyclic loading of samples would produce enhanced fracturing. The system consists of two sections: one for foam generation and another for foam injection. The foam is generated through separate control and pressurization of liquid and gas phases with controlled flow rates. The injection section is equipped with a low-flow Coriolis flow that monitors the density of foam to ensure the injection is in the range of target foam quality2. Experimental results of foam fracturing are reported for cylindrical granite specimens using water and aqueous N2 foam as the fracturing fluids. All experiments were performed for unconfined conditions. The effects of injection mode (i.e., monotonic vs cyclic pressurization) on breakdown pressure and failure response sample were investigated using water alone as a fracturing fluid and foams with a range of compositions. It was found that in the case of monotonic injection, the breakdown pressure of granite specimens tended to be slightly higher when fracturing with foam. Additionally, with a foam quality of 90%, the water use can be reduced by 50 to 84%, depending on hole size. On the other hand, it was observed that the breakdown pressure can be brought down to 70% of the monotonic breakdown pressure by using low cycle fatigue. Finally, discussions are presented regarding injectivity and water use reduction.

15 GEOTHERMAL ENERGY↗

The Effect of Rolling As-Cast and Homogenized U-10Mo Samples on the Microstructure Development and Recovery Curves

Over the past several years Pacific Northwest National Laboratory (PNNL) has been actively involved in supporting the U.S. Department of Energy National Nuclear Security Administration Office of Material Management and Minimization (formerly Global Threat Reduction Initiative). The U.S. High-Power Research Reactor (USHPRR) project is developing alternatives to existing highly enriched uranium alloy fuel to reduce the proliferation threat. One option for a high-density metal fuel is uranium alloyed with 10 wt% molybdenum (U-10Mo). Forming the U-10Mo fuel plates/foils via rolling is an effective technique and is actively being pursued as part of the baseline manufacturing process. The processing of these fuel plates requires systematic investigation/understanding of the pre- and post-rolling microstructure, end-state mechanical properties, residual stresses, and defects, their effect on the mill during processing, and eventually, their in-reactor performance. In the work documented herein, studies were conducted to determine the effect of cold and hot rolling the as-cast and homogenized U-10Mo on its microstructure and hardness. The samples were homogenized at 900°C for 48 h, then later annealed for several durations and temperatures to investigate the effect on the material’s microstructure and hardness. The rolling of the as-cast plate, both hot and cold, was observed to form a molybdenum-rich and -lean banded structure. The cold rolling was ineffective, and in some cases exacerbated the as-cast defects. The grains elongated along the rolling direction and formed a pancake shape, while the carbides fractured perpendicularly to the rolling direction and left porosity between fractured particles of UC. The subsequent annealing of these samples at sub-eutectoid temperatures led to rapid precipitation of the α + γ ' lamellar phase, mainly in the molybdenum-lean regions. Annealing the samples above the eutectoid temperature did not refine the grain size or the banded microstructure. However, annealing the samples led to quick recovery in hardness as evidenced by a drop in Vickers hardness of 20%. Hot rolling was performed at 650 and 800°C. The hot-rolling mill loads (load separation force) were approximately 40 to 50% less than the cold-rolling for the same reduction and thickness. It was observed that hot rolling the samples with 50% or more reduction in thickness were responsible for dynamic recrystallization in the hot-rolled samples and led to grain refinement. Unlike the cold-rolled samples, the hot-rolled samples did not fracture the carbides and appeared to heal the casting defects. The recovery phenomenon was similar to the cold-rolled samples above the eutectoid temperatures, but owing to the refined grain size, the precipitation of the lamellar phase was far more rapid in these samples and the hardness increased more rapidly than in the cold rolled sample when heated below the eutectoid temperature. The data generated from these rolling efforts has been used to make the process modeling efforts more robust and applicable to all USHPRR partner rolling mills. The flow stress for cold rolling the samples was determined to be between 170-190 ksi, with frictional forces between 0.2 and 0.4 for the PNNL mill. The measured roll separation forces and those simulated using finite element methods for hot and cold rolling for the PNNL rolling mill were in good agreement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microbiome controls on harmful algal toxin production in Lake Erie (Final Project Report)

Lawrence Livermore National Laboratory (LLNL) funded this project with the aim to understand how the microbiome influences the toxicity of harmful algal blooms in Lake Erie. Dr. Xavier Mayali from LLNL led the project. Dr. Dragan Isailovic led University of Toledo portion of the project also involving Dr. Thomas Bridgeman, and Dr. Gregory Dick led the portion of the project at the University of Michigan with Dr. Jenan Kharbush.

54 ENVIRONMENTAL SCIENCES↗

Non-Equilibrium Synthesis of Semiconductor Alloys for Energy Applications

This project explores the synthesis under equilibrium/non-equilibrium conditions of semiconductor alloys critical to SSL to impose top-down influence on the formation of atomic-scale microstructures. A plasma-enhanced MOCVD (PE-MOCVD) technique is employed, in which plasma generated within the low-pressure reactor environment introduces additional energy that is delivered to the gas-phase reactants and growth surface, allowing relatively low substrate temperatures to be maintained, rapidly switching the crystal-growth environment into a non-equilibrium state. The project coordinates on-going work at National Renewable Energy Laboratory (NREL) that addresses order/disorder Al x In 1-x P (AlInP) confinement structures, which are predicted to surpass the power-conversion efficiency of current materials used for red/amber LEDs as components of so-called color-mixed LEDs, which integrate multiple LEDs in a single device for improved color rendering. Ordering, phase separation, and strain relaxation are central to this technology. During growth, each spontaneous process could be suppressed or enhanced on demand by application of plasma as an additional handle. This technique could have broader applications to other energy technologies, such as photovoltaics.

14 SOLAR ENERGY↗

Mitigating Traffic Congestion Through Visual Cues: Advancing Transportation Safety and Efficiency

While humans have an innate ability to estimate speed and distance, this capability is inherently imprecise. This imprecision has significant implications for traffic systems, which are highly sensitive to fluctuations in movement. Even small variations in velocity and following distances between travelers can create congestion in high-traffic environments. The absence of an effective and widely adopted solution creates significant transportation inefficiency. However, emerging technologies offer promising ways to help mitigate this issue. This paper will analyze the effectiveness of visual cues in reducing traffic congestion. Specifically, this paper presents an experiment using addressable LEDs to evaluate their effectiveness in influencing pedestrian behavior. These programmable lights enable individual control over each LED in a strip, allowing for dynamic lighting effects that serve as useful visual cues. The goal of this paper is to demonstrate that visual cues, such as addressable LED guidance, can effectively influence traveler behavior and contribute to reducing traffic congestion.

33 ADVANCED PROPULSION SYSTEMS↗