Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Grain Boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Erosion of aluminum 6061-T6 under cavitation attack in mineral oil and water

Studies of the erosion of aluminum 6061-T6 under cavitation attack in distilled water, ordinary tap water and a viscous mineral oil are presented. The mean depth of penetration for the mineral oil was about 40 percent of that for water at the end of a 40 min test. The mean depth of penetration and its rate did not differ significantly for distilled and tap water. The mean depth of penetration rate for both distilled and tap water increased to a maximum and then decreased with test duration, while that for mineral oil had a maximum during the initial period. The ratio h/2a of the pit depth h to the pit diameter 2a varied from 0.04 to 0.13 in water and from 0.06 to 0.20 in mineral oil. Scanning electron microscopy indicates that the pits are initially formed over the grain boundaries and precipitates while the surface grains are deformed under cavitation attack.

Rao, B. C. S.↗
DOE OSTI2021

Grain size dependencies of intergranular solute segregation in nanocrystalline materials

Grain boundary segregation is of increasing importance for stabilizing nanocrystalline alloys, and while segregation is typically modeled as a scale-independent phenomenon, at the finest nanocrystalline grain sizes there are several sources of grain size dependence. Here we provide quantitative detail on two grain size dependencies not previously elaborated, both of which arise from the spectrality of intergranular segregation sites. The first of these arises because a change in grain size affects which portions of the segregation spectrum are occupied by the solutes, with no change in the shape or nature of the spectrum itself. The second of these arises from the presence of higher-order grain junctions, which have unique segregation behaviors and an increasing relative presence at finer grain sizes. This paper uses molecular statics to quantify these size dependencies in detail for the case of an Al(Mg) binary alloy. Together, these two effects combined have a significant effect on the effective McLean segregation energy of more than 6 kJ/mol (from approximately -18.5 kJ/mol at 5 nm to -12.5 kJ/mol at more than 40 nm), with the majority of grain size dependence arising from the spectrality of segregation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dislocation transmission across Σ3{112} incoherent twin boundary: a combined atomistic and phase-field study

Grain boundaries (GBs) in polycrystalline materials act as impediments to dislocation motion and result in strengthening. Understanding slip transmission through GBs, specifically twin boundaries, is essential to understand the plastic deformation behavior of polycrystalline fcc materials. Here the interaction between a glide dislocation and Σ3{112} incoherent twin boundary (ITB) in copper is investigated using a combined atomistic and mesoscale approach. The material parameters and structure of the GB in the mesoscale phase field dislocation dynamics (PFDD) model are informed from Molecular Statics (MS) simulations. The structural unit of the ITB consists of an array of three partial dislocations. The interaction between a glide dislocation impinging on each of the GB partial dislocations is investigated using both PFDD and Molecular Dynamics (MD) with two boundary conditions. Transmission planes predicted by both PFDD and MD (NVT) are in agreement, and show that not all transmission events are direct. Critical transmission stresses predicted by PFDD are in the range of 276 MPa to 1380 MPa, while MD predictions are in the range from 100 MPa to 700 MPa. The PFDD and MD predictions of slip transmission are explained using dislocation theory based on isotropic linear elasticity.

36 MATERIALS SCIENCE↗
NASA NTRS1966

Ceramic research

Effect of grain boundaries and impurities on mechanical behavior of polycrystalline ceramics

CERAMICS↗
DOE OSTI2023

Oxidation in Ca/K-1144 iron-based superconductors polycrystalline compounds

Iron-based superconductors (IBSCs) are a class of material under investigation for the development of superconducting wires in the low-temperature-high magnetic fields power application. Among the various families of IBSCs, the 1144 CaKFe$_4$As$_4$ compound is a promising material able to achieve outstanding superconducting properties with a cheap and simple chemical composition. Oxidation, in these compounds, is considered an obstacle for high intergranular critical current density, J c,GB . A study devoted to the evaluation of oxidation phenomena and their effects on the superconducting properties is thus needed in order to fully understand the involved mechanisms. From the evaluation of polycrystalline samples obtained by a mechanochemically assisted synthesis route, a degradation of the critical temperature and critical currents has been observed concurrently with oxygen accumulation at grain boundaries in open porosities. However, the crystalline structure at an atomic level seems not affected, as well as intragranular superconducting properties assessed by means of calorimetric methods. These results suggest that loss of superconducting properties in Ca/K-1144 compounds following oxidation is significantly associated with the worsening of grain connectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Nucleation and growth of voids in shock loaded copper bicrystals

Understanding the evolution of damage and deformation due to spall at grain boundaries can provide a basis for connecting micro- to macroscale failure behavior in metals under extreme conditions. Copper bicrystal samples were shock loaded using flyer-plate impacts in a light gas gun with shock stresses ranging from 3 to 6 GPa. Pulse duration as well as crystal orientation along the shock direction were varied for a fixed boundary misorientation to determine their effects on void nucleation and coalescence. Samples were soft recovered and cross-sectioned to characterize damage using electron backscattering diffraction and scanning electron microscopy to gather information on damage characteristics at and around the GB, with emphasis on growth of boundary and bulk voids. Chemistry and composition analysis were also performed on samples to determine if trace elements present in a sample affected the threshold for void nucleation. Results show that the kinetics of damage growth at the boundary are strongly affected by stress level and impurities. It was found that the boundary selected had a similar or even lower tendency to show damage than the bulk at low pulse durations and amplitudes. As pulse duration and amplitude increased damage localized at the boundary, which was found to consist of many small voids, indicating that the boundary experienced rapid void nucleation and coalescence. Furthermore, the presence of impurities correlated strongly with scatter on damage evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elucidating the Onset of Plasticity in Sliding Contacts Using Differential Computational Orientation Tomography

Abstract Depending on the mechanical and thermal energy introduced to a dry sliding interface, the near-surface regions of the mated bodies may undergo plastic deformation. In this work, we use large-scale molecular dynamics simulations to generate “differential computational orientation tomographs” (dCOT) and thus highlight changes to the microstructure near tribological FCC alloy surfaces, allowing us to detect subtle differences in lattice orientation and small distances in grain boundary migration. The analysis approach compares computationally generated orientation tomographs with their undeformed counterparts via a simple image analysis filter. We use our visualization method to discuss the acting microstructural mechanisms in a load- and time-resolved fashion, focusing on sliding conditions that lead to twinning, partial lattice rotation, and grain boundary-dominated processes. Extracting and laterally averaging the color saturation value of the generated tomographs allows us to produce quantitative time- and depth-resolved maps that give a good overview of the progress and severity of near-surface deformation. Corresponding maps of the lateral standard deviation in the color saturation show evidence of homogenization processes occurring in the tribologically loaded microstructure, frequently leading to the formation of a well-defined separation between deformed and undeformed regions. When integrated into a computational materials engineering framework, our approach could help optimize material design for tribological and other deformation problems. Graphic Abstract .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of the effect of structural defects from hydride precipitation on superconducting properties of high purity SRF cavity Nb using magneto-optical and electron imaging methods

Abstract Nb is an elemental superconductor with a critical temperature of 9.3 K and is widely used to fabricate superconducting radiofrequency (SRF) cavities for particle accelerators. However, microstructural defects in Nb, such as grain boundaries (GBs) and dislocations, can act as pinning centers for magnetic flux that can degrade SRF cavity performance. Hydrogen contamination is also detrimental to SRF cavity performance due to the formation of normal conducting hydrides during cool down. In this study, disc shaped Nb bi-crystals extracted from high-purity large-grain Nb slices were investigated to study the effects of GBs, hydrogen, and dislocations on superconducting properties. Grain orientation and GB misorientation were measured using Laue x-ray diffraction and electron backscattered diffraction (EBSD) analyses. Cryogenic magneto-optical imaging was used to directly observe magnetic flux penetration below T c = 9.3 K. Damage caused by low temperature precipitation of hydrides and their dissolution upon reheating after cryogenic cycles was examined using electron channeling contrast imaging, and EBSD. The relationships between hydride formation, dislocation content, GBs, cryo-cooling, heat treatment (HT), and flux penetration indicate that both GB character and hydrogen content affect magnetic flux penetration. Such flux penetration could be facilitated by dislocation structures and low angle GBs resulting from hydride precipitation and HT.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling lattice rotation fields from discrete crystallographic slip bands in superalloys

Here in this work, we investigate the relationship between an intense slip band (ISB) and the zone of large lattice rotations that forms ahead of the tip of the ISB. We develop a crystal plasticity finite element model of a discrete ISB lying within an oligocrystalline assembly and calculate the local crystalline stress and lattice rotation fields generated by the ISB. The calculations demonstrate that, first, a region of severe lattice rotations, commonly referred to as a microvolume, does not form without the ISB, and second, large amounts of accumulated slip in the ISB are required to enlarge the microvolume to sizes and rotation magnitudes observed experimentally. Ahead of the ISB tip, the quintessential plastic zone always forms, but the atypical microvolume forms when non-concentrated and spatially diffuse slip is activated by the ISB-induced stress field. This result suggests that the detrimental ISB/microvolume pair will likely appear in pairs of crystals in which transmission of the slip from the ISB is severely blocked by the grain boundary, a hypothesis that we verify with a few target cases.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Effect of autoclave heat treatments on the mechanical properties of the prealloyed powder cobalt-base alloy HS-31

The cobalt-base alloy HS-31 was atomized into powder and then consolidated by extrusion or by hot isostatic pressing (HIP) in an autoclave over a range of temperatures spanning the solidus, approximately 2340 F. Extrusions were subsequently autoclaved at the same conditions. Extrusions autoclaved at 2420 F had a life of 300 hours at 1200 F and 30 hours at 1800 F at stresses that result in a 10-hour life with cast HS-31. Superior stress rupture lives of autoclaved material are probably related to the solidification structure at the grain boundaries as well as to the increased grain size.

Freche, J. C.↗
NASA NTRS1990

Characterization of Iridium Coated Rhenium Used in High-Temperature, Radiation-Cooled Rocket Thrusters

Materials used for radiation-cooled rocket thrusters must be capable of surviving under extreme conditions of high-temperatures and oxidizing environments. While combustion efficiency is optimized at high temperatures, many refractory metals are unsuitable for thruster applications due to rapid material loss from the formation of volatile oxides. This process occurs during thruster operation by reaction of the combustion products with the material surface. Aerojet Technical Systems has developed a thruster cone chamber constructed of Re coated with Ir on the inside surface where exposure to the rocket exhaust occurs. Re maintains its structural integrity at high temperature and the Ir coating is applied as an oxidation barrier. Ir also forms volatile oxide species (IrO2 and IrO3) but at a considerably slower rate than Re. In order to understand the performance limits of Ir-coated Re thrusters, we are investigating the interdiffusion and oxidation kinetics of Ir/Re. The formation of iridium and rhenium oxides has been monitored in situ by Raman spectroscopy during high temperature exposure to oxygen. For pure Ir, the growth of oxide films as thin as approximately 200 A could be easily detected and the formation of IrO2 was observed at temperatures as low as 600 C. Ir/Re diffusion test specimens were prepared by magnetron sputtering of Ir on Re substrates. Concentration profiles were determined by sputter Auger depth profiles of the heat treated specimens. Significant interdiffusion was observed at temperatures as low as 1000 C. Measurements of the activation energy suggest that below 1350 C, the dominant diffusion path is along defects, most likely grain boundaries, rather than bulk diffusion through the grains. The phases that form during interdiffusion have been examined by x ray diffraction. Analysis of heated test specimens indicates that the Ir-Re reaction produces a solid solution phase of Ir dissolved in the HCP structure of Re.

Stulen, R. H.↗
DOE OSTI2024

Influence of grain size on α' Cr precipitation in an isothermally aged Fe-21Cr-5Al alloy

Cr-rich α' precipitation during aging typically leads to hardening and accordingly embrittlement of FeCrAl alloys, which needs to be suppressed. The influence of grain size on α' precipitation was studied by aging coarse-grained (CG), ultra-fine grained (UFG), and nanocrystalline (NC) ferritic Kanthal-D [KD; Fe-21Cr-5Al (wt.%) alloy] at 450, 500 and 550 °C for 500 h. After aging at 450 and 500 °C, less hardening was observed in the UFG KD than in CG KD. Atom probe tomography indicated a lower number density and larger sized intragranular α' in the UFG versus the CG alloy. The smaller grain size and higher defect (vacancy and dislocation) density in the UFG KD facilitated diffusion and accordingly enhanced precipitation kinetics, leading to coarsening of precipitates, as well as saturation of precipitation at lower temperatures, as compared to those in CG KD. No hardening occurred in UFG and CG KD after aging at 550 °C, indicating that the miscibility gap is between 500 and 550 °C. NC KD exhibited softening after aging owing to grain growth. α' precipitation occurred in NC KD aged at 450 °C but not at 500 °C, indicating that miscibility gap is between 450 and 500 °C. Thus, the significantly smaller grain size in NC KD decreased the miscibility gap, as compared to that in CG and UFG KD. Finally, this is attributed to the absorption of vacancies by migrating grain boundaries during aging, suppressing α' nucleation and enhancing Cr solubility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of post-deposition CdCl 2 annealing on electronic properties of CdTe solar cells

The effects of post-deposition CdCl 2 annealing temperature on the electronic properties of CdTe solar cells were investigated. CdTe devices incorporate Mg doped ZnO as a buffer layer and selenization using a CdSe interlayer for reducing the buffer/absorber interface recombination and increasing solar energy absorption respectively. The post-deposition CdCl 2 annealing treatments were done under separate, inert atmospheres of nitrogen and helium across the temperature range 380 to 430 °C. Electrical characterization of devices is carried out including temperature dependent current-voltage characteristics, admittance spectroscopy, and Shockley-Read-Hall recombination analysis. Here, the best improvements in device efficiency are obtained upon annealing at temperature 410 °C. This anneal correlated with reduced back contact barrier in CdTe and reduced grain-boundary barrier height which is beneficial for enhanced charge transport.

14 SOLAR ENERGY↗
DOE OSTI2023

A combined kinetic Monte Carlo and phase field approach to model thermally activated dislocation motion

In this work, a kinetic Monte Carlo (KMC) scheme is integrated into a phase field dislocation dynamics (PFDD) model to account for thermal activation. While the implementation is general and could be applied to many different thermally activated processes, we apply the model to simulate a dislocation transmitting through an interface. Two cases are analyzed: a dislocation transmitting through a strong interface, and a dislocation transmitting through a more realistic grain boundary in tungsten. In conclusion, results and trends for both cases are discussed in detail, and ultimately show that the combined KMC-PFDD algorithm is effective in capturing thermally activated dislocation processes.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Towards High-Throughput Computation of Phase-and Defect Diagrams

The past decade has seen immense advances in our understanding of defect thermodynamics, and the use of machine learning and data science approaches has played a critical role in these advances [1–14]. In the area of grain boundaries (GBs), a particular focus has been placed on the effects of alloying – namely, GB solute segregation or more broadly, GB alloying [15–25], which has been observed and catalogued across a vast range of systems [26–50]. The impacts of solute segregation to GBs are numerous, and can range from negative effects such as embrittlement – for example, due to impurities [51–53], during irradiation [54–61], or during heat treatment [62–65] – to positive effects such as the stabilization against grain growth [66–69], thus enabling the design of nanocrystalline alloys with access to an enhanced range of functional and mechanical properties, and the reduction of embrittlement through the segregation of GB strengthening solutes [49,70–79].

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical and Tribological Performance of Additively Manufactured Nanocrystalline Aluminum via Cryomilling and Cold Spray

In this study, nanocrystalline (NC) aluminum (Al) and magnesium (Mg)-doped Al bulk components were fabricated using a hybrid manufacturing process that combines cryomilling and high-pressure cold spray (HPCS) additive deposition techniques. Yttria-stabilized zirconia (YSZ) was also added during the HPCS process to improve deposition efficiency and build-up thickness via peening. The evolution of morphology, crystallite size, and elemental composition of both cryomilled powders and cold-sprayed (CS’ed) components was systematically characterized using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). Mechanical characterization was performed using Vickers microhardness and uniaxial tensile testing, while the tribological behavior was assessed using sliding wear tests under dry/lubricated conditions. XRD analysis revealed that increased cryomilling duration led to significant crystallite refinement, which directly correlated with enhanced hardness and strength. This mechanical strengthening was accompanied by an increase in coefficient of friction (COF) and lower wear rates. The results also showed that the Mg-doped Al exhibited superior hardness, tensile strength, and tribological performance compared to pure Al. The study further explores the underlying mechanisms responsible for these enhancements, highlighting the potential of solute-assisted grain boundary stabilization in tailoring high-performance NC Al alloys.

36 MATERIALS SCIENCE↗