Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Fission gas retention of densely packed uranium carbonitride tristructural-isotropic fuel particles in a 3D printed SiC matrix

The Transformational Challenge Reactor (TCR) fuel form was designed to contain large, densely packed uranium carbonitride (UCN) tristructural-isotropic (TRISO) fuel particles within a 3D printed SiC matrix, increasing the uranium density compared to conventional TRISO fuel forms and offering full geometric freedom for core design. Here, this work summarizes initial low-burnup, high-power irradiation testing of TCR fuel materials, including loose UCN TRISO particles and integral fuel compacts with ~55% TRISO particles by volume, to evaluate fission gas retention. Fission gasses were fully retained in all loose particle tests and in integral compacts irradiated at low (<250 °C) surface temperatures. Initial testing at higher (~700–750 °C) fuel surface temperatures showed fission gas release (FGR) and complete fracture of three compacts, but no FGR was observed in later high temperature tests (~300–750 °C) of both fueled compacts and loose TRISO particles. Calculated thermal stresses in the failed compacts were far less than the measured strength of the SiC matrix and the stresses in some failed compacts were less than those in compacts that did not show FGR. Thermal stress-induced matrix cracks also would not cause complete fracture because the tensile stresses transition to compression in the higher temperature regions. Therefore, fuel failure was likely not caused by thermal stresses and may have been related to leakage currents from the electrical heaters and erratic fuel surface temperatures that were only observed in the test for which failure was observed. In any case, the matrix cracks propagated through the coatings of TRISO particles located in the high-density matrix regions on the peripheries of the compacts, resulting in measurable fission gas release. The discussion focuses on the importance of understanding matrix density distributions and the particle-matrix interface properties to prevent matrix cracks from causing TRISO particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

An integrated statistical-thermodynamic model for fission gas release and swelling in nuclear fuels

Here, we propose a new model for burst fission gas release induced by microcracking in ceramic nuclear fuels such as uranium dioxide. The model stipulates that the densities of defects in the fuel material, such as microcracks and fission gas bubbles on grain boundaries, evolve in accordance with the second law of thermodynamics. Central to the model is the notion of an effective temperature, conjugate to the configurational entropy of the fuel material, and directly linked to the burnup. The model predicts that microcracking, driven by the internal stress state of the fuel material, reduces the bubble storage capacity of grain boundaries, and accounts for burst fission gas release during rapid temperature transients that simulate power transients, reactor startup, and loss-of-coolant accident conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Impact of grain boundary and surface diffusion on predicted fission gas bubble behavior and release in UO 2 fuel

In this work, we quantify the impact of grain boundary (GB) and surface diffusion on fission gas bubble evolution and fission gas release in UO 2 nuclear fuel using simulations with a hybrid phase field/cluster dynamics model. Here, we begin with a comprehensive literature review of uranium vacancy and xenon atom diffusivity in UO 2 through the bulk, along GBs, and along surfaces. In our model we represent fast GB and surface diffusion using a heterogeneous diffusivity that is a function of the order parameters that represent bubbles and grains. We find that the GB diffusivity directly impacts the rate of gas release via GB transport, and that the GB diffusivity is likely below 104 times the lower value from Olander and van Uffelen. We also find that the surface diffusivity impacts bubble coalescence and mobility, and that the bubble surface diffusivity is likely below 10 -4 times the value from Zhou and Olander.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Ion-gated carbon molecular sieve gas separation membranes

Membrane technology lies at the heart of many industrial gas separation processes and applications. Molecular sieving membranes that break the Robeson limit are desirable for energy-efficient gas separation. In this paper, we report a facile strategy of directly integrating ionic liquids (ILs) into porous membranes. Particularly, the ILs form an ultra-thin layer on the carbon molecular sieve (CMS) membranes rather than penetrating into the pores, acting as a smart gate for gas entry to boost the selectivity. The hybrid membrane exhibits CO 2 permeability >600 barrer and enhanced CO 2 /N 2 selectivity >50, which surpasses the Robeson limit and shows potential in CO 2 /N 2 separation process. Molecular dynamics simulations confirm the gating effect of the IL layer of molecular thickness. In conclusion, this work demonstrates a universal strategy to improve CMS membrane performance by creating an IL-membrane interface and tuning the ion-pore interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Preparation of defect-free asymmetric gas separation membranes with dihydrolevoglucosenone (Cyrene TM ) as a greener polar aprotic solvent

Nonsolvent-induced phase separation (NIPS) is widely used to prepare asymmetric gas separation membranes. Most industrial NIPS casting solution formulations are limited to a small group of glassy polymers and, importantly, require toxic polar aprotic solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), or N-methyl-2-pyrrolidone (NMP). Growing restrictions on the use of such solvents are spurring the search for more benign casting solution formulations that do not compromise membrane performance. Herein this study reports high-flux, defect-free asymmetric polysulfone (PSf) gas separation membranes prepared using dihydrolevoglucosenone (Cyrene TM ), a polar aprotic solvent that is believed to be safer than DMAc, DMF, and NMP, as the majority casting solution component. Optimized formulations and casting conditions produce membranes with hydrogen permeances exceeding 100 gas permeance units (GPU) and selectivities at or above those of dense PSf films. Dry/wet NIPS membrane performance improved with shorter dry step times and increased Cyrene TM loadings relative to the volatile solvent, tetrahydrofuran (THF), in the casting solution. The high water-Cyrene TM Flory-Huggins interaction parameter, $\mathcal{X}12$ , and high casting solution viscosities help suppress the formation of skin layer defects and sublayer macrovoids. In some cases, membrane selectivities were influenced by substructure resistance, providing insight into the relationship between sublayer morphology and membrane performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multi-lab study on the pure-gas permeation of commercial polysulfone (PSf) membranes: Measurement standards and best practices

Gas-separation membranes are a critical industrial component for a low-carbon and energy-efficient future. As a result, many researchers have been testing membrane materials over the past several decades. Unfortunately, almost all membrane-based testing systems are home-built, and there are no widely accepted material standards or testing protocols in the literature, making it challenging to accurately compare experimental results. Further, in this multi-lab study, ten independent laboratories collected high-pressure pure-gas permeation data for H 2 , O 2 , CH 4 , and N 2 in commercial polysulfone (PSf) films. Equipment information, testing procedures, and permeation data from all labs were collected to provide (1) accepted H 2 , O 2 , CH 4 , and N 2 permeability values at 35°C in PSf as a reference standard, (2) statistical analysis of lab-to-lab uncertainties in evaluating permeability, and (3) a list of best practices for sample preparation, equipment set-up, and permeation testing using constant-volume variable-pressure apparatuses. Results summarized in this work provide a reference standard and recommended testing protocols for pure-gas testing of membrane materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The PRad windowless gas flow target

In this work, we report on a windowless, high-density, gas flow target at Jefferson Lab that was used to measure $r_p$, the root-mean-square charge radius of the proton. To our knowledge, this is the first such system used in a fixed-target experiment at a (non-storage ring) electron accelerator. The target achieved its design goal of an areal density of 2$\times$10$^{18}$ atoms/cm$^2$, with the gas uniformly distributed over the 4 cm length of the cell and less than 1% residual gas outside the cell. This design eliminated scattering from the end caps of the target cell, a problem endemic to previous measurements of the proton charge radius in electron scattering experiments, and permitted a precise, model-independent extraction of $r_p$ by reaching unprecedentedly low values of $Q^2$, the square of the electron's transfer of four-momentum to the proton.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Mu2e straw tube tracker gas flow quality control

Here, we present a tracker gas flow quality control method developed for the Mu2e straw tube tracker. Using time-dependent current measurements, we quantify the onset time of ionization gain induced by an 55 F source during gas exchange, which is correlated to the gas conductance in the straw. This allows for the identification of channels with inadequate flow. This approach is broadly applicable to other gaseous detectors that require high-channel-count screening.

Flow↗
DOE OSTI2021

Particle-in-cell techniques for the study of space charge effects in the Advanced Cryogenic Gas Stopper

The Facility for Rare Isotope Beams, FRIB, will significantly increase the rates and varieties of rare isotopes compared to those presently available at existing rare-isotope facilities. The production of stopped beams via the current generation of linear gas stopping devices available is not well matched to the beam intensities that will be available at FRIB. Many experiments that make use of reaccelerated beams, from the ReA facility, greatly benefit from having the highest-intensity, rare-isotope beams possible. Some experiments would also benefit greatly from stopped beams with improved purity. In this paper, the intensity bottlenecks of FRIB’s newest linear gas stopper are studied via experiment and simulation in support of a future detailed conceptual design of a next-generation linear gas stopper that can provide rare-isotope beams with rates of 10^8 pps, a factor of 50 higher than the current state-of-the-art system, with improved beam purity.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

The cyclotron gas stopper at FRIB getting ready for operations

Linear gas stopping cells have been used for nearly two decades to slow down projectile fragments at the National Superconducting Cyclotron Laboratory, now the Facility for Rare Isotope Beams, for experiments with low-energy and reaccelerated beams. In order to efficiently stop and rapidly extract light to medium-mass fast ions, a cyclotron gas-stopper has been constructed. It uses a cyclotron-type magnet and a helium-gas filled stopping chamber to slow down the injected beam. RF ion guides transport the stopped ions to the center of the magnet and axially through the bore before acceleration to <60 keV. Following successful offline tests, the cyclotron stopper was moved to an experimental vault and connected to a new momentum–compression beam line. Beam transport to and into the cyclotron stopper was tested with stable beams. Finally, using 46 K fragments, the first successful stopping and extraction of a high-energy beam with the cyclotron stopper was demonstrated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Fabrication of surrogate oxide spent fuel with various cracking patterns and design of an axial gas transport apparatus

In this article, understanding gas transport behavior in nuclear fuel rods is important for the design, performance, and safety of nuclear fuels. Surrogate materials help enable efficient research by reducing both the costs and the amount of time required. A parametric study using Darcy’s law is completed that demonstrates the feasibility of observing pressure decay over short 13-to-15-cm specimens to enable full characterization of the fabricated specimens using x-ray computed tomography. This paper demonstrates that thermally shocked and mechanically compressed alumina pellets produce surrogate samples whose various cracking patterns are representative of the severity of cracking observed as a function of burnup in irradiated nuclear fuels. Furthermore, image analyses of the cracking patterns—in conjunction with gas transport testing using surrogate samples—affords a valuable accelerated basis for developing gas transport simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Synthesis of imidazolium-mediated Poly(benzoxazole) Ionene and composites with ionic liquids as advanced gas separation membranes

We report thermally rearranged (TR) polymers and ionic polymers are two material classes which have been employed in leading gas separation membranes. This work introduces a novel approach of combining the benzoxazole functionality associated with TR polymers with tailorable cationic groups, yielding a new type of imidazolium-mediated poly(benzoxazole) ionene polymer, “Im-PBO-Ionene” with the aim of enhanced CO 2 separation performance. The structural changes exhibited from the Coulombic interactions between the ionene backbone and the “free” ionic liquid (IL) resulted in enhanced gas separation performance, shown in fundamental characterizations, observed through increased diffusivities and more notably, retained high selectivities and 3x or 5x respective increases in CO 2 permeability upon the addition of 1 or 2 equivalents of IL per polymer repeat unit. These new high-performance ionenes demonstrate the versatility of ionene design and potential of the ionene + IL material platform for gas separation membranes with versatile incorporation of sophisticated functional and structural features.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Crosslinked Matrimid®-like polyimide membranes with unimodal network structure for enhanced stability and gas separation performance

Gas separation membranes have attracted academic and industrial attention, and crosslinking has been identified to be one of the most effective ways to enhance membrane stability. In this paper, a series of crosslinked Matrimid®-like films with unimodal network structures are prepared via thermally end-linking phenylethnyl-terminated BTDA-DAPI oligomers with well-controlled molecular weight (i.e., 3000–15,000 g/mol), wherein the crosslink density (the inter-crosslink chain length) of resulting unimodal networks is systematically varied by using oligomers with various molecular weight. Comprehensive characterizations of chemical structure, thermal properties, microstructures are performed. Pure-gas permeation measurements are performed focusing on H 2 /CH 4 and CO 2 /CH 4 separations as a function of crosslink density. In sharp contrast to the commonly observed permeability reduction in randomly crosslinked networks, all the crosslinked unimodal films, even when densely crosslinked, present markedly enhanced permeability and well-maintained ideal selectivity relative to the uncrosslinked linear counterpart, leading to almost horizontal movements towards upper bounds along with expectedly enhanced membrane stability. In conclusion, it is concluded that introducing bulky groups at the crosslink sites provide a practical means to counteract the densification effect induced by crosslinking and the construction of unimodal networks exemplifies a fundamentally new strategy to regulate the microstructure and property of crosslinked membranes for gas separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

CO 2 capture from wet flue gas using a water-stable and cost-effective metal-organic framework

We report the use of MIL-120 as a water-stable and cost-effective metal-organic framework (MOF) for selectively capturing CO 2 from wet flue gas. Synthesized using inexpensive and environmentally benign reagents in water, MIL-120 possesses one-dimensional pores decorated with hydroxyl-bridged Al(III) ions and benzene rings with an interstitial spacing of 4.78 Å. Carbon dioxide isotherms show steep uptake at low pressure, and the affinity of MIL-120 for CO 2 is 44 kJ mol –1 . CO 2 -loading 13 C solid-state nuclear magnetic resonance and Fourier transform infrared spectra tracking the sorption of CO 2 into MIL-120 revealed that the interplay of pore size, functionality, and dimensionality is vital for CO 2 restriction within the pores of MIL-120. Breakthrough experiments reveal that MIL-120 can capture CO 2 from dry and wet flue gas with uptake capacities of 1.215 and 1.118 mmol g –1 , respectively. Our work highlights the synthetic benefits of MIL-120 and elucidates its selective capture of CO 2 from wet flue gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Composition, Emissions, and Air Quality Impacts of Hazardous Air Pollutants in Unburned Natural Gas from Residential Stoves in California

The presence of hazardous air pollutants (HAPs) entrained in end-use natural gas (NG) is an understudied source of human health risks. We performed trace gas analyses on 185 unburned NG samples collected from 159 unique residential NG stoves across seven geographic regions in California. Our analyses commonly detected 12 HAPs with significant variability across region and gas utility. Mean regional benzene, toluene, ethylbenzene, and total xylenes (BTEX) concentrations in end-use NG ranged from 1.6–25 ppmv–benzene alone was detected in 99% of samples, and mean concentrations ranged from 0.7–12 ppmv (max: 66 ppmv). By applying previously reported NG and methane emission rates throughout California’s transmission, storage, and distribution systems, we estimated statewide benzene emissions of 4,200 (95% CI: 1,800–9,700) kg yr –1 that are currently not included in any statewide inventories–equal to the annual benzene emissions from nearly 60,000 light-duty gasoline vehicles. Additionally, we found that NG leakage from stoves and ovens while not in use can result in indoor benzene concentrations that can exceed the California Office of Environmental Health Hazard Assessment 8-h Reference Exposure Level of 0.94 ppbv–benzene concentrations comparable to environmental tobacco smoke. This study supports the need to further improve our understanding of leaked downstream NG as a source of health risk.

42 ENGINEERING↗
DOE OSTI2026

Locating Undocumented Wells Using Historical Oil and Gas Exploration Maps: A Case Study in Osage County, Oklahoma

Undocumented oil and gas wells lack reliable information about their locations and characteristics, making them difficult to identify. These wells can result in unanticipated delays and costs in the development of nearby surface and subsurface resources, and, if improperly plugged, can cause contamination. This study leverages historical petroleum exploration maps to locate such wells, focusing on Osage County, Oklahoma. Two sets of early 20th century oil and gas exploration maps by the United States Geological Survey were georeferenced and analyzed using a computer vision model to detect well symbols. The locations of detected wells were compared to the location of known wells in the database from the Bureau of Indian Affairs Osage Agency to identify potential undocumented wells. The analysis yielded over 500 potential undocumented wells, with dry holes constituting the largest fraction. Field verification confirmed the presence of some undocumented wells. Comparison with prior work revealed limited overlap, underscoring the complementary value of historical oil and gas maps for locating undocumented wells. This approach demonstrates the utility of integrating historical cartographic resources with modern geospatial and machine learning techniques to improve the identification and management of undocumented wells.

Energy - Petroleum↗
DOE OSTI2026

Modeling Flow and Mass Transfer within Hollow Fiber Packaging for Gas Separation

Hollow fiber membrane modules are used for gas purification by their selective permeation properties. Intensification of the process to minimize the retentate loss and gas pressure involves optimization at various scales. In this work, we outline a numerical investigation of the gas separation performance at the scale of fiber bundles and its impact on module performance. Flow channeling and anisotropy govern the mass-transfer coefficient in axial and cross-flow configurations. These effects are quantified in terms of a permeability tensor or an anisotropy ratio and the effective mass-transfer coefficient or the Sherwood number. The results show a trade-off between purification and recovery. While smaller fibers offer a large specific surface area to enable high purification, it comes at a huge penalty on the separation performance due to reduced penetration within bundles. Optimum performance indicators are emphasized.

Fibers↗
DOE OSTI2021

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗