Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fluid Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Modeling gas, hydrates, and slope stability on the U.S. Atlantic margin during Pleistocene glacial cycles

Changes in temperature and sea level can cause dissociation of methane hydrates in shallow marine sediments, leading to seafloor destabilization. Along the U.S. Atlantic margin, there exists a well-documented history of slope failure and numerous recorded occurrences of gas seeps. Several studies have linked slope failure in the region to gas seepage and hydrate dissociation driven by glacial-interglacial transitions, but this linkage has not been quantitatively demonstrated. Along the shelf edge, in an area where shallow methane gas seeps have been identified, we modeled methane gas and hydrate formation using a one-dimensional fluid flow model. Methane gas formation was modeled over the last 120,000 years to simulate a glacial-interglacial cycle. Here, we ran this model at 16,044 individual locations in the region between 29° N – 45° N and 82° W – 66° W at a resolution of 1 x 1 arcminutes, focusing specifically on water depths between 200 and 1000 m that bracket the seafloor outcrop of the base of the hydrate stability zone. Using historic temperature and pressure records from the last 120,000 years, sediment properties in the area, and factor of safety calculations, we found that hydrate dissociation alone is unlikely to cause sediment failure in the region, implying that an additional driving force would be necessary for failure to occur.

Hydrate dissociation↗
DOE OSTI2023

Thermal Scattering Law Data Development for Paraffin Wax

Paraffin wax is often used as a nuclear moderator to slow down the fast neutrons in experimental critical assemblies [1]. It is a colorless and soft solid material that consists primarily of straight-chain alkanes (n-alkanes), which are hydrocarbons with the general formula CnH2n+2 [2-3]. The length of the hydrocarbon chain ranges from C20 to C30 and higher [2]. It is distinguished by its solid state at room temperature and begins to melt above approximately 310 K [4]. Paraffin wax is a commonly employed substance in the manufacture of shielding. One of its noteworthy characteristics is its ability to effectively absorb the neutrons. Also, it possesses a high macroscopic cross section, which enables it to efficiently moderate neutrons. As a result, paraffin wax is extensively utilized in various applications where moderation and shielding of neutrons are needed. For simulations, it is necessary to evaluate its thermal scattering law (TSL) and cross sections. Computationally, classical molecular dynamics (CMD) simulations provide the capability of simulating atomic details. For example, several unary, binary, and few multi component mixtures have been investigated of the paraffin model by using molecular dynamics simulations [5-12]. An assessment of thermal neutron scattering in a heavy paraffinic oil treated both as a solid and a viscous fluid containing 25% linear branched paraffin (C30H62), 35% one ring cycloalkane (C30H60), 15% two rings cycloalkane (C30H58), and 25% aromatic (C30H60) chains has been studied using CMD simulations for producing TSL data [13]. Nevertheless, there is lack of TSL and cross section data for paraffin wax as most of the reported analyses focus on the unary and binary mixture of n-alkanes, which is not consistent with actual paraffin wax [2]. In this work, we applied the equilibrium CMD simulations technique to explore the structure and dynamical properties of wax, which are fundamental input to calculate the TSL. A paraffin wax system was modeled using the CMD code LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator) [14-15] with the semi-empirical COMPASS [16] force field. The density of state (DOS) was calculated from the normalized velocity autocorrelation function (VACF), which is the Fourier transform of the normalized VACF. The DOS was used for the calculation of the TSL and thermal scattering cross sections. The paraffin wax atomic system was constructed by using the MedeA material design platform [17], and was benchmarked using available properties (i.e., density, bond lengths, angles, diffusivity, and viscosity).

Nuclear Criticality Safety Program (NCSP)↗
DOE OSTI2022

Quantitative interpretation of time-lapse seismic data at Farnsworth field unit: Rock physics modeling, and calibration of simulated time-lapse velocity responses

Here, this study investigates the contribution of fluid saturation variation to the time-lapse velocity response by performing fluid substitution modeling. The methodology is exemplified by the time-lapse seismic monitoring of carbon dioxide at Farnsworth field unit (FWU). In order to evaluate the fluid distribution in a matured oil reservoir, the Southwest Regional Partnership (SWP) acquired multiple vertical seismic profile (VSP) surveys at different times during the CO 2 –water alternatinggas (WAG) injection period. In this work, we present a thorough methodology for computing the elastic response of the saturated rock for different fluid saturations using a site-specific petro-elastic model (PEM). The output from the PEM was combined with results from a fluid compositional model to compute the seismic velocities at times corresponding to each VSP survey. To produce a calibrated simulated response, the measured time-lapse seismic velocities were integrated into the numerical simulation model. The mismatches between the predicted and measured time-lapse velocities were minimized through an iterative calibration process using a trained artificial neural network proxy (ANN) coupled with a particle swarm optimizer (PSO). Our study indicates that the hybrid optimization workflow can effectively perform the history matching. With an accurate prediction of the hydrodynamic properties, the migration of CO 2 within the subsurface was modeled by predicting the spatial velocity distribution for a radius of 305 m around the injection well. The technology demonstrated and the expertise gained from this study can guide similar CO 2 -WAG projects.

58 GEOSCIENCES↗
DOE OSTI2021

Evolution of anisotropy with saturation and its implications for the elastoplastic responses of clay rocks

Many clay rocks have distinct bedding planes. Experimental studies have shown that their mechanical properties evolve with the degree of saturation (DOS), often with higher stiffness and strength after drying. For transversely isotropic rocks, the effects of saturation can differ between the bed-normal (BN) and bed-parallel (BP) directions, which gives rise to saturation-dependent stiffness and strength anisotropy. Accurate prediction of the mechanical behavior of clay rocks under partially saturated conditions requires numerical models that can capture the evolving elastic and plastic anisotropy with DOS. In this study, we present an anisotropy framework for coupled solid deformation-fluid flow in unsaturated elastoplastic media. Here we incorporate saturation-dependent strength anisotropy into an anisotropic modified Cam-Clay (MCC) model and consider the evolving anisotropy in both the elastic and plastic responses. The model was calibrated using experimental data from triaxial tests to demonstrate its capability in capturing strength anisotropy at various levels of saturation. Through numerical simulations, we demonstrate the role of evolving stiffness and strength anisotropy in the mechanical behavior of clay rocks. Plane strain simulations of triaxial compression tests were also conducted to demonstrate the impacts of material anisotropy and DOS on the mechanical and fluid flow responses.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Calibrating uncertain parameters in melt pool simulations of additive manufacturing

Melt pool scale numerical modeling of additive manufacturing (AM) processes can provide predictive capabilities and theoretical insight into the process-property-structure-performance relationships for AM parts. Despite capabilities of numerical models to solve complex multi-physics problems, it is often important to consider a tradeoff between detailed physics and computational cost. Therefore, sources of uncertainty in both experimental conditions and the parameters needed for modeling require models to be validated against empirical evidence. Here, a method is proposed to calibrate uncertain parameters used in continuum-scale melt pool models for powder bed fusion (PBF) AM. Both a simplified heat transfer model and a heat transfer and fluid flow model were investigated. A surrogate model and Markov chain-based optimization algorithm calibrated melt pool geometry for models within experimental variation of the target melt pool width and depth from the NIST AM-Bench 2018-02 dataset. The melt pool temperature distributions, solidification parameters, and simulated multi-layer solidification microstructures were compared between the two models. Similar results from both models indicate that calibrated, lower fidelity numerical models may be used in place of higher fidelity models to generate melt pool solidification data. Finally, these calibrated models therefore enable lower computational cost melt pool simulations without a noticeable decrease in simulation accuracy for grain-scale microstructure simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Novel Multiphysics Multiscale Multiporosity Shale Gas Transport Model for Geomechanics/Flow Coupling in Steady and Transient States

Summary A novel multiphysics multiscale multiporosity shale gas transport (M3ST) model was developed to investigate shale gas transport in both transient and steady states. The microscale model component contains a kerogen domain and an inorganic matrix domain, and each domain has its own geomechanical and gas transport properties. Permeabilities of various shale cores were measured in the laboratory using a pulse decay permeameter (PDP) with different pore pressure and confining stress combinations. The PDP-measured apparent permeability as a function of pore pressure under two effective stresses was fitted using the microscale M3ST model component based on nonlinear least squares fitting (NLSF), and the fitted model parameters were able to provide accurate model predictions for another effective stress. The parameters and petrophysical properties determined in the steady state were then used in the transient-state, continuum-scale M3ST model component, which performed history matching of the evolutions of the upstream and downstream gas pressures. In addition, a double-exponential empirical model was developed as a powerful alternative to the M3ST model to fit laboratory-measured apparent permeability under various effective stresses and pore pressures. The developed M3ST model and the research findings in this study provided critical insights into the role of the multiphysics mechanisms, including geomechanics, fluid dynamics and transport, and the Klinkenberg effect on shale gas transport across different spatial scales in both steady and transient states.

Engineering↗
DOE OSTI2022

A method for generating moving, orthogonal, area preserving polygonal meshes

A new method for generating locally orthogonal polygonal meshes from a set of generator points is presented in which polygon areas are a constraint. The area constraint property is particularly useful for particle methods where moving polygons track a discrete portion of material. Because Voronoi polygon meshes have some very attractive mathematical and numerical properties for numerical computation, a generalization of Voronoi polygon meshes was formulated that enforces a polygon area constraint. Area constrained moving polygonal meshes allow one to develop hybrid particle-mesh numerical methods that display some of the most attractive features of each approach. It is shown that this mesh construction method can continuously reconnect a moving, unstructured polygonal mesh in a pseudo-Lagrangian fashion without change in cell area/volume, and the method's ability to simulate various physical scenarios is shown. Overall, the advantages are identified for incompressible fluid flow calculations, with demonstration cases that include material discontinuities of all three phases of matter and large density jumps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Synergistic ground and orbital observations of iron oxides on Mt. Sharp and Vera Rubin ridge

Visible/short-wave infrared spectral data from the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) show absorptions attributed to hematite at Vera Rubin ridge (VRR), a topographic feature on northwest Mt. Sharp. The goals of this study are to determine why absorptions caused by ferric iron are strongly visible from orbit at VRR, and to improve interpretation of CRISM data throughout lower Mt. Sharp. These goals are achieved by analyzing coordinated CRISM and in situ spectral data along the Curiosity Mars rover’s traverse. VRR bedrock within areas that have the deepest ferric absorptions in CRISM data also have the deepest ferric absorptions measured in situ. This suggests strong ferric absorptions are visible from orbit at VRR because of the unique spectral properties of VRR bedrock. Dust and mixing with basaltic sand additionally inhibit the ability to measure ferric absorptions in bedrock stratigraphically below VRR from orbit. There are two implications of these findings: (1) Ferric absorptions in CRISM data initially dismissed as noise could be real, and ferric phases are more widespread in lower Mt. Sharp than previously reported, (2) Patches with the deepest ferric absorptions in CRISM data are, like VRR, reflective of deeper absorptions in the bedrock. One model to explain this spectral variability is late-stage diagenetic fluids that changed the grain size of ferric phases, deepening absorptions. Curiosity’s experience highlights the strengths of using CRISM data for spectral absorptions and associated mineral detections, and the caveats in using these data for geologic interpretations and strategic path planning tools.

58 GEOSCIENCES↗
DOE OSTI2022

Plasma Facing Components with Capillary Porous System and Liquid Metal Coolant Flow

Liquid metal can create a renewable protective surface on plasma facing components (PFC), with an additional advantage of deuterium pumping and the prospect of tritium extraction if liquid lithium (LL) is used and maintained below 450 C, the temperature above which LL vapor pressure begins to contaminate the plasma. LM can also be utilized as an efficient coolant, driven by the Lorentz force created with the help of the magnetic field in fusion devices. Capillary porous systems can serve as a conduit of LM and simultaneously provide stabilization of the LM flow, protecting against spills into the plasma. Recently a combination of a fast-flowing LM cooling system with a porous plasma facing wall (CPSF) was investigated [Khodak and Maingi (2021)]. The system takes an advantage of a magnetohydrodynamics velocity profile, as well as attractive LM properties to promote efficient heat transfer from the plasma to the LL at low pumping energy cost, relative to the incident heat flux on the PFC. In case of a disruption leading to excessive heat flux from the plasma to the LM PFCs, LL evaporation can stabilize the PFC surface temperature, due to high evaporation heat and apparent vapor shielding. The proposed CPSF was optimized analytically for the conditions of a Fusion Nuclear Science Facility [Kessel et al. (2019)]: 10T toroidal field and 10 MW/m2 peak incident heat flux. Computational fluid dynamics analysis confirmed that a CPSF system with 2.5 mm square channels can pump enough LL so that no additional coolant is needed.

High Heat Flux↗
DOE OSTI2021

Numerical Investigation of Enhanced Dehumidification Processes By Using Dielectrophoresis Principles in Moist Airflows

Dispersed particle-laden flows are encountered in many building and industrial applications, such as flow in a fluidized bed, hydrocarbon transportation in pipelines, and the fouling of air-cooled heat exchangers (Kuruneru et al., 2016; Ray et al., 2019; Wang et al., 2019). Computational fluid dynamic (CFD) models have been developed in recent years to depict particle-fluid and particle-particle interactions in laminar or turbulent flows with increasing accuracy and stability. One particular particle-laden system of interest for moisture control is electrically-enhanced condensation in air and water droplet flows. Electrically-enhanced condensation consists of the use of highly charged water droplets injected in the moist air. The droplets become electric seeds that attract polar water vapor molecules to their surfaces and promote condensation. The nucleation and growth of the charged droplets deplete the vapor phase near a droplet, which is compensated for by the dielectrophoresis flow and diffusion. Dielectrophoresis flow involves surrounding vapor at a distance of about 10 to 100 nm for droplets charged by an electrospray compared to ~2 nm for a single electron charge in a droplet. As the vapor molecules collapse on the surface of the droplets, their initial electrical charge decreases with time due to the neutralization of the ions. While the physics of this phenomena is well known, engineering models for predicting the condensation rates are not available. This work computationally investigates dehumidification of moist airflow in a converging rectangular duct. The objective is to develop an engineering model that predicts water vapor condensation by employing dielectrophoresis principles. We construct a Computational Fluid Dynamics (CFD) model of the duct with electrically-enhanced condensation. The model is implemented in the open-source software OpenFOAM. We utilize the Multi-Phase Particle-In-Cell (MP-PIC) method coupled with a Population Balance Equation (PBE) approach to simulate the particle-laden system. This methodology is an Eulerian-Lagrangian approach used to simulate the droplets' behavior in the humid air. The MP-PIC approach (Andrews and O'Rourke, 1996) mitigates the computational cost by parceling several fundamental particles with similar properties (such as types, sizes, and temperature) into one computational particle. Thus, the billions of particles can be substituted by millions of computational particles without significant loss of information. The PBE was considered with the Lagrangian frame to combine the particle distribution function used in MP-PIC (Kim et al., 2020). This approach preserves mass and energy conservation between the phases in the Eulerian and Lagrangian structures. The PBE in this procedure was directly linked to the discrete parcels, making the simulation of the particle distribution computationally efficient and robust. The MP-PIC-PBE approach used in the present work was applied to the dehumidification of air. Water droplets were injected in the air stream and forced to grow according to experimentally derived correlation. The experiments were conducted on a converging duct with the same geometry and boundary conditions used to build the CFD model. This approach enabled us to approximate the effect of dielectrophoresis phenomena on the droplet and air interface. This presentation will discuss the details of the new CFD model built for the duct, the implementation of the model in OpenFOAM CFD programming language, and the experimental validation of the newly developed model. The results revealed a moderate yet measurable increase in droplet diameter due to water vapor condensation at the vapor-liquid interface of the electrically charged droplets' surface. The seed water droplet particles grew in size by capturing the water vapor in the surrounding air. The OpenFOAM model predicted reductions of humidity in the air from 5 to 10 percent.

Yel Mahi, Maliha↗
DOE OSTI2023

Simulating dielectric spectra: A demonstration of the direct electric field method and a new model for the nonlinear dielectric response

Here we demonstrate a method to compute the dielectric spectra of fluids in molecular dynamics (MD) by directly applying electric fields to the simulation. We obtain spectra from MD simulations with low magnitude electric fields (≈0.01 V/Å) in agreement with spectra from the fluctuation–dissipation method for water and acetonitrile. We examine this method’s trade-off between noise at low field magnitudes and the nonlinearity of the response at higher field magnitudes. We then apply the Booth equation to describe the nonlinear response of both fluids at low frequency (0.1 GHz) and high field magnitude (up to 0.5 V/Å). We develop a model of the frequency-dependent nonlinear response by combining the Booth description of the static nonlinear dielectric response of fluids with the frequency-dependent linear dielectric response of the Debye model. We find good agreement between our model and the MD simulations of the nonlinear dielectric response for both acetonitrile and water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Raman Wavelength Conversion in Ionic Liquids

Here, we explore the use of room-temperature ionic liquids (ILs) as Raman wavelength converters. ILs provide an engineerable framework to design suitable liquids for wavelength conversion over a broad spectral range, through careful selection of the molecular structures of the IL anions and cations so that specific characteristics can be obtained, such as a desirable Raman shift, low Brillouin scattering, and good optical transmission in the pump and Stokes wavelengths. Applying such criteria, we demonstrate that 1-ethyl-3-methylimidazolium dicyanamide (EMIM DCA) is an effective medium for conversion of 532-nm pulses from a Q-switched Nd :YAG laser to 603 nm. This corresponds to an approximate 2200 cm –1 shift, which can be used to generate mid-infrared radiation through subsequent difference frequency generation for optical pumping of CO 2 lasers. Threefold-higher Raman conversion efficiency is obtained in EMIM DCA compared with water under identical conditions in a proof-of-principle single-pass conversion setup, resulting in an efficient generation of multimillijoule, <6 ns duration, high-quality orange laser pulses in a wavelength region that is difficult to access at high energies. Consequently, we examine ILs representing two other classes of Raman-active functional groups and obtain conversion up to the fifth-order Stokes shift and first anti-Stokes shift. Through the tunable selection of their components and their useful dynamical properties, ILs provide a platform for efficient, simple, and alignment-tolerant high-energy Raman shifting with numerous industrial and technological applications.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content

3D printing with cementitious materials is an emerging technology and provides an active area of research. Despite this, there are only limited studies that examine the pumping behaviour of high yield stress fluids such as printable concrete. We present a study on the rheological behaviour of 3D printable cementitious materials with different aggregate-to-binder ratios (a/b) and analyse the pumping and printing characteristics with the measured rheological parameters. We observed that an increase in a/b resulted in a significant increase of plastic viscosity, and a nominal increase in yield stress and storage modulus. The variation in plastic viscosity and yield stress with increasing aggregate content was analysed with the Krieger-Dougherty and Chateau-Ovarlez-Trung model, respectively. Also, the rheological properties of the paste rich lubrication layer during pumping were determined with the help of a tribometer. The yield stress and viscous constant of the lubrication layer increase with the increase in a/b. The pumping pressure predictions were carried out by a suitable theoretical model by considering appropriate flow conditions for different mixtures. The variation in critical height of printed elements with an increase in a/b was correlated with the observed rheological parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated temperatures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple)trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A Baseline CFD model is defined and its accuracy established to be comparable to(and which usually exceeds) the accuracy of existing HTC (heat-transfer coefficient) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled),generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.1

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated tempera-tures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple) trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A baseline CFD model is defined and its accuracy established to be comparable to (and which usually exceeds) the accuracy of existing HTC (heat-transfer correlation) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled), generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Robustness of cement-based materials: From dosage variations to yield stress fluctuations

The idea behind the present work is to assess robustness of fresh cement-based materials (i.e. their ability to display the same properties when submitted to variations in the way they are produced) from a generic and analytical point of view. First, analytical models from literature relating components proportions and yield stress are combined into a multi-scale and physical approach and compared to our experimental yield stress measurements. In the second part, the derivation of these analytical relationships is used to assess robustness as a function of components proportions, which allows for the most sensitive variations to be mapped onto component dosage from a yield stress point of view. In the case of fluid concretes, this approach showcases the interest of working at slightly higher water content and slightly lower aggregates fraction along with benefits of viscosity modifying agents / plasticizers combination.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigating the Longevity of Hydraulic Power Take-Off Piston Seals in Wave Energy Converters

Wave energy converters (WECs) utilize hydraulic power take-off (PTO) systems. Hydraulic cylinder seals, which are commonly made from thermoplastic or elastomeric polymers, play a vital role in PTO system functionality as they are responsible for containing and isolating high-pressure fluids. However, manufacturers of WECs have identified a significant concern regarding the longevity of hydraulic piston seal wear due to a combination of stressors, such as high pressure, elevated temperature, chemical corrosion, and/or environmental conditions. Seal failure can result in a loss of tightness and fluid leakage, and consequently a reduction in the efficiency of WECs. Seal manufacturers do not typically provide durability data as the materials are not specifically designed for WEC applications, nor do they account for real-world conditions that the materials may be exposed to. Additionally, there is no comparative performance data available between different seal manufacturers, creating uncertainty in hydraulic PTO designs for WECs. This paper reviews the current state of available seal materials for WEC hydraulic PTO systems, seal selection criteria for WEC applications, potential seal degradation mechanisms, and also material properties of the seals, such as density, hardness, tensile strength, and operating temperature. In addition, this paper also examines current evaluation procedures for estimating the durability of WEC PTO seals. Lastly, additional research on estimating the lifespan of piston and rod polymer seals used in hydraulic PTO systems is proposed.

Elen, Muthu↗
DOE OSTI2022

Molecular-scale mechanisms of CO 2 mineralization in nanoscale interfacial water films

The calamitous impacts of untethered carbon emission from fossil-fuel-burning energy infrastructure calls for accelerated development of large-scale CO 2 capture, utilization, and storage technologies that are underpinned by fundamental understanding of molecular-level chemical processes. In the subsurface, rocks rich in divalent metals can react with CO 2 , permanently sequestering it in the form of stable metal carbonate minerals, with the CO 2 -H 2 O composition of the post-injection pore fluid acting as a primary control variable. Herein, we compare mechanistic reaction pathways for aqueous-mediated carbonation with carbon mineralization occurring in nanoscale adsorbed water films. In the extreme of pores filled with a CO 2 -dominant fluid, carbonation reactions are confined to nanometer-thick water films coating mineral surfaces, which enable metal cation release, transport, nucleation, and crystallization of metal carbonate minerals. Though seemingly counterintuitive, laboratory studies have demonstrated facile carbonation rates in these low water environments, which in recent years has begun to be better understood in mechanistic detail. The overarching objective of this review is to delineate the unique underlying molecular-scale reaction mechanisms that govern CO 2 mineralization in these reactive and dynamic quasi-2D interfaces. Here. we highlight the importance of understanding unique properties in thin water films, such as how water dielectric properties, and consequently ion solvation/hydration behavior, can change under nanoconfinement. We conclude by identifying important frontiers for future work and opportunities to exploit these fundamental chemical insights for decarbonization technologies in the 21st century.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗