Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flow Conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Effects of Tip Clearance and Casing Recess on Heat Transfer and Stage Efficiency in Axial Turbines

Calculations were performed to assess the effect of the tip leakage flow on the rate of heat transfer to blade, blade tip and casing. The effect on exit angle and efficiency was also examined. Passage geometries with and without casing recess were considered. The geometry and the flow conditions of the GE-E 3 first stage turbine, which represents a modem gas turbine blade were used for the analysis. Clearance heights of 0%, 1%, 1.5% and 3% of the passage height were considered. For the two largest clearance heights considered, different recess depths were studied. There was an increase in the thermal load on all the heat transfer surfaces considered due to enlargement of the clearance gap. Introduction of recessed casing resulted in a drop in the rate of heat transfer on the pressure side but the picture on the suction side was found to be more complex for the smaller tip clearance height considered. For the larger tip clearance height the effect of casing recess was an orderly reduction in the suction side heat transfer as the casing recess height was increased. There was a marked reduction of heat load and peak values on the blade tip upon introduction of casing recess, however only a small reduction was observed on the casing itself. It was reconfirmed that there is a linear relationship between the efficiency and the tip gap height. It was also observed that the recess casing has a small effect on the efficiency but can have a moderating effect on the flow underturning at smaller tip clearances.

Ameri, A. A.↗
NASA NTRS1995

Progress in Navier-Stokes Simulation of Delta Wing Maneuver Aerodynamics

This paper will summarize recent progress in the numerical simulation of high incidence vortical flow about a generic 65 degree sweep delta wing using the three dimensional, time-dependent, Reynolds averaged, Navier-Stokes (RANS) equations. Computations have been carried out at 15 and 30 degrees angle of attack under subsonic turbulent flow conditions, and compared with experimental data provided by Hanff, Jenkins, and their colleagues. This work has already been published elsewhere and widely disseminated. Computations carried out at 15 degrees angle of attack included static roll angles ranging up to 65 degrees, and a large-amplitude (40 degree), high rate (7 Hz), forced roll motion. There was very good agreement between computed and experimental forces and moments, and static surface pressures. There was a significant hysteresis of the dynamic rolling moment due to the high rate of roll motion. At this angle of attack, no vortex breakdown was observed in the computations or experiment. Computations were also carried out at 30 degrees angle of attack, where vortex breakdown was present in both the computations and experiment. There was overall good agreement in the computed and experimental forces and moments. The static rolling moment varied with roll angle in a highly nonlinear manner, and exhibited three stable trim points and two unstable trim points. This behavior was attributed to the presence of vortex breakdown. Two large-amplitude (30 degrees), high-rate (10 Hz) forced roll motions were computed. The dynamics of the vortex breakdown motion was dramatically visualized by tracking the time-dependent motion of particles released near the delta wing apex. This numerical visualization is analogous to experimental smoke flow techniques. In one of the dynamic cases the breakdown was found to move off the wing, convected downwind of the trailing edge, and later reformed near the trailing edge through an instability of the vortex core. A damped free-to-roll motion was also computed by releasing the wing from rest at 40 degrees of roll. The wing went to the same trim point as in the experiment.

Chaderjian, Neal M.↗
NASA NTRS1995

Method and Apparatus for Measuring Fluid Flow

The invention is a method and apparatus for monitoring the presence, concentration, and the movement of fluids. It is based on utilizing electromagnetic measurements of the complex permittivity of the fluids for detecting and monitoring the fluid. More particularly the apparatus uses one or more microwave probes which are placed at the locations where the measurements are to be made. A radio frequency signal is transmitted to the probe and the reflected signal is phase and amplitude detected at a rapid rate for the purpose of identifying the fluids, based on their dielectric constant at the probe. The apparatus can be used for multiple purposes including measures of flow rates, turbulence, dispersion, fluid identification, and changes in flow conditions of multiple fluids or multiple states of a single fluid in a flowline or a holding container. The apparatus includes a probe consisting of two electrical conductors separated by an insulator. A radio frequency signal is communicated to the probe and is reflected back from the portion of the probe exposed to the fluid. The radio frequency signal also provides a reference signal. An oscillator generates a second signal which combined with each of the reference signal and the reflected signal to produce signals of lower frequencies to facilitate filtering and amplifying those signals. The two signals are then mixed in a detector to produce an output signal that is representative of the phase and amplitude change caused by the reflection of the signal at the probe exposed to the fluid. The detector may be a dual phase detector that provides two such output signals that are in phase quadrature. A phase shifter may be provided for selectively changing the phase of the reference signal to improve the sensitivity of at least one of the output signals for more accurate readings and/or for calibration purposes. The two outputs that are in quadrature with respect to each other may be simultaneously monitored to account for drift errors. The output signals are digitized and provided to a computer at a sample rate which may be very high. The computer is operable to identify the fluid based on its complex permittivity as may be useful for identifying the flow rates, determining the fluid mixture ratio, detecting impurities in the fluid, and so forth. Novelty is believed to reside in the use of the real part of complex permittivity to measure small difference in permittivity of the fluid.

Arndt, G. Dickey↗
NASA NTRS2006

Test Capability Enhancements to the NASA Langley 8-Foot High Temperature Tunnel

The NASA Langley 8-Foot High Temperature Tunnel produces true enthalpy environments simulating flight from Mach 4 to Mach 7, primarily for airbreathing propulsion and aerothermal/thermo-structural testing. Flow conditions are achieved through a methane-air heater and nozzles producing aerodynamic Mach numbers of 4, 5 or 7 and have exit diameters of 8 feet or 4.5 feet. The 12-ft long free-jet test section, housed inside a 26-ft vacuum sphere, accommodates large test articles. Recently, the facility underwent significant upgrades to support hydrocarbon fueled scramjet engine testing and to expand flight simulation capability. The upgrades were required to meet engine system development and flight clearance verification requirements originally defined by the joint NASA-Air Force X-43C Hypersonic Flight Demonstrator Project and now the Air Force X-51A Program. Enhancements to the 8-Ft. HTT were made in four areas: 1) hydrocarbon fuel delivery; 2) flight simulation capability; 3) controls and communication; and 4) data acquisition/processing. The upgrades include the addition of systems to supply ethylene and liquid JP-7 to test articles; a Mach 5 nozzle with dynamic pressure simulation capability up to 3200 psf, the addition of a real-time model angle-of-attack system; a new programmable logic controller sub-system to improve process controls and communication with model controls; the addition of MIL-STD-1553B and high speed data acquisition systems and a classified data processing environment. These additions represent a significant increase to the already unique test capability and flexibility of the facility, and complement the existing array of test support hardware such as a model injection system, radiant heaters, six-component force measurement system, and optical flow field visualization hardware. The new systems support complex test programs that require sophisticated test sequences and precise management of process fluids. Furthermore, the new systems, such as the real-time angle of attack system and the new programmable logic controller enhance the test efficiency of the facility. The motivation for the upgrades and the expanded capabilities is described here.

Harvin, S. F.↗
NASA NTRS2022

Nonlinear Evolution of Instabilities in a Laminar Separation Bubble at a Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

Hypersonic flow↗
NASA NTRS2022

Nonlinear Evolution of Instability in a Laminar Separation Bubble at Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

High speed flow↗
NASA NTRS2019

Use of Polarimetric Radar Measurements to Constrain Simulated Convective Cell Evolution: A Pilot Study with Lagrangian Tracking

To probe the potential value of a radar-driven field campaign to constrain simulation of isolated convection subject to a strong aerosol perturbation, convective cells observed by the operational KHGX weather radar in the vicinity of Houston, Texas, are examined individually and statistically. Cells observed in a single case study of onshore flow conditions during July 2013 are first examined and compared with cells in a regional model simulation. Observed and simulated cells are objectively identified and tracked from observed or calculated positive specific differential phase (K(sub DP)) above the melting level, which is related to the presence of supercooled liquid water. Several observed and simulated cells are subjectively selected for further examination. Below the melting level, we compare sequential cross sections of retrieved and simulated raindrop size distribution parameters. Above the melting level, we examine time series of KDP and radar differential reflectivity (Z(sub DR)) statistics from observations and calculated from simulated supercooled rain properties, alongside simulated vertical wind and supercooled rain mixing ratio statistics. Results indicate that the operational weather radar measurements offer multiple constraints on the properties of simulated convective cells, with substantial value added from derived K(sub DP) and retrieved rain properties. The value of collocated three-dimensional lightning mapping array measurements, which are relatively rare in the continental US, supports the choice of Houston as a suitable location for future field studies to improve the simulation and understanding of convective updraft physics. However, rapid evolution of cells between routine volume scans motivates consideration of adaptive scan strategies or radar imaging technologies to amend operational weather radar capabilities. A 3-year climatology of isolated cell tracks, prepared using a more efficient algorithm, yields additional relevant information. Isolated cells are found within the KHGX domain on roughly 40 % of days year-round, with greatest concentration in the northwest quadrant, but roughly 5-fold more cells occur during June through September. During this enhanced occurrence period, the cells initiate following a strong diurnal cycle that peaks in the early afternoon, typically follow a south-to-north flow, and dissipate within 1 h, consistent with the case study examples. Statistics indicate that ∼ 150 isolated cells initiate and dissipate within 70 km of the KHGX radar during the enhanced occurrence period annually, and roughly 10 times as many within 200 km, suitable for multi-instrument Lagrangian observation strategies. In addition to ancillary meteorological and aerosol measurements, robust vertical wind speed retrievals would add substantial value to a radar-driven field campaign.

Fridlind, Ann M.↗
NASA NTRS2017

Stabilization of Hypersonic Boundary Layers by Linear and Nonlinear Optimal Perturbations

The effect of stationary, finite-amplitude, linear and nonlinear optimal perturbations on the modal disturbance growth in a Mach 6 axisymmetric flow over a 7 deg. half-angle cone with 0:126 mm nose radius and 0:305 m length is investigated. The freestream parameters (M = 6, Re(exp 1) = 18 x 10(exp. 6) /m) are selected to match the flow conditions of a previous experiment in the VKI H3 hypersonic tunnel. Plane-marching parabolized stability equations are used in conjunction with a partial-differential equation based planar eigenvalue analysis to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode and first-mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone; however, subharmonic first-mode instabilities, which are destabilized by the presence of the streaks, do reach N = 6 near the end of the cone. The highest stabilization is observed at streak amplitudes of approximately 20 percent of the freestream velocity. Because the use of initial disturbance profiles based on linear optimal growth theory may yield suboptimal control in the context of nonlinear streaks, the computational predictions are extended to nonlinear optimal growth theory. Results show that by using nonlinearly optimal perturbation leads to slightly enhanced stabilization of plane Mack mode disturbances as well as reduced destabilization of subharmonic first-mode disturbances.

Incompressible boundary layer↗
NASA NTRS1966

Valve effectively controls amount of contaminant in flow stream

Contaminant valve with a coaxial groove rotor uniformly deposits contaminant into a flow stream under full pressure and flow conditions. The valve tests filters and filter elements of hydraulic oil, fuel, or lubricant systems without any detrimental effect on the performance.

Schnitzer, T. E.↗
NASA NTRS1957

Boundary-Layer-Transition and Heat-Transfer Measurements from Flight Tests of Blunt and Sharp 50 Degree Cones at Mach Numbers from 1.7 to 4.7

Boundary-layer-transition and heat-transfer measurements were obtained from flight tests of blunt and sharp cones having apex angles of 50 deg. The test Mach number range was from 1.7 to 4.7, corresponding to free-stream Reynolds numbers, based on cone base diameter, of 18. 3 x 10(exp 6) and 32.1 x 10(exp 6), respectively. Transition on both models occurred at a local Reynolds number of 1 x 10(exp 6) to 2 X 10(exp 6) based on distance from the stagnation point. Transition Reynolds numbers based on momentum thickness were between 320 and 380 for the blunt cone. The model surface roughness was 25 rms microinches or greater. Turbulent heat transfer to the conical surface of the blunt cone at a Mach number of 4 was 30 percent less than that to the surface of the sharp cone. Available theories predicted heat-transfer coefficients reasonably well for the fully laminar or turbulent flow conditions.

BLUNT BODY↗
NASA NTRS1967

Aspirator increases relief valve poppet stroke

Addition of an aspirator to a relief valve increases the valve poppet stroke under dynamic flow conditions. The aspirator allows poppet inlet dynamic forces to overcome relief valve spring force. It reduces the fluid pressure in the skirt cavity by providing a low pressure sense probe.

Biddle, M. E.↗
NASA NTRS1970

Calculation of incompressible fluid flow through cambered blades

Conformal mapping technique yields linear, approximate solutions for calculating flow of an incompressible fluid through staggered array of cambered blades for the cases of flow with partial cavitation and supercavitation. Lift and drag coefficients, cavitation number, cavity shape, and exit flow conditions can be determined.

Hsu, C. C.↗
NASA NTRS1970

Simplified computation of compressible fluid flow parameters

Mathematical techniques analyze fluid flow through circular duct, enlarged or constricted circular duct, and across an orifice or nozzle. Using subsonic Mach number as basic flow parameter, a series of working graphs displays the variation of various physical parameters in each of the flow conditions.

Beimgraben, H. W.↗
NASA NTRS1970

Visible light electroluminescent diodes of indium-gallium phosphide

Vapor deposition and acceptor impurity diffusion techniques are used to prepare indium-gallium phosphide junctions. Certain problems in preparation are overcome by altering gas flow conditions and by increasing the concentration of phosphine in the gas. A general formula is given for the alloy's composition.

Clough, R.↗