Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW VELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

On the structure of turbulent wakes and merging shear layers of multielement airfoils

The structure of the attached turbulent flow in the vicinity of a NACA 4412 airfoil equipped with a single-slotted flap was studied. The airfoil/flap configuration was tested at a Mach number of 0.06 and a Reynolds number of 1.3 x 10 to the 6th in a 7- by 10-Foot Wind Tunnel. Surface-pressure measurements were made on the main airfoil and on the flap. Detailed measurements, obtained using a high-spatial-resolution laser Doppler anemometer, were made of the mean velocity flow field and of the second-order statistical quantities (Reynolds stresses) in the boundary layers, wakes, and merging shear layers. The experimental observations are compared with theoretical predictions of pressure, mean velocity, and Reynolds stress.

Olson, L. E.↗

Factors governing sustainable groundwater pumping near a river

The objective of this paper is to provide new insights into processes affecting riverbank filtration (RBF). We consider a system with an inflatable dam installed for enhancing water production from downstream collector wells. Using a numerical model, we investigate the impact of groundwater pumping and dam operation on the hydrodynamics in the aquifer and water production. We focus our study on two processes that potentially limit water production of an RBF system: the development of an unsaturated zone and riverbed clogging. We quantify river clogging by calibrating a time-dependent riverbed permeability function based on knowledge of pumping rate, river stage, and temperature. The dynamics of the estimated riverbed permeability reflects clogging and scouring mechanisms. Our results indicate that (1) riverbed permeability is the dominant factor affecting infiltration needed for sustainable RBF production; (2) dam operation can influence pumping efficiency and prevent the development of an unsaturated zone beneath the riverbed only under conditions of sufficient riverbed permeability; (3) slow river velocity, caused by dam raising during summer months, may lead to sedimentation and deposition of fine-grained material within the riverbed, which may clog the riverbed, limiting recharge to the collector wells and contributing to the development of an unsaturated zone beneath the riverbed; and (4) higher river flow velocities, caused by dam lowering during winter storms, scour the riverbed an thus increase its permeability. These insights can be used as the basis for developing sustainable water management of a RBF system.

54 ENVIRONMENTAL SCIENCES↗

The effects of Kelvin-Helmholtz instability on resonance absorption layers in coronal loops

One of the long-standing uncertainties in the wave-resonance theory of coronal heating is the stability of the resonance layer. The wave motions in the resonance layer produce highly localized shear flows which vary sinusoidally in time with the resonance period. This configuration is potentially susceptible to the Kelvin-Helmholtz instability (KHI), which can enhance small-scale structure and turbulent broadening of shear layers on relatively rapid ideal timescales. We have investigated numerically the response of a characteristic velocity profile, derived from resonance absorption models, to finite fluid perturbations comparable to photospheric fluctuations. We find that the KHI primarily should affect long (approximately greater than 6 x 10(exp 4) km) loops where higher velocity flows (M approximately greater than 0.2) exist in resonance layers of order 100 km wide. There, the Kelvin-Helmholtz growth time is comparable to or less than the resonance quarter-period, and the potentially stabilizing magnetic effects are not felt until the instability is well past the linear growth stage. Not only is the resonance layer broadened by the KHI, but also the convective energy transport out of the resonance layer is increased, thus adding to the efficiency of the wave-resonance heating process. In shorter loops, e.g., those in bright points and compact flares, the stabilization due to the magnetic field and the high resonance frequency inhibit the growth of the Kelvin-Helmholtz instability beyond a minimal level.

Karpen, Judith T.↗

Emrgy 2022 Hydrokinetic Turbine Data - TEAMER Post Access Submission

The data herein contains all data collected and used for the Performance Characterization Testing and Model Calibration of a Vertical Axis Hydrokinetic Turbine. The data includes performance data and durability data for the Hydrokinetic Turbine. The device performance data contains shaft RPM, turbine RPM, power output, flow velocity, pressure, and pressure drop across the turbine. The mechanical durability data includes stress and strain at varied depths and velocities. There is also an FEA analysis included. This TEAMER project was awarded to Emrgy, Inc.in collaboration with Alden Research Laboratory LLC.

16 TIDAL AND WAVE POWER↗

Kinetic description of quasi-stationary axisymmetric collisionless accretion disk plasmas with arbitrary magnetic field configurations

A kinetic treatment is developed for collisionless magnetized plasmas occurring in high-temperature, low-density astrophysical accretion disks, such as are thought to be present in some radiatively inefficient accretion flows onto black holes. Quasi-stationary configurations are investigated, within the framework of a Vlasov-Maxwell description. The plasma is taken to be axisymmetric and subject to the action of slowly time-varying gravitational and electromagnetic fields. The magnetic field is assumed to be characterized by a family of locally nested but open magnetic surfaces. The slow collisionless dynamics of these plasmas is investigated, yielding a reduced gyrokinetic Vlasov equation for the kinetic distribution function. For doing this, an asymptotic quasi-stationary solution is first determined, represented by a generalized bi-Maxwellian distribution expressed in terms of the relevant adiabatic invariants. The existence of the solution is shown to depend on having suitable kinetic constraints and conditions leading to particle trapping phenomena. With this solution, one can treat temperature anisotropy, toroidal and poloidal flow velocities, and finite Larmor-radius effects. An asymptotic expansion for the distribution function permits analytic evaluation of all the relevant fluid fields. Basic theoretical features of the solution and their astrophysical implications are discussed. As an application, the possibility of describing the dynamics of slowly time-varying accretion flows and the self-generation of magnetic field by means of a ''kinetic dynamo effect'' are discussed. Both effects are shown to be related to intrinsically kinetic physical mechanisms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A current-driven resistive instability and its nonlinear effects in simulations of coaxial helicity injection in a tokamak

An instability observed in whole-device, resistive magnetohydrodynamic simulations of the driven phase of coaxial helicity injection in the National Spherical Torus eXperiment is identified as a current-driven resistive mode in an unusual geometry that transiently generates a current sheet. The mode consists of plasma flow velocity and magnetic field eddies in a tube aligned with the magnetic field at the surface of the injected magnetic flux. At low plasma temperatures (∼10–20 eV), the mode is benign, but at high temperatures (∼100 eV) its amplitude undergoes relaxation oscillations, broadening the layer of injected current and flow at the surface of the injected toroidal flux and background plasma. The poloidal-field structure is affected and the magnetic surface closure is generally prevented while the mode undergoes relaxation oscillations during injection. This study describes the mode and uses linearized numerical computations and an analytic slab model to identify the unstable mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DRIVING OUTFLOWS WITH RELATIVISTIC JETS AND THE DEPENDENCE OF ACTIVE GALACTIC NUCLEUS FEEDBACK EFFICIENCY ON INTERSTELLAR MEDIUM INHOMOGENEITY

We examine the detailed physics of the feedback mechanism by relativistic active galactic nucleus (AGN) jets interacting with a two-phase fractal interstellar medium (ISM) in the kpc-scale core of galaxies using 29 three-dimensional grid-based hydrodynamical simulations. The feedback efficiency, as measured by the amount of cloud dispersal generated by the jet-ISM interactions, is sensitive to the maximum size of clouds in the fractal cloud distribution but not to their volume filling factor. Feedback ceases to be efficient for Eddington ratios P{sub jet}/L{sub edd} {approx}< 10{sup -4}, although systems with large cloud complexes {approx}> 50 pc require jets of Eddington ratio in excess of 10{sup -2} to disperse the clouds appreciably. Based on measurements of the bubble expansion rates in our simulations, we argue that sub-grid AGN prescriptions resulting in negative feedback in cosmological simulations without a multi-phase treatment of the ISM are good approximations if the volume filling factor of warm-phase material is less than 0.1 and the cloud complexes are smaller than {approx}25 pc. We find that the acceleration of the dense embedded clouds is provided by the ram pressure of the high-velocity flow through the porous channels of the warm phase, flow that has fully entrained the shocked hot-phase gas it has swept up, and is additionally mass loaded by ablated cloud material. This mechanism transfers 10% to 40% of the jet energy to the cold and warm gas, accelerating it within a few 10 to 100 Myr to velocities that match those observed in a range of high- and low-redshift radio galaxies hosting powerful radio jets.

79 ASTRONOMY AND ASTROPHYSICS↗

Three-dimensional potential flows from functions of a 3D complex variable

Potential, or ideal, flow velocities can be found from the gradient of an harmonic function. An ordinary complex valued analytic function can be written as the sum of two real valued functions, both of which are harmonic. Thus, 2D complex valued functions serve as a source of functions that describe two-dimensional potential flows. However, this use of complex variables has been limited to two-dimensions. Recently, a new system of three-dimensional complex variables has been developed at the NASA Ames Research Center. As a step toward application of this theory to the analysis of 3D potential flow, several functions of a three-dimensional complex variable have been investigated. The results for two such functions, the 3D exponential and 3D logarithm, are presented in this paper. Potential flows found from these functions are investigated. Important characteristics of these flows fields are noted.

Kelly, Patrick↗

Meridional Flow Variations Over Three Solar Cycles - What Happened in Cycle 23?

The meridional flow speed determines the strength of the Sun s polar fields in both surface flux transport models and in flux transport dynamos. The polar fields produced during cycle 23 were half as strong as those produced in the previous two cycles. Helioseismic measurements of the meridional flow over the rising phase of cycle 23 indicated a decrease in flow velocity. This observation was used in flux transport dynamo models to predict a delayed start for cycle 24 and was consistent with weak polar fields and a slower equatorward drift of the active latitudes during cycle 23. On the other hand, the surface flux transport models require a faster meridional flow to produce the weak polar fields. We have begun measurements of the surface meridional flow by tracking the motions of weak (outside active regions) magnetic field elements in magnetograms from SOHO/MDI over cycle 23 and from NSO/Kitt Peak over cycles 21 to 23. We confirm the slowdown of the meridional flow over the rising phase of cycle 23 but find that the flow speed returned to its previous level during the declining phase of cycle 23. Furthermore, this appears to be a normal feature of the meridional flow during sunspot cycles. The flow is fast at minima and slow at maxima. The lack of a significantly different meridional flow during cycle 23 is very problematic for both surface flux transport models and flux transport dynamos.

Hathaway, David H.↗

Magnetosheath Propagation Time of Solar Wind Directional Discontinuities

Observed delays in the ground response to solar wind directional discontinuities have been explained as the result of larger than expected magnetosheath propagation times. Recently, Samsonov et al. (2017, https://doi.org/10.1002/2017GL075020) showed that the typical time for a southward interplanetary magnetic field (IMF) turning to propagate across the magnetosheath is 14 min. Here by using a combination of magnetohydrodynamic simulations, spacecraft observations, and analytic calculations, we study the dependence of the propagation time on solar wind parameters and near-magnetopause cutoff speed. Increases in the solar wind speed result in greater magnetosheath plasma flow velocities, decreases in the magnetosheath thickness and, as a result, decreases in the propagation time. Increases in the IMF strength result in increases in the magnetosheath thickness and increases in the propagation time. Both magnetohydrodynamic simulations and observations suggest that propagation times are slightly smaller for northward IMF turnings. Magnetosheath flow deceleration must be taken into account when predicting the arrival times of solar wind structures at the dayside magnetopause.

Samsonov, A. A.↗

Langmuir probe characterization of laser ablation plasmas

For laser ablation plumes that are significantly ionized, Langmuir probes have proved to be a useful tool for measuring the plume shape, ion energy distribution, and electron temperature. Typically in laser ablation plasmas the flow velocity is supersonic, which complicates the interpretation of the current-voltage probe characteristic. In this paper we describe some recent developments on the application of Langmuir probes for laser ablation plume diagnosis. We have investigated the behavior of the probe when it is orientated perpendicular, and parallel, to the plasma flow, and show how an analytical model developed for plasma immersion ion implantation, can quantitatively describe the variation of the ion current with probe bias for the case when the plasma flow is along the probe surface. The ion signal recorded by a probe in the parallel position is proportional to the ion density and the square root of the bias voltage. It is shown that the current varies as m{sub i}{sup -1/2} so that by comparing the ion signals from the parallel and perpendicular positions it is possible to estimate the mass of the ions detected. We have also determined the temporal variation of electron temperature. A planar probe oriented parallel to the plasma flow, where the ion current due to the plasma flow is eliminated, gives a more reliable measurement of T{sub e} (<0.6 eV). The measured T{sub e} is consistent with the measured ion current, which is dependent on T{sub e} when the time taken for an element of plasma to traverse the probe is longer than the time taken for the matrix ion sheath extraction phase.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Some optical and kinetic properties of the nearby interstellar gas

A model for resonant scattering of sunlight by the nearby interstellar gas is developed which takes into account the modification of a Maxwell-Boltzmann velocity distribution by a central force. While the formalism applies to both hydrogen and helium, the latter is emphasized. Theoretical line profiles and integrated emission rates for helium are compared with those of approximate models and with existing observations. As a result of this analysis, an upward revision of the bulk flow velocity of interstellar helium relative to the solar system, previously deduced from He 584-A observations, is required. Velocities of 15-20 km/s, temperatures of the order of 5000-10,000 K, and densities of the order of 0.008-0.02 per cu cm are sufficient to explain the (helium) observations. However, higher-precision measurements are required in order to place more stringent limits on the gas parameters. Calculations of the flux of interstellar helium atoms impinging on earth's upper atmosphere show that the resulting impact ionization is small compared with terrestrial processes.

Meier, R. R.↗

The swept angle retarding mass spectrometer: Initial results from the Michigan auroral probe sounding rocket

Data from a sounding rocket flight of the swept angle retarding ion mass spectrometer (SARIMS) are presented to demonstrate the capability of the instrument to make measurements of thermal ions which are differential in angle, energy, and mass. The SARIMS was flown on the Michigan auroral probe over regions characterized first by discrete auroral arcs and later by diffuse precipitation. The instrument measured the temperature, densities, and flow velocities of the ions NO(+) and O(+). Measured NO(+) densities ranged from 10 to the 5th power up to 3 x 10 to the 5th power ions/cu cm, while the measured O(+) densities were a factor of 5-10 less. Ion temperatures ranged from 0.15 up to 0.33 eV. Eastward ion flows approximately 0.5 km/sec were measured near the arcs, and the observed flow magnitude decreased markedly inside the arcs.

Reasoner, D. L.↗

Trailing edge noise prediction from measured surface pressures

Trailing edge (TE) noise is investigated for the case of a two-dimensional airfoil embedded in a uniform low Mach number flow, and the usefulness of several TE noise theories is examined by applying them to the measured data. The TE noise spectra and directivity are quantitatively determined for the case of a high Reynolds number and a fully turbulent boundary layer. Parameters include angle of attack, flow velocity and TE bluntness. Evanescent wave theories by Chase (1975) and Chandiramani (1974) are compared to the present results and show good agreement. Agreement of the near field pressure scatter phenomenon analysis with measurements implies that the basic assumptions used in the analysis are correct, i.e., the turbulent boundary layer (TBL) flow passes the trailing edge into the wake region. No hydrodynamic wake shedding activity is confirmed for the two-sided TBL flow, and a method incorporating the principles of the coherent output power method is used to determine the sound field. The near field edge scatter model is found to not only establish optimum sizing of edge treatment for noise control, but also to separate and identify the scattered field from the incident hydrodynamic field.

Brooks, T. F.↗

Designing It Smart With SIV

When research staff at NASA s Glenn Research Center developed and patented Stereo Imaging Velocimetry (SIV), the world s first three-dimensional (3-D), full-field quantitative and qualitative analysis tool to investigate flow velocities, experiments that were previously impossible became a reality. Seizing the opportunity to commercialize NASA s breakthrough invention, Digital Interface Systems (DIS), Inc., of North Olmsted, Ohio, acquired an exclusive license to market SIV, which has a range of applications from improving the aerodynamics of aircraft and automobiles to avoiding "no flow" regions in artificial hearts.

Source record↗

Effect of Vestibular Impairment on Cerebral Blood Flow Response to Dynamic Roll Tilt

Change to upright posture results in reductions in cerebral perfusion pressure due to hydrostatic pressure changes related to gravity. Since vestibular organs, specifically the otoliths, provide information on position relative to gravity, vestibular inputs may assist in adaptation to the upright posture. The goal of this study was to examine the effect of direct vestibular stimulation on cerebral blood flow (CBF). To examine the role of otolith inputs we screened 165 subjects for vestibular function and classified subjects as either normal or impaired based on ocular torsion. Ocular torsion, an indication of otolith function, was assessed during sinusoidal roll tilt of 20 degrees at 0.01 Hz (100 sec per cycle). Subjects with torsion one SD below the mean were classified as impaired while subjects one SD above the mean were considered normal. During one session subjects were placed in a chair that was sinusoidally rotated 25 degrees in the roll plane at five frequencies: 0.25 & 0.125 Hz for 80 sec, 0.0625 Hz for 160 sec and 0.03125 Hz and 0.015625 Hz for 320 sec. During testing, CBF (transcranial Doppler), blood pressure (Finapres), and end tidal CO2 (Puritan Bennet) were measured continuously. Ocular torsion was assessed from infrared images of the eyes. All rotations were done in the dark with subjects fixated on a red LED directly at the center of rotation. In the normal group, dynamic tilt resulted in significant changes in both blood pressure and cerebral blood flow velocity that was related to the frequency of stimulus. In contrast the impaired group did not show similar patterns. As expected normal subjects demonstrated significant ocular torsion that was related to stimulus frequency while impaired subjects had minimal changes. These data suggest that vestibular inputs have direct effects on cerebral blood flow regulation during dynamic tilt. Supported by NASA.

Serrador, J. M.↗

Advancing xEMU Lunar Dust Mitigation Devices

Fine, electrically charged, glass like dust particles caused significant damage to the Apollo EMU9 during lunar EVAs, identified as one of the greatest challenges to future exploration. Passive Lunar Dust Mitigation Devices (LDMD) were developed, within a SBIR Phase II, to prohibit this dust from interrupting venting space suit component operation. A Computational Fluid-Dynamics and Discrete Element Method (CFD-DEM) Simulation Tool was developed at the University of Colorado, Boulder to predict venting gas flow ability to self-clean adhered dust particles from LDMD surfaces. Lunar dust properties (i.e., adhesion and cohesion strengths) required to complete Simulation Tool analysis are relatively unknown due to considerable differences between the Earth and the Moon (i.e., gravity, humidity) and due to an absence of dust particles in their native state. Analytically determining gas flow velocity, density and direction within the fluid Boundary Layer, microns from LDMD surfaces presented a second challenge. Dusty Plasma Chamber testing is being performed at Auburn University, Auburn to observe electrostatically charged dust behavior as it adheres to LDMD prototypes and specific geometry and is then blown away by metered gas flow. Test articles were developed to offer insight into the impact of different flow geometries, surface roughness and dust removal within the gas Boundary-Layer. Observed dust behavior is currently being developed to support the CFD-DEM analysis. Many Simulation Tool analytical cases have been processed to support the intention of completing sensitivity studies to assess how different dust adherence values and Boundary Layer fluid properties impact LDMD self-cleaning effectivity.

Thomas J Stapleton↗

Adhesion and formation of microbial biofilms in complex microfluidic devices

Shewanella oneidensis is a metal reducing bacterium, which is of interest for bioremediation and clean energy applications. S. oneidensis biofilms play a critical role in several situations such as in microbial energy harvesting devices. Here, we use a microfluidic device to quantify the effects of hydrodynamics on the biofilm morphology of S. oneidensis. For different rates of fluid flow through a complex microfluidic device, we studied the spatiotemporal dynamics of biofilms, and we quantified several morphological features such as spatial distribution, cluster formation and surface coverage. We found that hydrodynamics resulted in significant differences in biofilm dynamics. The baffles in the device created regions of low and high flow in the same device. At higher flow rates, a nonuniform biofilm develops, due to unequal advection in different regions of the microchannel. However, at lower flow rates, a more uniform biofilm evolved. This depicts competition between adhesion events, growth and fluid advection. Atomic force microscopy (AFM) revealed that higher production of extra-cellular polymeric substances (EPS) occurred at higher flow velocities.

36 MATERIALS SCIENCE↗