Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Regolith Particle Erosion of Material in Aerospace Environments

This paper studies the effect of exposing thermal control S13GP:6N/LO-I white paint, Kapton flex cable, fiber optic cable, HEPA filter, and M55J graphite composite to high-velocity regolith environment that spacecraft landing on Mars are commonly exposed to. Due to the similarity between the Mars 2020 Rover design and Mars Science Laboratory design, it is expected that the Mars 2020 rover will be exposed to a similar high-speed regolith environment that the Mars Science Laboratory was exposed to. This environment is replicated to test the survivability of susceptible materials. The testing is performed at the University of Dayton Research Institute in Dayton, Ohio. The experiments expose different materials to basaltic–like particles ranging in size from approximately 40 μm to 2 cm, at velocities ranging from 19 m/s to 250 m/s, with varied particle fluxes (measured in mg/cm2). Depending on the size of the particle used, the particles can either embed in or erode the material. Posttest analysis shows that all materials tested will survive the expected environment observed during the Mars 2020 landing event. Some materials are tested to failure in order to better characterize material response. Materials that fail in some test scenarios include the paint, fiber optic cable, and the graphite composite. After being exposed to regolith, the α/ε ratio of the paint increased by ~37% due to particles embedding in the paint. Darkening of the paint can negatively affect thermal control of the rover. With high particle mass fluxes, the paint eventually degraded enough to expose the aluminum substrate. When impacted by a 1.5 cm particle traveling at 20 m/s, the fiber optic cable did not sever, but the impact did cause the cable to deform enough to crack the glass, which resulted in a significant increase in attenuation, rendering the cable unable to transmit data. The graphite composite also failed when exposed to high particle fluxes. All of the observed failures occurred for test cases above the expected landing environment with significant margin. Tests performed beyond the requirements help characterize how well these materials will survive in even more extreme environments for future missions.

Abid, Mohamed↗

Erosion of Volatiles by Micro-Meteoroid Bombardment on Ceres, and Comparison to the Moon and Mercury

Ceres, the largest reservoir of water in the main-belt, was recently visited by the Dawn spacecraft that revealed several areas bearing H2O-ice features. Independent telescopic observations showed a water exosphere of currently unknown origin. We explore the effects of meteoroid impacts on Ceres considering the topography obtained from the Dawn mission using a (Replaced: full-fledged replaced with: widely-used) micro-meteoroid model and ray-tracing techniques. Meteoroid populations with 0.01-2 mm diameters are considered. We analyze the short-term effects Ceres experiences during its current orbit as well as long-term effects over the entire precession cycle. We find the entire surface is subject to meteoroid bombardment leaving no areas in permanent shadow with respect to meteoroid influx. The equatorial parts of Ceres produce 80% more ejecta than the polar regions due to the large impact velocity of long-period comets. Mass flux, energy flux, and ejecta production vary seasonally by a factor of (Replaced: a few replaced with: 3–7) due to the inclined eccentric orbit. Compared to Mercury and the Moon, Ceres experiences significantly smaller effects of micro-meteoroid bombardment, with a total mass flux of 4.5±1.2×10(exp −17)kg m(exp −2)s(exp −1). On average Mercury is subjected to a 50× larger mass flux and generates 700× more ejecta than Ceres, while the lunar mass flux is 10× larger, and the ejecta generation is 30× larger than on Ceres. For these reasons, we find that meteoroid impacts are an unlikely candidate for the production of a water exosphere or significant excavation of surface features. The surface turnover rate from the micro-meteoroid populations considered is estimated to be 1.25 Myr on Ceres.

minor planets↗

Gas-Particle Interaction Model Development in Plume Surface Interaction Erosion and Cratering

The development of a predictive simulation capability for extra-terrestrial Plume Surface Interaction (PSI) environments is undertaken by the Fluid Dynamics Branch at NASA/MSFC under the Game Changing Development (GCD) Program funded by NASA’s Space Technology Mission Directorate (STMD). Predictive simulation capability for propulsive Martian and Lunar landing PSI requires accurate modeling of the complex high-speed plume impingement and resulting gas/particle-cloud and ejecta stream formation. Physics modeling gap analysis during formulation of the PSI project scope identified two particular phenomena of first order importance in gas-particle interactions that lacked existing modeling formulations. The first arises from the lack of models capturing the unsteady drag forces imparted on particles by the rapidly expanding supersonic compressible flow. The second addresses the fluctuating forces and dispersions imparted on both the particle and the fluid resulting from the interference and wake turbulence generated by close proximity particle clouds, dubbed the Particle Turbulent Kinetic Energy(PTKE). Their first order significance has been identified in experiments, but simulation models currently do not exist for either effect. The development of models and the eventual implementation into the Eulerian Gas-Granular Flow Solver (GGFS) simulation tools was constructed as one of four major tasks of the PSI project. In this process, data on particle kinetics and gas-particle interactions are collected from carefully designed experiments of particles embedded in jets. The effects observed in the experiments are then replicated in high-fidelity particle-resolved CFD simulations to inform the formulation of improvements to particle phase drag models for implementations in the more efficient Eulerian-Lagrangian CFD simulations. The resulting models are ultimately ported to the Eulerian-Eulerian models applied for most efficient simulations in PSI production application tools. This paper describes the activities and accomplishments of the past year in the gas-particle interaction modeling task of the PSI project.

Jeff West↗