Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The Effect of Proton Conductivity of Fe–N–C–Based Cathode on PEM Fuel cell Performance

A model–based impedance spectroscopy is used to determine proton conductivity, oxygen transport parameter, double layer capacitance and oxygen reduction reaction (ORR) Tafel slope in the Fe–N–C cathode catalyst layer (CCL) of a PEM fuel cell. Experimental spectra of two cells differing by the membrane thickness only are processed using a physics–based model for PEMFC impedance. The spectra have been measured in the range of current densities from 25 to 800 mA cm -2 . The ORR Tafel slope of both the cells shows almost linear growth with the current density. In one of the cells, the CCL proton conductivity σp strongly decays at the current density of 100 mA cm -2 ; this decay is accompanied by the step growth of the double layer capacitance. Other minor variations of proton conductivity and double layer capacitance with the cell current occur also in a counterphase; presumed origin of this effect is discussed. The oxygen diffusion coefficient in the cathode exhibits explosive growth with the cell current. We attribute this effect to formation of temperature and pressure gradients in the CCL due to strongly non–uniform distribution of ORR rate in the electrode.

25 ENERGY STORAGE↗
DOE OSTI2021

Electrochemistry of the NaI-AlBr 3 Molten Salt System: A Redox-Active, Low-Temperature Molten Salt Electrolyte

NaI-AlBr 3 is a very appealing low melting temperature (<100 °C), salt system for use as an electrochemically-active electrolyte. This system was investigated for its electrochemical and physical properties with focus to energy storage considerations. A simple phase diagram was generated; at >100 °C, lower NaI concentrations had two partially miscible liquid phases, while higher NaI concentrations had solid particles. Considering the fully molten regime, electrical conductivities were evaluated over 5–25 mol% NaI and 110 °C–140 °C. Conductivities of 6.8–38.9 mS cm −1 were observed, increasing with temperature and NaI concentration. Effective diffusion coefficients of the I − /I 3 − redox species were found to decrease with both increasing NaI concentration and increasing applied potential. Regardless, oxidation current density at 3.6 V vs Na/Na + was observed to increase with increasing NaI concentration over 5–25 mol%. Finally, the critical interface between the molten salt electrolyte and electrode materials was found to significantly affect reaction kinetics. When carbon was used instead of tungsten, an adsorbed species, most likely I 2 , blocked surface sites and significantly decreased current densities at high potentials. This study shows the NaI-AlBr 3 system offers an attractive, low-temperature molten salt electrolyte that could be useful to many applied systems, though composition and electrode material must be considered.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Potassium-Containing α-MnO 2 Nanotubes: The Impact of Hollow Regions on Electrochemistry

α-MnO 2 type materials have been studied as electrode materials in rechargeable batteries and electrocatalysts due to their 2 × 2 tunneled crystal structures capable of accommodating cations and their tunable physiochemical properties. In this study, we deliberately synthesized K + containing α-MnO 2 (K 0.9 Mn 8 O 16 ) hollow nanotubes varying the dimensions of the hollow regions and level of surface defects. The K 0.9 Mn 8 O 16 nanotube material samples have similar crystallinity, thermal stability, and average Mn oxidation state. Oxygen surface defects in the hollow regions were revealed through detailed studies using electron energy loss spectroscopy. The impact of the hollow regions and associated surface defects on the electrochemistry of K x Mn 8 O 16 were investigated using cyclic voltammetry, galvanostatic intermittent titration technique, and galvanostatic cycling. The K 0.9 Mn 8 O 16 nanotubes with a large hollow region (~30 nm) and higher level of surface defects show higher apparent lithium ion diffusion coefficients and lower polarization compared to the nanotubes with a small hollow region (~10 nm). In-situ lithiation demonstrated that the dimensions of the nanotube walls expanded, but the hollow region did not change in size as result of lithiation. Furthermore, this research demonstrates that tuning particle architecture and surface defects can positively impact functional behavior of electrochemical storage materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Transport of Ligand Coordinated Iron and Chromium through Cation-Exchange Membranes

Fluxes of negatively charged ligand-coordinated iron, Fe(CN) 6 3/4- , and chromium, CrPDTA 1/2− , through two promising commercial cation-exchange membranes, Aquivion E87–05S and Fumasep E-620(K), were measured as functions of current density. The magnitude of the partial current density reached a maximum of − 43 μ A cm −2 at the maximum applied current density magnitude of − 43 mA cm −2 for Fe(CN) 6 3/4− transport through Aquivion, or 0.1% of the total current density. Fumasep E-620(K) blocks practically all crossover of both compounds. Both membranes sorb more Fe(CN) 6 3/4− and CrPDTA 1/2− than predicted by Donnan equilibrium, and low crossover rates can be attributed mainly to slow diffusion, not charge-based rejection of co-ions. The magnitude of the diffusion coefficient appears to correlate with hydraulic permeability. Although Aquivion E87–05S and Fumasep E-620(K) have significant and observable differences in membrane crossover rates, cells built with the DI-soaked membranes offer similarly high coulombic efficiency, indicating the relatively small contribution that crossover makes to inefficiency over a single cycle.

25 ENERGY STORAGE↗
DOE OSTI2023

Comparing Theoretical Salt Concentration Profiles in a Polymer Electrolyte with Experimental Measurements using Operando Raman Spectroscopy

Concentrated solution theory has furthered our understanding of ion transport in electrolytes. This theory can be used to predict salt concentration profiles under an applied current if the transport properties of the electrolyte (conductivity ( κ ), restricted diffusion coefficient ( D ), and the cation transference number with respect to the solvent velocity ( t + 0 )), and the thermodynamic factor ( T f ) are known. In this work, we provide the first study comparing the predicted salt concentration profiles with measurements based on operando Raman spectroscopy. Concentration polarization is asymmetrical; the increase in salt concentration near the positive electrode is a factor of two greater than the decrease in salt concentration near the negative electrode. We find qualitative agreement between theory and experiment. Further work is needed to resolve the quantitative differences.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comparing Experimentally-Measured Sand’s Times with Concentrated Solution Theory Predictions in a Polymer Electrolyte

We compare the electrochemically measured Sand’s time, the time required for the cell potential to diverge when the applied current density exceeds the limiting current, with theoretical predictions for a 0.47 M poly(ethylene oxide) (5 kg mol −1 )/LiTFSI electrolyte. The theoretical predictions are made using concentrated solution theory which accounts for both concentration polarization and polymer motion, using independently measured parameters that depend on concentration, c : conductivity ( κ ), salt diffusion coefficient ( D ), cationic transference number with respect to the solvent velocity ( t + 0 ), thermodynamic factor 1 + dln f ± dln c , and partial molar volume of the salt ( V ̅ ); f ± is the mean molar activity coefficient of the salt. We find quantitative agreement between experimental data and theoretical predictions. We derive a generalized analytical expression for Sand’s time for electrolytes based on dilute solution theory. This expression correctly predicts the divergence of the Sand’s time at the limiting current, in agreement with experimental data and concentrated solution theory predictions. When the applied current is large compared to the limiting current, the analytical expression approaches the standard expression for Sand’s time used in the literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Exploring Li-Ion Transport Properties of Li 3 TiCl 6 : A Machine Learning Molecular Dynamics Study

We performed large-scale molecular dynamics simulations based on a machine-learning force field (MLFF) to investigate the Li-ion transport mechanism in cation-disordered Li 3 TiCl 6 cathode at six different temperatures, ranging from 25°C to 100°C. In this work, deep neural network method and data generated by ab − initio molecular dynamics (AIMD) simulations were deployed to build a high-fidelity MLFF. Radial distribution functions, Li-ion mean square displacements (MSD), diffusion coefficients, ionic conductivity, activation energy, and crystallographic direction-dependent migration barriers were calculated and compared with corresponding AIMD and experimental data to benchmark the accuracy of the MLFF. From MSD analysis, we captured both the self and distinct parts of Li-ion dynamics. The latter reveals that the Li-ions are involved in anti-correlation motion that was rarely reported for solid-state materials. Similarly, the self and distinct parts of Li-ion dynamics were used to determine Haven’s ratio to describe the Li-ion transport mechanism in Li 3 TiCl 6 . Obtained trajectory from molecular dynamics infers that the Li-ion transportation is mainly through interstitial hopping which was confirmed by intra- and inter-layer Li-ion displacement with respect to simulation time. Ionic conductivity (1.06 mS/cm) and activation energy (0.29eV) calculated by our simulation are highly comparable with that of experimental values. Overall, the combination of machine-learning methods and AIMD simulations explains the intricate electrochemical properties of the Li 3 TiCl 6 cathode with remarkably reduced computational time. Thus, our work strongly suggests that the deep neural network-based MLFF could be a promising method for large-scale complex materials.

Selvaraj, Selva Chandrasekaran (ORCID:000000029023↗
DOE OSTI2024

Stability of a Ni/NiF 2 Reference Electrode with a Metallic Membrane for Use in Molten Fluoride Salts

In this study, an experimental high-temperature fluoride salt reference electrode (RE) developed by HiFunda LLC was tested in molten FLiNaK at 550 °C. The high-temperature reference electrode (HTRE), based on the Ni/NiF 2 redox couple, was tested over a period of 13 d for short-term stability, long-term stability, and electrochemical analysis capabilities. The HTRE was tested using open circuit potentiometry (OCP), cyclic voltammetry (CV), square wave voltammetry (SWV), and electrochemical impedance spectroscopy (EIS). The HTRE reference potential was measured against changes in salt composition by increasing FeF 2 concentrations in the melt across six additions from 0 to 0.1 mol% FeF 2 . The long-term stability of the electrode was then tested over ten days at a constant composition of 0.1 mol% FeF 2 . OCP, SWV, and CV were used to calculate an average potential drift between 7–10 mV per day. Using CV and SWV, the number of electrons transferred for iron reduction and the diffusion coefficient of Fe 2+ were measured.

Electrochemistry↗
DOE OSTI2024

Electrochemical Reactivity of Hydrogen Storage Materials: Exploring Borohydride and Hydrazinium Salt Mixtures

Electrochemical characterization of hydrogen storage materials was conducted in a non-aqueous environment to investigate the direct electrochemical release and consumption of hydrogen and the potential for regeneration. We first address the challenge of minimal solubility of the synthetic precursors, sodium borohydride (NaBH 4 ) and hydrazinium bromide (N 2 H 5 Br), in both organic and inorganic solvents. We next determine and calibrate a reference electrode formulation compatible with our non-aqueous media and analytes that demonstrates a stable reference potential. We employ cyclic voltammetry (CV) to characterize the precursors and mixtures thereof. Each CV peak is assigned to a corresponding electrochemical reaction. Using the rate-dependent CV method and Randles–Ševčík equation, we calculate the diffusion coefficient of each chemical (NaBH 4 and N 2 H 5 Br). Analysis of the CVs, coupled with 11B NMR analysis, reveals a room temperature chemical transformation of NaBH 4 and N 2 H 5 Br mixtures into hydrazine borane (N 2 H 4 BH 3 ). These results are particularly significant, considering the limited information available on the electrochemical characterization of metal borohydride and hydrazinium salt in non-aqueous media. This work establishes a foundation for adapting a non-aqueous electrochemical system to further study the borohydride family of chemistries and to design and develop electrochemical devices for direct electrical and chemical energy interconversion with hydrogen storage materials.

08 HYDROGEN↗
DOE OSTI2024

Correlation Between Microscopic Current Fluctuations Observed at Ultra-Microelectrodes and Macroscopic Bulk Electrolysis Performance in Redox-Active Microemulsions

Microemulsions (μEs) have been proposed as redox flow battery (RFB) electrolytes that maximize ionic conductivity and charge capacity by synergizing two immiscible phases. However, charge transfer during electrolysis in μEs is poorly understood. Here, we show that ultramicroelectrode electrolysis of ferrocene-loaded μEs –20%, 60%, and 90% water - reveals stochastic current fluctuations. These are differentiated in the scanning electrochemical microscopy (SECM) geometry, where power spectral density analysis showed distinct changes in the frequency contributions. SECM in the substrate generation-tip collection mode showed that fluctuations arise under mass-transfer control. Significant differences in the diffusion coefficient of ferrocene species were deducted from SECM approach curves, suggesting phase transfer behavior. Using bulk electrolysis, we calculated the charge accessibility and cycling behavior in the μEs. A decrease in the stochastic behavior of the μEs seems to correlate to a higher accessibility and cycling performance, with the 90% water μE displaying the best reversibility and the 60% the lowest. Altogether, these results suggest that Marangoni-type convection driven by concentration gradients and/or μE restructuring during charge transfer play a role in the electrochemical performance of μEs. This presents opportunities for screening and diagnosing the performance of these emerging RFB electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2025

Toward Establishing Uniqueness of Experimentally Determined Transference Numbers

The passage of current through a battery results in the development of concentration gradients in the electrolytic phase. For a fully characterized binary electrolyte, where the conductivity, salt diffusion coefficient, cation transference number, and the thermodynamic factor are known, concentration and potential gradients in the electrolytic phase can be modeled using Newman’s concentrated solution theory. We report two methods for measuring the transference number: the standard method based on electrochemical measurements ( t + , echem 0 ) and electrophoretic NMR ( t + , eNMR 0 ). The electrochemical approach requires combining measurements from multiple experiments; the equations used to determine the cation transference number and the thermodynamic factor are coupled, nonlinear algebraic equations. In the electrophoretic-NMR-based approach, however, the equations used to determine the cation transference number and the thermodynamic factor are decoupled. We find for a liquid electrolyte comprised of a lithium salt dissolved in tetraglyme, the values of the transference numbers obtained by these two methods are distinct. For example, at 30 °C, t + , echem 0 = −1.02 ± 1.11 and t + , eNMR 0 = 0.25 ± 0.04. The corresponding thermodynamic factors are also different. While the magnitude of the predicted concentration gradients based on the two sets of parameters are different, the predicted current-voltage relationships are similar.

Hickson, Darby T. (ORCID:0000000251339755)↗
DOE OSTI2025

Choline Chloride-Based Water-in-Salt Electrolyte for Efficient Iron Electrodeposition

Electrochemical production of iron is a promising low-cost and modular approach to replace the traditional blast furnace. Aqueous electrolytes for iron electrolysis are advantageous as they can be operated at near-ambient temperatures, but they suffer from inefficiencies due to the parasitic hydrogen evolution reaction. In this work, we identify a new water-in-salt electrolyte (WiSE) based on choline chloride (ChCl) for high coulombic efficiency (>85%) iron deposition. Electrochemical analysis of the partial current densities of iron plating and hydrogen co-evolution revealed that, at optimal WiSE compositions, water reduction is kinetically suppressed resulting in an increase in the Fe plating efficiency. Decreased coordination of water and increased coordination of choline’s alcohol group with the Fe 2+ ion were observed through 1 H NMR providing evidence that water reduction is kinetically suppressed in WiSE. Additionally, Raman spectroscopy revealed that complexation effects (with Cl – ) reduce Fe 2+ diffusion coefficients and corresponding limiting currents as the ChCl concentration is increased. This results in an optimal WiSE composition (4 M ChCl + 1 M FeCl 2 ) that provides kinetic suppression of HER but also low transport resistance to Fe plating yielding 85% coulombic efficiency at high current densities.

Sinclair, Nicholas Scott [Case Western Reserve Uni↗
DOE OSTI2025

Electrochemical Characterization of Dissolved Oxides in Molten FLiNaK

Molten fluoride salts have long been the subject of investigation given their application in a variety of industrial processes. Oxides are a common exogeneous impurity within these systems, and can lead to many operational and regulatory concerns. In recent studies, the electro-oxidation of dissolved metallic oxides has been attributed to a single step oxygen evolution reaction despite voltametric evidence suggesting otherwise. Here, we first use square wave voltammetry to confirm that the oxidation of dissolved oxides in fluorides proceeds via a two-electron transfer reaction and then demonstrate that the presence of a peroxide-mediated redox reaction better explains the electrochemical data. Numerical simulations were then used to support the determination of improved diffusion coefficients to enable electroanalytical measurements of the oxide concentration across at a variety of temperatures. A linear Arrhenius relationship was observed when the experimental data was corrected for ohmic resistance effects. Concentration measurements using the corrected square wave voltammetry data demonstrated high accuracy across a large range of concentrations, while the uncorrected data showed plateauing and high errors. In total, this work serves to rectify previously misconstrued electrochemical data of oxides in molten salts and demonstrate how accurate, in situ concentration measurements can be achieved in real-world systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Graph Neural Networks and Applied Linear Algebra v.1.0

SAND2024-01365O The Graph Neural Networks and Applied Linear Algebra is companion software for the educational article with the same title. The software provides illustrative examples of graph neural networks in Matlab and Python. These stand-alone algorithms are for educational purposes. The software also includes graph neural network-based algorithms for a trainable Jacobi iteration as well as diffusion coefficient estimation. The software provides human-interpretable implementations of Graph Neural Networks in Matlab and Python. These implementations are not optimized for performance and instead emphasize readability. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

SciDAC↗
DOE OSTI2021

A novel physics-based and data-supported microstructure model for part-scale simulation of laser powder bed fusion of Ti-6Al-4V

The elasto-plastic material behavior, material strength and failure modes of metals fabricated by additive manufacturing technologies are significantly determined by the underlying process-specific microstructure evolution. In this work a novel physics-based and data-supported phenomenological microstructure model for Ti-6Al-4V is proposed that is suitable for the part-scale simulation of laser powder bed fusion processes. The model predicts spatially homogenized phase fractions of the most relevant microstructural species, namely the stable β-phase, the stable α s -phase as well as the metastable Martensite α m -phase, in a physically consistent manner. In particular, the modeled microstructure evolution, in form of diffusion-based and non-diffusional transformations, is a pure consequence of energy and mobility competitions among the different species, without the need for heuristic transformation criteria as often applied in existing models. The mathematically consistent formulation of the evolution equations in rate form renders the model suitable for the practically relevant scenario of temperature- or time-dependent diffusion coefficients, arbitrary temperature profiles, and multiple coexisting phases. Due to its physically motivated foundation, the proposed model requires only a minimal number of free parameters, which are determined in an inverse identification process considering a broad experimental data basis in form of time-temperature transformation diagrams. Subsequently, the predictive ability of the model is demonstrated by means of continuous cooling transformation diagrams, showing that experimentally observed characteristics such as critical cooling rates emerge naturally from the proposed microstructure model, instead of being enforced as heuristic transformation criteria. Eventually, the proposed model is exploited to predict the microstructure evolution for a realistic selective laser melting application scenario and for the cooling/quenching process of a Ti-6Al-4V cube of practically relevant size. Numerical results confirm experimental observations that Martensite is the dominating microstructure species in regimes of high cooling rates, e.g., due to highly localized heat sources or in near-surface domains, while a proper manipulation of the temperature field, e.g., by preheating the base-plate in selective laser melting, can suppress the formation of this metastable phase.

Inverse parameter identification↗
DOE OSTI2020

Hydraulic Properties Data Package for the E-Area Soils, Cementitious Materials, and Waste Zones–Update

Hydraulic property estimates for the soils, cementitious materials, and waste zones associated with the E-Area low-level radioactive waste disposal units have been provided to support the Performance Assessments (PA) for the E-Area Low-Level Waste Facility (LLWF). Nominal or “best estimate” hydraulic property values for use in the deterministic modeling are provided along with representations of the hydraulic property value uncertainty for use in sensitivity and uncertainty modeling. The hydraulic properties provided for each of the E-Area materials include: porosity ( η ), dry bulk density ( ρ b ), particle density (ρ p ), saturated hydraulic conductivity ( K sat ), characteristic curves (suction head, saturation, and relative permeability), and effective diffusion coefficient ( D e ). A representation of the uncertainty associated with each property, except for the characteristic curves, is provided for each material, except for the E-Area waste zones. These nominal parameter values for each of the E-Area soils, cementitious materials, and waste zones, and, where indicated, parameter uncertainty representations, are based upon the following in order of priority: Site-specific field data, Site-specific laboratory data, Similarity to material with site-specific field or laboratory data, and Literature data. Additionally, a methodology to represent long-term concrete degradation is provided. Finally, because much of the nominal hydraulic property values and uncertainty representations for the E-Area soils, cementitious materials, and waste zones are based on similarity to other materials or literature data, a methodology to prioritize additional work to better define these values and representations is outlined. Prioritization should be based on the importance of the material and/or property to the results of deterministic, sensitivity, and uncertainty modeling. This prioritization should be established through a process of sensitivity modeling. This report supersedes the previous hydraulic properties data package. Revision 1 contains clarifications, updates and corrections to text, figures and tables in a number of places in the report along with some minor editing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Research on high power, doped titanium-niobium oxide anodes

The main objective of this project is to synthesize titanium niobium oxide (TNO) that has a nanoporous structure with porous channels for rapid lithium diffusion, enabling extreme fast charging (XFC). The focus of this project is to improve the electronic conductivity and ion diffusion coefficient in TNO to achieve high capacities under extreme fast charge conditions. In addition, electrolytes with additives will be formulated to promote stable interphase formation on the NMC cathode surface to improve long cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2022

MOSCATO Development and Integration in Fiscal Year 2022

During FY21, we conducted ongoing development work for the MOSCATO (Molten Salt Chemistry and Transport) solver. The code development work primarily consisted of transitioning capabilities from the original version of the solver, which was written in OpenFOAM, into Nek5000. In doing so, a fast, highly parallelizable solver was created that is capable of complex chemistry and corrosion simulations for engineering-scale molten salt systems. The Nek5000 version of MOSCATO is now fully featured and capable of higher-fidelity simulations than were previously possible. Demonstration cases including a thermal convection loop have been simulated to test these new capabilities. We built upon the work for FY22 and improved the code from several different perspectives. First, we improved the user interface by adding a new component to the official Nek5000 input file (.par). This new part contains documents parameters like, salt properties (density, viscosity, Cp, thermal conductivity), diffusion coefficients, standard potential, etc. Second, we built a conversion script to extract salt properties from the MSTDB-TP salt database and write to MOSCATO input file. Third, we migrated the code to NekRS, which is the GPU branch of Nek5000 and suitable for next generation supercomputers. Verification and Validation (V&V) work was also continued in FY22. Two tasks were performed. The first V&V task involved the validation of the Poisson-Nernst-Planck equation solver and Butler-Volmer electrode kinetics, by comparing with numerical and experimental data about thermoelectric cells. The second task involved the comparisons to corrosion results from a thermal convection loop run during the MSRE era. Satisfactory agreement was obtained from both tasks.

Yuan, Haomin↗