Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗

Metastable formation and disordering kinetics of body-centered orthorhombic CrNi 2 laths in a Cr-Ni binary alloy

Chromium (Cr) alloys combine low density with high-temperature strength but suffer from brittleness and rapid softening. Body-centered orthorhombic (BCO) CrNi 2 laths have been shown to improve Cr-alloy high-temperature strength retention, yet their thermal stability and transformation behavior remain unclear. CrNi 2 conventionally forms through long-range ordering from a face-centered cubic (FCC) phase. Using multiscale microscopy and neutron diffraction, we show that CrNi 2 instead nucleates from a body-centered cubic (BCC) matrix, in a binary Cr 85 Ni 15 alloy. Despite aging above the equilibrium ordering temperature, CrNi 2 persists for ∼220 h at 760 °C before fully disordering, indicating sluggish transformation kinetics. The formation and decomposition follow differing transformation pathways (BCC → CrNi 2 → FCC), revealing kinetic asymmetry not captured by equilibrium Cr-Ni phase diagrams. In conclusion, these findings redefine the transformation behavior of CrNi 2 , establish its metastable kinetic window, and suggest alloying strategies to stabilize CrNi 2 for precipitation strengthening of high-temperature Cr-alloys.

CrNi2 transformation kinetics↗

Assessment of binary eutectic Ni alloys for high-temperature applications via laser remelting

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of the laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. Here, we conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.

Additive manufacturing↗

Scalable fabrication of high activity nanoporous copper powders for electrochemical CO 2 reduction via ball milling and dealloying

Electrochemical CO 2 reduction (ECR) is a promising technology to close the anthropic CO 2 circle using renewable energy to achieve carbon neutrality. Future commercialization of ECR will require the development of new catalyst synthesis routes that will allow significant upscaling of catalyst production from current research-level milligram quantities to the kilogram scale and beyond while maintaining the activity and selectivity demonstrated at the research level. Here, we report on generating and testing submicron-sized nanoporous copper (npCu) particles by using a scalable approach consisting of ball milling brittle Cu-based intermetallics followed by dealloying to add nanoporosity for high surface area. The resulting npCu particles have been tested in an industry-relevant large area (25 cm 2 ) electrolyzer platform and showed Faraday efficiencies (FE) for ethylene up to 34 % at current densities of 75–100 mA/cm 2 while keeping FE for hydrogen less than 30 %. Our results demonstrate that a combination of ball milling and dealloying is a promising approach to generate large quantities of high activity and high surface area npCu particles for ECR at an industry-relevant scale.

30 DIRECT ENERGY CONVERSION↗

Mechanical property degradation of high crystalline SiC fiber–reinforced SiC matrix composite neutron irradiated to ~100 displacements per atom

For the development of silicon carbide (SiC) materials for next-generation nuclear structural applications, degradation of material properties under intense neutron irradiation is a critical feasibility issue. This paper evaluated the mechanical properties and microstructure of a chemical vapor infiltrated SiC matrix composite, reinforced with a multi-layer SiC/pyrolytic carbon–coated Hi-Nicalon TM Type S SiC fiber, following neutron irradiation at 319 and 629 °C to ~100 displacements per atom. Both the proportional limit stress and ultimate flexural strength were significantly degraded as a result of irradiation at both temperatures. After irradiation at 319 °C, the quasi-ductile fracture behavior of the nonirradiated composite became brittle, a result that was explained by a loss of functionality of the fiber/matrix interface associated with the disappearance of the interphase due to irradiation. Finally, the specimens irradiated at 629 °C showed increased apparent failure strain because the fiber/matrix interphase was weakened by irradiation-induced partial debonding.

36 MATERIALS SCIENCE↗

Atomic force microscopy monitoring of subcritical slow crack growth in soda lime silicate glass

Prediction of brittle fracture in silicate glasses requires a fundamental understanding of slow crack growth rates, far below the critical stress intensity (K IC ) of the material. Here, in this study, atomic force microscopy (AFM) was used to characterize slow crack propagation in soda lime silicate glasses. Using large-sample AFM systems with specialized tips and scanners, fractures less than 20 nm wide were measured as a function of relative humidity (RH). The results were found to be sensitive to the type of AFM tip used and to the dryness of the surface. Continuous scanning and image capture over several days allowed the determination of the crack tip velocity. The dependance of crack tip velocity on RH was measured by enclosing the sample and AFM head in a humidity-controlled chamber. The crack tip velocity was measured as low 4.0×10 -12 m/s at 15 % RH and as high as 3.7×10 -10 m/s at 40 % RH. Overall crack growth was smooth during the AFM scan. Additionally, recession of the crack tip was noted as the sample dried, indicating crack tip closure may be occurring. Further studies on alternative compositions will provide details on subcritical fracture processes in a range of different environmental conditions.

Atomic force microscopy↗

Siloxane-modified polycarbosilane flexible Prepregs for fabrication of ceramic matrix composites via compression molding and PIP densification

For this work, the development of ceramic matrix composites (CMCs) using 5 harness satin carbon fiber fabric impregnated with commercial polycarbosilane precursor plasticized by siloxane copolymer was investigated aiming to improve wetting behavior and shape conformability. The polycarbosilane precursor and polysiloxane plasticizer were mixed at varying weight ratios to obtain flexible preceramic resin prepreg cloths. 13 plies of preceramic polymer prepreg cloths were stacked in 0/90° layup and cured by compression molding, followed by densified via PIP process. The CMCs were densified with eight PIP cycles followed by final crystallization at 1600 °C. The CMCs made with 10 wt% polysiloxane loading showed lower viscosity of the prepreg resin as well as higher strength and displacement to failure compared to those fabricated from unplasticized polycarbosilane prepolymer. In contrast, at higher concentration of plasticizer, viscosity of the prepreg resin increased, and the CMC became more brittle; however, it exhibited considerably higher thermal conductivity.

Carbosilane↗

Friction-based riveting technique for AZ31 magnesium alloy

Rivet materials used in the aerospace and automotive industries are typically alloys of aluminum (Al) or steel. Magnesium (Mg) is an attractive alternative because it is 33% and 75% lighter than Al and steel, respectively. However, a primary barrier for using Mg as rivet material is its poor formability at room temperature, resulting in brittle fracture of the rivet head during cold riveting. Hot riveting is possible but suffers from high cycle time due to the need for pre-heating. A new friction-based riveting technique, Rotating Hammer Riveting (RHR), is reported to fully form AZ31 Mg rivet heads in a mere 0.23 seconds cycle time. Heat and pressure generated through severe plastic deformation during the process was sufficient to form the Mg rivet head without the need for a separate pre-heating operation. Due to dynamic recrystallization, AZ31 Mg grains in the rivet head were significantly refined from about 15 to 2.6 µm during RHR, which favors the formability of Mg rivet by triggering grain boundary sliding and reducing plastic anisotropy of Mg. In addition, RHR joints showed a metallurgical bond between the rivet head and top sheet, which eliminates a significant pathway for corrosion.

36 MATERIALS SCIENCE↗

Friction Stir Dovetailing of AA7099 to Steel with AA6061 Interlayer for Reduced Zn Embrittlement at Dissimilar Interface

Joining of high strength Al alloy (AA7099) to steel (rolled homogeneous armor) with and without AA6061 interlayer was achieved using a friction stir dovetailing (FSD) method. Detailed investigations were conducted to establish correlations between mechanical performance and microstructural evolution of FSD joints. Lap shear tensile testing revealed that incorporation of the AA6061 interlayer combined with tailored processing methodology significantly improved both mechanical interlocking and load transmission across the dovetail interface. Following incorporation of the interlayer, the maximum load carrying capacity and peak extension (of the AA7099/AA6061/steel joint) are 60% and 210% higher, respectively, than results obtained from an AA7099/steel joint without an interlayer. Without an AA6061 interlayer, formation of zinc rich intermetallic compounds led to brittle interfacial failure of the AA7099-steel FSD joint. Incorporation of novel tool and joint configuration eliminated asymmetric joint performance as a function of loading direction, which is generally observed in friction stir lap welding. The efficacy of the use of an AA6061 interlayer in joining AA7099 to steel was demonstrated through mechanical testing as well as high resolution analytical electron microscopy characterization.

Dissimilar metal joining, Friction stir dovetailin↗

Mechanical behavior of bimetallic stainless steel and gray cast iron repairs via directed energy deposition additive manufacturing

The utility of gray cast iron in engine components remains tied to the mechanical performance and cost. Repair and remanufacturing of castings offer economical and sustainable benefits; however, high thermal input from traditional fusion-based welding is unable to restore the original mechanical quality owing to brittle microstructures and porosity formed in situ. Directed energy deposition (DED) is an additive manufacturing method that has received considerable interest for repairs owing to the highly controllable nature of the process. Despite this, few works have connected the effect of DED parameters on actual interfacial strength. Consequently, distinct DED parameter combinations were identified to maximize the strength and fatigue life of the repaired cast iron. Further, high speed melt pool imaging and residual stress measurements are provided to aid in the understanding of the metallurgical quality and strength seen in these structures. In general, higher scanning speeds and lower thermal gradients promoted comparable tensile strength to that of the original gray cast iron. The results presented here provide a foundation to tune in the DED process to generate the required mechanical quality as a starting point for future process advancements.

36 MATERIALS SCIENCE↗

Machinability comparison of additively manufactured and traditionally wrought Ti-6Al-4V alloys using single-point cutting

Post-machining is often needed to provide high dimensional accuracy and fine surface finish for additively manufactured Ti-6Al-4V (Ti64). The material inhomogeneity, such as pores and microstructures, can affect the machining behavior of this already difficult-machine alloy. This study adopts a holistic approach to compare the machinability of additively manufactured and traditionally wrought Ti64 in terms of key machining factors, including forces, temperature, and vibration and the major machining outcomes including tool life, surface finish, and dimensional accuracy. Stress-relief annealing is applied to each of the part conditions as a secondary variable to observe the additional effects. The results show that AM is not particularly more difficult to machine in terms of cutting force and temperature, but it creates high cutting vibrations across a wide range of frequencies (to and over 5 kHz). The high vibrations do not lead to worse surface finish or dimensional accuracy but tend to worsen the tool life by chipping off the cutting edge. The vibration can be attributed to the brittle martensitic microstructure found in additively manufactured Ti64, which is also evidenced by the more serrated chips. Stress-relieving is found to change the microstructure and reduce the level of vibration to that of the wrought counterpart.

36 MATERIALS SCIENCE↗

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗

Building metallic glass structures on crystalline metal substrates by laser-foil-printing additive manufacturing

In laser-foil-printing additive manufacturing, 3D metallic glass structures can be built by laser welding of amorphous foils, layer by layer, upon a crystalline metal substrate. Here, in this paper, weldability studies for laser welding of Zr 52.5 Ti 5 Al 10 Ni 14.6 Cu 17.9 amorphous foils onto a Ti-6Al-4V (Ti 6-4) or Zr 702 substrate are conducted. After laser welding, the weldments are analyzed using X-ray diffractometer, optical microscope, scanning electron microscope equipped with energy dispersive spectroscopy and micro-hardness tester. The results show that Zr 702 is a suitable substrate for Zr-based metallic glass structure since crack-free weld joints can be obtained owing to the formation of ductile α-Zr, while Ti 6-4 is not an appropriate substrate since it has high cracking susceptibility due to the formation of a large amount of hard and brittle intermetallics near the foil-substrate interface. It was found that the mixing between melted substrate and foil is not uniform but exhibits a distinct “swirl” pattern. The swirl structure is more pronounced in Ti 6-4 than in Zr 702 substrate which may contribute to its high cracking susceptibility. The aforementioned mixing leads to partial crystallization of the first amorphous layer; however, fully amorphous is achieved in the additional welding layers.

36 MATERIALS SCIENCE↗

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗

Toughening Sm–Co sintered magnets via microstructure modification with additives

We report the mechanical properties of the brittle Smsingle bondCo permanent magnets are of great practical significance. However, studies on the magnets have mostly focused on their magnetic properties. This paper reports the modified microstructure and refined unimodal grain size, enhanced flexural strength, and magnetic properties of Sm 2 (Co,Fe,Cu,Zr) 17 sintered magnets doped with La 2 O 3 , MgO, and CaF 2 fine particulates. The correlations between microstructure, phase composition, and mechanical and magnetic properties were studied. Doping of a small amount (e.g., 0.5–3 wt%) of La 2 O 3 , MgO, or CaF 2 fine particulates could significantly refine the unimodal grain sizes of the Smsingle bondCo magnets via the Zener pinning effect. Moreover, doping significantly improved the flexural strengths σ of the magnets. For example, the σ values of the magnets with 0.5 wt% MgO, 1 wt% La 2 O 3 , and 1 wt% CaF 2 were approximately 65%, 63%, and 42% higher than that of the reference magnet, respectively. Micromechanical simulations revealed that the fine particles of La 2 O 3 could deflect crack growth, while the CaF 2 particles could attract or arrest cracks during the fracture process. The mechanical strengthening effect was mainly due to grain size refinement. The Smsingle bondCo magnets with 0.5–1.5 wt% CaF2 and 0.5 wt% La 2 O 3 exhibited excellent magnetic properties while doping 1–3 wt% La2O3 and 0.5–3 wt% MgO deteriorated magnetic performance. The rational design of CaF 2 - or La 2 O 3 -doped microstructure can be an economical and effective method for producing toughened Sm–Co sintered magnets with high magnetic performance.

36 MATERIALS SCIENCE↗

In situ grain fracture mechanics during uniaxial compaction of granular solids

Grain fracture and crushing are known to influence the macroscopic mechanical behavior of granular materials and be influenced by factors such as grain composition, morphology, and microstructure. In this paper, we investigate grain fracture and crushing by combining synchrotron x-ray computed tomography and three-dimensional x-ray diffraction to study two granular samples undergoing uniaxial compaction. Our measurements provide details of grain kinematics, contacts, average intra-granular stresses, inter-particle forces, and intra-grain crystal and fracture plane orientations. Our analyses elucidate the complex nature of fracture and crushing, showing that: (1) the average stress states of grains prior to fracture vary widely in their relation to global and local trends; (2) fractured grains experience inter-particle forces and stored energies that are statistically higher than intact grains prior to fracture; (3) fracture plane orientations are primarily controlled by average intra-granular stress and contact fabric rather than the orientation of the crystal lattice; (4) the creation of new surfaces during fracture accounts for a very small portion of the energy dissipated during compaction; (5) mixing brittle and ductile grain materials alters the grain-scale fracture response. The results highlight an application of combined x-ray measurements for non-destructive in situ analysis of granular solids and provide details about grain fracture that have important implications for theory and modeling.

42 ENGINEERING↗

The effect of loading direction on the fracture behaviors of cortical bone at a dynamic loading rate

Here, the dynamic cracking processes in porcine cortical bone were visualized in real-time using the high-speed synchrotron X-ray phase-contrast imaging (PCI) technique in three osteon orientations: in-plane transverse, out-of-plane transverse and in-plane longitudinal. The dynamic flexural loading applied on the pre-notched bone specimens was introduced by a modified Kolsky compression bar. High-speed X-ray images of the entire loading events were documented with a high-speed camera. Three-dimensional X-ray micro-computed tomography was conducted to examine the intact microstructures and obtain the basic material properties of the bone material used for mechanical characterizations. The onset location, where crack initiated, and the subsequent direction, along which the incipient crack propagated, were measured quantitatively using the high-speed X-ray images and the latter was found dependent on the osteon direction significantly. The crack propagation velocities were dependent on crack extension over the entire crack path significantly for all the three directions while the initial velocity for in-plane longitudinal direction was lower than the other two directions. Straight-through crack paths were observed for in-plane longitudinal specimens while the cracks were deflected and twisted in the in-plane transverse direction. For out-of-plane transverse direction, the cracks follow paths with tortuosity fall in between the other two directions, showing a mixed mode of fractures of the former two extreme cases. The toughening mechanisms, visualized by the high-speed X-ray images, and the corresponding fracture toughness, evaluated in terms of fracture initiation toughness and crack growth resistance curve (R-curve), were also found significantly different among the three osteon directions, suggesting an overall transition from brittle to ductile-like fracture behaviors at the dynamic displacement rate (5.4 m/s) as the osteon orientation varies from in-plane longitudinal to out-of-plane transverse, and to in-plane transverse eventually.

42 ENGINEERING↗