Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vortex flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Comparison of visualized turbine endwall secondary flows and measured heat transfer patterns

Various flow visualization techniques were used to define the seondary flows near the endwall in a large heat transfer data. A comparison of the visualized flow patterns and the measured Stanton number distribution was made for cases where the inlet Reynolds number and exit Mach number were matched. Flows were visualized by using neutrally buoyant helium-filled soap bubbles, by using smoke from oil soaked cigars, and by a few techniques using permanent marker pen ink dots and synthetic wintergreen oil. Details of the horseshoe vortex and secondary flows can be directly compared with heat transfer distribution. Near the cascade entrance there is an obvious correlation between the two sets of data, but well into the passage the effect of secondary flow is not as obvious. Previously announced in STAR as N83-14435

Gaugler, R. E.↗
NASA NTRS2012

Experimental Study of Boundary Layer Flow Control Using an Array of Ramp-Shaped Vortex Generators

The objective of this study was to obtain a database on the flowfield past an array of vortex generators (VGs) in a turbulent boundary layer. All testing was carried out in a low speed wind tunnel with a flow velocity of 29 ft/sec, giving a Reynolds number of 17,500 based on the width of the VG. The flowfield generated by an array of five ramp-shaped vortex generators was examined with hot wire anemometry and smoke flow visualization. The magnitude and extent of the velocity increase near the wall, the penetration of the velocity deficit into the core flow, and the peak streamwise vorticity are examined. Influence of various parameters on the effectiveness of the array is considered on the basis of the ability to pull high momentum fluid into the near wall region.

Hirt, Stefanie M.↗
NASA NTRS1986

Water tunnel results of leading-edge vortex flap tests on a delta wing vehicle

A water tunnel flow visualization test on leading edge vortex flaps was conducted at the flow visualization facility of the NASA Ames Research Center's Dryden Flight Research Facility. The purpose of the test was to visually examine the vortex structures caused by various leading edge vortex flaps on the delta wing of an F-106 model. The vortex flaps tested were designed analytically and empirically at the NASA Langley Research Center. The three flap designs were designated as full-span gothic flap, full-span untapered flap, and part-span flap. The test was conducted at a Reynolds number of 76,000/m (25,000/ft). This low Reynolds number was used because of the 0.076-m/s (0.25-ft/s) test section flow speed necessary for high quality flow visualization. However, this low Reynolds number may have influenced the results. Of the three vortex flaps tested, the part-span flap produced what appeared to be the strongest vortex structure over the flap area. The full-span gothic flap provided the next best performance.

Delfrate, J. H.↗
NASA NTRS1982

Supersonic burning in separated flow regions

The trough vortex phenomena is used for combustion of hydrogen in a supersonic air stream. This was done in small sizes suitable for igniters in supersonic combustion ramjets so long as the boundary layer displacement thickness is less than 25% of the trough step height. A simple electric spark, properly positioned, ignites the hydrogen in the trough corner. The resulting flame is self sustaining and reignitable. Hydrogen can be injected at the base wall or immediately upstream of the trough. The hydrogen is introduced at low velocity to permit it to be drawn into the corner vortex system and thus experience a long residence time in the combustion region. The igniters can be placed on a skewed back step for angles at least up to 30 deg. without affecting the igniter performance significantly. Certain metals (platinum, copper) act catalytically to improve ignition.

Zumwalt, G. W.↗
NASA NTRS1985

Vortex motion in wall-bounded viscous flow

A factor of general interest in a broad class of wall-bounded flows is the dynamic evolution of vortical structures through the flow. The structures are three-dimensional, and an overall mathematical description of such entities has not yet been formulated. One of the objectives of the present investigation is concerned with the establishment of a framework, based on first principles, which may form a basis for more detailed analytical studies. Another aim is related to the establishment of boundary and initial conditions in numerical experiments. The mathematical framework employed involves the method of matched asymptotic expansions, and an inner solution field is constructed which consists of a two-dimensional vortical structure. The outer solution field is taken to be an otherwise undisturbed laminar two-dimensional parallel or self-similar viscous flowfield.

Gatski, T. B.↗
NASA NTRS1992

A study of the rotor wake of a small-scale rotor model in forward flight using laser light sheet flow visualization with comparisons to analytical models

An experimental investigation was conducted in the 14 by 22 ft subsonic tunnel at NASA Langley Research Center to quantify the rotor wake behind a scale model helicopter rotor in forward flight (mu = 0.15 and 0.23) at one thrust level (C sub T = 0.0064). The rotor system used in the present test consisted of a four-bladed, fully articulated hub and utilized blades of rectangular planform with a NACA-0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the flow in planes parallel and perpendicular to the freestream flow. Quantitative measurements of vortex location, vertical skew angle, and vortex particle void radius were obtained for vortices in the flow; convective velocities were obtained for blade tip vortices. Comparisons were made between the experimental results and the wake geometry generated by computational predictions. The results of these comparisons show that the interaction between wake vortex structures is an important consideration for correctly predicting the wake geometry.

Ghee, Terence A.↗
NASA NTRS2018

Computational Investigation of Nominally-Orthogonal Pneumatic Active Flow Control for High-Lift Systems

We explore the feasibility of using nominally-orthogonal jets as active aerodynamic load control for multi-element high-lift systems, and whether the nominally-orthogonal jets can offer a variety of performance improvements. These nominally-orthogonal jets inject momentum normal to the airfoil surface near the flap trailing edge, where they create a vortex that entrains flow from the opposing side and change the airfoil circulation. Lift-enhancement opportunities of trailing edge nominally-orthogonal jets have previously been studied by Malavard et al. and Blaylock et al. on single-element airfoils; however, their effect on drag was not thoroughly investigated. In this study, we investigate two- dimensional nominally-orthogonal jet effects on both lift and drag on a two-element airfoil, NLR7301. We utilize Chimera Grid Tools to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW-2 to solve for the flow field around the airfoil. We perform various computational sensitivity studies on the baseline airfoil without a jet to validate computational results against benchmark experimental data. Using a Chimera overset grid topology, we demonstrate a similar lift-enhancement effect between a nominally-orthogonal jet and a nominally-orthogonal physical tab employed at the same location on the studied airfoil. After we introduce the nominally-orthogonal jet concept, we investigate nominally-orthogonal jets with various momentum coefficient settings, C(sub µ) = 0.00 − 0.04 and present a lift-enhancement relationship ∆C(sub l) ≃ 3.59 (C(sub µ)) for this airfoil. We discuss that utilizing a nominally-orthogonal jet with C(sub µ) = 0.01 can shift the linear region of the lift curve by a ∆C(sub l) = 0.36 for the pressure side jet and by a ∆C(sub l) = −0.27 for the suction side jet. Employing a nominally-orthogonal jet is also shown effective in altering the drag. To study the impact, we carry out a drag decomposition study in the form of drag polars. We show for a given C(sub l) = 2.50, a nominally-orthogonal jet with C(sub µ) = 0.01 on the pressure and suction side of the airfoil results in 113 drag count decrements and 41 drag count increments, respectively, compared to the baseline airfoil with no jet. These results show that large and controllable changes in aerodynamic performance can be achieved by relatively small active flow control inputs using the nominally-orthogonal jets presented in this study.

Nominally-Orthogonal↗
NASA NTRS1976

Wingtip vortex dissipator for aircraft

A means for attenuating the vortex created at aircraft wingtips which consists of a retractable planar surface transverse to the airstream and attached downstream of the wingtip which creates a positive pressure gradient just downstream from the wing is presented. The positive pressure forces a break up of the rotational air flow of the vortex.

Patterson, J. C., Jr.↗
NASA NTRS1991

Time-accurate incompressible flow computations with quadrilateral velocity-pressure elements

Quadrilateral velocity-pressure elements with constant and linear pressure interpolations are examined in the context of time-accurate finite element computation of unsteady incompressible flows. These elements involve streamline-upwind/Petrov-Galerkin stabilization and are implemented in conjunction with the one-step and multi-step temporal integration of the Navier-Stokes equations. The two test cases chosen for the performance evaluation of the formulations are the standing vortex problem and flow past a circular cylinder at Reynolds number 100.

Tezduyar, T. E.↗
NASA NTRS1987

Numerical simulation of channel flow transition, resolution requirements and structure of the hairpin vortex

Three-dimensional, nonlinear numerical simulations are presented for the K-type and H-type transitions for channel flow. There are two objectives. The first is to establish firmly the resolution requirements for the various stages in the transition process. Comparisons between calculations on various grids suggest a set of guidelines for maintaining a physically meaningful calculation. The second objective is to map out the structure of the hairpin vortices which arise in K-type and H-type transitions in channel flow, to the latest stage currently feasible. Flow field details are presented for both a subcritical Reynolds number of 1500 and a supercritical Reynolds number of 8000. The diagnostics include illustrations of the vertical shear, streamwise and spanwise vorticity, helicity, vortex stretching, and vortex diffusion fields.

Krist, Steven E.↗
NASA NTRS1987

Interaction Between a Vortex and a Turbulent Boundary Layer. Part 1: Mean Flow Evolution and Turbulence Properties

An experimental study was conducted to examine the interaction between a single weak streamwise vortex and a two-dimensional turbulent boundary layer. Attention was focused on characterizing the effect of the boundary layer on the vortex, including the effects of a moderate adverse pressure gradient. Rapid growth of the vortex core was observed, and a flattening of the core shape occurred when the dimension of the core radius became comparable to the distance of the vortex center from the surface. Adverse pressure gradients caused an increase in the rate of core growth, and therefore, a stronger distortion of the core shape. Measurements of surface skin friction beneath the vortex and some of the Reynolds stresses are presented.

Westphal, Russell V.↗
NASA NTRS1979

Application of the AMI C sub l sub max prediction method to a number of airfoils

A method for calculating the flow about airfoils up to and beyond the stall is described. It is an iterative procedure between potential flow and boundary layer solutions. The separated region is modeled in the potential flow analysis using free vortex sheets which require an inner iteration to establish their shapes. The free vortex sheet length is an important parameter in the potential flow calculation. Results so far indicate a possible correlation between wake length and airfoil thickness/chord ratio. Calculated and experimental results are compared for a series of airfoils.

Dvorak, F. A.↗
NASA NTRS1980

The quasi-vortex-lattice method for wings with edge vortex separation

The aerodynamic characteristics of wings with leading-edge vortex separation were predicted using a method based on a flow model with free vortex elements which are allowed to merge into a concentrated core. The calculated pressure distribution is more accurate than that predicted by methods with discrete vortex filaments alone. In addition, the computer time is reduced approximately by half.

Pao, J. L.↗
NASA NTRS1992

Interferometry and computational studies of an oscillating airfoil compressible dynamic stall flow field

A unique comparison has been made between real time interferograms and full Navier-Stokes computations of the density field over an oscillating airfoil undergoing dynamic stall for compressible flow conditions. Good agreement was found until a dynamic stall vortex formed in the flow. Subsequent evolution of the flow field was found to be very different in the computations. The reasons for this difference have been explained in terms of the leading edge region flow physics and the refined flow modeling that needs to be used for the post-stall flow field.

Chandrasekhara, M. S.↗
NASA NTRS1996

Wake Geometry Measurements and Analytical Calculations on a Small-Scale Rotor Model

An experimental investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to quantify the rotor wake behind a scale model helicopter rotor in forward level flight at one thrust level. The rotor system in this test consisted of a four-bladed fully articulated hub with blades of rectangular planform and an NACA 0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the vortex geometry in the flow in planes parallel and perpendicular to the free-stream flow. Quantitative measurements of wake geometric proper- ties, such as vortex location, vertical skew angle, and vortex particle void radius, were obtained as well as convective velocities for blade tip vortices. Comparisons were made between experimental data and four computational method predictions of experimental tip vortex locations, vortex vertical skew angles, and wake geometries. The results of these comparisons highlight difficulties of accurate wake geometry predictions.

Ghee, Terence A.↗
NASA NTRS1989

Evolution of the Orszag-Tang vortex system in a compressible medium. I - Initial average subsonic flow

The results of fully compressible, Fourier collocation, numerical simulations of the Orszag-Tang vortex system are presented. The initial conditions for this system consist of a nonrandom, periodic field in which the magnetic and velocity field contain X points but differ in modal structure along one spatial direction. The velocity field is initially solenoidal, with the total initial pressure field consisting of the superposition of the appropriate incompressible pressure distribution upon a flat pressure field corresponding to the initial, average Mach number of the flow. In these numerical simulations, this initial Mach number is varied from 0.2-0.6. These values correspond to average plasma beta values ranging from 30.0 to 3.3, respectively. It is found that compressible effects develop within one or two Alfven transit times, as manifested in the spectra of compressible quantities such as the mass density and the nonsolenoidal flow field. These effects include (1) a retardation of growth of correlation between the magnetic field and the velocity field, (2) the emergence of compressible small-scale structure such as massive jets, and (3) bifurcation of eddies in the compressible flow field. Differences between the incompressible and compressible results tend to increase with increasing initial average Mach number.

Dahlburg, R. B.↗