Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Feedback between radiation and transport in photovoltaics

By building on the generalized Hovel model, this work develops an analytical solution to unify photon recycling, light trapping, and carrier transport in solar cells. Enhanced transport due to photon recycling diffusion is considered. While photon recycling diffusion is often negligible, it can significantly support transport in cases where charge diffusion is low but radiative efficiency is high. Next, the diffusion equation is solved to determine carrier collection for planar and textured cells. Results elucidate novel features in the external quantum efficiency (EQE) curve that occur for textured cells with high absorption and limited transport. Then, the effect of limited transport on the radiative recombination of solar cells is investigated in detail. While the traditional treatment of detailed balance uses the applied voltage to calculate a cell's radiative recombination, the present approach uses the spatially resolved quasi-Fermi-level splitting (QFLS). Further, the discrepancy between the models is shown to be inconsequential to performance for cells with low radiative recombination (Si) or with high mobilities (lowly doped GaAs). However, for cells with high radiative recombination and low mobility (highly doped GaAs, polycrystalline CdTe, and thin-film perovskites), incorporating variation in QFLS in the determination of radiative recombination can become necessary for accurate photovoltaic modeling.

14 SOLAR ENERGY↗
DOE OSTI2024

Measuring and modeling soil moisture and runoff at solar farms using a disconnected impervious surface approach

Abstract Ground‐mounted photovoltaic sites are often treated as impervious surfaces in stormwater permits. This ignores the pervious soils beneath and between solar arrays and leads to an overestimation of runoff. Our objective was to improve solar farm stormwater hydrology models by explicitly considering the disconnected impervious nature of solar design and site characteristics. Experimental sites established on utility scale solar farms in Colorado, Georgia, Minnesota, New York, and Oregon had perennial vegetative plantings with mean precipitation ranging from 40.6 to 124.5 cm, and soil texture ranging from loamy sand to clay. Soil moisture measurements were collected beneath arrays, under drip edges, and in the vegetated area between arrays at each site. Hydrus‐3D models for soil moisture and stormwater hydrology were developed that accounted for precipitation falling on solar panels, drip edge redistribution of rainfall, infiltration, and runoff in the pervious areas between solar arrays and beneath panels. Drip edge runoff averaged 3‐ to 10‐times incident precipitation at the New York and Minnesota sites, respectively. Root mean square error values between measured sub‐hourly soil moisture and predicted moisture for large measured single storm events averaged 0.029 across all five sites. Predicted runoff depths were strongly affected by precipitation depth, soil texture, soil profile depth, and soil bulk density. Runoff depths across the five experimental sites averaged 13%, 25%, and 45% of the 2‐, 10‐, and 100‐year design storm depths, clearly showing that these solar farms do not behave like impervious surfaces, but rather as disconnected impervious surfaces with substantial infiltration of runoff in the vegetated areas between and beneath solar arrays.

Agriculture↗
DOE OSTI2025

Root size and soil physicochemical properties drive microscale spatial patterns of Fe and As retention in the rice rhizosphere

Background and Aims: Radial oxygen loss from rice roots in flooded soils oxidizes and precipitates dissolved Fe(II), Mn(II), and As(III) into mixed Fe(III), Mn(III/IV), and As(V) as root plaque and in the rhizosphere soil. It is unknown how different soils and root sizes impact the spatial extent of Fe and As retention outside the root. Methods: We imaged cross-sections of 90 roots from 6 different soils using synchrotron μXRF imaging followed by k-means clustering and elliptical averaging to distinguish bulk soil, rhizosphere, plaque, and roots based on As and Fe patterns. Results: We found preferential As retention in the plaque and rhizospheres of most roots except small (< 0.45 mm) roots in silty soils with low P or high As. In contrast, clayey soils had similar As-Fe correlations across plaque, rhizosphere, and bulk soil. Large (> 0.45 mm) roots often had no oxidized rhizosphere region. We obtained an extensive dataset of 256 As and 155 Mn synchrotron μXANES measurements, which revealed that rhizosphere and plaque As was mainly inorganic As(V) and As(III), and Mn oxidation state varied between soils but not between belowground locations. Conclusion: Small roots in coarse-textured soils were less likely to have As retention in the plaque or rhizosphere compared to large roots and fine-textured soils. Furthermore, the unique and extensive data in this study provides new insight into soil and root size impacts on As retention in the rhizosphere. It is essential to investigate a representative number of samples to draw conclusions from XRF imaging.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Creep Deformation and Dynamic Grain Growth in an Interstitial-Free Steel

Dynamic grain growth is demonstrated to be much faster than static grain growth in a body-centered-cubic, interstitial-free steel sheet material at 850°C. Dynamic grain growth occurs during concurrent plastic deformation at elevated temperature, whereas static grain growth occurs during static annealing. Grain growth during steady-state plastic flow in tension at 850°C to a true strain of 0.2 at a true-strain rate of 10 -4 s -1 doubled grain size, while static annealing for the same time produced no increase in grain size. This is described as dynamic normal grain growth (DNGG) because no abnormally large grains were observed. The recrystallized microstructure of the steel demonstrated a log-normal distribution of grain sizes. DNGG produced bimodal grain size distributions that deviate from the theoretical expectation of a simple shift to larger sizes during normal growth. The bimodal distributions contained a remnant of small grains that were not consumed during grain growth. DNGG produced a crystallographic texture that is unique from both the recrystallized material and that produced by lattice rotation alone. DNGG strengthened the {111}&lang;110&rang; and {111}&lang;112&rang; components of the strong γ-fiber component in the original recrystallization texture. Lattice rotation from tensile deformation, by contrast, strengthened the α-fiber components that intersect the original γ-fiber.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Review: Magnesium Sheet Alloy Development for Room Temperature Forming

Sheet metal forming operations in the automotive industry, including stamping, flanging, bending, hemming and trimming, are dominantly done at room temperature (RT). Unfortunately, the poor RT formability of magnesium due to its hexagonal close packed (HCP) structure and generally strong texture has limited the use of these processes in high-volume automotive production. However, the formability of magnesium can be improved via fine grain structure and random texture to enable some RT forming operations. Here, this paper presents the latest magnesium alloy development and evaluation by the United States Automotive Materials Partnership (USAMP) in collaboration with its university partners. A new sheet alloy developed in a recent USAMP project, ZAXME11100 (USAMP Alloy 2 Plus), offers excellent ductility (31% tensile elongation) and RT formability (7.8 mm Erichsen Index) in solution-treated condition (T4), and a high yield strength (270 MPa) upon post-forming aging treatment (T6), promising RT forming for automotive applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling the role of local crystallographic correlations in microstructures of Ti-6Al-4V using a correlated structure visco-plastic self-consistent polycrystal plasticity formulation

This paper presents a multi-level crystal plasticity-based simulation framework for modeling mechanical response and microstructure evolution of Ti-6Al-4V with α-lath/lamellar microstructures. Here, the model is a correlated structure visco-plastic self-consistent (CS-VPSC) formulation linking three scales: a single crystals micro-scale, a lath/lamellar colony meso-scale, and a lath/lamellar aggregate macro-scale. A selected hardening law for the evolution of critical resolved shear stress per slip system used in CS-VPSC is phenomenological. However, it adjusts the resistances of basal and prismatic slip systems based on the geometry of slip transfer between adjacent lamellae. Consistent with experimental evidences, the resolved shear stress on the pyramidal slip planes is dependent not only on the stress in the direction of slip but also on the two orthogonal shear stress components and the three normal stress components (non-Schmid effects). Electron backscatter diffraction (EBSD) data in conjunction with a procedure relying on α→β phase transformation is used to construct paired variants of α-laths/lamellae satisfying their local crystallographic correlations. The procedure fits volume fractions of individual laths/lamellae with the experimental EBSD data and selects a distribution of habit planes between adjacent variants with respect to the loading direction. The simulation framework is applied to interpret the deformation behavior in tension and compression along two sample directions of Ti-6Al-4V fabricated via laser powder bed fusion. Moreover, the model is used to simulate texture evolution during rolling of the material to large strains. It is demonstrated that the model is capable of predicting plastic anisotropy/asymmetry and the concomitant texture evolution. While the model reveals a significant effect of habit plane inclination with respect to the loading direction on yield stress, the comparison of the data and model predictions shows that a random distribution of habit planes fits the flow response. It is further inferred that the tension-compression asymmetry arises from the non-Schmid effects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength, deformation, and equation of state of tungsten carbide to 66 GPa

Here, strength, texture, and equation of state of hexagonal tungsten monocarbide (WC) have been determined under quasi-hydrostatic and non-hydrostatic compression to 66 GPa using angle-dispersive X-ray diffraction in the diamond anvil cell. Quasi-hydrostatic compression in a Ne pressure medium demonstrates that nanocrystalline WC is slightly less incompressible than bulk-scale WC, with respective bulk moduli of K 0 = 377 ± 7 and 397 ± 7 GPa and pressure derivatives K 0 ’ = 3.8 ± 0.3 and 3.7 ±0.3. This decrease in incompressibility with grain size is similar to behavior observed in other ceramics. Under nonhydrostatic compression, WC supports a mean differential stress of ~12-15 GPa at plastic yielding, which occurs at ~30 GPa. Strength in WC is anisotropic, with the (001) plane supporting 29-42% higher stress than stresses calculated from mean strain. Simulations using an Elasto-ViscoPlastic Self-Consistent model indicate that strength inferred from lattice strain theory may be overestimated due to effects of plastic deformation. Plastic deformation generates a texture maximum near $\langle\bar{2}110\rangle$ in the compression orientation, initially through prismatic slip on the {$10\bar{1}0$}$\langle\bar{1}2\bar{1}0\rangle$ and {$10\bar{1}0$}$\langle0001\rangle$ slip systems, followed by activation of pyramidal slip on {$10\bar{1}1$}$\langle\bar{2}113\rangle$ at ~40-50 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simulated effects of sample size and grain neighborhood on the modeling of extreme value fatigue response

Assessing the size of representative volume elements (RVEs) for fatigue-related applications is challenging. A RVE relevant to random microstructure requires a volume of material that is sufficiently large to capture the grain/phase heterogeneity that captures all statistical moments of the distribution of the driving force for fatigue crack formation at “hot spot” grains. Consequently, the large size of a microstructure RVE required to study fatigue phenomena is largely computationally intractable and difficult to explore. A more realistic objective in this work is to systematically study, as a function of the size of a statistical sample of microstructure, trends towards convergence of the simulated distribution of driving force for fatigue crack formation. Our present work accordingly leverages the recently developed open-source PRISMS-Fatigue framework to examine the trends in convergence of extreme value distributions (EVD) of Fatigue Indicator Parameters (FIPs) in progressively larger polycrystalline microstructure realizations of FCC Al alloy 7075-T6 using crystal plasticity finite element method simulations. The results are compared to the traditional method in which ensembles of statistical volume elements (SVEs) are simulated to build up statistics intended to approximate those associated with a larger volume of material. The convergence of EVDs with increase of size of a SVE of microstructure is closely related to the extent of grain nearest neighbor (NN) interactions. Accordingly, the sensitivity of the local micromechanical response at hot spot grains is quantitatively investigated by systematically varying the orientations of NN grains. Results indicate that SVEs with cubic crystallographic texture tend towards convergence of the EVD of FIPs with tens of thousands of grains while the random and rolled textures require larger volumes. Simple relationships based on microstructure parameters (e.g., Schmid Factor, grain size, NN misorientation) do not completely correlate to fatigue hot spot grains. Finally, the sensitivity of the extreme value fatigue response at hot spot grains extends to the 3rd NN when a single neighborhood grain orientation is altered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Estimation of micro-Hall-Petch coefficients for prismatic slip system in Mg-4Al as a function of grain boundary parameters

Grain size strengthening, referred to as the Hall-Petch effect, is a common strategy to improve the yield strength of magnesium (Mg) alloys. Several experimental studies have reported that the Hall-Petch slope strongly depends on the texture of the alloy. This effect arises from altering grain boundaries (GBs) resistance to different slip systems to transfer across adjacent grains. The grain boundary barrier strength of certain grain boundaries to basal slip, referred to as basal micro-Hall-Petch, was investigated in the previous work. Here in this study, the micro-Hall-Petch coefficient values for the prismatic slip $(k^{prismatic}_{μ})$ in Mg-4Al and their correlation with the grain boundary parameters were investigated. An experimental method was developed to initiate the prismatic slip band at low-stress levels. High-resolution electron backscatter diffraction (HR-EBSD) was used to measure the residual stress tensor, from which the resolved shear stress ahead of blocked prismatic slip bands was computed for seven different grain boundaries. $(k^{prismatic}_{μ})$ values for each individual GB were calculated by coupling the stress profile information with a continuum dislocation pile-up model. The $(k^{prismatic}_{μ})$ values vary from 0.138 MPa.m 1/2 to 0.685 MPa. m 1/2 which are almost three times larger than the calculated values for the basal micro-Hall-Petch. The $(k^{prismatic}_{μ})$ values were correlated with the GB parameters, and a functional relationship depending on the two most effective angles, the angle between the traces of the slip planes on the GB plane ($\phi$) and the angle between incoming and outgoing slip directions (κ), was proposed to estimate the Hall-Petch barrier for prismatic slip system. The work provides coefficients that can be supplied as input to crystal plasticity models to couple the effect of texture and grain size effectively.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Step-loaded creep testing of Zircaloy-4 cladding at higher temperatures in the α-phase

A refined understanding of zirconium-based cladding thermomechanical performance during rapid transients is essential for enhancing the safety and operation of light-water reactors. Traditional models for zirconium alloys under accident conditions generally assume that creep dominates fuel cladding performance. Here, these historic models have largely remained unchanged and serve as the basis for safety criteria development. As the U.S. nuclear industry pursues higher burnup levels, the increased release of fission gases during transients raises the risk of cladding failure in the low-temperature hcp α-phase, making the fidelity of these models of greater importance. Creep testing was conducted from 550–700°C with 25–120 MPa applied hoop stresses to investigate Zircaloy-4 deformation at accident-relevant temperatures in the α-phase. Step-loading was employed to capture creep behavior across a wide stress range from a single sample. The stress-strain rate data at higher temperatures (650 and 700°C) were well-described by isotropic versions of the Erbacher and Kaddour models, while the lower temperature data (550 and 600°C) were underpredicted by both anisotropic and isotropic model variants. Greater strain rates during the initial loading step at 650 and 700°C were attributed to recrystallization and grain growth of sub-micron crystallites. Yet, texture analysis revealed the basal split texture remained after testing. These observations produced results suggesting Zircaloy-4 claddings experience higher creep rates across the α-phase than previously thought, possibly related to dynamic anisotropy due to temperature dependent activation of deformation mechanisms, effects of biaxial loading, and variation in material condition between the current testing used in previous model development.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗
DOE OSTI2023

Ultrafine-grained Fe-TiB 2 high-modulus nanocomposite steel with high strength and isotropic mechanical properties by laser powder bed fusion

Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of size, geometry, and testing temperature on additively manufactured Ti-6Al-4V titanium alloy

This article presents a comprehensive study concerning size and geometry effect on the ambient and high-temperature mechanical behavior of additively manufactured laser powder bed fusion Ti-6Al-4V alloy. Key mechanical property metrics are presented, including strain hardening rate, yield strength, and Young’s modulus as a function of thickness and testing temperature (ambient, 250 °C, and 450 °C). Here, the effect of specimen size on manufacturing-induced microstructural feature formation is demonstrated and discussed. A detailed analysis regarding Young’s modulus, yield strength, and strain hardening rate variation at elevated temperatures is also presented. Size effect and temperature-sensitive deformation mechanisms are linked to the underlying microstructural deformation mechanisms activated at respective temperatures. Counter-intuitively, this study determined that irrespective of the geometry, strain hardening rates increased as temperature increased. An in-depth microstructural examination is presented to explain the stated observation. The texture of Interrupted tensile test samples examined for ambient, 250 °C, and 450 °C post-yield was observed to be unchanged, indicating the strain hardening behavior was not texture dependent. Schmid factor analysis, coupled with experimental findings from previous work, was implemented to generate a hypothesis. This hypothesis suggests that the drop in critical resolved shear stress for basal and pyramidal slip systems, as temperature increases, paired with the high dislocation density of laser powder bed fusion Ti-6Al-4V, leads to dislocation entanglement and results in increased strain hardening at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Soybean fallow and nitrification inhibitors: Strategies to reduce N 2 O emission intensities and N losses in Australian sugarcane cropping systems

The Australian sugar industry is facing mounting pressure to reduce the nitrogen (N) losses and nitrous oxide (N 2 O) emissions associated with N fertiliser use. Research has shown that N 2 O emissions from sugarcane (Saccharum officinarum L.) cropping systems can be reduced with the use of fertilisers coated with nitrification inhibitors, or by sowing legume crops in the fallows between sugarcane crop cycles. However, the efficacy of these two N management strategies across different climatic zones is still unclear, as results from field studies have been contradictory. The objectives of this study were therefore to use the DayCent model to assess the long-term effects of the two strategies (separately or in combination) on N 2 O emissions, N losses and yields. The model was parameterised using data from eight field experiments (39 treatments) conducted across four of the five main districts of the Australian sugarcane industry. A series of long-term scenarios embracing a range of N fertiliser rates (0- 160 kg N ha -1 applied as urea), climatic regions (Tropics and Subtropics), soil textures (fine- and coarse-textured soils) and N-loss risk scenarios (crop fertilised well before or close to the on-set of the wet season) were tested for both N management strategies. Simulations identified that the combined use of soybean (Glycine max L.) fallows and N fertiliser coated with the 3,4-dimethylpyrazole phosphate (DMPP) nitrification inhibitor was the most effective strategy to maintain or even increase current yields while significantly reducing N 2 O and cumulative N (mainly due to nitrate) losses. When used alone, the soybean fallow strategy on average reduced N losses over the entire crop cycle by 29 % compared with current industry best practice. However, this strategy showed a limited capacity to reduce N 2 O emissions over the entire cane crop cycle (median: -3% compared with current industry best practice), or even increased them in scenarios at high-risk of N losses in the Tropics. The use of urea coated with DMPP alone allowed current fertiliser N rates to be reduced by 30 % without any substantial yield penalty. In environments prone to high N losses, DMPP urea abated overall N losses and N 2 O emissions by 41 % and 30 %, respectively. This was the first study to use such an extensive dataset to parameterise a biogeochemical model for yields, N 2 O emissions and N losses in sugarcane cropping systems. Finally, the findings will be instrumental in guiding future research and policies designed to improve the profitability and environmental sustainability of this industry.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Simulation of radiation damage via alpha decay in BFS:PC grouts using 4 He 2+ ion acceleration

The impact of alpha radiation on cements used to encapsulate intermediate-level waste (ILW) is not well understood. ILW wastes can contain high levels of alpha-emitting radionuclides, meaning that the grouts used to encapsulate them are exposed to significant ionising radiation. Thus, a damaged region could develop in the grout adjacent to the alpha-emitting species. This work attempted to recreate this behaviour through nonradioactive 4 He 2+ ion-accelerator experiments, which have not previously been applied to common encapsulation grouts. The influence of this irradiation on a slag-Portland cement was investigated at different ages via transmission electron microscopy energy-dispersive x-ray spectroscopy (TEM-EDX) and supporting techniques, to assess whether 4 He 2+ irradiation caused textural or chemical zonation. No significant changes in hydrate phases or textures were observed, other than minor variations associated with carbonation. This paper provides a proof of concept for using ion acceleration techniques on cements and furthers knowledge on their radiation response.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shifting modes of iron sulfidization at the onset of OAE-2 drive regional shifts in pyrite δ 34 S records

We report total reduced inorganic S isotope ratios (δ 34 S CRS ) shift toward more negative values across much of the southern North Atlantic just before the onset of the Cenomanian-Turonian Ocean Anoxic Event (OAE-2). At the same time, there is no parallel isotopic change in the significantly larger pool of kerogen (organic) S, which indicates that the distribution and S-isotope composition of sulfide in the environment likely did not drive the change in δ 34 S CRS . Here, we investigate possible explanations for the negative shift in δ 34 S CRS values and their divergence from organic S by isolating iron sulfides for morphological identification and grain-specific isotopic analysis using secondary ion mass spectrometry (SIMS). In pre- and syn-OAE-2 sedimentary rocks from Demerara Rise, we find four distinct morphologies of iron sulfides: pyrite framboids (1–20 μm diameter), irregular pyrite aggregates (1–38 μm diameter), large cemented pyrite aggregates (~60 μm diameter), and irregular and cemented aggregates of the pyrite polymorph marcasite (1–45 μm diameter). These different textural groups have distinct S-isotopic compositions that are largely consistent through the onset of OAE-2. As such, the secular change in bulk δ 34 S CRS values likely reflects the changing proportions of these phases stratigraphically across OAE-2. All textural groups feature resolvable intra-grain δ 34 S variability, suggesting that the environments in which they formed were characterized by dynamic sulfide δ 34 S values and/or by partial closed-system distillation. We use grain-specific δ 34 S distributions to rule out shoaling of the chemocline within the sediments as a mechanism for the observed decrease in δ 34 S CRS . Instead, we propose that changes in the reactivity of the iron species delivered to Demerara Rise over the ~200 kyr leading up to the onset of OAE-2 impacted the relative contributions of pyrite with S-isotope signatures reflecting the water column, shallow sediments, and deeper sediments to the bulk sedimentary δ 34 S CRS value. Specifically, the change in iron reactivity at the onset of OAE-2 favored the production of 34 S-depleted large, cemented aggregates and framboids at the expense of more 34 S-enriched irregular aggregates. Our results underscore that bulk δ 34 S CRS measurements integrate multiple reduced phases that form via distinct reaction mechanisms and potentially in different parts of the depositional environment. Grain-specific SIMS analyses dramatically enrich our ability to interpret pyrite isotopic patterns in the geologic record.

58 GEOSCIENCES↗