Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test procedure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Microhardness of carbon-doped (111) p-type Czochralski silicon

The effect of carbon on (111) p-type Czochralski silicon is examined. The preparation of the silicon and microhardness test procedures are described, and the equation used to determine microhardness from indentations in the silicon wafers is presented. The results indicate that as the carbon concentration in the silicon increases the microhardness increases. The linear increase in microhardness is the result of carbon hindering dislocation motion, and the effect of temperature on silicon deformation and dislocation mobility is explained. The measured microhardness was compared with an analysis which is based on dislocation pinning by carbon; a good correlation was observed. The Labusch model for the effect of pinning sites on dislocation motion is given.

Danyluk, S.↗
NASA NTRS1985

Closure of fatigue cracks at high strains

Experiments were conducted on smooth specimens to study the closure behavior of short cracks at high cyclic strains under completely reversed cycling. Testing procedures and methodology, and closure measurement techniques, are described in detail. The strain levels chosen for the study cover from predominantly elastic to grossly plastic strains. Crack closure measurements are made at different crack lengths. The study reveals that, at high strains, cracks close only as the lowest stress level in the cycle is approached. The crack opening is observed to occur in the compressive part of the loading cycle. The applied stress needed to open a short crack under high strain is found to be less than for cracks under small scale yielding. For increased plastic deformations, the value of sigma sub op/sigma sub max is observed to decrease and approaches the value of R. Comparison of the experimental results with existing analysis is made and indicates the limitations of the small scale yielding approach where gross plastic deformation behavior occurs.

Iyyer, N. S.↗
NASA NTRS1985

Reliability analysis

The objective was to search for and demonstrate approaches and concepts for fast wafer probe tests of mechanisms affecting the reliability of MOS technology and, based on these, develop and optimize test chips and test procedures. Progress is reported on four important wafer-level reliability problems: gate-oxide radiation hardness; hot-electron effects; time-dependence dielectric breakdown; and electromigration.

Source record↗
NASA NTRS1984

Flight determination of the aerodynamic stability and control characteristics of the NASA SGS 1-36 sailplane in the conventional and deep stall angles-of-attack of between -5 and 75 degrees

The flight test procedure and the preliminary analysis of the results obtained from twenty manned flights of the SGS 1-36 in the high angles of attack Deep Stall region are discussed. A comparison of the flight determined stability and control derivatives, those of the wind tunnel, and the estimated aerodynamic data is also presented. Furthermore, deep stall dynamics response of the SGS 1-36 is discussed briefly to explain some of the unexpected flight observations.

Mahdavi, F. A.↗
NASA NTRS1985

Can pilots time-share better than non-pilots?

The time-sharing ability of 12 male pilots and 12 male college students ranging in age from 18-36 are evaluated and compared. The subjects performed five pairs of dual tasks with varying degrees of structural similarity; the test procedures are described. The time-sharing efficiency and resource allocation optimality of the subjects are analyzed. The data reveal that the pilots and students display similar time-sharing performance; the degree of time-sharing efficiency decreases and resource allocation optimality increases with an increasing degree of structural similarity between the time-shared tasks.

Tsang, P. S.↗
NASA NTRS1985

Rule-based analysis of pilot decisions

The application of the rule identification technique to the analysis of human performance data is proposed. The relation between the language and identifiable consistencies is discussed. The advantages of production system models for the description of complex human behavior are studied. The use of a Monte Carlo significance testing procedure to assure the validity of the rule identification is examined. An example of the rule-based analysis of Palmer's (1983) data is presented.

Lewis, C. M.↗
NASA NTRS1987

Flight Research on a Forward-Swept-Wing Airplane

Tests yield information relating to design, safety, and performance. Report gives overview of flight research program on X-29A experimental airplane. X-29A features forward-swept wings. Research program providing data needed to improve design, fabrications, and testing procedures for airplane.

Sefic, Walter J.↗
NASA NTRS1984

Constitutive modeling for isotropic materials

The unified constitutive theories for application to typical isotropic cast nickel base supperalloys used for air-cooled turbine blades were evaluated. The specific modeling aspects evaluated were: uniaxial, monotonic, cyclic, creep, relaxation, multiaxial, notch, and thermomechanical behavior. Further development of the constitutive theories to model thermal history effects, refinement of the material test procedures, evaluation of coating effects, and verification of the models in an alternate material will be accomplished in a follow-on for this base program.

Ramaswamy, V. G.↗
NASA NTRS1987

Low speed wind tunnel test of a propulsive wing/canard concept in the STOL configuration. Volume 1: Test description and discussion of results

A propulsive wing/canard model was tested at STOL operating conditions in the NASA Langley Research Center 4 x 7 meter wind tunnel. Longitudinal and lateral/directional aerodynamic characteristics were measured for various flap deflections, angles of attack and sideslip, and blowing coefficients. Testing was conducted for several model heights to determine ground proximity effects on the aerodynamic characteristics. Flow field surveys of local flow angles and velocities were performed behind both the canard and the wing. This is volume 1 of a 2 volume report. The model, instrumentation, and test procedures are described. An analysis of the data is included.

Stewart, V. R.↗
NASA NTRS1987

Concentrator hot-spot testing, phase 1

Results of a study to determine the hot-spot susceptibility of concentrator cells, to provide a hot-spot qualification test for concentrator modules, and to provide guidelines for reducing hot-spot susceptibility are presented. Hot-spot heating occurs in a photovoltaic module when the short-circuit current of a cell is lower than the string operating current forcing the cell into reverse bias with a concurrent power dissipation. Although the basis for the concentrator module hot-spot qualification test is the test developed for flat-plate modules, issues, such as providing cell illumination, introduce additional complexities into the testing procedure. The same general guidelines apply for protecting concentrator modules from hot-spot stressing as apply to flat-plate modules. Therefore, recommendations are made on the number of bypass diodes required per given number of series cells per module or source circuit. In addition, a new method for determining the cell temperature in the laboratory or in the field is discussed.

Gonzalez, C. C.↗
NASA NTRS1986

Development and evaluation of a fault-tolerant multiprocessor (FTMP) computer

The design, development, and testing of FTMP hardware and software for use in advanced NASA vehicles are described in three previously published reports prepared for NASA. Consideration is given to the overall FTMP architecture; the system bus; the regional design and operation of processor, slave, clock-generation, and power systems; and the FTMP executive, facilities, acceptance-test/diagnostic, applications, and support softwar. Also included are a summary of test procedures and results and an executive summary characterizing the system, the reliability and availability models, and the overall performance.

Smith, T. B., III↗
NASA NTRS1986

The other side of the safety coin

The development, inspection and testing requirements for successful production and launch and safe operation of spaceflight hardware are discussed. Emphasis is placed on paying acute attention to malfunctions, which could be caused by contaminants (particles in docking rings), insufficiently durable materials (Orbiter brakes), etc. Generic and specific problems which occur in propulsion, avionics, mechanical and computer systems and in configuration management, manufacturing and process control efforts are explored. Case histories of deficiencies found in LOX fuel lines, contaminated hydraulic control systems, the Solar Maximum Mission thermal insulation grommets, are summarized. Thorough inspection and testing procedures and design change recording during manufacture of spacecraft components are identified as requisites for successful space missions.

Roth, Gilbert L.↗
NASA NTRS1987

Further development of the losipescu shear test method

Recent activities by the present investigators to further develop the losipescu-shear-test method for use with composite materials are summarized. Finite-element analyses used to predict the stress states in the specimen are described, with particular emphasis on how they are influenced by the specific test-fixture configuration used. These same analytical tools were also used to predict the influence of specimen notch depth, notch angle, and notch-root radius. The result was a redesign of the original Wyoming version of the losipescu-shear-test fixture, and the establishment of guidelines for preparing specimens. These are discussed in some detail. Many references to available literature are included. An attempt has been made to put the work performed to date into perspective, to aid the potential user of the losipescu-shear-test method in establishing proper test procedures.

Adams, D. F.↗
NASA NTRS1987

Charge-coupled-device response to electron beam energies of less than 1 keV up to 20 keV

Recent developments of backside treatment for the backside-illuminated scientifc CCD imagers have shown near-theoretical efficiency even at the short wavelength region of the spectrum. By using SEM performance comparisons of backside-treated and untreated CCDs to an electron flux varying from 1 to 100 pA and beam energy ranging from less than 1 keV up to 20 keV are obtained. The theoretical analysis, the SEM testing procedure, and the quantum efficiency measurement results are presented. It is shown, for example, that the average quantum efficiency increases from less than 1 percent for an untreated CCD to nearly 40 percent for a backside-treated CCD at a beam energy of 1 kev.

Daud, Taher↗
NASA NTRS1987

An algorithmic approach to crustal deformation analysis

In recent years the analysis of crustal deformation measurements has become important as a result of current improvements in geodetic methods and an increasing amount of theoretical and observational data provided by several earth sciences. A first-generation data analysis algorithm which combines a priori information with current geodetic measurements was proposed. Relevant methods which can be used in the algorithm were discussed. Prior information is the unifying feature of this algorithm. Some of the problems which may arise through the use of a priori information in the analysis were indicated and preventive measures were demonstrated. The first step in the algorithm is the optimal design of deformation networks. The second step in the algorithm identifies the descriptive model of the deformation field. The final step in the algorithm is the improved estimation of deformation parameters. Although deformation parameters are estimated in the process of model discrimination, they can further be improved by the use of a priori information about them. According to the proposed algorithm this information must first be tested against the estimates calculated using the sample data only. Null-hypothesis testing procedures were developed for this purpose. Six different estimators which employ a priori information were examined. Emphasis was put on the case when the prior information is wrong and analytical expressions for possible improvements under incompatible prior information were derived.

Iz, Huseyin Baki↗
NASA NTRS1986

Full-envelope aerodynamic modeling of the Harrier aircraft

A project to identify a full-envelope model of the YAV-8B Harrier using flight-test and parameter identification techniques is described. As part of the research in advanced control and display concepts for V/STOL aircraft, a full-envelope aerodynamic model of the Harrier is identified, using mathematical model structures and parameter identification methods. A global-polynomial model structure is also used as a basis for the identification of the YAV-8B aerodynamic model. State estimation methods are used to ensure flight data consistency prior to parameter identification.Equation-error methods are used to identify model parameters. A fixed-base simulator is used extensively to develop flight test procedures and to validate parameter identification software. Using simple flight maneuvers, a simulated data set was created covering the YAV-8B flight envelope from about 0.3 to 0.7 Mach and about -5 to 15 deg angle of attack. A singular value decomposition implementation of the equation-error approach produced good parameter estimates based on this simulated data set.

Mcnally, B. David↗
NASA NTRS1986

Hydroburst test of a carbon-carbon involute exit cone

A hydroburst test of the aft portion of the PAM-D exit cone and the test procedure are described in detail. The hydrostatic pressure required to buckle the cone was 9.75 psi. Meanwhile, the PAM-D exit cone was modeled using the finite element method and a theoretical bucking pressure (8.76 psi) was predicted using the SPAR finite element code. The modeling technique employed is discussed. By comparing the theoretical to predicted critical pressures, this report verifies the modeling technique and calculates a material knockdown factor for the carbon-carbon exit cone.

Sullivan, Roy M.↗