Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

An Agrobacterium strain auxotrophic for methionine is useful for switchgrass transformation

Abstract Auxotrophic strains of Agrobacterium tumefaciens can contribute to the development of more efficient transformation systems, especially for crops historically considered recalcitrant. Homologous recombination was used to derive methionine auxotrophs of two common A. tumefaciens strains, LBA4404 and EHA105. The EHA105 strains were more efficient for switchgrass transformation, while both the EHA105 and LBA4404 strains worked equally well for the rice control. Event quality, as measured by transgene copy number, was not affected by auxotrophy, but was higher for the LBA4404 strains than the EHA105 strains. Ultimately, the use of auxotrophs reduced bacterial overgrowth during co-cultivation and decreased the need for antibiotics.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

Residual Strain Analysis in Linear Friction Welds of Similar and Dissimilar Titanium Alloys Using Energy Dispersive X-ray Diffraction

Residual strains in linear friction welds (LFW) of similar, Ti-6Al-4V (Ti64) welded to Ti-6Al-4V, and dissimilar, Ti-6Al-4V welded to Ti-5Al-5V-5Mo-3Cr (Ti5553), titanium alloys have been characterized using energy-dispersive X-ray diffraction. For each type of LFW, one sample was chosen in the as-welded (AW) condition and another sample was selected after a post-weld heat treatment (HT). Residual strains have been separately studied in the alpha and beta phases of the material, and five components (three axial and two shear) have been reported in each case. In-plane axial components of the residual strains show a smooth and symmetric behavior about the weld center for the Ti64-Ti64 LFW samples in the AW condition, whereas these components in the Ti64-Ti5553 LFW sample show a symmetric trend with jump discontinuities. Such jump discontinuities, observed in both the AW and HT conditions of the Ti64-Ti5553 samples, suggest different strain-free lattice parameters in the weld region and the parent material, whereas the results from the Ti64-Ti64 LFW samples in both AW and HT conditions suggest nearly uniform strain-free lattice parameters throughout the weld region. Finally, the observed trends in the in-plane axial residual strain components have been rationalized by the corresponding microstructural changes and variations across the weld region via backscatter electron (BSE) images.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Transmission Electron Microscope In Situ Straining Technique to Directly Observe Defects and Interfaces During Deformation in Magnesium

In-situ straining was used to study deformation behavior of hexagonal close-packed (hcp) metals.Twinning and dislocation motion, both essential to plasticity in hcp materials, were observed.Typically, these processes are characterized post-mortem by examining remnant microstructural features after straining has occurred. By imposing deformation during imaging, direct observation of active deformation mechanisms is possible. This work focuses on straining of structural metals in a transmission electron microscope (TEM), and a recently developed technique that utilizes familiar procedures and equipment to increase ease of experiments. In-situ straining in a TEM presents several advantages over conventional post-mortem characterization, most notably time-resolution of deformation and streamlined identification of active deformation mechanisms. Drawbacks to the technique and applicability to other studies are also addressed. In-situ straining is used to study twin boundary motion in hcp magnesium. A {101¯2} twin was observed during tensile and compressive loading. Twin-dislocation interactions are directly observed. Notably, dislocations are observed to remain mobile, even after multiple interactions with twin boundaries, a result which suggests that Basinki’s dislocation transformation mechanism by twinning is not present in hcp metals. The coupling of in-situ straining with traditional post-mortem characterization yields more detailed information about material behavior during deformation than either technique alone.

magnesium↗
DOE OSTI2020

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Shape-preserving machining produces gradient nanolaminate medium entropy alloys with high strain hardening capability

A high density of grain boundaries can potentially increase structural materials' strength, but at the expense of losing the materials' strain hardening ability at high flow stress levels. However, endowing materials with grain size gradients and a high density of internal interfaces can simultaneously increase the strength and strain hardening ability. This applies particularly for through-thickness gradients of nanoscale interface structures. In this work, we apply a machining method that produces metals with nanoscale interface gradients. Conventional bulk plastic deformation such as rolling, a process applied annually to about 2 billion tons of material, aims to reduce the metal thickness. We have modified this process by introducing severe strain path changes, realized by leading the sheet through a U-turn while preserving its shape, an approach known as ‘hard turning’. Furthermore, we applied this process at both room temperature and 77 K to a NiCrCo medium entropy alloy. Micropillar compression was conducted to evaluate the mechanical response. After hard turning at room temperature, the surface microstructure obtained a ~50% increase in yield stress (0.9 GPa) over the original state with homogeneous grain size (0.4 GPa), but the initial strain hardening rate did not show significant improvement. However, after hard turning at 77 k, the gradient nanolaminate structure tripled in yield stress and more than doubled its initial strain hardening rate. The improvements were achieved by introducing a specific microstructure that consists of gradient nanolaminates in the form of nanospaced twins and martensite in the face center cubic (fcc) phase. This microstructure was formed only at cryogenic temperature. It was found after turning at room temperature that only nanospaced twins were present in the fcc phase inside nanolaminates that had formed at the surface. The origin of the enhanced strain hardening mechanism was studied. Joint density functional theory (DFT) and axial next nearest neighbor Ising (ANNNI) models were used to explain the temperature-dependent phase formation of the NiCrCo nanolaminate at the surface of the hard-turned material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Lead tolerance and bioremoval by four strains of green algae from Nigerian fish ponds

Heavy metals from industry pose threats to human and environmental health. Microalgae are prime candidates to remove heavy metals from water and soil due to their metal-binding affinities, high growth rates, and contamination tolerance. Strain selection and composition of resulting contaminated biomass must be considered for downstream processing. In this study, we assessed the ability of four microalgae strains (Chlorophyceae) that were isolated from contaminated Nigerian fish ponds to take up dissolved lead at environmentally relevant concentrations (<0.05 mg L -1 – WHO standard). In a microplate assay, all strains grew in the presence of lead, tolerating concentrations up to 60 ppm, though the addition of dissolved lead affected the growth of the four strains. In a photobioreactor assay, all strains demonstrated the ability to take up dissolved lead, with removal efficiencies ranging from 86 to 93%. The concentrations of lead in contaminated biomass, removal efficiencies, and bioconcentration factors were greatest in one of the isolates Chlorella sp. MOW 12. Our results reinforce the fact that live microalgae have a greater biosorption capacity. Lead recovery from freeze-dried biomass using five different reagents showed that a 0.1 M hydrochloric acid solution was the most effective, with 83.4% recovery. We also showed that presence of lead in the culture medium resulted in an increase in the quantity of protein in the biomass. Elemental analysis of lead-bound biomass showed an increase in elements including boron and copper and a decrease in cobalt and sodium. Synergystic and antagonystic effect in uptake of other elements was strain specific, suggesting the possibility of tailored wastewater treatments depending on specific requirements.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

SlyD-deficient Escherichia coli strains: A highway to contaminant-free protein extraction

Highlights: • Ε.coli ΔSlyD/SlyX strains engineered using λ-red mediated chromosomal deletion. • Development of several bacterial strains extends the spectrum of target proteins. • Preparation of SlyD/SlyX-free target protein after one purification step only. • ΔSlyD/SlyX bacterial strains allow to obtain a fully functional protein. Binding of native bacterial protein SlyD to metal affinity matrices remains a major problem in affinity purification of His-tagged recombinant proteins from Escherichia coli cells. In this study, four novel E. coli strains that lack the expression of SlyD/SlyX, were engineered using λ-red mediated chromosomal deletion. The resultant mutant E. coli strains allow us to obtain SlyD-free proteins immediately after metal affinity chromatography, and eliminate additional purification processes. As a model protein, bispecific antibodies composed of anti-F4/80 V{sub H}H module and anti-TNF V{sub H}H module (MYSTI-2) were used. Using this protein we have shown that the SlyD/SlyX-deficient E. coli strains allow us to obtain a fully functional protein.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Predicting non-linear stress–strain response of mesostructured cellular materials using supervised autoencoder

Recent breakthroughs in advanced manufacturing capabilities have made it possible to design and print sophisticated topologies of cellular structures using diverse engineering materials such as metals, polymers, and ceramics. In these architectured materials, it is often desirable to tailor the mechanical properties by altering the unit cell topology. This necessitates an in-depth understanding of how the topology of the unit cell structure affects the macroscopic behavior of the material in both the linear and the non-linear regimes encountered under large compression. Here, we have developed a machine learning (ML) approach capable of accelerating the prediction of the stress–strain response of a polymer-based cellular structure under uniaxial confined compression. As part of generating the training data for ML, 60,000 mesostructures were generated using a relatively novel approach based on cellular automata, and their corresponding stress–strain responses were obtained from the finite element simulations. Principal component analysis (PCA) was used to reduce the dimensionality of the stress–strain curves. With only 20 principal components, PCA captured 99.89% of the variance in the stress–strain curves while reducing the dimensionality by 5X. ML using supervised autoencoder was able to successfully speed up the prediction of the non-linear stress–strain response of a unit cell by up to 4600X. The proposed method can serve as an efficient data generation tool and a rapid means for predicting the structure–property relationship through accelerated forward modeling of cellular materials under compaction, in cases where the macroscopic stress–strain response is governed by the unit-cell topology.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the correlation between plastic strain and misorientation in polycrystalline body-centered-cubic microstructures with an emphasis on the grain size, loading history, and crystallographic orientation

In this work, the correlation between plastic strain and crystallographic misorientation, grain size, grain orientation, distance from grain boundary, and loading history were investigated experimentally and numerically for body-centered-cubic (BCC) polycrystalline microstructures based on a misorientation deviation (MD) approach. Nine monotonic tensile experiments were performed on two BCC titanium alloys inside a scanning electron microscope (SEM). The influence of reference orientation was explored both at the grain scale and at the mesoscale using electron backscattered diffraction (EBSD). The correlation between global plastic strain and the MD was quantified. The tendency for orientation change was quantified as a function of plastic strain and grain orientation for three crystallographic orientations (i.e., [100], [110], and [111]) with respect to tensile direction. The subpopulation of small grains exhibited a lower level of misorientation dispersion compared with larger grains, and this discrepancy became more pronounced at higher strains. An empirical equation was proposed to estimate the level of misorientation dispersion for individual grains as a function of grain size and global plastic strain level. Two interrupted in-situ SEM experiments were performed, and this resulted in a significantly increased misorientation compared with uninterrupted tests performed to similar plastic strain levels.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effects of oxygen on the tensile properties and fracture behavior of the Ta-10 W refractory alloy at quasi-static and impact strain rates

This study investigates effects of pre-charged oxygen at levels up to ∼1750 ppm on the tensile properties of the refractory alloy Ta-10 W. Tests were conducted at temperatures to 1100 °C and strain rates from quasi-static (∼10−3 s−1) to impact (∼103 s−1). At all temperatures, ductility decreased with increasing oxygen concentration and could be visually identified as a ductile-to-brittle transition (DBT). Additionally, for a given oxygen concentration, ductility was lower at impact strain rate than at quasi-static. The DBT was accompanied by a change from ductile transgranular to more brittle modes, intergranular and transgranular cleavage. The oxygen concentrations associated with the DBT depend on test temperature and strain rate. However, the transitions themselves are not sharp and cannot be defined as occurring at a specific oxygen concentration. At impact strain rates, ductility is relatively insensitive to test temperatures in the range 300–1100 °C with similar embrittling effects of oxygen; however, oxygen has a more severe embrittling effect at room temperature. This behavior is reversed at quasi-static strain rates where the embrittling effect of oxygen is more severe at elevated temperatures than at room temperature. It appears this difference is related to the kinetics of oxygen diffusion to grain boundaries and crack tips. Specimens that were not pre-charged with oxygen but tensile tested in various partial pressures of oxygen underwent dynamic embrittlement during the test, with the degree of embrittlement increasing as the partial pressure of oxygen in the environment increased. Consistent with such a mechanism, ductility increased with increasing strain rate for a given oxygen partial pressure, which would be the reverse if only intrinsic dislocation mobilities were controlling.

Miller, Roger [ORNL] (ORCID:0000000172155851)↗
DOE OSTI2025

A variant of the MenB strain of Synechocystis sp. PCC 6803 disrupts a stress response pathway allowing DMPBQ to occupy the A 1 sites of photosystem I

Phylloquinone (PhQ) plays a unique role in photosynthesis as the A1A and A1B intermediates in light-driven electron transfer in Photosystem I (PSI). When PhQ biosynthesis is inhibited by deletion of the menB gene in the cyanobacterium Synechocystis sp. PCC 6803, previous studies have shown that plastoquinone-9 (PQ-9) occupies the A 1 sites. However, a recent cryo-electron microscopy structure of a strain of ΔmenB from the year 2023 revealed an unusual quinone in the A 1 sites with a benzoquinone headgroup similar to PQ-9 and a phytyl tail similar to PhQ. Here, we investigate its biosynthesis and binding properties. Mass spectrometry confirms that PSI from the 2023 ΔmenB strain contains 2,3-dimethyl-5-phytyl-1,4-benzoquinone (DMPBQ), while PSI from the original strain contains PQ-9. Whole genome sequencing reveals that a mutation in slr1737 (tocopherol cyclase) leads to the accumulation of DMPBQ, an intermediate in the tocopherol biosynthetic pathway. Transient optical and electron paramagnetic resonance spectroscopy studies show that when DMPBQ occupies the A 1 sites, it does not exchange with exogenously supplied PhQ in contrast to PQ-9, which exchanges readily. We propose that the slr1737 mutation in the 2023 ΔmenB strain is a likely candidate for the source of the phenotype. This new strain has sacrificed tocopherol synthesis, the absence of which is known to have no effect on growth under low stress conditions, resulting in incorporation of DMPBQ in the A 1 sites. The tighter binding and function of DMPBQ likely allow this ΔmenB strain to outcompete its peers under optimal growth conditions and thus dominate the population.

2,3-dimethyl-5-phytyl-1,4-benzoquinone↗
DOE OSTI2022

Mechanical behavior and shear band of a powder-metallurgy-fabricated CoCrFeMnNi high-entropy alloy during high strain-rate deformation

High-entropy alloys (HEAs) fabricated by powder metallurgy are considered to exhibit extremely-great potential application values in the field for high-speed impact deformation due to their uniform microstructures and compositions. The mechanical behavior of a powder-metallurgy-fabricated (PM) CoCrFeMnNi HEA was investigated at room temperature with strain rates ranging from 1200 s -1 to 2800 s -1 . It was found that the serration behavior and shear localization of the alloy under dynamic conditions occurred. Results also indicated that the serrated flow took place in the PM CoCrFeMnNi HEA during mechanical deformation at high strain rates (>1000 s -1 ) and became more pronounced as the strain rate increased. Furthermore, it was determined that the yield-strength values of the PM CoCrFeMnNi HEA were sensitive to strain rates, where the values increased from 500 MPa to 700 MPa when the strain rates increased from 1200 s -1 to 2800 s -1 . Shear bands with a width of about 20 μm were generated in the PM CoCrFeMnNi HEA after the shear stress reached a maximum value of 635 MPa, which corresponded to a nominal strain of about 8.71. Nanotwins and ultrafine-equiaxed grains with a diameter of about 150 nm also developed at the core of the shear band during deformation. The results revealed that the strength of the shear band was much higher than that of the matrix grain. Nanotwins in the shear band were composed of a single face-centered-cubic (FCC) structure with the twin plane of ($\bar{1}$1$\bar1$), which could be formed via a rotational dynamic recrystallization (RDR).

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of epitaxial strain on the optical properties of NaOsO 3

We study the electronic and optical properties of NaOsO 3 under epitaxial strain using first principles methods. Structural optimization shows important changes with strain in the structural parameters such as the Os O bond lengths and the octahedral rotation angles. The key change in the electronic structure is the band gap, which increases with compressive epitaxial strain and decreases with tensile strain. The computed optical absorption coefficient is more or less isotropic for the unstrained structure for light polarization along the three crystallographic directions, but for the strained structure, it is enhanced if the light polarization is along a compressed crystallographic direction due to strain. This is explained in terms of the admixture of Os ( p ) orbitals with the Os ( d ) states that form the valence and the conduction bands.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

A new observation of strain-induced grain boundary serration and its underlying mechanism in a Ni–20Cr binary model alloy

Highlights: • Grain boundary serration was first found to occur in Ni–Cr binary alloy with no precipitate. • The mechanism of segregation-induced serration was proposed. • The serrated grain boundary was enriched with Cr atoms as high as 87 at.%. • The critical strain energy for the serration was determined to be lower than 0.97 kJ/mol. - Abstract: The formation of serrated grain boundaries and its mechanism correlated with straining exerted on grain boundaries were investigated in a Ni–20Cr binary model alloy. This model alloy is a full solid-solution which is deliberately free of carbon and aluminum to exclude precipitation of second phase. A special heat treatment involving slow cooling was used to promote grain boundary serration, which is known to enhance creep properties by decreasing interfacial free energy. No sign of serration could be observed for the Ni–20Cr model alloy, as expected. However, we found that a compressive 5% strain hold applied during slow cooling successfully induced grain boundary serration. The compressive 5% strain hold generated dislocations near the grain boundary, which promoted Cr enrichment near and at the grain boundary. To dismiss the effect of dislocations, straining was removed and the solutionizing temperature was increased in order to promote Cr enrichment near and at grain boundaries by means of vacancy-assisted diffusion of Cr atoms from the bulk to grain boundaries during slow cooling. Significant grain boundary serration was again observed. Atom probe tomography analyses showed that the serrated grain boundary with a wide width of ~ 10 nm was enriched with Cr atoms, as much as 87 at.%, while the γ matrix only contained 34 at.%. First-principles calculations showed that the strain energy necessary for the onset of grain boundary serration is lower than 0.97 kJ/mol.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mapping strain and structural heterogeneities around bubbles in amorphous ionically conductive Bi 2 O 3

While amorphous materials are often approximated to have a statistically homogeneous atomic structure, they frequently exhibit localized structural heterogeneity that challenges simplified models. This study uses 4D scanning transmission electron microscopy to investigate the strain and structural modifications around gas bubbles in amorphous Bi 2 O 3 induced by argon irradiation. We present a method for determining strain fields surrounding bubbles that can be used to measure the internal pressure of the gas. Compressive strain is observed around the cavities, with higher-order crystalline symmetries emerging near the cavity interfaces, suggesting paracrystalline ordering as a result of bubble coarsening. This ordering, along with a compressive strain gradient, indicates that gas bubbles induce significant localized changes in atomic packing. By analyzing strain fields with maximum compressive strains of 3%, we estimate a lower bound on the internal pressure of the bubbles at 2.5 GPa. These findings provide insight into the complex structural behavior of amorphous materials under stress, particularly in systems with gas inclusions, and offer new methods for probing the local atomic structure in disordered materials. Although considering structural heterogeneity in amorphous systems is non-trivial, these features have crucial impacts on material functionalities, such as mechanical strength, ionic conductivity, and electronic mobility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of defect characteristics on tensile deformation of an additively manufactured stainless steel: Evolutions of texture and intergranular strain

The micromechanics of plastic deformation behavior of a selective laser melt processed austenitic stainless steel were studied by investigating the evolutions of texture and intergranular strain using in situ high-energy synchrotron x-ray diffraction (sXRD). The effects of defect characteristics on tensile behavior were studied using three different samples: a near full-density sample with elliptical closed voids and two samples with lack-of-fusion (LOF) defects tensile loaded either perpendicular or parallel to their major axes. The evolutions of pole figures and inverse pole figures show that the full-density specimen develops a strong (111)/(200) fiber texture along the loading direction. For both LOF specimens, the evolution of texture is qualitatively similar to the full-density counterpart, but the development of the fiber texture was much slower, indicating a limited plasticity at a given macroscopic strain. The intergranular strain evolution in the full-density specimen is similar to that of a wrought 316L stainless steel. Conversely, a significantly different intergranular strain development was observed in a LOF specimen, where tensile strain development was observed in both the axial and transverse directions. Finally, the influence of defect type, density, and orientation on the local stress states in the steel matrix and the evolutions of intergranular strains is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Strain Relaxation and Relative Defect Density with Thickness in MBE-Grown Ge 0.85 Sn 0.15 on Ge(001)

Germanium–tin (GeSn) alloys are emerging as promising materials for mid-infrared optoelectronics and silicon-compatible photonic devices, owing to their tunable direct bandgap. However, the growth of high-quality GeSn films with high Sn content remains challenging due to strain-induced defect formation. In this study, we investigate the role of film thickness on strain-induced relaxation, defect density, and Sn segregation. A series of five samples with varying thicknesses and ∼15% Sn-containing GeSn layers were grown, ranging from the critical thickness for strain relaxation to the onset of Sn segregation. All GeSn samples were analyzed using X-ray diffraction reciprocal space mapping (XRD-RSM) to explore the evolution of strain-induced relaxation as a function of thickness. Photoluminescence measurements reveal that increasing the GeSn thickness enhances strain relaxation while reducing defect-related emission, indicating a decrease in effective defect density prior to reaching the threshold thickness of GeSn layer. At a thickness of ∼150 nm, the GeSn layer shows the onset of Sn segregation, evident in the XRD-RSM spectrum, marking the threshold thickness for Sn segregation. This work defines an effective growth window in terms of thickness (35 to 150 nm) for fabricating relaxed, defect-suppressed GeSn layers with 15% Sn content. These findings emphasize the crucial role of thickness control in balancing strain relaxation and defect suppression, advancing the fabrication of high-quality, high Sn-content relaxed GeSn using molecular beam epitaxy.

Defects↗