SEARCH · Engineering Papers

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Statistical characterization of the fatigue behavior of composite lamina

A theoretical model was developed to predict statistically the effects of constant and variable amplitude fatigue loadings on the residual strength and fatigue life of composite lamina. The parameters in the model were established from the results of a series of static tensile tests and a fatigue scan and a number of verification tests were performed. Abstracts for two other papers on the effect of load sequence on the statistical fatigue of composites are also presented.

Yang, J. N.↗

NASA NTRS1979

Effects of wing leading-edge deflection on low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration

Static force tests were conducted in the Langley V/STOL tunnel at a Reynolds number (based on the mean aerodynamic chord) of about 2.0 x 10 to the 6th power for an angle-of-attack range from about - 10 deg to 17 deg and angles of sideslip of 0 and + or - 5 deg. Limited flow visualization studies were also conducted in order to provide a qualitative assessment of leading-edge upwash characteristics.

Coe, P. L., Jr.↗

NASA NTRS1979

Reliability measurement for operational avionics software

Quantitative measures of reliability for operational software in embedded avionics computer systems are presented. Analysis is carried out on data collected during flight testing and from both static and dynamic simulation testing. Failure rate is found to be a useful statistic for estimating software quality and recognizing reliability trends during the operational phase of software development.

Thacker, J.↗

NASA NTRS1980

Exploratory investigation of the effects of vortex bursting on the high angle-of-attack lateral-directional stability characteristics of highly-swept wings

A recent low-speed wind-tunnel investigation of highly-swept wings has shown that vortex breakdown at high angles of attack can cause large destabilizing effects on static lateral-directional stability characteristics, and that the destabilizing effects of vortex breakdown can be greatly aggravated by model support strut interference effects. The present paper discusses these effects based on the results of static force tests of several highly-swept wing configurations for different wind-tunnel strut setup arrangements. Also included in the paper are photographs obtained during tuft-, smoke-, and helium-bubble flow visualization studies to indicate wing flow behavior patterns

Johnson, J. L., Jr.↗

NASA NTRS1980

Fan noise caused by the ingestion of anisotropic turbulence - A model based on axisymmetric turbulence theory

An analytical model of fan noise caused by inflow turbulence, a generalization of earlier work by Mani, is presented. Axisymmetric turbulence theory is used to develop a statistical representation of the inflow turbulence valid for a wide range of turbulence properties. Both the dipole source due to rotor blade unsteady forces and the quadrupole source resulting from the interaction of the turbulence with the rotor potential field are considered. The effects of variations in turbulence properties and fan operating conditions are evaluated. For turbulence axial integral length scales much larger than the blade spacing, the spectrum is shown to consist of sharp peaks at the blade passing frequency and its harmonics, with negligible broadband content. The analysis can then be simplified considerably and the total sound power contained within each spectrum peak becomes independent of axial length scale, while the width of the peak is inversely proportional to this parameter. Large axial length scales are characteristic of static fan test facilities, where the transverse contraction of the inlet flow produces highly anisotropic turbulence. In this situation, the rotor/turbulence interaction noise is mainly caused by the transverse component of turbulent velocity.

Kerschen, E. J.↗

NASA NTRS1980

Contact law and impact responses of laminated composites

Static identation tests were performed to determine the law of contact between a steel ball and glass/epoxy and graphite/epoxy laminated composites. For both composites the power law with an index of 1.5 was found to be adequate for the loading curve. Substantial permanent deformations were noted after the unloading. A high order beam finite element was used to compute the dynamic contact force and response of the laminated composite subjected to the impact of an elastic sphere. This program can be used with either the classical Hertzian contact law or the measured contact law. A simple method is introduced for estimating the contact force and contact duration in elastic impacts.

Sun, C. T.↗

NASA NTRS1980

Mechanical suppression: Modern technology applied to an old art

Various suppressor configurations were analyzed and evaluated in an effort to reduce combustion instability and improved ballistic reproducibility of the MK 12 motor. A static firing test series of eight field return boosters featured two baseline motor firings with the existing suppressor in each motor, followed by two tests each of two different prototype suppressor designs. Results were analyzed and used to generate the design for the final two firings. Acoustic pressure pulsers were utilized to measure the damping effectiveness of the final design. The reduction in motor vibration and acoustic pressure levels between the baseline tests and the final two improved lightweight tests was significant. The average acceleration level of the motors equipped with flightweight rods was reduced to only 5% of the level in the unmodified motors; the average acoustic pressure level was reduced to 20%; maximum values were reduced to 6% for acceleration and 23% for pressure.

Crockford, W. H.↗

NASA NTRS1981

Self-induced wing rock of slender delta wings

As part of a research program aimed at exploring basic mechanisms that cause wing rock in combat aircraft, an investigation was conducted to study the aerodynamic factors which cause the low-speed wing rock exhibited by slender delta wings. A flat-plate delta wing with 80 deg leading-edge sweep was subjected to conventional static-force tests and dynamic wind-tunnel experiments which included forced-oscillation, rotary, and free-to-roll tests. In addition, visualization of the flow phenomena involved was obtained by observing tuft patterns and using a helium-bubble technique. This paper summarizes the results of this study. Fundamental information is presented on the aerodynamic mechanisms that cause the wing rock and the problem of mathematically modeling the aerodynamics and motions is discussed.

Nguyen, L. T.↗

NASA NTRS1981

Indentation law for composite laminates

Static indentation tests are described for glass/epoxy and graphite/epoxy composite laminates with steel balls as the indentor. Beam specimens clamped at various spans were used for the tests. Loading, unloading, and reloading data were obtained and fitted into power laws. Results show that: (1) contact behavior is not appreciably affected by the span; (2) loading and reloading curves seem to follow the 1.5 power law; and (3) unloading curves are described quite well by a 2.5 power law. In addition, values were determined for the critical indentation, alpha sub cr which can be used to predict permanent indentations in unloading. Since alpha sub cr only depends on composite material properties, only the loading and an unloading curve are needed to establish the complete loading-unloading-reloading behavior.

Yang, S. H.↗

NASA NTRS1982

Oxidation stability of advanced reaction-bonded Si3N4 materials

Four slip-cast, injection-molded and isostatically-pressed specimens of reaction-bonded silicon nitride (RBSN) were subjected to static oxidation tests at 900 C for 10 hours. Specimens containing 8-10% interconnected open porosity of size greater than one micron exhibited a 20-30% decrease in average room temperature four-point flexure strength, while those with 10% open porosity of magnitudes much smaller than one micron as well as those with 2-4% interconnected open porosity of about one micron did not decrease in strength after 900 C exposure. It was determined that preoxidation treatment at 1350 C prevents the 20-30% strength degradation due to internal oxidation, and evidence is presented which suggests that surface pit formation in some RBSN may result from contamination by the furnace environment rather than any intrinsic material properties.

Lindberg, L. J.↗

NASA NTRS1983

Exploratory low-speed wind-tunnel investigation of advanced commuter configurations including an over-the-wing propeller design

A recent low-speed wind-tunnel investigation of a three-surface regional transport configuration has shown large favorable power effects on longitudinal and lateral stability and marginal engine-out trim characteristics for some aft engine and empennage configurations. The present paper discusses these results in terms of static force test information obtained for power-off and power-on conditions. Also discussed in this paper are wind-tunnel results which indicate that mounting propellers over the wing can introduce large favorable slipstream interference effects which significantly reduce the wing drag at climb power conditions.

Johnson, J. L., Jr.↗

NASA NTRS1983

Determination of the static performance of a Cuyuna cc model UL-430RR engine

The results of static performance tests were carried out on an ultralight engine. A Cuyuna 430 cc, 2 stroke, 2 cylinder model was used to measure thrust, torque, propeller RPM, fuel flow, cylinder head temperature, and change in pressure through the propeller. Measurement of each of the above parameters was taken at specific values of RPM. The propeller's RPM's ranged from idle at approximately 750 RPM to a maximum value of 2810 RPM. The test results were then manipulated to obtain thrust coefficient, power coefficient, shaft horse power, and shaft specific fuel consumption.

Roskam, J.↗

NASA NTRS1982

Indentation law for composite laminates

Yang, S. H.↗

NASA NTRS1984

Initial Sailplane Project: The RP-1

The annual static loading tests were made on the assembled wing/fuselage structure of the RP-1 sailplane. Simple wing bending and wing bending/torsion tests up to about four G's were made, using sand bag loading on the inverted aircraft. Bending a torsion deflections were measured and compared to those obtained in previous years' tests. It appears that the structure is retaining its original strength and stiffness very well. This aircraft has been disassembled and stored on the Jonsson Engineering Center under ambient, indoor conditions of temperature and humidity.

Source record↗

NASA NTRS1984

Effects of high energy radiation on the mechanical properties of epoxy-graphite fiber reinforced composites

The effects of high energy radiation on the mechanical properties and on the molecular and structural properties of graphite fiber reinforced composites were assessed so that the durability of such composites in space applications could be predicted. Investigative techniques including ESR and infrared spectroscopy, ESCA, contact angle measurements, and dynamic and static mechanical testing (3-point bending and interlaminar shear) were employed. The results using these different techniques are individually described, and the implications of the data are discussed. The proposed plan of work for the next fiscal year is outlined.

Fornes, R. E.↗

NASA NTRS1986

Development of pneumatic thrust-deflecting powered-lift systems

Improvements introduced into the Circulation Control Wing/Upper Surface Blowing (CCW/USB) STOL concept (Harris et al., 1982) are described along with results of the full-scale static ground tests and model-scale wind tunnel investigations. Tests performed on the full-scale pneumatic thrust-deflecting system installed on the NASA QSRA aircraft have demonstrated that, relative to the original baseline configuration, a doubling of incremental thrust deflection due to blowing resulted from improvements that increased the blowing span and momentum, as well as from variations in blowing slot height and geometry of the trailing edge. A CCW/Over the Wing model has been built and tested, which was shown to be equivalent to the CCW/USB system in terms of pneumatic thrust deflection and lift generation, while resolving the problem of cruise thrust loss due to exhaust scrubbing on the wing upper surface.

Englar, R. J.↗

NASA NTRS1985

Dynamics of liquid sloshing in upright and inverted bladdered tanks

A system identification methodology was used to examine the dynamics of liquid sloshing in the upright and inverted bladdered hydrazine tanks of the Tracking and Data Relay Satellite, (TDRS) and to evaluate the effects of bladder stiffness on the sloshing parameters. Mechanical models of the two systems were developed using the numerical values derived from static stability tests and from slosh frequency response tests of a full-size model tank fitted with a prototype bladder. For the upright tank (liquid below the bladder) a modified conventional pendulum was used. In the inverted tank (liquid above the bladder) where sloshing is unconventional due to the highly nonsymmetrical orientation of the liquid held by the bladder, a mechanical model using an inverted pendulum which is able to undergo small oscillations as well as large reorientations was necessary. Both thrusting and low-gravity conditions are considered.

Dodge, F. T.↗

NASA NTRS1985

Effect of fiber and matrix maximum strain on the energy absorption of composite materials

Static crushing tests were conducted on graphite composite tubes to examine the influence of fiber and matrix maximum strain at failure on the energy absorption capability of graphite reinforced composite material. Fiber and matrix maximum strain at failure were determined to significantly effect energy absorption. The higher strain at failure composite material system, AS-4/5245, exhibited superior energy absorption capability compared to AS-4/934, T300/5245 or T300/934 composite material. Results of this investigation suggest that to achieve maximum energy absorption from a composite material a matrix material that has a higher strain at failure than the fiber reinforcement should be used.

Farley, G. L.↗