Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Interfacial characteristics of P91 steel - Inconel 740H bimetallic structure fabricated using wire-arc additive manufacturing

Although bimetallic structures can offer unique solutions to engineering problems with varying functionality, joining two dissimilar alloys using additive manufacturing involves challenges such as cracking and segregation. In this work, bimetallic structures of Inconel 740H superalloy and P91 steel are processed using wire-arc additive manufacturing (WAAM) for the first time. P91 steel is directly deposited over 740H with a cooling time of 20 minutes in between the two depositions. During microstructure characterization, a large gradient zone with coarse grains spanning for ~2200 μm is observed. Moreover, the microhardness of the gradient zone is the least in comparison with the P91 and 740H deposits. No deleterious phase formation is found; however, intergranular cracks are observed along the gradient zone. In order to deduce the reason for cracking, non-equilibrium solidification simulations are performed for the mixed compositions of P91 and 740H in the gradient zone. Here, the reasons for crack formation in the gradient zone are the sudden change in the volumetric coefficient of thermal expansion due to the formation of MC carbides as well as the development of local strains from the thermal residual stresses. Therefore, altering the deposition sequence and introducing gradient layers with mixed composition between the P91 and 740H deposits will be beneficial in achieving defect-free builds. Through the integration of experiments and simulation, this work gains valuable insights into the processability of dissimilar alloy manufacturing using the WAAM technique.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Synthesis, structural, and magnetic properties of Heusler-type Mn 2-x Fe 1+x Ge (0.0 ≤ x ≤ 1.0) alloys

Bulk Mn 2-x Fe 1+x Ge (0.0 ≤ x ≤ 1.0) alloys have been synthesized by arc-melting followed by a low temperature homogenization thermal annealing, whereas for comparison purposes the Mn 2 FeGe alloy was also produced in ribbon form by rapid solidification. Here, a study of the structural and magnetic properties is presented. Contrary to theoretical predictions, Mn 2 FeGe crystallizes in a hexagonal DO 19 crystal structure (space group P63/mmc) and orders ferromagnetically with a saturation magnetization (M S ) value of ~1.7 µB/f.u. in the ground state. With the substitution of Fe for Mn in bulk Mn 2-x Fe 1+x Ge, we observed an increase in the FM interactions with a maximum MS value of 5.1 µ B /f.u. for x = 1.0, and a significant progressive increase in the Curie temperature (T C ) in a wide range spanning ~200 K to over 400 K.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A snapshot of high-entropy alloy processing techniques and their effects on resulting mechanical properties

High-entropy alloys (HEAs) exhibit exceptional strength, corrosion resistance, and thermal stability, making them promising candidates for nuclear, aerospace, and other extreme applications. While most prior work has focused on compositional design, manufacturing techniques themselves can alter microstructure and mechanical properties as dramatically as alloy chemistry. This review compiles and compares the effects of processing routes—including arc melting, induction melting, mechanical alloying with spark plasma sintering, and additive manufacturing—on the structure and properties of HEAs. Quantitative comparisons highlight, for example, that SPS-processed alloys can achieve ∼20–45 % higher yield and tensile strength than arc-melted counterparts, while Bridgman solidification produces nearly single-crystal structures with elongation to failure exceeding 80 %. Additive manufacturing routes such as selective laser melting offer fine microstructures but also introduce anisotropy and porosity, leading to yield strengths spanning 100–600 MPa for the same composition. By synthesizing such results, this review provides actionable insight into how processing routes interact with HEA core effects (high entropy, lattice distortion, sluggish diffusion, and cocktail effect) to determine performance, thereby offering a practical guide for optimizing manufacturing strategies.

36 MATERIALS SCIENCE↗
DOE OSTI2026

The effect of varying powder feedstock chemistry and printing atmosphere on the microstructure of additively manufactured nickel-based ODS alloys: Role on stabilization of cellular structures vs. oxide dispersion formation

Nickel-based alloys have a wide variety of structural applications due to their high corrosion resistance and mechanical strength which depend on solid solution strengthening, or the formation of oxides and/or intermetallic precipitation for their properties. In this study, the microstructure of six Ni–Cr–Y–Ti–Al powder batches designed for the production of oxide dispersion strengthened nickel were compared. These batches varied in chemistry and atomization technique used which included Gas Atomization Reactive Synthesis (GARS). The batches of powder were then consolidated via Additive Manufacturing (AM) Powder Bed Fusion using Laser Beam (PBF-LB) and characterized via transmission electron microscopy to elucidate the influence of powder feedstock (i.e. synthesis methodology and chemistry) on the PBF-LB microstructure. The study investigates (i) how the amount of yttrium and titanium additions in the powder feedstock and the addition of oxygen during the processing (through GARS) affect the microstructure of the powder itself and the AM printed microstructure, and (ii) how the control of oxygen addition in the printing atmosphere during the PBF-LB printing process itself is another important parameter for achieving the formation of the wanted oxide dispersion versus the stabilization of the cellular structure (often observed in AM processed alloys). Microstructural characterization of both powder particles and additively manufactured nickel alloys in this study provide important insights into the movement of yttrium within the material upon solidification, particularly along cell boundaries, and how yttrium behaves depending on alloy chemistry. When a threshold of yttrium content is reached within the system, yttrium consistently reacts to form an intermetallic along cell boundaries instead of forming oxide nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Design and development of a high-performance Ni-based superalloy WSU 150 for additive manufacturing

This work proposes a design and development strategy of a new nickel-based superalloy for additive manufacturing. A new Ni-based superalloy has been developed by the application of the combinatorial alloy development technique coupled with CALPHAD based solidification modeling by effectively suppressing the precipitation kinetics. The suppression of precipitation during processing paved a way for prevention of cracks during deposition. The new alloy "WSU 150" revealed excellent room temperature mechanical properties with a yield strength of 867 MPa, an ultimate tensile strength of 1188 MPa, and an elongation of 27.9% in the as-deposited condition. The mechanical properties of the heat-treated alloy were improved significantly to 1114 MPa yield strength, 1396 MPa ultimate tensile strength, and an elongation of 16.1%. Improvement in the mechanical properties is attributed to the additional precipitation and coarsening of γ' and carbides during heat-treatment. Microstructural investigation of the alloy revealed spherical γ' with a rippled size distribution from the center to the interdendritic region. The average size of the γ' particles in the as-deposited condition was found to be around 48 nm in the interdendritic region. Heat-treatment promoted the coarsening of γ' which is explained in the paper.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Characterization and calibration of a viscoelastic simplified potential energy clock model for inorganic glasses

In this study, to analyze the stresses and strains generated during the solidification of glass-forming materials, stress and volume relaxation must be predicted accurately. Although the modeling attributes required to depict physical aging in organic glassy thermosets strongly resemble the structural relaxation in inorganic glasses, the historical modeling approaches have been distinctly different. To determine whether a common constitutive framework can be applied to both classes of materials, the nonlinear viscoelastic simplified potential energy clock (SPEC) model, developed originally for glassy thermosets, was calibrated for the Schott 8061 inorganic glass and used to analyze a number of tests. A practical methodology for material characterization and model calibration is discussed, and the structural relaxation mechanism is interpreted in the context of SPEC model constitutive equations. SPEC predictions compared to inorganic glass data collected from thermal strain measurements and creep tests demonstrate the ability to achieve engineering accuracy and make the SPEC model feasible for engineering applications involving a much broader class of glassy materials.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Separate effects identification via casting process modeling for experimental measurement of U–Pu–Zr alloys

Computational simulations of gravity casting processes for metallic U–Pu–Zr nuclear fuel rods have been performed using a design-of-experiments technique to determine the fluid flow, liquid heat transfer, and solid heat transfer parameters which most strongly influence the process solidification speed and fuel rod porosity. The results are used to make recommendations for the best investment of experimental time and effort to measure process parameters.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Plasma and X-ray radiation-induced damage mechanisms in a tungsten heavy alloy

Tungsten-based materials are among the main candidate plasma-facing materials for future fusion reactors where extreme conditions of thermomechanical stresses, radiation, and energetic particles must be withstood. Here a hybrid X-pinch platform combined with a pulsed power machine was used to study damage mechanisms in 90W–4Cu–6Ni tungsten heavy alloy as a result of exposure to high energy density plasma, X-ray radiation, and the resulting thermal shock. It was found that the plasma-facing surface of the material undergoes severe melting and ablation with the extent of ablation being higher in the Cu–Ni phase than the W particles. Rapid melting and solidification transform the W particles into fine dendrite morphologies embedded in the Cu–Ni solid solution. Cracking was also observed in the subsurface layers at the interfaces between the W particles and the Cu-rich phase of the Cu–Ni matrix. X-ray radiation, on the other hand, cause slight melting on the surface without significant ablation and no cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Irradiation-assisted cracking of SA508-304L weldments with 308L groove filler and 309L butter in hot water immersion constant rate extension tests

Low alloy SA508 bainitic steel is often welded to 300 series austenitic stainless steel in nuclear power plants. These dissimilar metal weldments use 309L butter applied to the low alloy steel and 308L groove filler material to join the 309L to austenite. High alloy steels (such as the 308L and 309L material used here) have been identified as having greater susceptibility to irradiation-assisted stress corrosion cracking (IASCC). Evidence is presented here of cracking under tensile loads in 309L weldment butter in LWR hydrothermal conditions that correlates irradiation induced changes at δ ferrite–γ austenite phase boundaries and γ–γ grain boundaries; specifically intergranular Cr 23 C 6 precipitates. Cracking is not observed in irradiated 308L groove filler under the same conditions. Both the 309L butter and 308L filler material have a duplex or mixed δ–γ phase microstructure due to solidification during the welding procedure. We have performed constant extension rate autoclave immersion tests in BWR normal water chemistry hot water (288 °C, 10 MPa, 2000 wt. ppb dissolved oxygen, <100 nS/cm conductivity, neutral pH) of proton irradiated (2 MeV, approximately 3 displacements per atom at a depth of 10 μm) tensile specimens. Proton irradiation to the dpa levels used here induced Cr 23 C 6 carbide precipitation at γ–γ grain boundaries and δ–γ phase boundaries in the 309L butter but not the 308L filler. Cracking was observed in the proton-irradiated volume of 309L at these interfaces in the vicinity of the Cr 23 C 6 precipitates. We hypothesis the SA508 is the source of carbon in the 309L butter. Cr depletion at γ–γ grain boundaries was also observed and may also be a root cause of cracking. Furthermore, the 309L butter is under significant tensile residual stress in the weldment that adds to applied tensile loads and this too may be a contributing factor.

309L weld butter↗
DOE OSTI2025

Strength and ductility of additively manufactured 316L stainless steel: Impact of neutron irradiation and data variability

Here, this article presents the mechanical properties of additively manufactured (AM) 316L stainless steel processed via the laser powder bed fusion (LPBF) method, focusing on the effects of neutron irradiation on mechanical properties and the variability in strength and ductility data. The rapid melting-solidification process and multiple heating-cooling cycles inherent in LPBF typically result in a fine, metastable microstructure with significant local variability. AM 316L builds of varying thicknesses were fabricated, and SS-J3 miniature tensile specimens were machined from six different locations. These specimens were irradiated with fast neutrons to doses of 2 and 10 dpa at target temperatures of 300 °C and 600 °C. Post-irradiation tensile tests were conducted at room temperature, 300 °C, and 600 °C. Compared to conventional 316L stainless steel, AM 316L exhibited higher initial strength but lower ductility. Irradiation at 300 °C caused significant hardening and prompt necking at yield, with limited uniform ductility, although embrittlement was not observed up to 10 dpa. While neutron irradiation, particularly at 600 °C, increased the variability in strength and ductility data, no clear dependence of mechanical properties on build thickness or sampling location was found—contrary to the conventional perception that AM materials may exhibit high property variability. Furthermore, we observed that the variability in property data for LPBF-processed 316L was relatively low compared to that of wrought 316L stainless steel. This reduced variability in AM 316L steel may be attributed to its highly metastable, stress-containing microstructure, which is discussed in the context of general tensile property variations.

Additively manufactured 316L stainless steel↗
DOE OSTI2025

Laser repair welding of irradiated alloy 182

Welding repair of irradiated nickel-based alloys, such as Alloy 182, poses a significant challenge due to helium-induced cracking (HeIC) and grain boundary degradation (GBD) in the heat affected zone, driven by helium accumulation at grain boundaries and welding-induced tensile stresses. This study investigates the weldability of irradiated Alloy 182 up to 15 wppm doped boron using both conventional laser welding and the Auxiliary Beam Stress Improved (ABSI) laser welding technique. While HeIC was observed at the weld toe of the entry pass in both methods due to the higher effective heat input associated with the initial pass directly on the base metal, no additional cracking occurred elsewhere, even at elevated helium concentrations. Optical and scanning electron microscopy analysis revealed that the ABSI technique, which introduces additional compressive stresses to counteract solidification-induced tensile stresses, significantly reduced GBD formation, lowering its total count from 1,230 to 339 and decreasing both average and maximum GBD lengths. In conclusion, these results demonstrate that the ABSI technique is a promising approach to mitigate helium-induced damage and improve the weldability of irradiated Alloy 182, offering a viable solution for structural repairs for long-term operation of existing nuclear reactors.

grain boundary degradation↗
DOE OSTI2017

Cesium incorporation in hollandite-rich multiphasic ceramic waste forms

Hollandite-rich multiphase waste form compositions processed by melt-solidification and spark plasma sintering (SPS) were characterized, compared, and validated for nuclear waste incorporation. Phase identification by x-ray diffraction (XRD) and electron back-scattered diffraction (EBSD) confirmed hollandite as the major phase present in these samples along with perovskite, pyrochlore and zirconolite. Distribution of selected elements observed by wavelength dispersive spectroscopy (WDS) maps indicated that Cs formed a secondary phase during SPS processing, which was considered undesirable. On the other hand, Cs partitioned into the hollandite phase in melt-processed samples. Further analysis of hollandite structure in melt-processed composition by selected area electron diffraction (SAED) revealed ordered arrangement of tunnel ions (Ba/Cs) and vacancies, suggesting efficient Cs incorporation into the lattice.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Pore habit of methane hydrate and its evolution in sediment matrix – Laboratory visualization with phase-contrast micro-CT

Describing the pore habit of methane hydrate in sediment matrices is essential for understanding natural distribution of methane hydrate, methane trace (transport and solidification) in the hydrate stability zone, physical properties of hydrate-bearing sediments, and the associated influence on potential gas production. Pore habit visualization in natural media at pore scale even with laboratory synthesized cores has been challenging due to the similar densities of methane hydrate from pore liquid. In this work, we used phase-contrast assisted micro-CT with potassium iodine-doped brine to visualize four phases: sand particles, pore fluid, methane hydrate and methane gas. This study visualizes the pore habit of methane hydrate at various stages including during hydrate formation in excess-gas systems, its evolution after brine injection to replace pore fluid, and hydrate formation in excess-water systems. Hydrate tends to adopt round and smooth surfaces when in contact with water while exhibits relatively angular interfaces when in contact with methane gas. Hydrate formation in excess-gas systems results in a partial cementing and partial mineral-coating pore habit, while hydrate in excess-water systems develops mainly as pore-filling, and locally cementing or mineral-coating where big gas pockets exist at the initial state. Pore liquid replacement from methane gas to brine triggers a shift of hydrate pore habit towards pore-filling. Methane hydrate evolution over time produces bigger hydrate particles but with less contact area with sand particles. The effects of hydrate pore habit become less important as hydrate particle size exceeds the pore size. Additionally, hydrate formation could trap residual methane gas and brine as inclusions.

58 GEOSCIENCES↗
DOE OSTI2013

Microstructural and mechanical characterization of Al–Zn–Si nanocomposites

In this paper the addition of silicon nanoparticles into Al–Zn alloys to form metallic matrix nanocomposites by mechanical alloying process was investigated. The influence of various process parameters such as milling time and Si concentration in the Al–Zn matrix has an interesting effect on the microstructure and mechanical properties of the synthesized nanocomposites. The microstructural characterization of the nanocomposites was evaluated by transmission electron microscopy and energy dispersive X-ray spectroscopy (TEM–EDXS) and the mechanical properties were measured by nanoindentation and micro-hardness tests. The results showed that during mechanical milling Si is added to the Al–Zn matrix achieving a uniform and homogeneous dispersion. After solidification, it forms small particles of AlZnSi with blocky morphology in interdendritic regions. The nanoindentation profiles showed that the elastic modulus and hardness properties increase with increasing milling time. However, a high concentration of Si (> 1.2 wt.%) results in a saturation of Si in the Al–Zn matrix, which adversely affects the mechanical properties. Thus, it is important to tune the milling time and concentration of Si added to the Al–Zn alloys to control the growth of brittle phases that result in reduction of the mechanical properties of the material. - Highlights: • A novel technique for addition of Si nanocomposites into Al–Zn liquid alloy is reported. • Good dispersion and homogeneity of Si in the Al–Zn matrix are obtained. • Increasing Si content above 1.2 wt.% decreases the mechanical properties of Al–Zn alloy. • The saturation point of Si in 1.2 wt.% differs from Galvalume® composition. • The Al–Zn–1.5Si alloy with addition of nanocomposite shows 5.7 GPa of hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti-6Al-4V by selective electron beam melting

With titanium alloys, the solidification conditions in Additive Manufacturing (AM) frequently lead to coarse columnar β-grain structures. The effect of geometry on the variability in the grain structure and texture, seen in Ti-6Al-4V alloy components produced by Selective Electron Beam Melting (SEBM), has been investigated. Reconstruction of the primary β-phase, from α-phase EBSD data, has confirmed that in bulk sections where in-fill “hatching” is employed growth selection favours columnar grains aligned with an <001> {sub β} direction normal to the deposited powder layers; this results in a coarse β-grain structure with a strong < 001 > {sub β} fibre texture (up 8 x random) that can oscillate between a near random distribution around the fibre axis and cube reinforcement with build height. It is proposed that this behaviour is related to the highly elongated melt pool and the raster directions alternating between two orthogonal directions every layer, which on average favours grains with cube alignment. In contrast, the outline, or “contour”, pass produces a distinctly different grain structure and texture resulting in a skin layer on wall surfaces, where nucleation occurs off the surrounding powder and growth follows the curved surface of the melt pool. This structure becomes increasingly important in thin sections. Local heterogeneities have also been found within different section transitions, resulting from the growth of skin grain structures into thicker sections. Texture simulations have shown that the far weaker α-texture (∼ 3 x random), seen in the final product, arises from transformation on cooling occurring with a near random distribution of α-plates across the 12 variants possible from the Burgers relationship. - Highlights: • Distinctly different skin and bulk structures are produced by the contour and hatching passes. • Bulk sections contain coarse β-grains with a < 001 > fibre texture in the build direction. • This oscillates between a random distribution around the axis and cube reinforcement. • In the skin layer nucleation occurs off the surrounding powder bed and growth occurs inwards. • Simulations show that a weak α-texture results from a random distribution across habit variants.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Chemical banding revealed by chemical etching in a cold-rolled metastable stainless steel

The current work describes the metallographic characterization of the initial microstructure of a cold rolled precipitation hardening semi-austenitic stainless steel (12Cr–9Ni–4Mo–2Cu–1Ti, in wt.%). The use of the Lichtenegger and Blöch (L–B) color etching solution has been shown to reveal not only the phases present in the microstructure, but also the existence of chemical banding along the rolling direction. The L–B reagent has been found to color the microstructure in bands depending on what alloying elements have segregated to each band. Two-dimensional electron probe microanalysis (EPMA) maps have shown that Ni, Cu and Ti segregate together in the bands, while Cr has an opposite behavior. Mo has a mixed segregation behavior although much weaker than the other elements and more prompt to segregate like Ni does. A direct comparison of light optical micrographs with the EPMA maps of the same area of the microstructure has enable to establish a direct relationship between the alloying element band concentration and the resulting etching color contrast obtained with the L–B reagent. Thermodynamic calculations predict that solidification in this steel takes place with ferrite as the primary phase. Equilibrium partitioning coefficient calculations seem to support the observed segregation patterns. - Highlights: • A cold rolled metastable stainless steel has been characterized thoroughly. • EPMA shows that Ni, Cu and Ti segregate together; Cr in an opposite way. • L–B color etching is sensitive to the segregation of these chemical elements. • This chemical banding has been reduced by applying a homogenization heat treatment. • Partitioning coefficient calculations agree with the observed segregation patterns.

36 MATERIALS SCIENCE↗