Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Solid state sequencer system

Development and characteristics of solid state sequencer system to perform abort and separation functions on space shuttle

Leck, D. E.↗

Three types of solid state remote power controllers

Three types of solid state Remote Power Controller (RPC) circuits for 120 Vdc spacecraft distribution systems have been developed and evaluated. Both current limiting and noncurrent limiting modes of overload protection were developed and were demonstrated to be feasible. A second generation of circuits was developed which offers comparable performance with substantially less cost and complexity. Electrical efficiency for both generations is 98.5 to 99%. This paper describes various aspects of the circuit design, trade-off studies, and experimental test results. Comparisons of design parameters, component requirements, and engineering model evaluations will emphasize the high efficiency and reliability of the designs.

Baker, D. E.↗

Observation of the core of the Perseus cluster with the Einstein solid state spectrometer: Cooling gas and elemental abundances

Solid State Spectrometer observations of the core of the Perseus cluster have resulted in the detection of X-ray emission lines due to Si, S, and Fe. Analysis of the spectrum indicates that the X-ray emission has at least two characteristic temperatures. This is interpreted in the framework of radiative accretion in the core of the cluster. The derived parameters are a cooling time tc less than 2 x 109 yrs for the low temperature gas, a mass accretion rate of approximately 300 Mo/yr and a characteristic size of 10 to 20 Kpc for the cool gas. The Fe abundance in the core, approximately 0.4, is similar to the Fe abundance averaged over the whole cluster indicating that Fe emission is not strongly concentrated about NGC 1275. The Si and S abundances are consistent with solar values.

Mushotzky, R. F.↗

Observation of the core of the Perseus cluster with the Einstein solid state spectrometer - Cooling gas and elemental abundances

Solid State Spectrometer observations of the core of the Perseus cluster have resulted in the detection of X-ray emission lines due to Si, S, and Fe. Analysis of the spectrum indicates that the X-ray emission has at least two characteristic temperatures. This is interpreted in the framework of radiative accretion in the core of the cluster. The derived parameters are a cooling time less than or approximately equal to 2 x 10 to the ninth years for the low-temperature gas, a mass accretion rate of approximately 300 solar masses per year, and a characteristic size of 10-20 kpc for the cool gas. The Fe abundance in the core (approximately 0.4) is similar to the Fe abundance averaged over the whole cluster, indicating that Fe emission is not strongly concentrated about NGC 1275. The Si and S abundances are consistent with solar values.

Mushotzky, R. F.↗

The 20 GHz spacecraft FET solid state transmitter

The engineering development of a solid state transmitter amplifier operating in the 20 GHz frequency band using GaAs field effect transistors (FETs) was detailed. The major efforts include GaAs FET device development, single-ended amplifier stage, balanced amplifier stage, cascaded stage and radial combiner designs, and amplifier integration and test. A multistage GaAs FET amplifier capable of 8.2 W CW output over the 17.9 to 19.1 GHz frequency band was developed. The GaAs FET devices developed represent state of the art FET power device technology. Further device improvements are necessary to increase the bandwidth to 2.5 GHz, improve dc-to-RF efficiency, and increase power capability at the device level. Higher power devices will simplify the amplifier combining scheme, reducing the size and weight of the overall amplifier.

Source record↗

High-efficiency solid state power amplifier

A high-efficiency solid state power amplifier (SSPA) for specific use in a spacecraft is provided. The SSPA has a mass of less than 850 g and includes two different X-band power amplifier sections, i.e., a lumped power amplifier with a single 11-W output and a distributed power amplifier with eight 2.75-W outputs. These two amplifier sections provide output power that is scalable from 11 to 15 watts without major design changes. Five different hybrid microcircuits, including high-efficiency Heterostructure Field Effect Transistor (HFET) amplifiers and Monolithic Microwave Integrated Circuit (MMIC) phase shifters have been developed for use within the SSPA. A highly efficient packaging approach enables the integration of a large number of hybrid circuits into the SSPA.

Wallis, Robert E.↗

Solid-State Nuclear Power

A strategy for "Solid-State" Nuclear Power is proposed to guide development of technologies and systems into the second 50 years of nuclear spaceflight. The strategy emphasizes a simple and highly integrated system architecture with few moving parts or fluid loops; the leverage of modern advances in materials, manufacturing, semiconductors, microelectromechanical and nanotechnology devices; and the targeted advancement of high temperature nuclear fuels, materials and static power conversion to enable high performance from simple system topologies.

George, Jeffrey A.↗

Solid-State Spectral Light Source System

A solid-state light source combines an array of light-emitting diodes (LEDs) with advanced electronic control and stabilization over both the spectrum and overall level of the light output. The use of LEDs provides efficient operation over a wide range of wavelengths and power levels, while electronic control permits extremely stable output and dynamic control over the output. In this innovation, LEDs are used instead of incandescent bulbs. Optical feedback and digital control are used to monitor and regulate the output of each LED. Because individual LEDs generate light within narrower ranges of wavelengths than incandescent bulbs, multiple LEDs are combined to provide a broad, continuous spectrum, or to produce light within discrete wavebands that are suitable for specific radiometric sensors.

Maffione, Robert↗

Introduction to the Solid State Based Interior Lighting System for ISS

Solid state lighting assembly (SSLA) were designed to replace general luminaire assembly (GLA) for both general interior illumination and improved circadian rhythm through melatonin control using multiple spectrums. To accomplish these goals, the light is design to operate in 3 modes with 3 distinct spectrum. The different spectrum provide control of the blue portion of the light which impacts melatonin production in humans which impacts sleep. General mode is a 4500K "neutral" light spectrum intended to the be the default mode of operation for day to day operations. Pre-sleep mode is a 2700K "warm" light spectrum intended to be used by the crew at the end of the work day. Phase-shift mode is a 6500K "cool" light spectrum intended to be used for altering the crew's sleep patterns.

Maida, James C.↗

Solid state transport-based thermoelectric converter

A solid state thermoelectric converter includes a thermally insulating separator layer, a semiconducting collector and an electron emitter. The electron emitter comprises a metal nanoparticle layer or plurality of metal nanocatalyst particles disposed on one side of said separator layer. A first electrically conductive lead is electrically coupled to the electron emitter. The collector layer is disposed on the other side of the separator layer, wherein the thickness of the separator layer is less than 1 .mu.m. A second conductive lead is electrically coupled to the collector layer.

36 MATERIALS SCIENCE↗

2018 DOE Solid-State Lighting Project Portfolio

The 2018 Solid-State Lighting Project Portfolio provides an overview of all SSL projects that have been funded by DOE since 2000. Projects that were active during 2017 are found in the main body of this report, and all historic projects can be found in the appendix. Within these sections, project profiles are sorted by technology type (i.e., LED or OLED) and then by performer name. A profile is provided on each project. Each profile includes a brief technical description, as well as information about project partners, funding, and the research period. This report is updated annually, although the research described in the Portfolio changes periodically as new projects are initiated and existing ones are concluded.

SSL, lighting, project, LED, OLED, portfolio, awar↗

High-performance all-solid-state batteries enabled by salt bonding to perovskite in poly(ethylene oxide)

Flexible and low-cost poly(ethylene oxide) (PEO)-based electrolytes are promising for all-solid-state Li-metal batteries because of their compatibility with a metallic lithium anode. However, the low room-temperature Li-ion conductivity of PEO solid electrolytes and severe lithium-dendrite growth limit their application in high-energy Li-metal batteries. Here we prepared a PEO/perovskite Li 3/8 Sr 7/16 Ta 3/4 Zr 1/4 O 3 composite electrolyte with a Li-ion conductivity of 5.4 × 10 −5 and 3.5 × 10 −4 S cm −1 at 25 and 45 °C, respectively; the strong interaction between the F − of TFSI − (bis-trifluoromethanesulfonimide) and the surface Ta 5+ of the perovskite improves the Li-ion transport at the PEO/perovskite interface. A symmetric Li/composite electrolyte/Li cell shows an excellent cyclability at a high current density up to 0.6 mA cm −2 . A solid electrolyte interphase layer formed in situ between the metallic lithium anode and the composite electrolyte suppresses lithium-dendrite formation and growth. All-solid-state Li|LiFePO 4 and high-voltage Li|LiNi 0.8 Mn 0.1 Co 0.1 O 2 batteries with the composite electrolyte have an impressive performance with high Coulombic efficiencies, small overpotentials, and good cycling stability.

25 ENERGY STORAGE↗

Practically Accessible All-Solid-State Batteries Enabled by Organosulfide Cathodes and Sulfide Electrolytes

The combination of organic electrode materials and sulfide electrolytes is expected to enable the development of all-solid-state organic batteries featuring high energy density and long-term sustainability. In this work, thiuram hexasulfide is reported as a low-cost and high-capacity organic cathode for solid-state batteries based on sulfide electrolytes, delivering a capacity of ~600 mAh g -1 and retaining 80.8 % capacity after 500 cycles. An electrochemically reversible change of the cathode interface was revealed upon cycling. Full cell displays an oscillating stress change up to 0.6 MPa during cycling, predominated by the anode side. The energy density is 1140 Wh kg -1 at the material level and 376 Wh kg -1 at the electrode level, which are among the best-reported organic cathodes to date. A high areal capacity of 10.4 mAh cm -2 is reached with a high mass loading cathode. A dry-film approach is further explored to manufacture sheet-type cells. Free-standing electrolyte film is merely ~48 μm thick and demonstrates an ultralow areal resistance of 3.9 Ω cm 2 , significantly boosts the cell-level energy density and reduces the cell internal resistance.

25 ENERGY STORAGE↗

Full differentiation and assignment of boron species in the electrolytes Li{sub 2}B{sub 6}O{sub 9}F{sub 2} and Li{sub 2}B{sub 3}O{sub 4}F{sub 3} by solid-state {sup 11}B NMR spectroscopy

The syntheses of two new fluorooxoborates, Li{sub 2}B{sub 3}O{sub 4}F{sub 3} and Li{sub 2}B{sub 6}O{sub 9}F{sub 2}, which possess considerable ion conductivity at higher temperatures, have been reported recently. Here, we describe the characterisation of these compounds by solid-state {sup 11}B NMR spectroscopy. The complex central-transition MAS spectra, resulting from overlap of sub-spectra contributed by the individual boron species in the crystal structures, could be clearly separated by acquisition and analysis of 3QMAS spectra. By numerical fit of these sub-spectra, the isotropic chemical shift {delta}{sub iso}, the quadrupolar coupling constant {chi}, and the asymmetry {eta} were determined. Using known relations between boron coordination and chemical shift as well as quadrupolar coupling, the individual {sup 11}B NMR resonances have been ascribed to boron species in tetrahedral or trigonal environment. To remove remaining assignment ambiguities, the response of the {sup 11}B resonances to {sup 19}F decoupling was qualitatively analysed. Thus, by using the combined information conveyed by chemical shift, quadrupolar and dipolar interaction, a complete assignment of the complex {sup 11}B line shapes exhibited by the fluorooxoborates has been achieved. - Graphical abstract: Structure and solid-state {sup 11}B NMR spectrum of Li{sub 2}B{sub 3}O{sub 4}F{sub 3}. Highlights: Black-Right-Pointing-Pointer Characterisation of title compounds by solid-state {sup 11}B NMR spectroscopy. Black-Right-Pointing-Pointer Sub-spectra of boron species separated by evaluation of 3QMAS spectra. Black-Right-Pointing-Pointer Isotropic chemical shift and quadrupolar interaction parameters determined. Black-Right-Pointing-Pointer Full boron assignment based on NMR parameters and response to {sup 19}F decoupling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Liquid-like dynamics in a solid-state lithium electrolyte

Superionic materials represent a regime intermediate between the crystalline and liquid states of matter. Despite the considerable interest in potential applications for solid-state batteries or thermoelectric devices, it remains unclear whether the fast ionic diffusion observed in superionic materials reflects liquid-like dynamics or whether the hops of mobile ions are inherently coupled to more conventional lattice phonons. Here we reveal a crossover from crystalline vibrations to relaxational dynamics of ionic diffusion in the superionic compound Li 6 PS 5 Cl, a candidate solid-state electrolyte. By combining inelastic and quasi-elastic neutron-scattering measurements with first-principles-based machine-learned molecular dynamics simulations, we found that the vibrational density of states in the superionic state strongly deviates from the quadratic behaviour expected from the Debye law of lattice dynamics. The superionic dynamics emerges from overdamped phonon quasiparticles to give rise to a linear density of states characteristic of instantaneous normal modes in the liquid state. Further, we showed that the coupling of lattice phonons with a dynamic breathing of the Li+ diffusion bottleneck enables an order-of-magnitude increase in diffusivity. Thus, our results shed insights into superionics for future energy storage and conversion technologies.

25 ENERGY STORAGE↗

Solid-State Ultracapacitor for Improved Energy Storage

NASA's Marshall Space Flight Center has developed a solid-state ultracapacitor using a novel nanocomposite, dielectric material. The material's design is based on the internal barrier layer capacitance (IBLC) concept, and it uses novel dielectric and metallic conductive ink formulations. Novel processing methods developed by NASA provide for unique dielectric properties at the grain level. Nanoscale raw material powders are tailored using a variety of techniques and then formulated into a special ink. This dielectric ink is used with novel metallic conductive ink to print a capacitor layer structure into any design necessary to meet a range of technical requirements. The innovation is intended to replace current range safety batteries that NASA uses to power the systems that destroy off-course space vehicles. A solid-state design provides the needed robustness and safety for this demanding application.

Nabors, Sammy↗

Surface Termination of CsPbBr 3 Perovskite Quantum Dots Determined by Solid-State NMR Spectroscopy

Cesium lead halide perovskite quantum dots (QDs) have gained significant attention as next-generation optoelectronic materials; however, their properties are highly dependent on their surface chemistry. The surfaces of cuboidal CsPbBr 3 QDs have been intensively studied by both theoretical and experimental techniques, but fundamental questions still remain about the atomic termination of the QDs. The surface binding sites and modes of ligands at the surface remain unproven. Herein, we demonstrate that solid-state NMR spectroscopy allows the unambiguous assignment of organic surface ligands via 1 H, 13 C, and 31 P NMR. Surface-selective 133 Cs solid-state NMR spectra show the presence of an additional 133 Cs NMR signal with a unique chemical shift that is attributed to Cs atoms terminating the surface of the particle and which are likely coordinated by carboxylate ligands. Dipolar dephasing curves that report on the distance between the surface ammonium ligands and Cs and Pb were recorded using double resonance 1 H{ 133 Cs} and 1 H{ 207 Pb} RESPDOR experiments. Model QD surface slabs with different possible surface terminations were generated from the CsPbBr 3 crystal structure and theoretical RESPDOR dipolar dephasing curves considering all possible 1 H- 133 Cs/ 207 Pb spin pairs were then calculated. Comparison of the calculated and experimental RESPDOR curves indicates the particles are CsBr terminated (not PbBr 2 terminated) with alkylammonium ligands substituting into some surface Cs sites, consistent with the surface-selective 133 Cs NMR experiments. Lastly, these results highlight the utility of high-resolution solid-state NMR spectroscopy for studying ligand binding and the surface structure of nanomaterials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A mathematical model of solid-state dewetting of barium thin films on W (112)

Solid state dewetting occurs when a thin solid film is heated. The temperature of dewetting depends on the thickness of the film; dewetting can be observed in the range of 1/3 to 1/2 of the bulk melting temperature. While remaining solid, the film behaves in a manner similar to liquids dewetting and agglomerating to forming islands or droplets. One of the possible mechanisms is the conversion of a metastable thin film geometry into a more stable form. Heating the metastable film gives the film atoms higher mobility, and the films retract, dewetting the surface. This atomic motion can be restricted due to surface anisotropy. Herein we present in situ emission microscopy observations of barium thin films deposited onto W (112) by thermal evaporation. From the modeling viewpoint, the evolution of the film in this system could be divided in four stages: (i) the nucleation and growth of the thin film as a simply connected region; (ii) formation of droplets/islands/hillocks; (iii) nucleation of holes; (iv) evolution of the components of the disconnected film to their equilibrium state. We present a continuum model that is qualitatively consistent with the evolution of the film observed at the initial stage of the experiment and discuss the later stages of the evolution of surface structures.

36 MATERIALS SCIENCE↗