Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scattering functions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

The solar occultation technique for remote sensing of particulates in the earth's atmosphere. I - The inversion of horizon radiances from space

The aerosol scattering coefficient as a function of height can be recovered from a direct inversion of the single-scattering horizon radiance provided the sun is above the horizon and an independent measurement of extinction as a function of height is made. Aerosol detection is effected by means of spacecraft measurements of the horizon radiance made during periods of spacecraft twilight. A solar occultation technique which allows the twilight measurements to be made when the sun is still above the horizon greatly reduces the complexity of the inversion problem. The second part of the paper reports on the use of a coronograph aboard Skylab to photograph the horizon just before spacecraft twilight in order to monitor the aerosol component above the tropopause. The coronograph picture, centered on 26.5 degrees E longitude and 63.0 degrees S latitude, shows that the aerosol layer peaks at a height of 48 plus or minus 1 km.

Schuerman, D. W.↗

Scattering of Low Energy Electrons and Positrons from Hydrogenic Systems and Applications

While the electron scatters from the target, the target no longer stays in its original form. One of the first methods to take into account the distortion of the target at low incident energies is the method of polarized orbitals. In this method the wave function for the process is written using the first-order perturbation theory and the equation for the scattering function is derived from the Schradinger equation. This method has been very successful in calculating the phase shifts and therefore the cross sections at various energies. The total wave function can be used to calculate photoionization cross sections. The disadvantage of this approach is that the method is not variational and therefore does not provide bounds on the phase shifts. These difficulties can be overcome by using the Feshbach projection operator formalism. This approach has been employed for the scattering of electrons and positrons from targets. Results of various calculations will be discussed.

Bhatia, Anand K.↗

A novel methodology for radiative transfer in a planetary atmosphere. I - The functions a exponent m and b exponent m of anisotropic scattering

The original problem of anisotropic scattering in an atmosphere illuminated by a unidirectional source is replaced by an analogous formulation where the incident light is omnidirectional. A radiative-transfer equation for the omnidirectional case is obtained in which the direction of illumination plays no role and the source-function analog, Sobolev's (1972) source function Phi exponent m, contains only a single integral term. For radiation incident on the top or the bottom of the atmosphere, this equation involves the functions b exponent m and h exponent m, respectively, with m corresponding to the order of the harmonic component of the scattered radiation field; these two functions are shown to be only one through some simple reciprocity relations. The transfer problem is then reformulated for the function a exponent m, in which case the source-function analog (Sobolev's function D exponent m) involves incident direction.

Fymat, A. L.↗

Validity of the scattering-length approximation in strongly interacting Fermi systems

We investigate the energy spectrum of systems of two, three, and four spin-(1/2) fermions with short range attractive interactions both exactly and within the scattering length approximation. The formation of molecular bound states and the ferromagnetic transition of the excited scattering state are examined systematically as a function of the two-body scattering length. Identification of the upper branch (scattering states) is discussed and a general approach valid for systems with many particles is given. We show that an adiabatic ferromagnetic transition occurs, but at a critical transition point k{sub F}a much higher than predicted from previous calculations, almost all of which use the scattering length approximation. In the four-particle system the discrepancy is a factor of 2. The exact critical interaction strength calculated in the four-particle system is consistent with that reported by experiment. To make comparisons with the adiabatic transition, we study the quench dynamics of the pairing instability using the eigenstate wave functions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sound velocity and density of magnesiowüstites: Implications for ultralow-velocity zone topography

Herein we explore the effect of Mg/Fe substitution on the sound velocities of iron-rich (Mg 1 - x Fe x )O, where x = 0.84, 0.94, and 1.0. Sound velocities were determined using nuclear resonance inelastic X-ray scattering as a function of pressure, approaching those of the lowermost mantle. The systematics of cation substitution in the Fe-rich limit has the potential to play an important role in the interpretation of seismic observations of the core-mantle boundary. By determining a relationship between sound velocity, density, and composition of (Mg,Fe)O, this study explores the potential constraints on ultralow-velocity zones at the core-mantle boundary.

58 GEOSCIENCES↗

Additive‐Free, Low‐Temperature Crystallization of Stable α‐FAPbI 3 Perovskite

Abstract Formamidinium lead triiodide (FAPbI 3 ) is attractive for photovoltaic devices due to its optimal bandgap at around 1.45 eV and improved thermal stability compared with methylammonium‐based perovskites. Crystallization of phase‐pure α‐FAPbI 3 conventionally requires high‐temperature thermal annealing at 150 °C whilst the obtained α‐FAPbI 3 is metastable at room temperature. Here, aerosol‐assisted crystallization (AAC) is reported, which converts yellow δ‐FAPbI 3 into black α‐FAPbI 3 at only 100 °C using precursor solutions containing only lead iodide and formamidinium iodide with no chemical additives. The obtained α‐FAPbI 3 exhibits remarkably enhanced stability compared to the 150 °C annealed counterparts, in combination with improvements in film crystallinity and photoluminescence yield. Using X‐ray diffraction, X‐ray scattering, and density functional theory simulation, it is identified that relaxation of residual tensile strains, achieved through the lower annealing temperature and post‐crystallization crystal growth during AAC, is the key factor that facilitates the formation of phase‐stable α‐FAPbI 3 . This overcomes the strain‐induced lattice expansion that is known to cause the metastability of α‐FAPbI 3 . Accordingly, pure FAPbI 3 p–i–n solar cells are reported, facilitated by the low‐temperature (≤100 °C) AAC processing, which demonstrates increases of both power conversion efficiency and operational stability compared to devices fabricated using 150 °C annealed films.

36 MATERIALS SCIENCE↗

Stabilizing the Solid‐Electrolyte Interphase with Polyacrylamide for High‐Voltage Aqueous Lithium‐Ion Batteries

Abstract The introduction of “water‐in‐salt” electrolyte (WiSE) concept opens a new horizon to aqueous electrochemistry that is benefited from the formation of a solid‐electrolyte interphase (SEI). However, such SEI still faces multiple challenges, including dissolution, mechanical damaging, and incessant reforming, which result in poor cycling stability. Here, we report a polymeric additive, polyacrylamide (PAM) that effectively stabilizes the interphase in WiSE. With the addition of 5 molar % PAM to 21 mol kg −1 LiTFSI electrolyte, a LiMn 2 O 4 ∥L‐TiO 2 full cell exhibits enhanced cycling stability with 86 % capacity retention after 100 cycles at 1 C. The formation mechanism and evolution of PAM‐assisted SEI was investigated using operando small angle neutron scattering and density functional theory (DFT) calculations, which reveal that PAM minimizes the presence of free water molecules at the anode/electrolyte interface, accelerates the TFSI − anion decomposition, and densifies the SEI.

Hou, Xu↗

Donor-fullerene dyads for energy cascade organic solar cells

Organic bulk hetero junction (BHJ) solar cells require broad absorption of the incident solar spectrum by the donor and acceptor in the blend. Fullerene derivatives with covalently linked dyes, referred to as dyads, were designed to have strong optical absorption and appropriate electronic levels for electron transfer with common donor polymers in BHJs. Dyads with dyes based on diketopyrrolopyrrole and benzothiadiazole were synthesized using either a methanofullerene or a fulleropyrrolidine linkage. Here, the performance of these dyad acceptors in BHJ solar cells with poly(3-hexylthiophene) (P3HT) and a low optical gap co-polymer of thiophene and diketopyrrolopyrrole (PDPP2FT) were examined. Although the solar power conversion efficiencies were low, charge generation from the molecular dye in the dyad could be observed in BHJs with PDPP2FT. The low power conversion efficiency was attributed to the morphology of the BHJs based on grazing incidence wide angle X-ray scattering patterns. Density functional theory was used to examine the charge transfer states between the donor and the dyad. The lowest energy charge-transfer state was found to be a transition from the donor polymer to the fullerene portion of the dyad.

14 SOLAR ENERGY↗

Excited State Electronic Properties of Sodium Iodide and Cesium Iodide

We compute from first principles the dielectric function, loss function, lifetime and scattering rate of quasiparticles due to electronic losses, and secondary particle spectrum due to plasmon decay in two scintillating alkali halides, sodium iodide and cesium iodide. Particular emphasis is placed on quasiparticles within several multiples of the band gap from the band edges. A theory for the decay spectra of plasmons and other electronic excitations in crystals is presented. Applications to Monte Carlo radiation transport codes are discussed.

Campbell, Luke W↗

Hydrogen motion in near stoichiometric yttrium dihydride at elevated temperatures

The high-temperature motion of hydrogen in near stoichiometric yttrium dihydride (YH x , x = 1.62 and 1.87 at.%) was investigated using incoherent quasi-elastic neutron scattering and Density Functional Theory (DFT) calculations as a function of hydrogen stoichiometry. Translational motion (diffusivity) of hydrogen in yttrium dihydride was only observed in a temperature range of 1073–1173 K under vacuum environment. Here, the hydrogen motion was found to be limited to the tetrahedral sublattice, and diffusivity of hydrogen was observed to increase with decreasing hydrogen stoichiometry. The same behavior was also supported with DFT calculations. The DFT results also indicated that certain migration paths with smaller energy barriers favored H jump resulting in higher diffusivities.

08 HYDROGEN↗

The separatrix electron density in JET, ASDEX upgrade and alcator C-Mod H-mode plasmas: A common evaluation procedure and correlation with engineering parameters

The separatrix electron density is an important parameter for core-edge scenario integration in tokamak devices, as it influences plasma confinement, divertor detachment and disruption avoidance. This quantity has been measured in H-mode discharges on JET, ASDEX Upgrade and Alcator C-Mod by applying the same fitting function to Thomson scattering measurements, and by employing the same analysis technique based on scrape-off layer power balance. To estimate the power crossing the separatrix, the inter-ELM time derivative of the plasma energy d W /d t has been experimentally evaluated and found to be approximately a constant fraction of the absorbed heating power. Correlations between n e,sep and engineering parameters have been investigated, revealing that n e,sep scales with the divertor neutral pressure p 0,div in a similar manner across all devices. Additionally, when n e,sep is normalized to the obtained n e,sep dependency, no clear correlation with the plasma current is found. These observations are in agreement with the 2-point model, which suggests that the upstream separatrix density is mainly set by the recycling at the divertor target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Charm and bottom hadrons in hot hadronic matter

Heavy quarks, and the hadrons containing them, are excellent probes of the QCD medium formed in high-energy heavy-ion collisions, as they provide essential information on the transport properties of the medium and how quarks color-neutralize into hadrons. Large theoretical and phenomenological efforts have been dedicated thus far to assess the diffusion of charm and bottom quarks in the quark–gluon plasma and their subsequent hadronization into heavy-flavor (HF) hadrons. However, the fireball formed in heavy-ion collisions also features an extended hadronic phase, and therefore any quantitative analysis of experimental observables needs to account for the rescattering of charm and bottom hadrons. This is further reinforced by the presence of a QCD cross-over transition and the notion that the interaction strength is maximal in the vicinity of the pseudo-critical temperature. We review existing approaches for evaluating the interactions of open HF hadrons in a hadronic heat bath and the pertinent results for scattering amplitudes, spectral functions and transport coefficients. While most of the work to date has focused on D -mesons, we also discuss excited states as well as HF baryons and the bottom sector. Both the HF hadro-chemistry and bottom observables will play a key role in future experimental measurements. We also conduct a survey of transport calculations in heavy-ion collisions that have included effects of hadronic HF diffusion and assess its impact on various observables.

effective field theories↗

Polyaspartic Acid Concentration Controls the Rate of Calcium Phosphate Nanorod Formation in High Concentration Systems

Polyelectrolytes are known to greatly affect calcium phosphate (CaP) mineralization. The reaction kinetics as well as the CaP phase, morphology and aggregation state depend on the relative concentrations of the polyelectrolyte and the inorganic ions in a complex, nonlinear manner. This study examines the structural evolution and kinetics of polyaspartic acid (pAsp) directed CaP mineralization at high concentrations of polyelectrolytes, calcium, and total phosphate (19–30 mg/mL pAsp, 50–100 mM Ca 2+ , Ca/P = 2). Using a novel combination of characterization techniques including cryogenic transmission electron microscopy (cryo-TEM), spectrophotometry, X-ray total scattering pair distribution function analysis, and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), it was determined that the CaP mineralization occurred over four transition steps. The steps include the formation of aggregates of pAsp stabilized CaP spherical nanoparticles (sNP), crystallization of sNP, oriented attachment of the sNP into nanorods, and further crystallization of the nanorods. The intermediate aggregate sizes and the reaction kinetics were found to be highly polymer concentration dependent while the sizes of the particles were not concentration dependent. Furthermore, this study demonstrates the complex role of pAsp in controlling the mechanism as well as the kinetics of CaP mineralization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vibrations and Phase Stability in Mixed Valence Antimony Oxide

α-Sb 2 O 4 (cervantite) and β-Sb 2 O 4 (clinocervantite) are mixed valence compounds with equal proportions of Sb III and Sb V as represented in the formula Sb III Sb V O 4 . Their structure and properties can be difficult to calculate owing to the Sb III lone-pair electrons. Here, we present a study of the lattice dynamics and vibrational properties using a combination of inelastic neutron scattering, Mössbauer spectroscopy, nuclear inelastic scattering, and density functional theory (DFT) calculations. DFT calculations that account for lone-pair electrons match the experimental densities of phonon states. Mössbauer spectroscopy reveals the β phase to be significantly harder than the α phase. Calculations with O vacancies reveal the possibility for nonstoichiometric proportions of Sb III and Sb V in both phases. An open question is what drives the stability of the α phase over the β phase, as the latter shows pronounced kinetic stability and lower symmetry despite being in the high-temperature phase. Since the vibrational entropy difference is small, it is unlikely to stabilize the α phase. In conclusion, our results suggest that the α phase is more stable only because the material is not fully stoichiometric.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Non-Altermagnetic Origin of Exchange Bias Behaviors in Incoherent RuO 2 /Fe Bilayer Heterostructures

Initially identified as a promising altermagnetic (AM) candidate, rutile RuO 2 has since become embroiled in controversy due to contradictory findings of modeling and measurements of the magnetic properties of bulk crystals and thin films. For example, despite observations of a bulk nonmagnetic state using density functional theory, neutron scattering, and muon spin resonance measurements, patterned RuO 2 Hall bars and film heterostructures display magnetotransport signatures of magnetic ordering. Among the characteristics routinely cited as evidence for AM is the observation of exchange bias (EB) in an intimately contacted Fe-based ferromagnetic (FM) layer, which can arise due to interfacial coupling with a compensated antiferromagnet. Here, within this work, the origins of this EB coupling in Ru-capped RuO 2 /Fe bilayers are investigated using polarized neutron diffraction, polarized neutron reflectometry, cross-sectional transmission electron microscopy, and super conducting quantum interference device measurements. These experiments reveal that the EB behavior is driven by the formation of an iron oxide interlayer containing Fe 3 O 4 that undergoes a magnetic transition and pins interfacial moments within Fe at low temperature. These findings are confirmed by comparable measurements of Ni-based heterostructures, which do not display EB coupling, as well as magnetometry of additional Fe/Ru bilayers that display oxide-driven EB coupling despite the absence of the epitaxial RuO 2 layer. While these results do not directly refute the possibility of AM ordering in RuO 2 thin films, they reveal that EB, and related magnetotransport phenomena, cannot alone be considered evidence of this characteristic in the rutile structure due to interfacial chemical disorder.

RuO2↗

Reactivity of Hydrogen on and in Nanostructured Molybdenum Nitride: Crotonaldehyde Hydrogenation

Early-transition-metal nitrides, including γ-Mo 2 N, are active and selective for a variety of reactions, including the hydrogenation of organics (e.g., hydrodeoxygenation), CO (e.g., Fischer–Tropsch synthesis), and CO 2 . In addition to adsorbing hydrogen onto the surface, some of these materials can incorporate hydrogen into subsurface, interstitial sites. Research described in this paper examined, experimentally and computationally, the nature of hydrogen on and in γ-Mo 2 N, with a particular focus on characterizing the interactions of these hydrogens with crotonaldehyde. Hydrogen was added to γ-Mo 2 N via exposure to gaseous hydrogen at elevated temperatures, forming γ-Mo 2 N-H x , where 0.061< x < 0.082. Temperature-programmed desorption (TPD) experiments indicate that γ-Mo 2 N-H x has at least two distinct hydrogen binding sites and that these sites can be selectively populated. Inelastic neutron scattering and density functional theory calculations indicate the presence of surface nitrogen-bound (κ 1 -NH surf ), surface Mo-bound (κ 1 -MoHsurf), and interstitial Mo-bound (μ 6 -Mo 6 H sub ) hydrogens. Selectivities for the hydrogenation of crotonaldehyde, a model of species in biomass-derived liquids, correlated with the populations at these sites. Importantly, materials with high densities of interstitial, hydridic hydrogen were selective for C=O hydrogenation (i.e., formation of crotyl alcohol). Collectively the results provide mechanistic insights regarding the desorption and reactivity of hydrogen on and in γ-Mo 2 N. Hydrogen adsorption/desorption to γ-Mo 2 N is heterolytic; in particular, H 2 adds across a Mo–N bond. Because the surface Mo–H site is energetically unfavorable in comparison to the interstitial site, hydrogen migrates into interstitial sites once the surface NH sites are saturated. Crotonaldehyde adsorption facilitates migration of this interstitial hydrogen back to the surface, forming surface Mo–H that is selective for hydrogenation of the C=O bond. These insights will facilitate the design of γ-Mo 2 N and other early-transition-metal nitrides for catalytic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗