Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resistivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Effect of Different Zirconium Contents on the Corrosion Resistance of ZrO{sub 2}-TiO{sub 2} Film-Coated Stainless Steel

This work discusses the corrosion resistance of x%zirconia (ZrO{sub 2})–x%titania (TiO{sub 2}) nanocomposite films with different percentages of ZrO{sub 2} prepared on stainless steel by dipping the substrates in sol–gel solutions. The phase compositions and microstructures of the films were investigated by x-ray diffraction (XRD) and scanning electron microscopy (SEM). Tafel polarization curves and electrochemical impedance spectroscopy (EIS) were employed to investigate the corrosion resistance of the coated steel substrates during immersion in a 5% NaCl solution at room temperature. The results showed that when the percentage of ZrO{sub 2} in the sol–gel was relatively low, the film contained cracks, leading to a poor corrosion resistance. When the percentage of ZrO{sub 2} was higher, the corrosion resistance of the film was also affected by the sintering temperature; a sintering temperature of 650 °C gave the best protection of the metal surface, and the protection efficiency was 95%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Improved Corrosion Resistance of Ni-Co Coatings Prepared by Electrodeposition with Large Centrifugal Acceleration

A higher Co content in Ni-Co coatings leads to better corrosion resistance to a certain degree. In this paper, centrifugal acceleration was introduced in the electrodeposition of Ni-Co coatings in order to obtain improved Ni-Co coatings with high Co content. With different centrifugal accelerations, the Co content, morphology, preferred coating orientation, microhardness, and wear and corrosion resistance were examined. Under large centrifugal acceleration, a maximal Co content of 38.25% was obtained according to the EDS results, which was higher than that obtained using normal electrodeposition. The SEM images indicated that the morphology of the prepared Ni-Co coatings with the highest Co content was smoothened. In addition, the microhardness of Ni-Co coatings with increased Co content was improved to about 530HV, which was hardly achieved under normal electrodeposition. Most of all, based on the polarization curve and EIS results, the corrosion resistance was significantly enhanced as the Co content reached the maximum. In general, corrosion resistance of the deposited Ni-Co coatings can be improved with large centrifugal acceleration.

36 MATERIALS SCIENCE↗

Influence of Ti and REE on Primary Crystallization and Wear Resistance of Chromium Cast Iron

The article presents the results of primary crystallization, wear resistance and SEM studies of chromium cast iron inoculated with ferrotitanium and rare earth elements as a mischmetal inoculating mixture. Thermal-derivative analysis method was used to conduct studies of primary crystallization in two types of testers, namely ATD-C and ATD-Is, reflecting two different cooling speeds. Wear resistance tests were performed with the use of modified pin-on-disk method on Tribotester 3-POD device, where the samples were moving in circular motion in metal-mineral friction system. Silicon carbide was used as a counter sample. The studies allowed to determine the influence of selected inoculants on the microstructure and wear resistance of the studied samples. All characteristic crystallization temperatures of samples casted into ATD-Is testers increased, as well as wear resistance of each inoculated samples compared to the non-inoculated sample. It was proven that TiC and REE compounds are effective inoculants for chromium carbides and that REE compounds can work as underlay for TiC crystallization.

36 MATERIALS SCIENCE↗

Relationship Between Microstructure and Marine Corrosion Resistance of Martensitic Stainless Steels: A Multiscale Approach

The electrochemical properties of martensitic stainless steels may depend on complex aspects of their microstructure. Three alloys were considered in this study: X30Cr13 (AISI 420), a martensitic stainless steel with a low content of alloying elements; X17CrNi16-2 (AISI 431), chosen for its strong resistance to corrosion; and X5CrNiCu15-5 (AISI 630), chosen for its good mechanical resistance. Voltammetry tests have shown the influence of carbon and chromium content on corrosion resistance. Resistance to pitting appears equivalent for the both. However, heterogeneous corrosion, in relation to δ-ferrite precipitation and chromium carbides at the lath boundaries, appears in the case of X17CrNi16-2. Conversely, non-preferential corrosion occurs in the case of the X5CrNiCu15-5, and a superior passive film stability during immersion in artificial seawater. This counterbalance negative effect of the microstructure. Thus, it achieves an equivalent “macroscopically” corrosion behavior between the two steels.

36 MATERIALS SCIENCE↗

Investigation into the Wear and Dent Resistance of Ni/Ti Nanolaminates and Superelastic NiTi Coating

Metallic wear-resistant coatings, such as chromium based, are desired to prevent premature failure of working parts and are widely used in the oil and gas and aerospace industries. These coatings are extremely hard; however, researchers have found that an optimal coating will also be resilient. Bulk NiTi possesses a superelasticity effect that can provide wear resistance to parts that will experience impact, wear, and erosion daily. Yet, NiTi as a surface coating has not been fully exploited in industrial applications. Bulk NiTi production presents significant challenges, such as poor formability and machinability. This study attempts to fabricate NiTi through a heat treatment process of sputter-deposited alternating nanosized Ni and Ti layers. After annealing, the nanolaminate coatings contained the austenitic NiTi phase. The elastic modulus to hardness ratio and wear resistance showed that the nanolaminate annealed at 650 °C is comparable to the sputtered superelastic NiTi coating. The annealed nanolaminate coating is found to exhibit higher hardness than the monolayered NiTi, as well as, comparable elastic modulus to hardness values and dent resistance. The findings in this study reveal the superiority of 650 °C annealed nanolaminate NiTi coating over the monolayer NiTi.

36 MATERIALS SCIENCE↗

Molecular dynamics simulation studies of the wild type and E92Q/N155H mutant of Elvitegravir-resistance HIV-1 integrase

Although Elvitegravir (EVG) is a newly developed antiretrovirals drug to treat the acquired immunodeficiency syndrome (AIDS), drug resistance has already been found in clinic, such as E92Q/N155H and Q148H/G140S. Several structural investigations have already been reported to reveal the molecular mechanism of the drug resistance. As full length crystal structure for HIV-1 integrase is still unsolved, we use in this paper the crystal structure of the full length prototype foamy virus (PFV) in complex with virus DNA and inhibitor Elvitegravir as a template to construct the wild type and E92Q/N155H mutant system of HIV-1 integrase. Molecular dynamic simulations was used to revel the binding mode and the drug resistance of the EVG ligand in E92Q/N155H. Several important interactions were discovered between the mutated residues and the residues in the active site of the E92Q/N155H double mutant pattern, and cross correlation and clustering methods were used for detailed analysis. The results from the MD simulation studies will be used to guide the experimental efforts of developing novel inhibitors against drug-resistant HIV integrase mutants.

59 BASIC BIOLOGICAL SCIENCES↗

Linear in temperature resistivity in the limit of zero temperature from the time reparameterization soft mode

The most puzzling aspect of the ‘strange metal’ behavior of correlated electron compounds is that the linear in temperature resistivity often extends down to low temperatures, lower than natural microscopic energy scales. We consider recently proposed deconfined critical points (or phases) in models of electrons in large dimension lattices with random nearest-neighbor exchange interactions. The criticality is in the class of Sachdev–Ye–Kitaev models, and exhibits a time reparameterization soft mode representing gravity in dual holographic theories. We compute the low temperature resistivity in a large M limit of models with SU(M) spin symmetry, and find that the dominant temperature dependence arises from this soft mode. The resistivity is linear in temperature down to zero temperature at the critical point, with a co-efficient universally proportional to the product of the residual resistivity and the co-efficient of the linear in temperature specific heat. We argue that the time reparameterization soft mode offers a promising and generic mechanism for resolving the strange metal puzzle.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The compositional optimization and secondary phases evaluation regarding the creep resistance in Grade 91 steel through the CALPHAD approach

The critical secondary phases along with critical temperatures in regard to the creep resistance of Grade 91 steel alloy were evaluated in order to optimize the composition of the alloy to improve the creep resistance. The critical temperatures which are highlighted in this paper are Ac1 (the threshold temperature in which austinite begins to form), and Ac3 (the threshold temperature at which ferrite is fully transformed into austenite). Furthermore, optimization was presented through various Cr, V, Nb, and N concentrations in Gr.91 in relation to these critical temperatures and the mole fraction of M 23 C 6 , MX, and Z-Phase as critical secondary phases. Here, the results indicate that increasing V and Nb will increase MX stability, whereas decreasing Cr and N lead to a decrease in Z-Phase and M 23 C 6 stability, which may lead to an increased creep resistance of the material. Upon further analyzing the V, Nb, and N concentrations in Gr.91, results indicate that increasing Nb content in the steel can lead to an increased stability of Nb-rich MX2 carbide which can be used to replace Z-Phase in low N steels. Simulation results indicate that elimination of N with a dramatic increase in Nb concentrations result in the stability increase of only M 23 C 6 and MX2 phases at temperature regions between 600 °C and 1370 °C and a complete removal of Z-Phase precipitation. Overall, with the elimination of N, which destabilizes Z-Phase precipitation, and an increase in Nb for NbC carbide stability, a possible solution to increasing both long-term and short-term creep resistance for Gr.91 can be achieved, though further optimization and creep experiments need to be conducted for final conclusions.

36 MATERIALS SCIENCE↗

Niobium addition improves the corrosion resistance of TiHfZrNb x high-entropy alloys in Hanks’ solution

High-strength TiHfZrNb x high-entropy alloys could become the ideal materials for small-diameter endovascular stents once their corrosion resistance in the physiological milieu is confirmed. Here, this work aims at evaluating the corrosion resistance of a TiHfZrNb x high-entropy-alloys family in Hanks’ solution at 37 °C and revealing the influence of niobium on the mechanisms of dissolution and passivation. The alloys were subjected to a series of static and dynamic electrochemical tests and surface characterization, employing the static/dynamic/cyclic polarizations, impedance spectroscopy, XPS, AFM, and SEM. Results confirm a higher corrosion resistance of the alloys compared to that of CP-Ti and Ti6Al4V. The addition of niobium considerably improves the microstructural homogeneity that ensures a low dissolution rate and a greater resistance of the film due to the lower concentration of point defects. The passive film behaves as an n-type semiconductor and is composed of a mixture of TiO 2 , Nb 2 O 5 , ZrO 2 , and HfO 2 oxides, with the presence of metallic hydroxides on the outermost layer. A detailed description of the niobium influence on the mechanisms of the dissolution and passivation is presented in this work.

36 MATERIALS SCIENCE↗

Measuring the maximum capacity and thermal resistances in phase-change thermal storage devices

Thermal energy storage can increase the efficiency of the electric grid by adding flexibility to thermal systems. The value of thermal storage is a function of its energy and power density, which are driven by the capacity and thermal resistances in the storage device. Measuring these properties in-situ at the device level is an important step to understanding the performance and improving the design of thermal storage systems. Here, we present methods to measure the total capacity and thermal resistances in heat exchangers with integrated phase change materials. These methods are demonstrated on two thermal storage devices - a 570-kWh ice-based storage tank and a 0.35-kWh graphite-tetradecane composite device. The results show how thermal resistances evolve with the state of charge and discharge rate in these devices and quantify the impact of applied pressure on the contact resistance in composite phase change material heat exchangers. The proposed method allows for easy comparison between different systems and provides information on the thermal bottlenecks limiting performance. Ultimately, these measurements will allow designers to make robust, high-performance thermal storage devices for next-generation thermal systems.

25 ENERGY STORAGE↗

Corrosion resistance of functionally graded TiN/Ti coatings for proton exchange membrane fuel cells

Bipolar Plates (BPP) are important components of proton exchange membrane fuel cell (PEMFC) stacks. In the development of innovative fuel cell designs, it is advantageous to use aluminum for these applications, however, this material lacks the necessary corrosion resistance. Since the performance of PEMFC stacks depends on BPP properties, in particular, corrosion resistance, depositing titanium nitride (TiN) thin films onto aluminum substrates may improve their efficiency and durability. Present work focuses on improving corrosion resistance and hydrophobicity of TiN/Ti by using N graded films deposited onto aluminum substrates (AA-1100) by grid-assisted magnetron sputtering (GAMS). Electrochemical impedance spectroscopy (EIS) with potentiodynamic and potentiostatic polarization are used to investigate the performance of the substrate/film system at room temperature and 70 oC, thus simulating a prototypic PEMFC electrolyte environment. Electrochemical test results showed that graded TiN films improved corrosion resistance when compared with both the homogeneous films and the AA1100 uncoated substrate. Furthermore, contact angle results reveal improved hydrophobicity for both homogeneous and graded TiN coatings when compared with the AA1100 substrate.

25 ENERGY STORAGE↗

Three-dimensional electrical resistivity model of a nuclear waste disposal site

A three-dimensional (3D) modeling study was completed on a very large electrical resistivity survey conducted at a nuclear waste site in eastern Washington. The acquisition included 47 pole-pole two dimensional (2D) resistivity profiles collected along parallel and orthogonal lines over an area of 850 m×570 m. The data were geo-referenced and inverted using EarthImager3D (EI3D). EI3D runs on a Microsoft 32-bit operating system (e.g. WIN-2K, XP) with a maximum usable memory of 2 GB. The memory limits the size of the domain for the inversion model to 200 m×200 m, based on the survey electrode density. Therefore, a series of increasing overlapping models were run to evaluate the effectiveness of dividing the survey area into smaller subdomains. The results of the smaller subdomains were compared to the inversion results of a single domain over a larger area using an upgraded form of EI3D that incorporates multi-processing capabilities and 32 GB of RAM memory. The contours from the smaller subdomains showed discontinuity at the boundaries between the adjacent models, which do not match the hydrogeologic expectations given the nature of disposal at the site. At several boundaries, the contours of the low resistivity areas close, leaving the appearance of disconnected plumes or open contours at boundaries are not met with a continuance of the low resistivity plume into the adjacent subdomain. The model results of the single large domain show a continuous monolithic plume within the central and western portion of the site, directly beneath the elongated trenches. It is recommended that where possible, the domain not be subdivided, but instead include as much of the domain as possible given the memory of available computing resources.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Bedrock architecture, soil texture, and hyporheic zone characterization combining electrical resistivity and induced polarization imaging

The shallow (<15 m depth) subsurface environment of a short reach along a bedrock stream was investigated with electrical resistivity and induced polarization (IP) to map details of bedrock and soil sediments. The bedrock is mostly comprised of limestone, and is generally resistive compared to the overlying soil. The soil-bedrock interface was determined through a trial and error approach using a sharp boundary feature in the inversion model. The inferred bedrock surface determined from the inversions exhibited undulating patterns with troughs and ridges. A near continuous trough ran alongside the stream within the floodplain, and is suggestive of a paleochannel among other interpretations of this feature. The structure of the electrical resistivity above the bedrock showed small-scale elongated features. The chargeability from the IP method showed larger scale features. High values of chargeability were associated with the sediments in the floodplain, and low values were associated with bedrock, stream, and soil on the elevated banks above the stream. If the chargeability is associated with membrane polarization characteristic of clayey soils, then IP seems to highlight the mere existence of clay, while the resistivity may be more discernable of the relative proportion of clay. Vegetation differences may also explain the chargeability distribution, where parts of the survey with high chargeability had dense pine with no understory making the soils more organically rich.

54 ENVIRONMENTAL SCIENCES↗

Confined Ni-In intermetallic alloy nanocatalyst with excellent coking resistance for methane dry reforming

Carbon dioxide and methane are two main greenhouse gases which are contributed to serious global warming. Fortunately, dry reforming of methane (DRM), a very important reaction developed decades ago, can convert these two major greenhouse gases into value-added syngas or hydrogen. The main problem retarding its industrialization is the seriously coking formation upon the nickel-based catalysts. Herein, a series of confined indium-nickel (In-Ni) intermetallic alloy nanocatalysts (In x Ni@SiO 2 ) have been prepared and displayed superior coking resistance for DRM reaction. The sample containing 0.5 wt.% of In loading (In 0.5 Ni@SiO 2 ) shows the best balance of carbon deposition resistance and DRM reactivity even after 430 h long term stability test. The boosted carbon resistance can be ascribed to the confinement of core–shell structure and to the transfer of electrons from Indium to Nickel in In-Ni intermetallic alloys due to the smaller electronegativity of In. Additionally, both the silica shell and the increase of electron cloud density on metallic Ni can weaken the ability of Ni to activate C–H bond and decrease the deep cracking process of methane. The reaction over the confined InNi intermetallic alloy nanocatalyst was conformed to the Langmuir-Hinshelwood (L-H) mechanism revealed by in situ diffuse reflectance infrared Fourier transform spectroscopy (in-situ DRIFTS). This work provides a guidance to design high performance coking resistance catalysts for methane dry reforming to efficiently utilize these two main greenhouse gases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Acid resistance and corrosion protection potential of concrete prepared with alkali aluminosilicate cement

An experimental investigation was conducted on two key aspects of the durability characteristics of concrete materials prepared with an alkali aluminosilicate hydraulic cement and with Portland cement, both cured at room temperature. The durability characteristics evaluated concerned the acid resistance of concrete, and its ability to protect the embedded reinforcing steel against corrosion under wet-dry cycles. Acid resistance was evaluated through monitoring of mass and strength change over time under acid attack, visual observations, and scanning electron microscopy (SEM). Corrosion resistance was evaluated through measurement of the corrosion potential, visual observations and scanning electron microscopy. The acid resistance and corrosion protection potential of the concrete prepared with the alkali aluminosilicate cement were found to be superior to those of Portland cement concrete.

42 ENGINEERING↗

Moessbauer spectroscopy study on the corrosion resistance of plasma nitrided ASTM F138 stainless steel in chloride solution

Plasma nitriding of ASTM F138 stainless steel samples has been carried out using dc glow discharge under 80% H{sub 2}-20% N{sub 2} gas mixture, at 673 K, and 2, 4, and 7 h time intervals, in order to investigate the influence of treatment time on the microstructure and the corrosion resistance properties. The samples were characterized by scanning electron microscopy, glancing angle X-ray diffraction and conversion electron Moessbauer spectroscopy, besides electrochemical tests in NaCl aerated solution. A modified layer of about 6 {mu}m was observed for all the nitrided samples, independent of nitriding time. The X-ray diffraction analysis shows broad {gamma}{sub N} phase peaks, signifying a great degree of nitrogen supersaturation. Besides {gamma}{sub N,} the Moessbauer spectroscopy results indicated the occurrence of {gamma}' and {epsilon} phases, as well as some other less important phases. Corrosion measurements demonstrate that the plasma nitriding time affects the corrosion resistance and the best performance is reached at 4 h treatment. It seems that the {epsilon}/{gamma}' fraction ratio plays an important role on the resistance corrosion. Additionally, the Moessbauer spectroscopy was decisive in this study, since it was able to identify and quantify the iron phases that influence the corrosion resistance of plasma nitrided ASTM F138 samples.

36 MATERIALS SCIENCE↗

Compensatory islet response to insulin resistance revealed by quantitative proteomics

Compensatory islet response is a distinct feature of the pre-diabetic insulin resistant state in humans and rodents. To identify alterations in the islet proteome that characterize the adaptive response, we analyzed islets from five-month-old male control, high-fat diet fed (HFD) or obese ob/ob mice by LC-MS(/MS) and quantified ~1,100 islet proteins (at least two peptides) with a false discovery rate <1%. Significant alterations in abundance were observed for ~350 proteins between groups. A majority of alterations were common to both models, and the changes of a subset of ~40 proteins and 12 proteins were verified by targeted quantification using selected reaction monitoring and Western blots, respectively. The insulin resistant islets in both groups exhibited reduced expression of proteins controlling energy metabolism, oxidative phosphorylation, hormone processing, and secretory pathways. Conversely, an increased expression of molecules involved in protein synthesis and folding suggested effects in endoplasmic reticulum stress response, cell survival, and proliferation in both insulin resistant models. In conclusion, we report a unique comparison of the islet proteome that is focused on the compensatory response in two insulin resistant rodent models that are not overtly diabetic. In conclusion, these data provide a valuable resource of candidate proteins to the scientific community to undertake further studies aimed at enhancing β-cell mass in patients with diabetes. The data are available via the MassIVE repository, with accession MSV000079093.

59 BASIC BIOLOGICAL SCIENCES↗

Resistive Switching Memory Performance of Two-Dimensional Polyimide Covalent Organic Framework Films

Two-dimensional polyimide covalent organic framework (2D PI-NT COF) films were constructed on indium tin oxide-coated glass substrates to fabricate two-terminal sandwiched resistive memory devices. The 2D PI-NT COF films condensated from the reaction between 4,4',4"-triaminotriphenylamine and naphthalene-1,4,5,8-tetracarboxylic dianhydride under solvothermal conditions demonstrated high crystallinity, good orientation preference, tunable thickness, and low surface roughness. The well-aligned electron-donor (triphenylamine unit) and -acceptor (naphthalene diimide unit) arrays rendered the 2D PI-NT COF films a promising candidate for electronic applications. The memory devices based on 2D PI-NT COF films exhibited a typical write-once-read-many-time resistive switching behavior under an operating voltage of +2.30 V on the positive scan and -2.64 V on the negative scan. A high ON/OFF current ratio (>10 6 for the positive scan and 10 4 -10 6 for the negative scan) and long-term retention time indicated the high fidelity, low error, and high stability of the resistive memory devices. The memory behavior was attributed to an electric field-induced intramolecular charge transfer in an ordered donor-acceptor system, which provided the effective charge-transfer channels for injected charge carriers. Furthermore, this work represents the first example that explores the resistive memory properties of 2D PI-COF films, shedding light on the potential application of 2D COFs as information storage media.

2D covalent organic framework film↗