SEARCH · Engineering Papers

Results for “process development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Silicon crystal growth in vacuum

The most developed process for silicon crystal growth is the Czochralski (CZ) method which was in production for over two decades. In an effort to reduce cost of single crystal silicon for photovoltaic applications, a directional solidification technique, Heat Exchanger Method (HEM), was adapted. Materials used in HEM and CZ furnaces are quite similar (heaters, crucibles, insulation, etc.). To eliminate the cost of high purity argon, it was intended to use vacuum operation in HEM. Two of the major problems encountered in vacuum processing of silicon are crucible decomposition and silicon carbide formation in the melt.

Khattak, C. P.↗

NASA NTRS1983

Small Gas Turbine Combustor Primary Zone Study

A development process is described which consists of design, fabrication, and preliminary test evaluations of three approaches to internal aerodynamic primary zone flow patterns: (1) conventional double vortex swirl stabilization; (2) reverse flow swirl stabilization; and (3) large single vortex flow system. Each concept incorporates special design features aimed at extending the performance capability of the small engine combustor. Since inherent geometry of these combustors result in small combustion zone height and high surface area to volume ratio, design features focus on internal aerodynamics, fuel placement, and advanced cooling. The combustors are evaluated on a full scale annular combustor rig. A correlation of the primary zone performance with the overall performance is accomplished using three intrusion type gas sampling probes located at the exit of the primary zone section. Empirical and numerical methods are used for designing and predicting the performance of the three combustor concepts and their subsequent modifications. The calibration of analytical procedures with actual test results permits an updating of the analytical design techniques applicable to small reverse flow annular combustors.

Sullivan, R. E.↗

NASA NTRS1983

Recommended approach to sofware development

A set of guideline for an organized, disciplined approach to software development, based on data collected and studied for 46 flight dynamics software development projects. Methods and practices for each phase of a software development life cycle that starts with requirements analysis and ends with acceptance testing are described; maintenance and operation is not addressed. For each defined life cycle phase, guidelines for the development process and its management, and the products produced and their reviews are presented.

Mcgarry, F. E.↗

NASA NTRS1983

Development of a flight test maneuver autopilot for a highly maneuverable aircraft

This paper details the development of a flight test maneuver autopilot for a highly maneuverable aircraft. This newly developed flight test technique is being applied at the Dryden Flight Research Facility of the NASA Ames Research Center. The flight test maneuver autopilot (FTMAP) is designed to increase the quantity and quality of the data obtained in flight test. The vehicle with which it is being used is the highly maneuverable aircraft technology (HiMAT) vehicle. This paper describes the HiMAT vehicle systems, maneuver requirements, FTMAP development process, and flight results.

Duke, E. L.↗

NASA NTRS1982

NASA space power system automation

Investigations were conducted with the objective to identify technology issues in automating space power systems, rank critical technology needs, and recommend technology objectives. It was found that automation can offer significant benefits to space power systems. Automation, or even autonomy, may become an absolute requirement for system implementation. Automation of large power systems will be achieved through evolution. It is pointed out that 'systems engineering' or more specifically, 'automation systems engineering' must be strongly emphasized and done early in the development process. System control can be centralized, distributed or a combination of the two. An important requirement for automation implementation is related to the availability of qualified hardware and software components.

Wagnon, F. W.↗

NASA NTRS1983

Three-dimensional algebraic grid generation

One of the major approaches to numerical grid generation is the explicit algebraic expression of a physical grid as a function of a uniform grid in a rectangular computational coordinate system. The algebraic methods are based on mathematical interpolation, and the primary advantages are speed and directness. The relation between interpolation and grid generation is described. For three-dimensional grid generation, transfinite interpolation using the coordinate control processes developed in the multisurface method and two-boundary technique are advocated. Grid singularities encountered in three dimensions are discussed, and the exploration of multiple overlapping grids is proposed. Some aspects of interactive algebraic grid computation in three dimensions are discussed.

Smith, R. E.↗

NASA NTRS1985

Making Cubic Silicon Carbide Semiconductors

Thin buffer layer of SiC minimizes effects of lattice mismatch. Approach consists of growing single-crystal layer of cubic SiC on single-crystal silicon (Si) wafer by chemical-vapor deposition (CVD). Process developed for production of large-area single-crystal wafers of cubic silicon carbide (SiC) for semiconductor devices; also used to make devices themselves. Applications include electronics for high temperature (up to 900 C) and electronics for very high frequencies.

Powell, J.↗

NASA NTRS1983

Testing and error analysis of a real-time controller

Inexpensive ways to organize and conduct system testing that were used on a real-time satellite network control system are outlined. This system contains roughly 50,000 lines of executable source code developed by a team of eight people. For a small investment of staff, the system was thoroughly tested, including automated regression testing, before field release. Detailed records were kept for fourteen months, during which several versions of the system were written. A separate testing group was not established, but testing itself was structured apart from the development process. The errors found during testing are examined by frequency per subsystem by size and complexity as well as by type. The code was released to the user in March, 1983. To date, only a few minor problems found with the system during its pre-service testing and user acceptance has been good.

Savolaine, C. G.↗

NASA NTRS1984

Payload crew training complex simulation engineer's handbook

The Simulation Engineer's Handbook is a guide for new engineers assigned to Experiment Simulation and a reference for engineers previously assigned. The experiment simulation process, development of experiment simulator requirements, development of experiment simulator hardware and software, and the verification of experiment simulators are discussed. The training required for experiment simulation is extensive and is only referenced in the handbook.

Shipman, D. L.↗

NASA NTRS1983

AFTI/F-16 DFCS development summary - A report to industry multimode control law design

The primary goal of the AFTI/F-16 program is to develop a reliable triplex digital multimode flight control system; this system is to be tailored to optimize fighter performance and capable of six-degree-of-freedom decoupled aircraft control. The multiple digital control law configurations arrived at through flight testing are presented. The changes in these designs from the results of flight tests establish that flight testing is an integral part of the development process. The flight test results are analyzed here from the standpoint of pilot comments and resulting control law design modifications.

Toles, R. D.↗

NASA NTRS1982

Non-mass-analyzed ion implantation equipment for high volume solar cell production

Equipment designed for junction formation in silicon solar cells is described. The equipment, designed for a production level of approximately one megawatt per year, consists of an ion implanter and annealer. Low cost is achieved by foregoing the use of mass analysis during the implantation, and by the use of a belt furnace for annealing. Results of process development, machine design and cost analysis are presented.

Armini, A. J.↗

NASA NTRS1983

Thermoregulation in cold- and noncold-acclimated rats cold exposed in hypergravic fields

The effect of hypergravity on thermoregulation processes is investigated experimentally in rats. Hooded male Long-Evans rats were kept for 6 weeks at 5 or 23 C (cold-acclimated and noncold-acclimated groups, CA and NCA) prior to testing. One test protocol comprised sequential 1-h exposures to 23 C at 1 G, 23 C at 3 G (in a 2.1-m radius centrifuge; -Gx), 8 C at 3 G, 8 C at 1 G, and finally 23 C at 1 G, with continuous measurement of the oxygen consumption. In a second protocol, restrained rats were exposed to 23 C at 1 G, 23 C at 3 G, and 10 C at 3 G, and core temperature changes were monitored. The results are presented in graphs and a table. Oxygen consumption doubled in both CA and NCA rats on exposure to cold at 1 G, but at 3 G NCA consumption decreased while CA consumption remained high. The CA rats were also more able to maintain core temperature at 3 G than the NCA rats. These differences are attributed to the nonshivering thermogenic processes developed in CA rats, which appear to be unaffected by hypergravity.

Horowitz, J. M.↗

NASA NTRS1985

Analyzing Microchips With Dark-Field Negative Photomicrography

Inverse development process yields fine details. Photomicrographic technique produces images of integrated-circuit chips. Technique based on dark-field illumination: (chip lit with bright central spot of light and photographed by light scattered or diffracted from spot. Reveals more about microstructure patterns related to photoresist masking than more conventional bright-field method.

Suszko, S. F.↗

NASA NTRS1986

Economical Fabrication of Large Parabolic Mirrors

Long-focal-length parabolic mirrors fabricated economically by rotational casting. Technique applies to very large mirrors and incorporates new foam/fiberglass techniques ideal for producing rigid, lightweight mirrors. Process developed to produce mirrors that concentrate Sunlight for solarpumped laser.

Schneider, R. T.↗

NASA NTRS1984

Proceedings of the 24th Project Integration Meeting

Progress made by the Flat-Plate Solar Array Project is described. Reports on silicon sheet growth and characterization, silicon material, process development, high-efficiency cells, environmental isolation, engineering sciences, and reliability physics are presented along with copies of visual presentations made at the 24th Project Integration Meeting.

Tustin, D.↗

NASA NTRS1984

The future of crystalline silicon technology in the US Department of Energy program

Two basic findings were presented in the outlined report. The first is that silicon has a very high potential efficiency, demonstrated improvement in reliability and a significant potential for cost reductions. The second is that the photovoltaic technology development process is highly uncertain, but crystalline silicon technology has a substantial knowledge base to draw from, improving its chances of success. Several issues to be addressed are outlined.

Scolaro, A. F.↗

NASA NTRS1984

A methodology for collecting valid software engineering data

An effective data collection method for evaluating software development methodologies and for studying the software development process is described. The method uses goal-directed data collection to evaluate methodologies with respect to the claims made for them. Such claims are used as a basis for defining the goals of the data collection, establishing a list of questions of interest to be answered by data analysis, defining a set of data categorization schemes, and designing a data collection form. Feasibility of the data collection methodology was demonstrated by applying it to five different projects in two different environments (other NRL Reports). The application showed that the methodology was both feasible and useful.

Basili, V. R.↗

NASA NTRS1986

Process Produces Low-Secondary-Electron-Emission Surfaces

Textured carbon layer applied to copper by sputtering. Carbon surface characterized by dense, random array of needle-like spires or peaks that extend perpendicularly from local copper surface. Spires approximately 7 micrometers in height and spaced approximately 3 micrometers apart, on average. Copper substrate essentially completely covered by carbon layer, is tenacious and not damaged by vibration loadings representative of multistage depressed collector (MDC) applications. Process developed primarily to provide extremely low-secondary-electron-emission surface for copper for use as highefficiency electrodes in MDC's for microwave amplifier traveling-wave tubes (TWT's). Tubes widely used in space communications, aircraft, and terrestrial applications.

Curren, A. N.↗