Synthesis and Electronic Properties of Diketopyrrolopyrrole-Based Polymers with and without Ring-Fusion
Not Available
36 MATERIALS SCIENCE↗
SEARCH · Engineering Papers
Results for “polymer science”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Polymer thin films as universal substrates for extreme ultraviolet absorption spectroscopy of molecular transition metal complexes
Polystyrene and polyvinyl chloride thin films are explored as sample supports for extreme ultraviolet (XUV) spectroscopy of molecular transition metal complexes. Thin polymer films prepared by slip-coating are flat and smooth, and transmit much more XUV light than silicon nitride windows. Analytes can be directly cast onto the polymer surface or co-deposited within it. The M-edge XANES spectra (40–90 eV) of eight archetypal transition metal complexes (M = Mn, Fe, Co, Ni) are presented to demonstrate the versatility of this method. The films are suitable for pump/probe transient absorption spectroscopy, as shown by the excited-state spectra of Fe(bpy) 3 2+ in two different polymer supports.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Morphology of poly-3-hexyl-thiophene blends with styrene–isoprene–styrene block-copolymer elastomers from X-ray and neutron scattering
The nano- and micron scale morphology of poly(3-hexylthiophene) (P3HT) and polystyrene-block-polyisoprene-block-polystyrene (PS–PI–PS) elastomeric blends is investigated through the use of ultra-small and small angle X-ray and neutron scattering (USAXS, SAXS, SANS). It is demonstrated that loading P3HT into elastomer matrices is possible with little distortion of the elastomeric structure up to a loading of ~5 wt%. Increased loadings of conjugated polymer is found to significantly distort the matrix structure. Changes in processing conditions are also found to affect the blend morphology with especially strong dependence on processing temperature. Processing temperatures above the glass transition temperature (T g ) of polystyrene and the melting temperature (T m ) of the conjugated polymer additive (P3HT) creates significantly more organized mesophase domains. P3HT blends with PS–PI–PS can also be flow-aligned through processing, which results in an anisotropic structure that could be useful for the generation of anisotropic properties (e.g. conductivity). Moreover, the extent of flow alignment is significantly affected by the P3HT loading in the PS–PI–PS matrix. The work adds insight to the morphological understanding of a complex P3HT and PS–PI–PS polymer blend as conjugated polymer is added to the system. Here, we also provide studies isolating the effect of processing changes aiding in the understanding of the structural changes in this elastomeric conjugated polymer blend.
36 MATERIALS SCIENCE↗
Ion-Conducting Thermoresponsive Films Based on Polymer-Grafted Cellulose Nanocrystals
Mechanically robust, thermo-responsive, ion-conducting nanocomposite films are prepared from poly(2-phenylethyl methacrylate) grafted cellulose nanocrystals (MxG-CNC-g-PPMA). One-component nanocomposite films of the polymer grafted nanoparticle (PGN) MxG-CNC-g-PPMA are imbibed with 30 wt% imidazolium-based ionic liquid, to produce flexible ion-conducting films. These films with 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (MxG-CNC-g-PPMA/[H]) not only displays remarkable improvements in toughness (>25 times) and tensile strength (>70 times) relative to the corresponding nanocomposites consisting of the ionic liquid imbibed in the two component CNC/PPMA nanocomposite, but also shows higher ionic conductivity than the corresponding neat PPMA with the same wt.% of ionic liquid. Notably, the one-component film containing 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (MxG-CNC-g-PPMA/[E]) exhibits temperature responsive ionic conduction. The ionic conductivity decreases at around 60°C as a consequence of the lower critical solution temperature (LCST) phase transition of the grafted polymer in the ionic liquid, which leads to phase separation. Moreover, holding the MxG-CNC-g-PPMA/[E] film at room temperature for 24 hours returns the film to its original homogenous state. These materials exhibit properties relevant to thermal cutoff safety devices (e.g., thermal fuse) where a reduction in conductivity above a critical temperature is needed.
36 MATERIALS SCIENCE↗
Degradable Biocomposite Thermoplastic Polyurethanes
In this project, the team developed tough and degradable biocomposite thermoplastic polyurethanes (TPUs) by incorporating bacterial spores into TPUs as a biofunctional living filler. The team screened various bacteria and selected the Bacillus subtilis ATCC 6633 strain as the final candidate, primarily due to its genomic availability, sporulation ability and TPU assimilation activity. The heat-shock tolerance of ATCC 6633 spores was further improved through evolutionary engineering via Adaptive Laboratory Evolution (ALE), demonstrating a 17.7-fold enhanced germination efficiency post heat-shock treatment compared to the wild-type strain (WT). The team fabricated biocomposite TPUs by incorporating lyophilized powder of heat-shock tolerized (HST) spores during the hot melt extrusion (HME) of TPU at 135 °C. The baseline TPU used in this project is a commercially available soft-grade TPU (BCF45) manufactured by BASF. Colony forming unit (CFU) assays quantified that WT and HST spores in the TPU matrix retained approximately 20% and 100% survivability, respectively, after HME. Tensile testing demonstrated that the spores behaved as a polymer-reinforcing filler, positively affecting the overall tensile properties of the biocomposite TPU. For example, biocomposite TPU with WT and HST spores (BC TPU WT and BC TPU HST , respectively) exhibited up to 25% and 37% improved toughness, respectively, compared to TPU without spores. BC TPU HST showed remarkably improved disintegration in autoclaved compost (92% mass loss in 5 months), which simulated a microbially poor environment for TPU degradation. When compared to TPU without spores (44% mass loss in 5 months) the acceleration of degradation is marked. Respirometry confirmed that 72% of BC TPU HST was biomineralized into CO2 within 6 months, indicating that spores in the biocomposite TPU were germinated by utilizing nutrients in the autoclaved compost, facilitating TPU degradation at the end of the material's life. The team demonstrated the scale-up of biocomposite TPU fabrication using continuous extrusion and injection molding techniques. Processing conditions optimized in a lab-scale microcompounder were successfully transferred to a continuous extruder with a 30-fold increased throughput. Biocomposite TPUs prepared using these industry-relevant processes showed comparable toughness improvements to samples prepared in the lab-scale extruder. Excitingly, following compounding in the pilot-extruder the composite material could be injection molded, while retaining high spore viability and similar toughness improvements. The team also found that spores in biocomposite TPU served as antioxidants, preventing toughness decay during the recycled extrusion of BC TPU HST . Long-term storage tests over one year showed that the addition of spores had no negative effect on the longevity of the TPU. Furthermore, the team demonstrated the fabrication of spore-bearing biocomposite polymers with other polyesters such as PBAT, PLA, and PCL. We obtained promising preliminary data that showed overall toughness improvements for all polymers with spore addition. Finally, life cycle assessment (LCA) and techno-economic analysis (TEA) were carried out, which indicated minimal additional cost of fabrication. Overall, a tough and degradable biocomposite thermoplastic was successfully developed through this project, with all tasks completed successfully, achieving >100% of the objectives.
36 MATERIALS SCIENCE↗
Tunable PA6 Polymer System for Thermoplastic Reinforced Body Panels
Project Goal: Overall, a redesigned polyamide system will combine the ductility and processing of a PA6 matrix, the strength and modulus of CF, and the facile recyclability of esters. Approach: PEA can be synthesized under conventional, industrially relevant pathways. Material properties and processing will be analyzed and compared to commercial PA6 material. Results: Polycondensation, traditional for polyesters, was successful in synthesized a PEA. PEA exhibited fast crystallization and bimodal melting behavior suggesting beneficial crystallization kinetics. PEA exhibit reduced melting temperatures owed to the incorporation of ester units in the polymer structure.
42 ENGINEERING↗
Synthesis and Characterization of Self-Assembled Metal-Organic Framework Monolayers using Polymer-coated Particles
Not provided.
Science & Technology - Other Topics↗
Biologically inspired robots as artificial inspectors - science fiction engineering reality
Explore the source record for details and available documents.
electroactive polymer artificial muscles robotics ↗
Design of materials with supramolecular polymers
One hundred years ago Hermann Staudinger was strongly criticized by his scientific peers for his macromolecular hypothesis, but today it is hard to imagine a world without polymers. His hypothesis described polymers as macromolecules composed of large numbers of structural units connected by covalent bonds. In the 1990s the concept of supramolecular polymers emerged in the scientific literature as discrete entities of large molar mass comparable to that of classical polymers but built through non-covalent bonds among monomers. Supramolecular polymers exist in biological systems, and potentially blend the physical properties of covalent polymers with unique features such as high degrees of internal order within the polymeric structure, defined shapes, and novel dynamics. This trend article provides a summary of seminal contributions in supramolecular polymerization and provides recent examples from the Stupp laboratory to demonstrate the potential applications of an exciting class of materials composed fully or partially of supramolecular polymers. Finally, in closing, we provide our perspective on future opportunities provided by this field at the onset of a second century of polymers. It is our objective here to demonstrate that this second century could be as prosperous, if not more so, than the preceding one.
36 MATERIALS SCIENCE↗
Development of Additive Manufacturing for Ceramic Matrix Composite Vanes
This report discusses the development of additive manufacturing for polymer-derived ceramic materials to create novel cooled gas turbine airfoils made from ceramics. Gas turbine engines have extremely high temperatures in the hot section of the engine that exceed the melting point of nickel superalloy materials that the engine is made from. Advanced cooling technologies have been developed over decades for metallic parts. Ceramic materials have higher temperature capabilities than superalloys, but are difficult to shape in the complex designs used in modern turbines. Several thrusts were investigated during the project, including development of higher material strength resins, improvement of ultraviolet (UV) photopolymerization and post-processing techniques to increase survivability of ceramic parts, thermomechanical modeling of novel ceramic airfoil designs for higher cooling effectiveness, and experimental validation of the modeling and manufacturing in a turbine vane test facility at nondimensional conditions that are relevant to modern gas turbines. Some major findings of the work include a significant increase in ceramic survivability during pyrolysis (a high temperature process that converts the organic material to a ceramic) by adjusting the composition ratios of the resins, as well as a tolulene soak after printing to remove unreacted polymer material. Thermomechanical optimization of the internal cooling structure indicated that a high density pin fin array would enable an 80% increase in overall cooling effectiveness relative to a baseline geometry, which was later verified during experimental testing in a high speed linear cascade. Ceramic vanes were tested at Mach numbers of up to 0.9 which is relevant to modern gas turbines. High temperature capability of the ceramic vanes was not tested in this work.
36 MATERIALS SCIENCE↗
Fracture of PC and PMMA cylinders in the Taylor tests
The present paper analyzes failure observed in polymer rods collided with a steel anvil under the Taylor cylinder impact experiments. The experimental and numerical analysis demonstrates that association of the failure patterns with the loading mode depends on the rod material. Two materials are considered in the paper, specifically, polymethylmethacrylate (PMMA) and polycarbonate (PC). Damage in PMMA rods at the Taylor tests is shown to be dominated by the shear load resulting in plastic deformation. In contrast, the major mechanism of damage in PC rods is governed by omni-directional (pressure) mode of load. Analysis of the damage in sections of the rods associated with the glass transition is also addressed in the present theoretical study. Failure in these polymers follows the traditional fracture wave mechanism for brittle glass-type materials due to load in the corresponding mode. Numerical analysis employs a two-phase model with improved inter-phase thermal balance accounting for the inter-phase mass, momentum, and heat exchanges during the glass phase transition, while damage being accumulated in time. In conclusion, the simulation results demonstrate a good correlation with the experimental results.
36 MATERIALS SCIENCE↗
High-Performance, Hybrid Polymer Membrane for Carbon Dioxide Separation from Ambient Air
The Department of Energy (DOE) seeks to develop carbon capture materials specifically tailored for Direct Air Capture (DAC) processes. Related to this, they require recipients to develop novel DAC materials such as: solvents, membranes, or sorbents that demonstrate high affinities or capacities for carbon dioxide (CO2) at concentrations typically available in air and at near ambient conditions. Toward this, InnoSense LLC (ISL) is developing High-Performance, Hybrid Polymer Membranes (HypoMemTM) for Carbon Dioxide Separation from Ambient Air. HypoMem consists of two major layers. The first layer is the active layer which contains the active ingredients that help to separate CO2 from ambient air. The second is the support layer that provides good mechanical support to have a free-standing membrane without interfering with the properties of the active layer.
20 FOSSIL-FUELED POWER PLANTS↗
Compression Analysis of Materials via in situ X-ray Computed Tomography
X-ray computed tomography (X-ray CT) is an analytical technique used in materials science to non– destructively characterize features in a variety of materials like polymers, metals, composites, and explosives. The non-destructive imaging allows for the analysis of features (voids and cracks), which give a fundamental understanding of material characteristics.This is more effective when combinedwith a load cell to expose the material to realworld stimuli to understand material characteristics and morphological behavior in situ. This study focused on using in situ X-ray CT to understand the material characteristics and morphological changes of sugar prills and a lattice under a compressive load. Sugar prills are used as a surrogate to analyze explosives in a safer and less expensiveway. The sugar prills were found to be brittle and shattered when compressed via the CT renderings and the stress/strain information. The lattices are used as both the basis and ground truth comparison for the development of models to predict the morphological and material characteristic changes that occur as a result of loading. The lattice was found to have weak regions due to low polymer interlayer fusion in these regions during the printing process. It was also found that under the initial compression the lattice demonstrated elastic behavior as its cellular structure was intact until the cellular structure started to collapse causing yielding in the lattice. Additionally, the analysis of the sugar prills and lattice demonstrate the information that can be gleaned from in situ X-ray CT experiments that would be lost in traditional pre- and post-mortem X-rayCT analysis.
36 MATERIALS SCIENCE↗
Autonomous platform for solution processing of electronic polymers
The manipulation of electronic polymers’ solid-state properties through processing is crucial in electronics and energy research. Yet, efficiently processing electronic polymer solutions into thin films with specific properties remains a formidable challenge. We introduce Polybot, an artificial intelligence (AI) driven automated material laboratory designed to autonomously explore processing pathways for achieving high-conductivity, low-defect electronic polymers films. Leveraging importance-guided Bayesian optimization, Polybot efficiently navigates a complex 7-dimensional processing space. In particular, the automated workflow and algorithms effectively explore the search space, mitigate biases, employ statistical methods to ensure data repeatability, and concurrently optimize multiple objectives with precision. The experimental campaign yields scale-up fabrication recipes, producing transparent conductive thin films with averaged conductivity exceeding 4500 S/cm. Feature importance analysis and morphological characterizations reveal key design factors. This work signifies a significant step towards transforming the manufacturing of electronic polymers, highlighting the potential of AI-driven automation in material science.
Wang, Chengshi [Argonne National Laboratory (ANL),↗
Spectroscopic comparison of effects of electron radiation on mechanical properties of two polyimides
The differences in the radiation durabilities of two polyimide materials, Du Pont Kapton and General Electric Ultem, are compared. An explanation of the basic mechanisms which occur during exposure to electron radiation from analyses of infrared (IR) and electron paramagnetic resonance (EPR) spectroscopic data for each material is provided. The molecular model for Kapton was, in part, established from earlier modeling for Ultem (pp. 1293-1298 of IEEE Transactions on Nuclear Science, December 1984). Techniques for understanding the durability of one complex polymer based on the understanding of a different and equally complex polymer are demonstrated. The spectroscopic data showed that the primary radiation-generated change in the tensile properties of Ultem (a large reduction in tensile elongation) was due to crosslinking, which followed the capture by phenyl radicals of hydrogen atoms removed from gem-dimethyl groups. In contrast, the tensile properties of Kapton remained unchanged because radical-radical recombination, a self-mending process, took place.
Long, Edward R., Jr.↗
Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks
Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young’s modulus and ~100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. Here, the interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.
36 MATERIALS SCIENCE↗
Topological Effects Near Order–Disorder Transitions in Symmetric Diblock Copolymer Melts
The effects of polymer chain topology on the order–disorder transition of symmetric AB diblock copolymer melts are studied using coarse-grained molecular dynamics simulations. Specifically, we compared chain conformations near the lamellar-disordered transition in melts of symmetric (i.e., 50–50) AB diblock copolymers of linear chains, rings, and trefoil knots at the same chain lengths. The order (lamellar)–disorder transition temperature and the domain sizes both shifted to lower values with the introduction of topological constraints, leading to the following sequence: linear chains > rings > trefoil knots. Furthermore, investigation of the polymer chain conformations in terms of their radii of gyration, their writhe values (a measure for the degree of intertwining of a chain around itself), and their Jones polynomials (a method to measure entanglement of curves) showed that linear chains and rings remained stretched, while knots were stretched and tightened in disordered melts close to the lamellar-disorder transition. This work highlights chain topology as an important factor in affecting microphase separation in block copolymers.
36 MATERIALS SCIENCE↗
Biorenewable and circular polydiketoenamine plastics
Amid growing concerns over the human health and environmental impacts of plastic waste, the most promising solution would be to build a circular plastics economy where sustainability considerations dictate the full life cycle of plastics use including replacing petrochemicals with biorenewables. Here we show that by incorporating the polyketide triacetic acid lactone (TAL) in polydiketoenamines (PDK) we increase the working temperature of these circular plastics, opening the door wider to applications where circularity is urgently needed. By varying the number of carbons of TAL-derived monomers, both polymer properties and recycling efciency are afected. Simply using glucose as the main carbon source, we engineered a process for producing bioTAL under fed-batch fermentation. Furthermore, a systems analysis of this bioprocess under diferent scenarios quantifes the environmental and economic benefts of PDK plastics and the risks when implemented at an industrial scale, providing opportunities in biorenewable circularity.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗