Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

All-optical seeding of a light-induced phase transition with correlated disorder

Ultrafast manipulation of vibrational coherence is an emergent route to control the structure of solids. However, this strategy can only induce long-range correlations and cannot modify atomic structure locally, which is required in many technologically-relevant phase transitions. Here, we demonstrate that ultrafast lasers can generate incoherent structural fluctuations which are more efficient for material control than coherent vibrations, extending optical control to a wider range of materials. We observe that local, non-equilibrium lattice distortions generated by a weak laser pulse reduce the energy barrier to switch between insulating and metallic states in vanadium dioxide by 6%. In conclusion, seeding inhomogeneous structural-fluctuations presents an alternative, more energy efficient, route for controlling materials that may be applicable to all solids, including those used in data and energy storage devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modulating Oxide‐Based Quantum Materials by Ion Implantation

Ion implantation has emerged as a powerful tool for manipulating and investigating oxide quantum materials, where strong electron correlations give rise to exotic phases and functionalities. This Review examines how controlled ion bombardment enables targeted modulation of structural, electronic, and magnetic properties in complex oxides. Recent advances in ion beam techniques is analyzed that provide unprecedented control over defect profiles, from point defects to extended damage cascades. In application, ion irradiation has demonstrated the ability to tune quantum phenomena including metal‐insulator transitions, magnetism, and superconductivity through selective doping, defect creation, and lattice strain. The ability to write quantum states with nanoscale precision using focused ion beams is opening new paths for quantum device fabrication. Challenges in understanding radiation damage mechanisms in strongly correlated systems is discussed, and identify opportunities for designing quantum functionality through defect‐engineering approaches. The technique's demonstrated capability to write quantum states with nanoscale precision, combined with its compatibility with existing semiconductor processing infrastructure, suggests a clear pathway for translating fundamental discoveries in quantum materials into practical technological applications.

defect engineering↗
DOE OSTI2023

Zr‐Porphyrin Metal–Organic Framework as nanoreactor for boosting the formation of hydrogen clathrates

Abstract We report the first experimental evidence for rapid formation of hydrogen clathrates under mild pressure and temperature conditions within the cavities of a zirconium‐metalloporphyrin framework, specifically PCN‐222. PCN‐222 has been selected for its 1D mesoporous channels, high water‐stability, and proper hydrophilic behavior. Firstly, we optimize a microwave (MW)‐assisted method for the synthesis of nanosized PCN‐222 particles with precise structure control (exceptional homogeneity in morphology and crystalline phase purity), taking advantage of MW in terms of rapid/homogeneous heating, time and energy savings, as well as potential scalability of the synthetic method. Second, we explore the relevance of the large mesoporous 1D open channels within the PCN‐222 to promote the nucleation and growth of confined hydrogen clathrates. Experimental results show that PCN‐222 drives the nucleation process at a lower pressure than the bulk system (1.35 kbar vs 2 kbar), with fast kinetics (minutes), using pure water, and with a nearly complete water‐to‐hydrate conversion. Unfortunately, PCN‐222 cannot withstand these high pressures, which lead to a significant alteration of the mesoporous structure while the microporous network remains mainly unchanged.

Carrillo‐Carrión, Carolina↗
DOE OSTI2024

Zr‐Porphyrin Metal–Organic Framework as nanoreactor for boosting the formation of hydrogen clathrates

Abstract We report the first experimental evidence for rapid formation of hydrogen clathrates under mild pressure and temperature conditions within the cavities of a zirconium‐metalloporphyrin framework, specifically PCN‐222. PCN‐222 has been selected for its 1D mesoporous channels, high water‐stability, and proper hydrophilic behavior. Firstly, we optimize a microwave (MW)‐assisted method for the synthesis of nanosized PCN‐222 particles with precise structure control (exceptional homogeneity in morphology and crystalline phase purity), taking advantage of MW in terms of rapid/homogeneous heating, time and energy savings, as well as potential scalability of the synthetic method. Second, we explore the relevance of the large mesoporous 1D open channels within the PCN‐222 to promote the nucleation and growth of confined hydrogen clathrates. Experimental results show that PCN‐222 drives the nucleation process at a lower pressure than the bulk system (1.35 kbar vs 2 kbar), with fast kinetics (minutes), using pure water, and with a nearly complete water‐to‐hydrate conversion. Unfortunately, PCN‐222 cannot withstand these high pressures, which lead to a significant alteration of the mesoporous structure while the microporous network remains mainly unchanged.

Carrillo‐Carrión, Carolina↗
DOE OSTI2020

Boosting the sodium storage behaviors of carbon materials in ether-based electrolyte through the artificial manipulation of microstructure

The porous carbon blacks rationally designed by a facile yet efficient NH 3 thermal etching route have been investigated as anode materials in an ether-based electrolyte for sodium-ion batteries. The as-synthesized CBN35 carbon black with a 35% weight loss after NH3 thermal etching exhibited a large specific charge capacity of 352 mAh g -1 at 50 mA g -1 and a superior rate capability of 101 mAh g -1 at 16000 mA g -1 , due to its highest microporosity, an appropriate surface area, a desirable microstructure, and a promising hybrid intercalation mechanism. Impressively, even cycled at 1600 mA g -1 over 3200 cycles, an outstanding reversible capacity of 103 mAh g -1 with a negligible 0.0162% capacity loss per cycle can still be achieved. Based on the multimodal characterizations including the structural probes of phase evolution for carbon materials, the electrochemical techniques, and the surface-sensitive XAS measurements, the exceptional electrochemical properties should stem from several merits of modified carbon black system. While the particular microporous structure provides relatively more accessible sodium storage sites, a novel hybrid intercalation mechanism in ether-based electrolyte would incorporate the sodium ion insertion into the disordered structure with the solvated sodium ion species co-intercalation into the graphitic phase. In addition to the diffusion-controlled redox reactions, the noticeable surface-induced pseudocapacitive reactions also significantly contribute to the charge storage upon sodiation and guarantee the rapid migrations of sodium ions/solvated compounds. In conclusion, this system further features a controlled emergence of a robust but thin solid electrolyte interphase layer, which could suppress the side reactions of active electrode with reactive electrolyte, maintain the fragile porous structure upon cycling, and facilitate the migrations of sodium ions and solvated sodium ion compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Excitonic Mott insulator in a Bose-Fermi-Hubbard system of moiré WS 2 /WSe 2 heterobilayer

Understanding the Hubbard model is crucial for investigating various quantum many-body states and its fermionic and bosonic versions have been largely realized separately. Recently, transition metal dichalcogenides heterobilayers have emerged as a promising platform for simulating the rich physics of the Hubbard model. In this work, we explore the interplay between fermionic and bosonic populations, using a WS 2 /WSe 2 heterobilayer device that hosts this hybrid particle density. We independently tune the fermionic and bosonic populations by electronic doping and optical injection of electron-hole pairs, respectively. This enables us to form strongly interacting excitons that are manifested in a large energy gap in the photoluminescence spectrum. The incompressibility of excitons is further corroborated by observing a suppression of exciton diffusion with increasing pump intensity, as opposed to the expected behavior of a weakly interacting gas of bosons, suggesting the formation of a bosonic Mott insulator. We explain our observations using a two-band model including phase space filling. Our system provides a controllable approach to the exploration of quantum many-body effects in the generalized Bose-Fermi-Hubbard model.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enabling elliptically polarized high harmonic generation with short cross polarized laser pulses

Abstract Enabling elliptically polarized high-order harmonics overcomes a historical limitation in the generation of this highly nonlinear process in atomic, molecular and optical physics with applications in other branches. Here, we shed new light on a controversy between experimental observations and theoretical predictions on the possibility to generate harmonics with large ellipticity using two bichromatic laser pulses which are linearly polarized in orthogonal directions. Results of numerical calculations confirm the previous experimental data that in short laser pulses even harmonics with large ellipticity can be obtained for the interaction of such cross-polarized laser pulses with atoms initially in a s - or p -state, while odd harmonics have low ellipticity. The amount of the ellipticity can be controlled via the relative carrier-envelope phase of the pulses, their intensity ratio and the duration of the pulses.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Ultrafast enhancement of electron-phonon coupling via dynamic quantum well states

Abstract The density of states at the Fermi surface controls many material properties by influencing the low-energy interactions of conductive electrons. Typically, external tuning knobs generate only small perturbations to the density of states in crystals, since their band structure depends strongly on the lattice potential. In contrast, quantum well states are contingent on a localized potential extrinsic to the crystal lattice and can be easily modified leading to changes in the density of states at the Fermi level. Here, we are able to control the quantum well potential on the surface of Bi 2 Se 3 with light, driving a density of states singularity below E F at ultrafast timescales, thereby triggering a reversible Lifshitz transition. We reveal a substantial ultrafast enhancement of the electron-phonon coupling with repercussions on the relaxation dynamics in the system. We argue that the relaxation dynamics are governed largely by the interplay of the dynamic density of states of the quantum wells with c -axis scattering from the $${A}_{{{{{{{{\rm{1g}}}}}}}}}^{2}$$ A 1g 2 optical phonon mode. These results demonstrate a powerful way to enhance electron-boson interaction on ultrafast timescales providing new avenues for controlling material properties and driving novel quantum phases of matter.

Ciocys, Samuel T.↗
DOE OSTI2021

Volumetric recombination in EMC3-EIRENE: Implementation and first application to the pre-fusion power operation phase in ITER

An upgrade to the 3D plasma boundary model EMC3-EIRENE for detached divertor plasmas is introduced and evaluated. Stabilization of the iterative approximation of a self-consistent plasma–neutral gas solution is required at low divertor plasma temperatures, and this has been achieved by linearization of the energy loss term associated with the electron–neutral gas interaction. An implicit method for volumetric recombination has been implemented, which improves agreement with SOLPS-ITER results for the pre-fusion power operation phase in ITER. Resonant magnetic perturbations for control of edge localized modes are found to result in a partially detached divertor plasma with a significantly broader reduction of particle loads in the traditional strike zone, which is attributed to volumetric recombination. The additional non-axisymmetric far scrape-off layer strike points, on the other hand, remain attached at relatively high temperature so that volumetric recombination is not effective there.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Electrical and structural properties of binary Ga–Sb phase change memory alloys

Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.

Ume, Rubab (ORCID:0000000324766900)↗
DOE OSTI2021

Enhancing ion transport in charged block copolymers by stabilizing low symmetry morphology: Electrostatic control of interfaces

Recently, the interest in charged polymers has been rapidly growing due to their uses in energy storage and transfer devices. Yet, polymer electrolyte-based devices are not on the immediate horizon because of the low ionic conductivity. In the present study, we developed a methodology to enhance the ionic conductivity of charged block copolymers comprising ionic liquids through the electrostatic control of the interfacial layers. Unprecedented reentrant phase transitions between lamellar and A15 structures were seen, which cannot be explained by well-established thermodynamic factors. X-ray scattering experiments and molecular dynamics simulations revealed the formation of fascinating, thin ionic shell layers composed of ionic complexes. The ionic liquid cations of these complexes predominantly presented near the micellar interfaces if they had strong binding affinity with the charged polymer chains. Therefore, the interfacial properties and concentration fluctuations of the A15 structures were crucially dependent on the type of tethered acid groups in the polymers. Overall, the stabilization energies of the A15 structures were greater when enriched, attractive electrostatic interactions were present at the micellar interfaces. Contrary to the conventional wisdom that block copolymer interfaces act as “dead zone” to significantly deteriorate ion transport, this study establishes a prospective avenue for advanced polymer electrolyte having tailor-made interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Stochastic transition in synchronized spiking nanooscillators

This work reports that synchronization of Mott material-based nanoscale coupled spiking oscillators can be drastically different from that in conventional harmonic oscillators. We investigated the synchronization of spiking nanooscillators mediated by thermal interactions due to the close physical proximity of the devices. Controlling the driving voltage enables in-phase 1:1 and 2:1 integer synchronization modes between neighboring oscillators. Transition between these two integer modes occurs through an unusual stochastic synchronization regime instead of the loss of spiking coherence. In the stochastic synchronization regime, random length spiking sequences belonging to the 1:1 and 2:1 integer modes are intermixed. The occurrence of this stochasticity is an important factor that must be taken into account in the design of large-scale spiking networks for hardware-level implementation of novel computational paradigms such as neuromorphic and stochastic computing.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Investigating parameter trainability in the SNAP-displacement protocol of a qudit system

Here, in this study, we explore the universality of Selective Number-dependent Arbitrary Phase (SNAP) and Displacement gates for quantum control in qudit-based systems. However, optimizing the parameters of these gates poses a challenging task. Our main focus is to investigate the sensitivity of training any of the SNAP parameters in the SNAP-Displacement protocol. We analyze conditions that could potentially lead to the Barren Plateau problem in a qudit system and draw comparisons with multi-qubit systems. The parameterized ansatz we consider consists of blocks, where each block is composed of hardware operations, namely SNAP and Displacement gates [Fösel et al 2020 Efficient cavity control with snap gates arXiv:2004.14256]. Applying Variational Quantum algorithm (VQA) with observable and gate cost functions, we utilize techniques similar to those in [McClean et al 2018 Barren plateaus in quantum neural network training landscapes Nat. Commun.9 1–6] and [Cerezo et al 2021 Cost function dependent barren plateaus in shallow parametrized quantum circuits. Nat. Commun.12 1–12] along with the concept of t − design. Through this analysis, we make the following key observations: (a) The trainability of a SNAP-parameter does not exhibit a preference for any particular direction within our cost function landscape, (b) By leveraging the first and second moments properties of Haar measures, we establish new lemmas concerning the expectation of certain polynomial functions, and (c) utilizing these new lemmas, we identify a general condition that indicates an expected trainability advantage in a qudit system when compared to multi-qubit systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Characterization and QC practice of 16-channel ADC ASIC at cryogenic temperature for Liquid Argon TPC front-end readout electronics system in DUNE experiment

ColdADC is a low-noise 16-channel analog-to-digital converter ASIC designed for cold readout electronics of Liquid Argon Time Projection Chambers (LArTPCs) in the Deep Underground Neutrino Experiment (DUNE). ColdADC was specifically designed for operation at cryogenic temperatures (77 K–89 K). Cold electronics is considered to be an enabling technology for liquid argon detectors in neutrino experiments. The main function of the chip is to digitize signals from the 16-channel charge-sensitive amplifier designed at BNL (LArASIC) and send digitized signals to the data aggregator and serializer chip (COLDATA). ColdADC operates with a resolution of 12 bits and a sampling rate of 2 MS/s per channel. A complete characterization of prototype chips was conducted at cryogenic temperature, involving power consumption, noise and linearity performance. In the first DUNE Far-Detector module, 384000 data channels will be read out, corresponding to 24000 ColdADC chips. Therefore, systematic testing of ColdADC chips at cryogenic temperature is vital for the quality and reliability of DUNE Single-Phase modules. We have developed a Quality Control (QC) test stand that includes ColdADC evaluation and characterization at cryogenic temperature. The QC procedure was applied to a first batch of 33 chips, corresponding to 528 data channels. The obtained results meet all the required DUNE specifications for ColdADC. Moreover, the testing outcome allowed us to identify possibilities of performance optimization that are currently being addressed in the design of the next version of the chip. The Quality Control procedure is proved to be successful and will be a reference design for future large-batch production testing of final ColdADC ASICs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Event driven readout architecture with non-priority arbitration for radiation detectors

A novel event driven readout architecture, EDWARD (Event Driven with Access and 8 Reset Decoder) architecture, for highly granular pixel detectors is presented. It incorporates, inter alia, an asynchronous arbitration tree based on Seitz' arbiters, removing the need for an imposed prioritization scheme. It also provides protection against glitches during readout. The system allows not only reading pixel activities, but also retrieving additional data, both analog and digital, from the pixels. A novel in-channel logic allows the entire readout process to be split into consecutive phases for additional flexibility. All operations are controlled by only one edge of the clock signal, seen as an acknowledge token, so there is no dead time between readouts.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Smart Inverters for Seamless Reconnection of Isolated Residential Microgrids to Utility Grid

This paper proposes an approach to achieve seamless reconnection of isolated residential microgrids to utility grid. Any abnormal condition on the grid side results in isolating the residential microgrid from utility grid, and giving the full responsibility of supplying household loads to local distributed generation (DG) units. However, after resolving the abnormal condition on the grid side, the residential microgrid needs to seamlessly reconnect to the main grid. To this end, a seamless transition algorithm is presented which monitors the system condition in real time, and coordinates the operation of all inverter-based DG units in residential microgrid before reconnection to the main grid. A modified control scheme is proposed for single-phase inverters which turns them into smart inverters enable to interact with seamless transition algorithm. The proposed approach synchronizes each phase voltage with its respective grid-side voltage in order to seamlessly reconnect the residential microgrid to the main grid. Case study results are carried out in PSCAD/EMTDC environment to verify the validity of proposed method.

Pilehvar, Mohsen S.↗
DOE OSTI2021

Constant Frequency ZVS PWM Converter

In this paper, a simple yet novel buck or boost adaptive zero-voltage switching (ZVS) converter topology is proposed for soft switching pulse-width modulation (PWM) dc / dc converters. The converter is designed for the high switching frequency that can achieve high efficiency by reducing switching losses for the entire load range at low and high power. Besides, the output at the load terminals is maintained by a PWM signal at a fixed switching frequency, a phase shift signal between converter ports (legs) controls the system circulating current in order to provide the ZVS condition in all load conditions. With the proposed controller, the converter, thus, is suitable for high switching frequency and high-power applications with the small volume. The proposed dc / dc converter operation is analyzed, designed, and confirmed by simulation results for 240 V input, 400 V / 5 A output, and 200 kHz operating frequency at full load.

Asa, Erdem↗
DOE OSTI2024

A Neural Network-Based Power Mismatch Elimination Strategy for Integrated Solar and ESS AC/DC Systems (MARS)

The multiport autonomous reconfigurable solar power plant (MARS) is a promising concept for the integration of photovoltaic (PV) and energy storage system (ESS) to the transmission ac grid and a high-voltage direct current (HVdc) link. The presence of PV and ESS in each arm of the MARS results in uneven distribution of active power among different submodules (SMs), thereby leading to unbalanced SM capacitor voltages and potentially compromising the system stability. Moreover, in the case of partial shadings, shaded PV SMs will suffer from decreased power injections causing power mismatch in the MARS system. To address this issue, a neural-network-based power mismatch elimination (NNPME) strategy is proposed in this article. The proposed NNPME strategy optimizes ESS usage and leverages both dc and ac circulating currents to facilitate power transfer among the SMs, arms, and phases of the MARS system. Simulation and control hardware-in-the-loop (cHIL) experiments demonstrate the effectiveness of the proposed NNPME strategy. Compared with the traditional approaches, the proposed NNPME strategy can significantly enhance system efficiency and ensure stable and continuous operation, even in the presence of uneven power distribution within the MARS system.

14 SOLAR ENERGY↗