Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A spin-wave magnetometer with a positive feedback

In this work, we demonstrate experimentally the operation of a spin-wave magnetometer integrated into a circuit with a positive feedback. The circuit consists of the passive magnetic and active electric parts. The magnetic part includes a sensing element, which is a magnetic cross junction made of Y 3 Fe 2 (FeO 4 ) 3 . The electric part includes a non-linear amplifier and a phase shifter. The electric and magnetic parts are connected via micrometer size antennae. Spin waves are excited by two of these antennae while the output inductive voltage produced by the interfering spin waves is detected by the third antenna. Spin waves propagating in the orthogonal arms of the cross can accumulate significantly different phase shifts, depending on the direction and the strength of the external magnetic field. The output inductive voltage reaches its maximum in the case of constructive spin wave interference. The positive feedback provides further signal amplification. It appears possible to enhance the response function, compared to the passive circuits without a feedback, by a factor of ×100 without an increase in the noise level. The experimental data show a prominent response to the external magnetic field variation, exceeding 5 x 10 3 V/T. The intrinsic noise spectral density of the device can be as low as 10 -16 V 2 /Hz. The estimated sensitivity of the prototype device is 2 x 10 -12 T/√Hz at room temperature. We argue that spin-wave magnetometers can potentially be as sensitive as SQUIDs while operating at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrochemical behavior and separation of iodide in molten LiF-NaF-KF melt

This work studied the electrochemical behavior of iodide in molten LiF-NaF-KF mixture and the separation of iodide from the molten salt at 973 K using a graphite working electrode. The cyclic voltammetry (CV) and chronoamperometry (CA) measurements indicated an anodic passivation layer was formed on the graphite electrode in this melt and the layer blocked the charge transfer across the electrolyte/electrode interface. However, the added I- ions could pass through the passivation layer and were oxidized at the graphite electrode. The characterization of the obtained products proved that iodide ions was efficiently oxidized to I2 gas during electrolysis. Furthermore, the graphite anode showed excellent stability without any obvious change in dimensions after electrolysis, which showed the high current efficiency of I2 evolution reaction. Thus, the graphite electrode was possible to be served as an excellent anode to separate other anions (such as Br) from molten fluoride salts.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of chromium on corrosion resistance of Ni-Cr-Mo-Gd alloys in seawater

Neutron absorbing materials are being considered within commercial spent nuclear fuel disposal canisters to maintain nuclear subcriticality in storage. To select candidate alloys for the canisters, both neutron absorption and corrosion resistance should be considered. This work examines corrosion resistance of Ni-Cr-Mo-Gd alloys developed specifically for neutron absorption. The addition of Gd results in a secondary gadolinide phase (Ni 5 Gd) that significantly changes the corrosion properties. Testing was performed primarily in seawater at 30°C. Seawater was selected as the most prevalent terrestrial brine and is characterized by a high chloride concentration. Various electrochemical corrosion techniques were carried out to evaluate Ni-Cr-Mo-Gd alloys with different Cr compositions and investigate the role of Ni 5 Gd phase on corrosion behavior. C22 was included as a benchmark material, due to the similarity in composition and the significant corrosion data available. Here, test results showed a tendency to passivate over time which is attributed to dissolution of surface exposed Ni 5 Gd phase. Cross-sectional analysis indicated that dissolution could penetrate hundreds of micrometers deep under aggressive conditions. It was found that higher Cr variant (21.01%) showed much shallower impact, suggesting Cr prevented primary phase corrosion and thus reduced Ni 5 Gd phase dissolution. Acid pickling of the specimens showed much less dissolution for a higher Cr material and suggested some primary phase dissolution for the low Cr specimen. Acid pickled specimens showed positive shifts in the repassivation potential, suggesting increased surface passivation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Improving Efficiency and Stability of Perovskite Solar Cells Enabled by A Near-Infrared-Absorbing Moisture Barrier

Simultaneously improving device efficiency and stability is the most important issue in perovskite solar cell (PSC) research. Here, we strategically introduce a multi-functional interface layer (MFIL) with integrated roles of: (1) electron transport, (2) moisture barrier, (3) near-infrared photocurrent enhancement, (4) trap passivation, and (5) ion migration suppression to enhance the device performance. The narrow-band-gap non-fullerene acceptor, Y6, was screened out to replace the most commonly used PCBM in the inverted PSCs. A significantly improved power conversion efficiency of 21.0% was achieved, along with a remarkable stability (up to 1,700 h) without encapsulation under various external stimuli (light, heat, and moisture). Furthermore, systematic studies of the molecular orientation or passivation and the charge carrier dynamics at the interface between perovskite and MFIL were presented. These results offer deep insights for designing advanced interlayers and establish the correlations between molecular orientation, interface molecular bonding, trap state density, non-radiation recombination, and the device performance.

14 SOLAR ENERGY↗
DOE OSTI2020

High-Efficiency Silicon Heterojunction Solar Cells: Materials, Devices and Applications

Photovoltaic (PV) technology offers an economic and sustainable solution to the challenge of increasing energy demand in times of global warming. The world PV market is currently dominated by the homo-junction crystalline silicon (c-Si) PV technology based on high temperature diffused p-n junctions, featuring a low power conversion efficiency (PCE). Recent years have seen the successful development of Si heterojunction technologies, boosting the PCE of c-Si solar cells over 26%. This article reviews the development status of high-efficiency c-Si heterojunction solar cells, from the materials to devices, mainly including hydrogenated amorphous silicon (a-Si:H) based silicon heterojunction technology, polycrystalline silicon (poly-Si) based carrier selective passivating contact technology, metal compounds and organic materials based dopant-free passivating contact technology. The application of silicon heterojunction solar cells for ultra-high efficiency perovskite/c-Si and III-V/c-Si tandem devices is also reviewed. In the last, the perspective, challenge and potential solutions of silicon heterojunction solar cells, as well as the tandem solar cells are discussed.

14 SOLAR ENERGY↗
DOE OSTI2020

Over 11% Efficient Eco-Friendly Kesterite Solar Cell: Effects of S-Enriched Surface of Cu2ZnSn(S,Se)4 Absorber and Band Gap Controlled (Zn,Sn)O Buffer

For high efficiency kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cell, CdS thin film was usually used as a buffer layer. However, due to the toxicity of Cd and pollution problems involved from the solution-based chemical bath deposition, eco-friendly high efficiency CZTSSe solar cell with Cd-free buffer is necessary. As an Cd-free buffer layer, we investigated (Zn,Sn)O (ZTO) film deposited by sputtering method. In order to achieve high power conversion efficiency, we controlled energy band gaps of CZTSSe absorber as well as ZTO buffer, which was required to optimize conduction band offset (CBO) between the absorber and the buffer and to increase open circuit voltage (Voc) and fill factor (FF). The CBO was optimized by controlling the band gap of ZTO. By varying the Sn/(Zn + Sn) ratio and its deposition temperature, band gap of ZTO was successfully adjusted. Experimental and computational calculation results showed that solar cell performance was strongly affected by the CBO between absorber and buffer. Besides CBO matching, larger band gap of ZTO improved short circuit current density (Jsc) with enhanced external quantum efficiency value in blue photon spectrum range. As an additional way to improve power conversion efficiency of solar cell, band graded CZTSSe absorber was developed by using spray-based two-step process. The sprayed CZTSSe film was engineered to have S-enriched surface, which makes surface band gap widened and surface passivated, and resultantly increases Voc, Jsc and fill factor (FF). By controlling band gaps of both CZTSSe absorber and ZTO buffer, we obtained 11.22% environment-friendly CZTSSe solar cell without MgF2 anti-reflection coating.

(Zn↗
DOE OSTI2024

Evaluation of material accountancy techniques for 233 Pa from thorium nuclear fuels

Thorium is a promising alternative to uranium as nuclear fuel with advantages such as higher abundance, lower production of long-lived transuranic elements, and potentially better proliferation resistance. However, thorium presents a potential pathway for proliferation where produced 233 Pa can be diverted for the clandestine production of safeguarded 233 U. To prevent this, the ability to detect and measure 233 Pa must be assessed. This paper reviews several nuclear material accountancy techniques to determine their suitability for detecting 233 Pa extracted from irradiated thorium fuel. Hybrid K-edge densitometry and passive gamma spectroscopy have been found to be the best options based on technology maturity, cost, accuracy, and acquisition time. Thorium can be used in various reactor designs such as pressurized water reactors (PWRs), Canada deuterium uranium (CANDU) reactors, and molten salt reactors (MSRs). Therefore, thorium-uranium oxide fueling was modeled for three representative reactors (PWR, CANDU, MSR), burning the fuel to 47 GWd/MTHM for PWR, 19 GWd/MTHM for CANDU, and at a steady power of 52.711 MW/MTHM for MSR. Within each model, the protactinium element in the used fuel was extracted and its isotopic content analyzed. Simulated results indicated that 233 Pa can be detected using passive gamma spectroscopy in each fuel type at all decay times (0–300 days) following separation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Conceptual design study of neutron detectors for safeguards measurement of an irradiated pebble

Nuclear material control and accounting (MC&A) of pebble-bed reactors (PBRs) is challenging because a PBR utilizes hundreds of thousands of identical, unmarked pebbles that are continuously recirculated through the core. To develop tools that enable the implementation of international safeguards, especially in the context of MC&A of spent pebbles, we designed and simulated three neutron detection concepts to determine fissile content in individual pebbles: a differential die-away (DDA) detector, a californium interrogation prompt neutron (CIPN) detector, and a passive neutron albedo reactivity (PNAR) detector using Monte Carlo calculations. Burnup calculations were performed on the spent pebbles from the PBMR-400 classic PBR. The varying neutron and gamma source terms, and isotopic compositions in the spent pebbles calculated at various burnup levels were used in the neutron detector models. DDA was found to be sensitive to the number of passes a pebble has had through the core and to the fissile content contained in a spent pebble. Optimization in the DDA design further increased the neutron count rates and thus reduced counting uncertainty. Meanwhile, passive neutron counting using the same detector body could distinguish pebbles with different numbers of passes, but its response was dominated by neutron-emitting actinides and was not sensitive to fissile content. On the other hand, the PNAR technique was not viable for a single pebble but performed reasonably for a 27-pebble array, which suggested potential use for verification measurements of containers filled with 27 or more spent pebbles.

CIPN↗
DOE OSTI2020

Humidity sensitivity of large area silicon sensors: Study and implications

The production of large area sensors is one of the main challenges that the ATLAS collaboration faces for the new Inner-Tracker full-silicon detector. During the prototype fabrication phase for the High Luminosity Large Hadron Collider upgrade, several ATLAS institutes observed indications of humidity sensitivity of large area sensors, even at relative humidities well below the dew point. Specifically, prototype Barrel and End-Cap silicon strip sensors fabricated in 6-inch wafers manifest a prompt decrease of the breakdown voltage when operating under high relative humidity, adversely affecting the performance of the sensors. In addition to the investigation of these prototype sensors, a specific fabrication batch with special passivation is also studied, allowing for a deeper understanding of the responsible mechanisms. Here we present an extensive study of this behaviour on large area sensors. The locations of the hotspots at the breakdown voltage at high humidity are revealed using different infrared thermography techniques. Several palliative treatments are attempted, proving the influence of sensor cleaning methods, as well as baking, on the device performance, but no improvement on the humidity sensitivity was achieved. Furthermore, a study of the incidence of the sensitivity in different batches is also presented, introducing a hypothesis of the origins of the humidity sensitivity associated to the sensor edge design, together with passivation thickness and conformity. Several actions to be taken during sensor production and assembly are extracted from this study, in order to minimize the impact of humidity sensitivity on the performance of large area silicon sensors for High Energy Physics experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Control-inspired design and power optimization of an active mechanical motion rectifier based power takeoff for wave energy converters

Ocean waves have high energy density and are persistent and predictable. Yet, converting wave energy to a useable form remains challenging. A significant hurdle is the oscillatory nature of waves resulting in the alternating loads, which necessitate the use of rectification at some stage of the energy conversion. This research effort presents a novel design of active mechanical motion rectifier (AMMR) for the power takeoff (PTO), which provides enhanced controllability and better power performance when compared to passive mechanical motion rectifiers (MMR). Inspired by transistors used in synchronous electrical rectifiers, the proposed design uses controllable electromagnetic clutches in the mechanical transmission to allow active engagement-disengagement control; thus, rectifying the oscillatory motion into a unidirectional rotation for high energy conversion efficiency and allowing the generator in unidirectional rotation to control the bidirectional wave capture structure for maximizing the power output. A semi-analytical computational approach is developed to efficiently evaluate the optimal power achieved using the proposed AMMR-based PTO and active control. It is found that the AMMR-based PTO design yields a higher optimal power than the previous passive MMR design across the wave spectrum. The influences of generator inertia and reactive power are discussed. Furthermore, the effects of control parameters on the power output and the optimal trajectories are analyzed. Wave tank tests with the AMMR prototype demonstrated the effectiveness of AMMR based PTO design and validated the numerical analysis.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Impact of acetic acid exposure on metal contact degradation of different crystalline silicon solar cell technologies

Degradation due to acetic acid in photovoltaic (PV) modules has been a commonly observed phenomenon for both damp-heat exposure and outdoor operations. Acetic acid is a degradation byproduct of ethylene-vinyl acetate (EVA), a common module encapsulant. To address this issue, robust metallization pastes and cell technologies are being developed. However, it is important to assess how these technologies perform in an acetic acid environment and withstand degradation before they are implemented in the solar market. In this work, we investigate the impact of acetic acid exposure on four different cell groups: monofacial passivated emitter and rear contact (PERC) cells with advanced telluride-based front contact pastes, bifacial PERC cells with novel aluminum rear contact pastes, bifacial tunnel oxide passivated contacts (TOPCon) cells, and silicon heterojunction (SHJ) cells. These cells were exposed to acetic acid for different time increments. The recombination losses were characterized by Suns-VOC, and multi-variate regression analysis of intensity-dependent photoluminescence (PL) images with Griddler AI. Resistive losses were tracked with the transmission line method (TLM). Samples showing severe performance degradation were selected for further materials characterization to understand the root cause. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to investigate the change in materials properties. Our study shows that the front contacts of the bifacial TOPCon cells and monofacial PERC cells were significantly affected by acetic acid exposure. Here, the SHJ cells were found to be the most stable.

14 SOLAR ENERGY↗
DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗
DOE OSTI2023

Degradation-related defect level in weathered silicon heterojunction modules characterized by deep level transient spectroscopy

Commercial silicon heterojunction photovoltaic modules, known as amorphous-silicon-based heterojunction with intrinsic thin-film layer (HIT) modules, show average degradation after 10 years in the field. HIT modules weathered outdoors in Colorado and Florida display mostly uniform decreases in intensity when mapped with photoluminescence (PL) imaging compared to a control module. Flash-table-based current-voltage curves show that degradation is dominated by voltage loss. Samples are cored from each of the modules, and deep level transient spectroscopy (DLTS) detects three electron-trap defect states in all modules with activation energies of electron emission from the defects of 0.07, 0.16, and 0.50 eV. DLTS measurements on the weathered modules show an additional deep-level, electron-trap defect state with an activation energy of 0.51 eV and a trap density of approximately 10 12 cm –3 . The capture rate is measured using varying short filling pulse times, and the resulting capture cross section is estimated to be 1.1x10 –16 cm 2 . The development of the weathering-related defect level correlates to decreases in carrier lifetime, PL intensity, and module voltage. Various depths of the space charge region are probed with increments in applied reverse bias and filling-pulse bias. Furthermore, this DLTS depth profiling shows a trend of trap density increasing with less applied reverse bias, suggesting that the weathering-related defect increases carrier recombination toward the interface between the bulk silicon wafer and the junction-forming amorphous-silicon passivation layers.

14 SOLAR ENERGY↗
DOE OSTI2023

Transforming the electronic properties of phosphorene through charge transfer superatomic doping

Phosphorene is a two-dimensional electron poor p-type semiconductor with great promise for applications in electronics and optoelectronics. Here, in this work, we propose how the two most important properties of a semiconductor, the band gap energy and the nature of carriers, can be controlled by changing the dimensionality or through charge transfer doping with metal-chalcogenide superatoms. Our studies on nanoribbons examine how the band gap can be changed by controlling the width of the ribbons. We investigate the stability and properties of bare and H-terminated nanoribbons. We show that small non-passivated ribbons can be metallic while the passivated ribbons show variation in the band gap energy as a function of the width of the ribbon. We next investigate an alternative approach to band gap and carrier control via doping with ligated metal-chalcogenide superatom clusters whose redox properties can be changed by ligand exchange. Our results obtained from deposition of Co 6 S 8 (PH 3 ) 5-n (CO) n clusters on a phosphorene support showed that the band gap energy can be controlled by exchanging the electron donating phosphine ligands with electron withdrawing CO. We then show that by depositing Re 6 Se 8 (PH 3 ) 5-n Cl n clusters, phosphorene can be converted into a p- or n- type semiconductor as the relative composition of ligands is changed. Our studies provide a novel approach to controlling carrier type and band gap in phosphorene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A modeling pipeline to relate municipal wastewater surveillance and regional public health data

As COVID-19 becomes endemic, public health departments require improved passive indicators, which are independent of voluntary testing data, to estimate the prevalence of COVID-19 in local communities. Quantification of SARS-CoV-2 RNA from wastewater has the potential to be a powerful passive indicator. However, connecting measured SARS-CoV-2 RNA to community prevalence is challenging. We have developed a generalized methodology to improve the predictive power of wastewater measurements and applied it to data collected from treatment plants in the Chicago area. We built and compared a set of multi-linear regression models, which incorporate pepper mild mottle virus (PMMoV) as a population biomarker, Bovine coronavirus (BCoV) as a recovery control, and wastewater system flow rate into a corrected estimate for SARS-CoV-2 RNA concentration. For our data, models with BCoV performed better than those with PMMoV, but all model estimates of prevalence significantly improved correlation compared to doing no correction. We also investigate the utility of RNA measurements in wastewater as a leading indicator of COVID-19 trends. We do this in a rolling manner for corrected wastewater data and for other prevalence indicators, and statistically compare the temporal relationship between new increases in the wastewater data and those in other prevalence indicators. We find that wastewater trends often lead other COVID-19 indicators in predicting new surges.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

High safety and cycling stability of ultrahigh energy lithium ion batteries

High-nickel layered oxide Li-ion batteries (LIBs) dominate the electric vehicle market, but their potentially poor safety and thermal stability remain a public concern. Here, we show that an ultrahigh-energy LIB (292 Wh kg –1 ) becomes intrinsically safer when a small amount of triallyl phosphate (TAP) is added to standard electrolytes. TAP passivates the electrode-electrolyte interfaces and limits the maximum cell temperature during nail penetration to 55°C versus complete cell destruction (>950°C) without TAP. The downside of this reliable safety solution is higher interfacial impedance and hence lower battery power; however, thermal modulation for battery operation around 60°C can restore power completely. When cycled at 60°C, the cell stabilized with TAP achieved 2,413 cycles at 76% capacity retention. Such an unconventional combination of interface-passivating electrolyte additive with cell thermal modulation renders the most energy-dense LIBs even safer than LiFePO 4 chemistry, while enjoying high power and cycling stability concurrently.

25 ENERGY STORAGE↗
DOE OSTI2025

Reaction-Induced Fracturing of Porous Carbonate Rocks during Volume-Increasing Replacement by Witherite

Volume-increasing replacement reactions can lead either to fracturing of the parent phase or to the formation of cohesive layers that passivate further reaction, but the factors that drive one outcome or the other are not understood. In this experimental study, we investigated the volume-increasing replacement of carbonate rocks (consisting of CaCO 3 and CaMg(CO 3 ) 2 ) of different porosity by witherite (BaCO 3 ). Samples were characterized using scanning electron microscopy, Raman spectroscopy, small-angle neutron/X-ray scattering, X-ray tomography, and scanning transmission electron microscopy. We observed the formation of a witherite reaction layer and witherite formation within pores and along grain boundaries. Despite this being a volume-increasing replacement reaction, newly formed witherite was porous, potentially allowing further replacement. Filled fractures were observed in the low-porosity carbonates, whereas witherite formed within pores in high-porosity carbonates. We conclude that fracturing of the parent phase versus passivation is contingent on the initial microstructure of the parent with an optimal degree of porosity required for fracturing.

Calcite↗
DOE OSTI2021

Surface-Induced Deprotonation of Thiol Ligands Impacts the Optical Response of CdS Quantum Dots

Cadmium chalcogenide quantum dots (QDs) passivated by thiol-based ligands exhibit several advantages in their applications in lighting, sensing, and imaging technologies. However, their emission is sensitive to thiol concentrations, pH conditions, and temperatures. Using calculations based on the density functional theory, we identify conditions for thiol/thiolate equilibrium at the CdS QD surface that either eliminate or introduce optically inactive hole trap states favoring or disfavoring the emission. Our calculations indicate much weaker interactions between the QD and protonated species (thiols), compared to their deprotonated counterparts (thiolates). Additionally, the surface of CdS QD facilitates the partial deprotonation of thiols, leading to the formation of an additional stable networking conformation where the proton is shared between the ligand and the QD surface. Thiolates strongly reduce the optical intensity of low-energy transitions in CdS QDs, contributing thiolate-localized hole trap states at the QD band gap. However, networking between the thiols and the surface, as well as the presence of native ligands such as primary amines, stabilize such trap states brightening the lowest optical transitions. This explains the increased emission of thiol-passivated QDs at lower concentrations in neutral or acidic solutions. Surface-mediated bias toward deprotonated species and their contribution to optically inactive states also rationalizes irreversible emission quenching and bleaching in the CdSe/CdS QDs exposed to high temperatures or intensive laser pulse.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗