Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “managed charging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Configuring the HYSPLIT Model for National Weather Service Forecast Office and Spaceflight Meteorology Group Applications

The National Weather Service Forecast Office in Melbourne, FL (NWS MLB) is responsible for providing meteorological support to state and county emergency management agencies across East Central Florida in the event of incidents involving the significant release of harmful chemicals, radiation, and smoke from fires and/or toxic plumes into the atmosphere. NWS MLB uses the National Oceanic and Atmospheric Administration Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model to provide trajectory, concentration, and deposition guidance during such events. Accurate and timely guidance is critical for decision makers charged with protecting the health and well-being of populations at risk. Information that can describe the geographic extent of areas possibly affected by a hazardous release, as well as to indicate locations of primary concern, offer better opportunity for prompt and decisive action. In addition, forecasters at the NWS Spaceflight Meteorology Group (SMG) have expressed interest in using the HYSPLIT model to assist with Weather Flight Rules during Space Shuttle landing operations. In particular, SMG would provide low and mid-level HYSPLIT trajectory forecasts for cumulus clouds associated with smoke plumes, and high-level trajectory forecasts for thunderstorm anvils. Another potential benefit for both NWS MLB and SMG is using the HYSPLIT model concentration and deposition guidance in fog situations.

Dreher, Joseph↗

Renovated Korean nuclear safety and security system: A review and suggestions to successful settlement

Questions of whether past nuclear regulatory body of Korea is not a proper system to monitor and check the country's nuclear energy policy and utilization have been raised. Moreover, a feeling of insecurity regarding nuclear safety after the nuclear accident in Japan has spread across the public. This has stimulated a renovation of the nuclear safety regime in Korea. The Nuclear Safety and Security Commission (NSSC) was launched on October 26, 2011 as a regulatory body directly under the President in charge of strengthening independence and nuclear safety. This was a meaningful event as the NSSC it is a much more independent regulatory system for Korea. However, the NSSC itself does not guarantee an enhanced public acceptance of the nuclear policy and stable use nuclear energy. This study introduces the new NSSC system and its details in terms of organization structure, appropriateness of specialty, budget stability, and management system. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Mechanisms of interfacial reactivity in near surface and extreme environments

The local water structure surrounding ions in aqueous solutions greatly affects their chemical properties such as reaction rates, ion association, and proton and electron transport. These properties result in the behavior of ions in natural aqueous environments. For example ore transport is facilitated by chloride ion pair formation and the reaction of ions in an interface is strongly dependent on the dehydration of the ion hydration shell. We are developing the use of high-­resolution XAFS observations and 1st principles based MD-­XAFS analysis (spectra simulated using 1st principle methods with no adjustable parameters, AIMD) to interpret the solution properties of strongly interacting aqueous solutes under arbitrary pressure and temperature conditions. In the 1st principle MD-­XAFS method density functional theory (DFT) based MD simulations(Car and Parrinello, 1985) are used to generate a large ensemble of structural snap shots of the hydration region. These are then used to generate scattering intensities. I emphasize three points about this novel approach to analyzing XAFS data. 1st: As illustrated in Figure 1, the level of agreement between the calculated and observed intensities is considerably higher than has been obtained by any XAFS analysis to date (note 2nd shell region, R> 2 Å). 2nd: This result was obtained from a parameter free simulation with no fitting of the interaction potentials to any data. This supports the use of these methods for more difficult environments and more complex solutes (polyions). 3rd: New information about the shell structure (Figure 1) is now available because of this more detailed agreement. We note also that both multiple scattering and second shell features are well represented in the analysis. As far as we know this is the 1st analysis of second shell structure and multiple scattering. Excellent agreement has been obtained for most of the third row metal ions: Ca 2+ , Zn 2+ , Cu 2+ , Ni 2+ , Co 2+ , Mn 2+ , Fe 3+ , Cr 3+ . Calculations on these systems are demanding because of their open electronic shells, and high ionic charge. Principal Investigator: Professor John Weare (University of California, San Diego) The prediction of the interactions of geochemical fluids with minerals, nanoparticles, and colloids under extreme near surface conditions of temperature (T) and pressure (P) is a grand challenge research need in geosciences (U.S. DOE 2007, Basic Research Needs for Geosciences: Facilitating the 21st Energy Systems.). To evaluate the impact of these processes on energy production and management strategies it is necessary to have a high level of understanding of the interaction between complex natural fluids and mineral formations. This program emphasizes 1st principle parameter free simulations of complex chemical processes in solutions, in the mineral phase, and in the interfaces between these phases The development of new computational tools (with emphasis on oxide materials and reaction dynamics) tailored to treat wide range of conditions and time scales experienced in such geochemical applications is has been developed. Because of the sensitivity of the interaction in these systems to electronic structure and local bonding environments, and of the need to describe bond breaking/formation, our simulations are based on interactions calculated at the electronic structure level (ab-initio molecular dynamics, AIMD). The progress in the computational aspects of program may be summarized in terms of the following themes (objectives); Development of efficient parameter free dynamical simulation technology based on 1st principles force and energy calculations especially adapted for geochemical applications (e.g., mineral, interfaces and aqueous solutions) (continuing program); Calculation of the dynamics of water structure of in the surface-water interface of transition metal oxides and oxihydroxides; and Development of improved (beyond DFT+GGA) electronic structure calculations for minerals and the interface region that more accurately calculate electron correlation, spin density, and localization. The focus of the program is also on the iron oxide and oxihydroxide minerals and Fe 2+ (aq)/Fe 3+ (cr) oxidation in the mineral solution interface region. These methods included the development of model Hamilitonian methods that can be solved to near convergence for single site models (DMFT) and many-body perturbation methods (MP2, GW); Development of time decomposition methods to extend time scales of molecular dynamics (MD) simulations and support the use of high complexity electronic structure calculations (MP2, CCSD(T)) of forces for use in dynamical simulations where very high chemical accuracy is required (microsolvated reactions in absorbed surface layers); and The development of a new linear scaling finite element solver for eigenvalue problem that supports solution of quantum problems with unusual potential and boundary values. Application progress of the above new simulation technology to problems of geochemical interests includes; The prediction of metal oxide surface structure and the reduction/oxidation of Fe 3+ (cr)/Fe 2+ (aq) in metal oxide (hematite, goethite)/solution interfaces. Result: water interacts strongly with the 001 Hematite surface; interaction of water with the 100 goethite is weak; The study of ion solvation and the composition of ion hydration shells under extreme conditions (focus on Fe 3+/2+ , Al 3+ and Mg 2+ and their hydroxide speciation). Result: Ion association in water solutions can be calculated from 1st principle methods. Efficient sampling of the free energy requires more development; The continued development of new high resolution analysis of XAFS scattering of disordered systems (particularly Al, Mg) and of XANES calculations for aqueous ions. Result: EXAFS spectra can be calculated to high accuracy with DFT level dynamic simulations; The exploration of electron localization and electron transport in metal oxides (highly correlated materials). Result: Proper description of electron localization requires levels of calculation beyond DFT; and Localization of electrons in DFT type Hamiltonians was studied. Result: For very Dirac high exchange new solutions (New unphysical bifrucations) to the eigenvalue problem are found. The program was highly collaborative involving faculty and students in mathematics, physics and computer science departments as well as coworkers at the Pacific Northwest National Laboratories (PNNL). The students in this program had the opportunity to develop skills in the development of methods, the implementation of method on high performance parallel computers and the application of these methods to problem in geochemical science. Much of the software that was developed was incorporated in the NWchem software package maintained by PNNL.

58 GEOSCIENCES↗

Federal Best Practices: Core Principles of Sustainable Fleet Management

This document is designed to help agency fleet managers understand and implement optimal petroleum reduction strategies for each fleet location by evaluating the most appropriate combination of the four core principles of sustainable fleet management: Right-sizing the fleet to agency mission by implementing a vehicle allocation methodology study; Minimizing vehicle miles traveled; Increasing fleet fuel efficiency by replacing inefficient vehicles with more fuel-efficient vehicles, maintaining vehicles, driving more efficiently, and avoiding excessive idling; Optimizing cost-effective alternative fuel use, including maximizing utilization of existing alternative fuel infrastructure, installing alternative fuel infrastructure where practical (including electric vehicle charging stations), and aligning deployment of alternative fuel vehicles with fueling infrastructure.

30 DIRECT ENERGY CONVERSION↗

Advances in Geologic Disposal System Modeling and Shale Reference Cases

The Spent Fuel and Waste Science and Technology (SFWST) Campaign of the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), Office of Fuel Cycle Technology (OFCT) is conducting research and development (R&D) on geologic disposal of spent nuclear fuel (SNF) and high level nuclear waste (HLW). Two high priorities for SFWST disposal R&D are design concept development and disposal system modeling (DOE 2011, Table 6). These priorities are directly addressed in the SFWST Generic Disposal Systems Analysis (GDSA) work package, which is charged with developing a disposal system modeling and analysis capability for evaluating disposal system performance for nuclear waste in geologic media (e.g., salt, granite, shale, and deep borehole disposal).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simulant Development of Potential 200 West Area Waste Feeds

Preliminary planning for retrieval, qualification, and pretreatment of waste in Hanford’s 200 West Area (200W) has begun as part of the West Area Risk Management project. Experimental studies to technically mature pretreatment process operations will likely be needed because of the uniqueness of 200W waste. Pacific Northwest National Laboratory formulated five simulants to represent 200W-qualified feed based on the preliminary flowsheet provided by Washington River Protection Solutions, LLC. The simulant recipes were devised using applicable historical information as a reference point to support the use of the flowsheet waste vectors, which were combined into five distinct groups. These five groups formed the basis for the liquid composition targets that were adapted into recipes using charged-balanced salt species. The liquid phase recipes were batched in 1-L quantities and analyzed at Pacific Northwest National Laboratory. Once confirmed to be stable, the liquid solutions were tested for compatibility with candidate solid components. Specific solid components were recommended based on cross-examining the proposed solid phases in the flowsheet with relevant data from the literature. Mixtures of solid components were added to aliquots of the liquid batches and sub-sampled to measure particle size distribution. The measured distribution was compared to independently created benchmark distributions appropriate for each simulant. This process was iterated until a solid phase composition that resulted in a representative particle size distribution was found. After the final compositions were confirmed, a suite of chemical and physical characterization data was collected. This report describes the simulant basis, formulation methodology, laboratory measurements, and data collected for the recipes recommended to represent 200W waste feeds.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Trace element migration during UF4 bomb reduction: Implications to metal fuel production, worker health and safety, and nuclear forensics

Understanding the migration of trace contaminants during the production of U metal is vital for fabricating advanced nuclear fuels, for managing worker health and safety at foundry and processing facilities, and for advancing nuclear forensic science. A common method used to produce actinide metals is the bomb reduction of suitable U precursors. Here, we report the results of a series of experiments designed to quantitatively track the trace contaminants Th, Ca, and, Mg through a bomb reduction of UF4 using a vacuum induction furnace. In this series, UF4 charges were doped with increasing levels of elemental Th from 0-1000 ppm Th/U. Following reduction, the metal ingot products and the associated slag and crucibles were individually digested and analyzed using inductively coupled plasma-mass spectrometry. The results show that Th fractionation occurred at all concentrations but was most significant, and near quantitative, in samples starting with Th concentrations below 100 ppm. Thorium was found to incorporate into the slag and crucible in roughly equal proportions. A significant amount of U and Ca migrated into the crucible walls, each correlated with Mg migration from the MgO crucible to the U metal product.

Reilly, Dallas D.↗

Multi-objective optimization with an integrated electromagnetics and beam dynamics workflow

In particle accelerators, RF cavities are used to accelerate charged particle beams to designed high energy for physical applications. In a typical accelerator design, the optimization of RF cavities and the optimization of beam dynamics are carried out in separate studies. For a more general and unrestricted accelerator design, a coupled optimization of the RF cavities and the beam parameters is required. For this coupled optimization problem, we have developed an integrated electromagnetics and beam dynamics workflow management system. Within this system, the geometries for a set of cavity components are first adjusted; the field modes are then computed with an electromagnetics program, and imported into a beam dynamics program for beam dynamics simulation. This workflow is encapsulated into a parallel multi-objective optimizer to achieve the integrated accelerator design optimization. A multi fidelity strategy is developed to improve the speed of the optimizer. Furthermore, this integrated global optimization capability is illustrated using a photoinjector design example and yields an improved design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for the National Park Service: Golden Gate National Recreation Area

Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energy's Idaho National Laboratory, is the lead laboratory for U.S. Department of Energy Advanced Vehicle Testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (ITSNA) to collect data on federal fleet operations as part of the Advanced Vehicle Testing Activity's Federal Fleet Vehicle Data Logging and Characterization study. The Advanced Vehicle Testing Activity study seeks to collect data to validate the utilization of advanced electric drive vehicle transportation. This report focuses on the Golden Gate National Recreation Area (GGNRA) fleet to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of plug-in electric vehicles (PEVs) into the agencies' fleets. Individual observations of these selected vehicles provide the basis for recommendations related to electric vehicle adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (PHEV) (collectively PEVs) can fulfill the mission requirements. GGNRA identified 182 vehicles in its fleet, which are under the management of the U.S. General Services Administration. Fleet vehicle mission categories are defined in Section 4, and while the GGNRA vehicles conduct many different missions, only two (i.e., support and law enforcement missions) were selected by agency management to be part of this fleet evaluation. The selected vehicles included sedans, trucks, and sport-utility vehicles. This report will show that battery electric vehicles and/or PHEVs are capable of performing the required missions and providing an alternative vehicle for support vehicles and PHEVs provide the same for law enforcement, because each has a sufficient range for individual trips and time is available each day for charging to accommodate multiple trips per day. These charging events could occur at the vehicle home base, high-use work areas, or intermediately along routes that the vehicles frequently travel. Replacement of vehicles in the current fleet would result in significant reductions in the emission of greenhouse gases and petroleum use, while also reducing fuel costs. The San Francisco Bay Area is a leader in the adoption of PEVs in the United States. PEV charging stations, or more appropriately identified as electric vehicle supply equipment, located on the GGNRA facility would be a benefit for both GGNRA fleets and general public use. Fleet drivers and park visitors operating privately owned PEVs benefit by using the charging infrastructure. ITSNA recommends location analysis of the GGNRA site to identify the optimal placement of the electric vehicle supply equipment station. ITSNA recognizes the support of Idaho National Laboratory and ICF International for their efforts to initiate communication with the National Parks Service and GGNRA for participation in the study. ITSNA is pleased to provide this report and is encouraged by the high interest and support from the National Park Service and GGNRA personnel.

99 GENERAL AND MISCELLANEOUS↗

Concrete Thermal Energy Storage Enabling Flexible Operation without Coal Plant Cycling

The work described in this report is responsive to the Office of Fossil Energy program “Energy Storage for Fossil Power Generation.” The pilot plant built as a result of this project demonstrated the feasibility and performance of a concrete thermal energy storage (CTES) system integrated with a supercritical coal power plant. The 10 MWh electrical (>25 MWh thermal) CTES unit, developed by Storworks Power, was designed to enable flexible operation of coal plants without cycling damage. The project's key technical achievements showcase a significant advancement in energy storage technology. A modular CTES system using 42 “Bolderblocs” units was successfully designed and constructed at Alabama Power’s Plant Gaston Unit 5, with each block containing embedded stainless-steel coils in specialized, cost-effective high-temperature concrete. The system interfaced seamlessly with the plant's 3500 psig (241 barg), 1000°F (538°C) supercritical steam, demonstrating operational flexibility. Over 86 full cycles, the CTES exhibited rapid charging and discharging capabilities, effectively mimicking steam turbine feed conditions and handling varying load profiles and storage durations. Performance validation confirmed the system's ability to consistently meet design target steam conditions of 75 bar-a and ~400°C for nominal baseline discharge. The concrete material withstood repeated thermal cycling without degradation, validating earlier lab-scale tests. Integration of balance of plant components, including a condensate management system with storage tank and air-cooled condenser, minimized plant interfaces and water consumption. A robust control scheme ensured safe, automated operation across various scenarios. Key learnings from the project were invaluable: 1. Initial concrete drying and commissioning procedures were refined for future deployments, enhancing efficiency in subsequent installations. 2. System flexibility exceeded expectations, with rapid response to changing conditions. 3. Design improvements were identified including optimized insulation and piping that will enhance overall system efficiency in future deployments 4. Full cycle thermal roundtrip efficiencies exceeded 88%. While the roundtrip electrical efficiency was somewhat limited by known challenges using input steam, such constraints may be mitigated by swapping steam for hot air as thermal input. 5. A summary of key performance parameters for the pilot test and predicted performance of a full scale commercial system with specified improvements determined from the pilot are shown in Section 8. The project faced challenges, including COVID-19 delays and host plant availability constraints. However, these were overcome through adaptive planning and execution. The successful management of these obstacles demonstrated the resilience and adaptability of the project team and the robustness of the CTES technology. This successful pilot demonstrates the potential for CTES to enhance coal plant flexibility, supporting grid stability as renewable penetration increases. The validated design and operational data provide a solid foundation for scaling up to utility-scale implementations, potentially transforming how thermal plants operate in evolving energy landscapes. The system's ability to rapidly respond to changing grid conditions while maintaining high efficiency makes it a promising solution for balancing intermittent renewable energy sources. Furthermore, the project highlighted the potential for even greater efficiencies in future iterations. The use of air as an input medium could potentially eliminate the limitations observed with steam input, opening new possibilities for energy storage applications beyond coal plant integration. In conclusion, this pilot project not only achieved its primary goals but also uncovered additional benefits and potential applications of the CTES technology. It represents a significant step forward in addressing the challenges of grid stability and flexibility in an increasingly renewable-driven energy landscape.

01 COAL, LIGNITE, AND PEAT↗

The added economic and environmental value of plug-in electric vehicles connected to commercial building microgrids

Connection of electric storage technologies to smartgrids or microgrids will have substantial implications for building energy systems. In addition to potentially supplying ancillary services directly to the traditional centralized grid (or macrogrid), local storage will enable demand response. As an economically attractive option, mobile storage devices such as plug-in electric vehicles (EVs) are in direct competition with conventional stationary sources and storage at the building. In general, it is assumed that they can improve the financial as well as environmental attractiveness of renewable and fossil based on-site generation (e.g. PV, fuel cells, or microturbines operating with or without combined heat and power). Also, mobile storage can directly contribute to tariff driven demand response in commercial buildings. In order to examine the impact of mobile storage on building energy costs and carbon dioxide (CO2) emissions, a microgrid/distributed-energy-resources (DER) adoption problem is formulated as a mixed-integer linear program with minimization of annual building energy costs applying CO2 taxes/CO2 pricing schemes. The problem is solved for a representative office building in the San Francisco Bay Area in 2020. By using employees' EVs for energy management, the office building can arbitrage its costs. But since the car battery lifetime is reduced, a business model that also reimburses car owners for the degradation will be required. In general, the link between a microgrid and an electric vehicle can create a win-win situation, wherein the microgrid can reduce utility costs by load shifting while the electric vehicle owner receives revenue that partially offsets his/her expensive mobile storage investment. For the California office building with EVs connected under a business model that distributes benefits, it is found that the economic impact is very limited relative to the costs of mobile storage for the site analyzed, i.e. cost reductions from electric vehicle connections are modest. Nonetheless, this example shows that some economic benefit is created because of avoided demand charges and on-peak energy. The strategy adopted by the office building is to avoid these high on-peak costs by using energy from the mobile storage in the business hours. CO2 emission reduction strategy results indicate that EVs' contribution at the selected office building are minor.

25 ENERGY STORAGE↗

An Overview of Public Domain Tools for Measuring the Sustainability of Environmental Remediation - 12060

The application of sustainability principles to the investigation and remediation of contaminated sites is an area of rapid development within the environmental profession, with new business practices, tools, and performance standards for identifying, evaluating, and managing the 'collateral' impacts of cleanup projects to the environment, economy and society coming from many organizations. Guidelines, frameworks, and standards of practice for 'green and sustainable remediation' (GSR) have been released and are under development by the Sustainable Remediation Forum (SURF), the American Society for Testing Materials (ASTM), the Interstate Technology Roundtable Commission (ITRC) and other organizations in the U.S. and internationally. In response to Executive Orders from the President, Federal government agencies have developed policies, procedures and guidelines for evaluating and reporting the sustainability of their environmental restoration projects. Private sector companies in the petroleum, utility, manufacturing, defense, and other sectors are developing their own corporate GSR programs to improve day-to-day management of contaminated sites and to support external reporting as part of their corporate social responsibility (CSR) efforts. The explosion of mandates, policy, procedures and guidance raises the question of how to determine whether a remediation technology or cleanup approach is green and/or sustainable. The environmental profession has responded to this question by designing, developing and deploying a wide array of tools, calculators, and databases that enable regulatory agencies, site managers and environmental professionals to calculate the collateral impacts of their remediation projects in the environmental, social, and economic domains. Many of these tools are proprietary ones developed by environmental engineering/consulting firms for use in their consulting engagements and/or tailored specifically to meet the needs of their clients. When it comes to the public domain, Federal government agencies are spearheading the development of software tools to measure and report emissions of air pollutants (e.g., carbon dioxide, other greenhouse gases, criteria air pollutants); consumption of energy, water and natural resources; accident and safety risks; project costs and other economic metrics. Most of the tools developed for the Government are available to environmental practitioners without charge, so they are growing in usage and popularity. The key features and metrics calculated by the available public-domain tools for measuring the sustainability of environmental remediation projects share some commonalities but there are differences amongst the tools. The SiteWise{sup TM} sustainability tool developed for the Navy and US Army will be compared with the Sustainable Remediation Tool (SRT{sup TM}) developed for the US Air Force (USAF). In addition, the USAF's Clean Solar and Wind Energy in Environmental Programs (CleanSWEEP), a soon-to-be-released tool for evaluating the economic feasibility of utilizing renewal energy for powering remediation systems will be described in the paper. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigation of design principles for metal-binding and conductive protein assemblies

Throughout the lifetime of this initiative, including renewals, we focused on understanding the fundamental principles of protein-protein interface design that enable predictable and modular spatial and kinetic control of multi-component protein self-assembly in 1D, 2D, and 3D, including the interface with inorganic materials, small molecules, and metal ions. We designed individual protein components that bind specific metal ions, including REEs and transport ions across lipid membranes. We created helical 1D filaments of repeating units with programmed periodicity, pitch, and multi-component environmentally responsive self-assembling protein fibers. We showed that these filaments reversibly assemble and disassemble under specific pH conditions and created end-specific caps that independently tune the balance of attachment and detachment rates at each terminus of the filament. Using similar filaments, we succeeded in binding arrays of heme and chlorophyll molecules and assembling patterned helical coatings around carbon nanotubes in efforts to create de novo conductive nanowires. By arraying REE binding sites in a large circular tandem array with a repeat protein-based cyclic oligomer, we created a molecular scaffold for superradiance and paramagnetic quantum sensing. We created a range of one-component and two-component self-assembling 2D arrays and showed that when designed to engage cell receptors, these arrays can control cell behavior from outside the cell signal to inside the cell. We designed helical repeat proteins with variable lengths displaying charged residues in a pattern matched to the cation lattice of mica. achieved a range of ordered states with an epitaxial match to the underlying crystal lattice. We further applied the learned principles of protein-induced biomineralization to design proteins with an interface lattice matching CaCO 3 and guide the formation of specific crystal forms of CaCO 3 from solution, a significant advance toward the global need to manage carbon. In all cases of mineral lattice matching and biomineralization, we followed assembly using molecularly resolved in situ AFM imaging and extracted information about assembly pathways and energetics, applying deep learning to quantify the dynamics of protein self-organization. We developed techniques for using dynamic metal-dependent interfaces on protein nanopores for discriminatively sensing dilute REEs in solution and demonstrated the use of strong metal-binding interfaces to drive nanocage disassembly for conditional nanocompartmentalization applications. This grant supported 11 people, including Asim Bera, Evans Brackenbrough, Andrew Borst, Nikita Hanikel, Timothy Huddy, Emily Joyce, Alex Young-Seug Kang, Ryan Kibler, Joshua Morris Lubner, Harley Pyles, and Shuai Zhang. The research effort culminated in the production of published papers and theses. Electronic Thesis/Dissertation are distributed by ProQuest/UMI Dissertation Publishing and made available on an open access basis through UW Libraries ResearchWorks Service.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spacecraft Software Maintenance: An Effective Approach to Reducing Costs and Increasing Science Return

Flight software is a mission critical element of spacecraft functionality and performance. When ground operations personnel interface to a spacecraft, they are typically dealing almost entirely with the capabilities of onboard software. This software, even more than critical ground/flight communications systems, is expected to perform perfectly during all phases of spacecraft life. Due to the fact that it can be reprogrammed on-orbit to accommodate degradations or failures in flight hardware, new insights into spacecraft characteristics, new control options which permit enhanced science options, etc., the on- orbit flight software maintenance team is usually significantly responsible for the long term success of a science mission. Failure of flight software to perform as needed can result in very expensive operations work-around costs and lost science opportunities. There are three basic approaches to maintaining spacecraft software--namely using the original developers, using the mission operations personnel, or assembling a center of excellence for multi-spacecraft software maintenance. Not planning properly for flight software maintenance can lead to unnecessarily high on-orbit costs and/or unacceptably long delays, or errors, in patch installations. A common approach for flight software maintenance is to access the original development staff. The argument for utilizing the development staff is that the people who developed the software will be the best people to modify the software on-orbit. However, it can quickly becomes a challenge to obtain the services of these key people. They may no longer be available to the organization. They may have a more urgent job to perform, quite likely on another project under different project management. If they havn't worked on the software for a long time, they may need precious time for refamiliarization to the software, testbeds and tools. Further, a lack of insight into issues related to flight software in its on-orbit environment, may find the developer unprepared for the challenges. The second approach is to train a member of the flight operations team to maintain the spacecraft software. This can prove to be a costly and inflexible solution. The person assigned to this duty may not have enough work to do during a problem free period and may have too much to do when a problem arises. If the person is a talented software engineer, he/she may not enjoy the limited software opportunities available in this position; and may eventually leave for newer technology computer science opportunities. Training replacement flight software personnel can be a difficult and lengthy process. The third approach is to assemble a center of excellence for on-orbit spacecraft software maintenance. Personnel in this specialty center can be managed to support flight software of multiple missions at once. The variety of challenges among a set of on-orbit missions, can result in a dedicated, talented staff which is fully trained and available to support each mission's needs. Such staff are not software developers but are rather spacecraft software systems engineers. The cost to any one mission is extremely low because the software staff works and charges, minimally on missions with no current operations issues; and their professional insight into on-orbit software troubleshooting and maintenance methods ensures low risk, effective and minimal-cost solutions to on-orbit issues.

Shell, Elaine M.↗

Pollution Control Device

BHA Group Inc.'s PrecipTech Power Guard SQ-200 automatic voltage controller, combined with a remote computer, is an automatic management system for smoke-cleaning precipitators. It is the second generation of the SQ 100 developed at Langley Research Center, and was commercialized by two NASA employees. An electrostatic precipitator cleans the smoke by removing particulate matter from smokestack gases before gases are expelled into the atmosphere. Smokestack gas is passed through a precipitator chamber and exposed to an electrostatic field; dust particles in the gas become electrically charged, migrate to collection surfaces and are "captured." Developed under a NASA program seeking a way to dispose refuse, the system monitors sparking, automatically adjusts to changes in operating conditions and does not require a skilled operator.

Source record↗

Software With Strong Ties to Space

TieFlow is a simple but powerful business process improvement solution. It can automate and simplify any generic or industry-specific work process, helping organizations to transform work inefficiencies and internal operations involving people, paper, and procedures into a streamlined, well-organized, electronicbased process. TieFlow increases business productivity by improving process cycle times. The software can expedite generic processes in the areas of product design and development, purchase orders, expense reports, benefits enrollment, budgeting, hiring, and sales. It can also shore up vertical market processes such as claims processing, loan application and processing, health care administration, contract management, and advertising agency traffic. The processes can be easily and rapidly captured in a graphical manner and enforced together with rules pertaining to assignments that need to be performed. Aside from boosting productivity, TieFlow also reduces organizational costs and errors. TieFlow was developed with Small Business Innovation Research (SBIR) assistance from Johnson. The SBIR support entitles all Federal Government agencies to utilize the TieFlow software technology free of charge. Tietronix emphasizes that TieFlow is an outstanding workflow resource that could produce dramatic productivity and cost improvements for all agencies, just as it has done and continues to do for NASA. The Space Agency is currently using the software throughout several mission-critical offices, including the Mission Operations Directorate and the Flight Director s Office, for worldwide participation of authorized users in NASA processes. At the Flight Director s Office, TieFlow allows personnel to electronically submit and review changes to the flight rules carried out during missions.

Source record↗

A Fully Integrated and Self-Powered Smartwatch for Continuous Sweat Glucose Monitoring

Wearable devices for health monitoring and fitness management have foreseen a rapidly expanding market, especially those for noninvasive and continuous measurements with real-time display that provide practical convenience and eliminated safety/infection risks. In this research, a self-powered and fully integrated smartwatch that consists of flexible photovoltaic cells and rechargeable batteries in the forms of a “watch strap”, electrochemical glucose sensors, customized circuits, and display units integrated into a “dial” platform is successfully fabricated for real-time and continuous monitoring of sweat glucose levels. The functionality of the smartwatch, including sweat glucose sensing, signal processing, and display, can be supported with the harvested/converted solar energy without external charging devices. The Zn-MnO 2 batteries serve as intermediate energy storage units and the utilization of aqueous electrolytes eliminated safety concerns for batteries, which is critical for wearable devices. Such a wearable system in a smartwatch fashion realizes integration of energy modules with self-powered capability, electrochemical sensors for noninvasive glucose monitoring, and in situ and real-time signal processing/display in a single platform for the first time. The as-fabricated fully integrated and self-powered smartwatch also provides a promising protocol for statistical study and clinical investigation to reveal correlations between sweat compositions and human body dynamics.

47 OTHER INSTRUMENTATION↗

Understanding Your Utility Bills: Natural Gas

As a fossil fuel NG is a colorless and odorless gas in its natural state and is one of the cleanest burning hydrocarbons. The factors that contribute to the popularity of natural gas in the US manufacturing sector include ease of availability, clean burning properties, market deregulation, and increased domestic production. Analyzing natural gas (NG) bills can sometimes pose unique problems. Learning to read your utility bills and understand why your utility charges different fees is critical in maximizing your cost savings through energy efficiency. A key to creating a baseline is collecting and analyzing natural gas utility data. Historical data from NG bills can identify trends and help to find the baseline usage for a manufacturing operation. This guide intends to help Better Plant Program partners in understanding natural gas bills and analyzing usage to reduce costs. The guide focuses on natural gas production and transportation, understanding key charges on bills, different rate structures, and saving opportunities. A fictitious worked out example in the final section demonstrates how readers could go about analyzing natural gas bills.

03 NATURAL GAS↗