Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Long-Length SiC/SiC Tube Irradiation Experiment at LWR Temperatures Inserted into HFIR

This report describes the pre-irradiation characterization and successful assembly of a High Flux Isotope Reactor (HFIR) irradiation experiment designed to assess radiation-induced lateral bowing of silicon carbide fiber–reinforced, silicon carbide matrix composite (SiC/SiC) components under a radial fast neutron flux gradient at representative light-water reactor (LWR) temperatures of approximately 300 °C. The over-arching goal of this work is to validate thermomechanical models of SiC/SiC composite fuel assembly distortion used to predict the extent of lateral bowing and dose at which bowing reaches a maximum value. Ultimately, these models are used to ensure that fuel assembly distortion does not block coolant channels, interfere with control rod/blade movements, and/or impact local reactivity. The experiment contains six cladding tube specimens that are approximately 558.5 mm long with representative pressurized water reactor (PWR) outer and inner diameters of 9.5 mm and 7.5 mm, respectively. The specimens were thoroughly characterized prior to irradiation using traditional dimensional inspection and surface profilometry so that these measurements can later be compared with similar measurements that will be made post-irradiation to determine radiation-induced deformations. Furthermore, fine engraving markers were inscribed along the outer surfaces of the specimen and mapped using analytic photography and a three-dimensional stage. This technique allowed for accurate measurements of the marker spacings, which can be compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. A light curtain optical micrometer was also employed to measure the pre-irradiation bowing of each specimen. The experiment was successfully assembled and inserted into position VXF-19 for HFIR cycle 516, which began May 12, 2026. The experiment will be removed after cycle 519, which is currently scheduled to end in December 2026.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Photoinhibition of comammox reaction in Nitrospira inopinata in a dose- and wavelength-dependent manner

Apparent contribution of complete ammonia-oxidizing organisms (comammox) to the global nitrogen cycle highlights the necessity for understanding niche differentiation of comammox bacteria among other ammonia oxidizers. While the high affinity for ammonia of the comammox species Nitrospira inopinata suggests their niche partitioning is expected to be centered in oligotrophic environments, their absence in nutrient-depleted environments (such as the oceans) suggests that other (abiotic) factors might control their distribution and spatial localization within microbial communities. Many ammonia- and nitrite-oxidizing organisms are sensitive to light; however, the photosensitivity of comammox has not been explored. Since comammox bacteria encode enzymatic machinery homologous to canonical ammonia-and nitrite-oxidizers, we hypothesized that comammox N. inopinata, the only available pure culture of this group of microorganisms, may be inhibited by illumination in a similar manner. We evaluated the impact of light intensity, wavelength, and duration on the degree of photoinhibition for cultures of the comammox species N. inopinata and the soil ammonia-oxidizing archaea Nitrososphaera viennensis. Both species were highly sensitive to light. Interestingly, mimicking diurnal light exposure caused an uncoupling of ammonia and nitrite oxidation in N. inopinata, indicating nitrite oxidation might be more sensitive to light exposure than ammonia oxidation. It is likely that light influences comammox spatial distribution in natural environments such as surface fresh waters according to diurnal cycles, light attenuation coefficients, and the light penetration depths. Our findings therefore provide ecophysiological insights for further studies on comammox both in field and laboratory settings.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1973

The measure of the moon.

Discussion of some of the procedures employed and results obtained in using photogrammetry in the Apollo lunar geology exploration program. The most modern approach to lunar photogrammetry came from orbit. The introduction into lunar orbit operations of precision metric and panorama cameras and laser altimeters provided the photographs and data through which many of the thitherto unsolvable local and lunar-wide control problems became amenable to solution. From the results obtained, there is shown to have emerged a described pattern of evolutionary sequence through which the moon has passed over the last 4.5 billion years.

Schmitt, H. H.↗
NASA NTRS1975

A 10.6 micron ladar for space rendezvous and docking

The paper describes a 10.6 micron ladar (a laser detection and ranging device) which is considered as a baseline sensor for space rendezvous and docking applications. The sensor uses a passively Q-switched CO2 laser as the transmitter active element, and a four-quadrant photodiode array, operated as a coherent receiver element in the heterodyne mode. The aperture will be about 3 inches, and the telescope will be able to steer the beam in a 40 by 40 degree window. Various aspects of the ladar system are examined in detail, including the laser control loop, the transmitter, the local oscillator, the telescope, and the output beam scanning.

Lowrey, D. O.↗
NASA NTRS1977

An image-processing system applied to earth-resource imagery

The Harwell Image Processing System (HIPS) has been adapted for processing earth-resource imagery in either film or tape format. Data from film are obtained using a computer-controlled flying-spot scanner. Local rapid interactive processing is based on a PDP 11/20 minicomputer which has suitable display facilities for immediate visual appraisal of results and also a fast data link to an IBM 370/168 computer complex. An extensive subroutine library is being assembled for data preprocessing and feature extraction. This chapter includes a discussion of the basic principles of image analysis, a description of the HIPS system, and finally, for illustrative purposes, a description of several simple software routines.

Carter, P.↗
NASA NTRS1980

USSAERO computer program development, versions B and C

Versions B and C of the unified subsonic and supersonic aerodynamic analysis program, USSAERO, are described. Version B incorporates a new symmetrical singularity method to provide improved surface pressure distributions on wings in subsonic flow. Version C extends the range of application of the program to include the analysis of multiple engine nacelles or finned external stores. In addition, nonlinear compressibility effects in high subsonic and supersonic flows are approximated using a correction based on the local Mach number at panel control points. Several examples are presented comparing the results of these programs with other panel methods and experimental data.

Woodward, F. A.↗
NASA NTRS1981

Process development for automated solar cell and module production. Task 4: Automated array assembly

The Unimate robot was programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. Mechanical construction of the Automated Lamination Station and Final Assembly Station were completed on schedule. All final wiring and interconnect cables were also completed and the first operational testing began. The final controlling program was written. A local fabricator was contracted to produce the glass reinforced concrete panels to be used for testing and deliverables. A video tape showing all three stations in operation was produced.

Hagerty, J. J.↗
NASA NTRS1983

Partitioning of large space structures vibration control computations

The vibration control of large space structures is studied. It is found to be computationally demanding. Distribution of the vibration control computations among central and local processors can significantly reduce the throughput required from the central processor and may also result in improved performance due to reduced transport lag.

Kernan, J.↗
NASA NTRS1984

SARSAT - Using space for the search and rescue of lives in distress

A major cooperative effort between west and east bloc nations in developing a new space system for detecting ships and aircraft in distress is discussed. The compatible working of the SARSAT system developed by Canada, France, and the US and the COSPAS system developed by the Soviet bloc is summarized, and the SARSAT system is described. The method of location determination is presented, and the ELT and EPIRB, space segment, local user terminal, and mission control center subsystems of the SARSAT system are surveyed, showing block diagrams and data on spacecraft orbital parameters and ELT/EPIRB BECON characteristics. The current problem of ground-based interference is discussed. An outline of future development activities leading to the implementation of a fully operational system is included.

Flatow, F.↗
NASA NTRS1985

Evidence of scattering effects on the sizes of interplanetary Type III radio bursts

An analysis is conducted of 162 interplanetary Type III radio bursts; some of these bursts have been observed in association with fast electrons and Langmuir wave events at 1 AU and, in addition, have been subjected to in situ plasma parameter measurements. It is noted that the sizes of burst sources are anomalously large, compared to what one would anticipate on the basis of the interplanetary plasma density distribution, and that the variation of source size with frequency, when compared with the plasma frequency variation measured in situ, implies that the source sizes expand with decreasing frequency to fill a cone whose apex is at the sun. It is also found that some local phenomenon near the earth controls the apparent size of low frequency Type III sources.

Steinberg, J. L.↗
NASA NTRS1987

Nonlinear input-output systems

Necessary and sufficient conditions that the nonlinear system dot-x = f(x) + ug(x) and y = h(x) be locally feedback equivalent to the controllable linear system dot-xi = A xi + bv and y = C xi having linear output are found. Only the single input and single output case is considered, however, the results generalize to multi-input and multi-output systems.

Hunt, L. R.↗
NASA NTRS1989

On principles, methods and recent advances in studies towards a GPS-based control system for geodesy and geodynamics

Although Very Long Baseline Interferometry (VLBI) and Satellite Laser Ranging (SLR) are becoming increasingly important tools for geodynamic studies, their future role may well be fulfilled by using alternative techniques such as those utilizing the signals from the Global Positioning System (GPS). GPS, without the full implementation of the system, already offers a favorable combination of cost and accuracy and has consistently demonstrated the capability to provide high precision densification control in the regional and local areas of the VLBI and SLR networks. This report reviews VLBI and SLR vis-a-vis GPS and outlines the capabilities and limitations of each technique and how their complementary application can be of benefit to geodetic and geodynamic operations. It demonstrates, albeit with a limited data set, that dual-frequency GPS observations and interferometric type analysis techniques make possible the modelling of the GPS orbits for several days with an accuracy of a few meters. The use of VLBI or SLR sites as fiducial stations together with refinements in the orbit determination procedures can greatly reduce the systematic errors in the GPS satellite orbits used to compute the positions of non-fiducial locations. In general, repeatability and comparison with VLBI of the GPS determined locations are of the order of between 2 parts in 10 to the 7th power and 5 parts in 10 to the 8th power for baseline lengths less than 2000 km. This report is mainly a synthesis of problems, assumptions, methods and recent advances in the studies towards the establishment of a GPS-based system for geodesy and geodynamics and is one phase in the continuing effort for the development of such a system. To some, including the author, it seems reasonable to expect within the next few years that more evidence will show GPS to be as a powerful and reliable a tool as mobile VLBI and SLR are today, but largely more economical.

Delikaraoglou, Demitris↗
NASA NTRS1990

The real-time learning mechanism of the Scientific Research Associates Advanced Robotic System (SRAARS)

Scientific research associates advanced robotic system (SRAARS) is an intelligent robotic system which has autonomous learning capability in geometric reasoning. The system is equipped with one global intelligence center (GIC) and eight local intelligence centers (LICs). It controls mainly sixteen links with fourteen active joints, which constitute two articulated arms, an extensible lower body, a vision system with two CCD cameras and a mobile base. The on-board knowledge-based system supports the learning controller with model representations of both the robot and the working environment. By consecutive verifying and planning procedures, hypothesis-and-test routines and learning-by-analogy paradigm, the system would autonomously build up its own understanding of the relationship between itself (i.e., the robot) and the focused environment for the purposes of collision avoidance, motion analysis and object manipulation. The intelligence of SRAARS presents a valuable technical advantage to implement robotic systems for space exploration and space station operations.

Chen, Alexander Y.↗
NASA NTRS1990

Time and frequency measuring metrological equipment in the USSR

The complex of the means of providing time and frequency traceability in the USSR includes the system of time and frequency standards of the National Time and Frequency Calibration Service, time and frequency transfer facilities and local time and frequency standards. Control on measurement correctness is performed by the All-Union State Standard calibration service. The hardware of most of the above-mentioned systems is provided by the instruments developed by our institute. A common scientific and technological approach allowed us to create a unified system of time-frequency equipment composed of widely used serial instruments, sets, automated systems and complexes. Primary frequency standards of different classes, time and frequency references and instruments are based on the unified system. CH1-70 hydrogen frequency standard and its CH1-70A, CH1-80 modifications are used in the group time and frequency standards. Measuring time and data processing techniques, and also instrumentation specifications on the results of 10-year operation are given. The existing system provides time-frequency measurements with 2 times 10(exp -13) plus or minus 1 times 10(exp -14) accuracy.

Uljanov, Adolph A.↗
NASA NTRS1992

Mixed-mode fracture in unidirectional graphite epoxy composite laminates with central notch

Mixed-mode matrix fracture in central notched off-axis unidirectional composite laminates was investigated. A limited number of unidirectional tensile type specimens with a central, horizontal, notch were tested. Crack initiation and propagation were examined under various local stress fields that were controlled by fiber orientations. The tested specimens were simulated using a two dimensional finite element method with constant strain loading. The strain energy release rates along the crack were evaluated via crack closure technique. The variation of critical strain energy rates with off-axis angle was studied. The results from single (one-sided) and double (two-sided) crack simulations were presented and compared.

Binienda, Wieslaw K.↗
NASA NTRS1992

Natural transition from rate to force control of a manipulator

A method for teleoperator control which offers advantages over previous techniques is demonstrated. In the new method, a fundamental variable exchanged between the master and slave is the rate of change in position and force. An inherent capability of the control scheme is demonstrated for transition between control methods based on environmental constraints in a manner natural to the operator. Specifically, rate control of a manipulator makes the transition to force-force control when a force-reflecting hand controller is used with a local force accommodation algorithm running on the remote manipulator. The transition from rate to force occurs when contact is made with the environment.

Harrison, F. W.↗
NASA NTRS1933

The D.V.L. Gliding-angle Control : W. Hubner Design

This report describes a device for arbitrary enlargement of the gliding angle of airplanes, especially of such with flat gliding angle and difficult landing characteristics. The D.V.L. gliding angle control (design, Hubner) permits a local interruption of the lift distribution along the span and consequently an increased induced drag. The mechanism comprises two wing rudders operated by lever from the pilot's cockpit. Said rudders are fitted on the top side of the wing near the leading edge. The displacement of these rudders results in a separation of the air flow on the top side of the wing.

Hubner, Walter↗
NASA NTRS1993

New developments in the method of space-time conservation element and solution element: Applications to the Euler and Navier-Stokes equations

A new numerical framework for solving conservation laws is being developed. This new approach differs substantially in both concept and methodology from the well-established methods--i.e., finite difference, finite volume, finite element, and spectral methods. It is conceptually simple and designed to avoid several key limitations to the above traditional methods. An explicit model scheme for solving a simple 1-D unsteady convection-diffusion equation is constructed and used to illuminate major differences between the current method and those mentioned above. Unexpectedly, its amplification factors for the pure convection and pure diffusion cases are identical to those of the Leapfrog and the DuFort-Frankel schemes, respectively. Also, this explicit scheme and its Navier-Stokes extension have the unusual property that their stabilities are limited only by the CFL condition. Moreover, despite the fact that it does not use any flux-limiter or slope-limiter, the Navier-Stokes solver is capable of generating highly accurate shock tube solutions with shock discontinuities being resolved within one mesh interval. An accurate Euler solver also is constructed through another extension. It has many unusual properties, e.g., numerical diffusion at all mesh points can be controlled by a set of local parameters.

Chang, Sin-Chung↗