Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

XPS analysis of the effect of fillers on PTFE transfer film development in sliding contacts

The development of transfer films atop steel counterfaces in contact with unfilled and bronze-filled PTFE has been studied using X-ray photoelectron spectroscopy. The sliding apparatus was contained within the vacuum of the analytical system, so the effects of the native oxide, hydrocarbon, and adsorbed gaseous surface layers of the steel upon the PTFE transfer behavior could be studied in situ. For both the filled and the unfilled PTFE, cleaner surfaces promoted greater amounts of transfer. Metal fluorides, which formed at the transfer film/counterface interface, were found solely in cases where the native oxide had been removed to expose the metallic surface prior to sliding. These fluorides also were found at clean metal/PTFE interfaces formed in the absence of frictional contact. A fraction of these fluorides resulted from irradiation damage inherent in XPS analysis. PTFE transfer films were found to build up with repeated sliding passes, by a process in which strands of transfer filled in the remaining counterface area. Under these reported test conditions, the transfer process is not expected to continue atop previously deposited transfer films. The bronze-filled composite generated greater amounts of transfer than the unfilled PTFE. The results are discussed relative to the observed increase in wear resistance imparted to PTFE by a broad range of inorganic fillers.

Blanchet, T. A.↗
NASA NTRS2003

Development of Advanced Thermal and Environmental Barrier Coatings Using a High-Heat-Flux Testing Approach

The development of low conductivity, robust thermal and environmental barrier coatings requires advanced testing techniques that can accurately and effectively evaluate coating thermal conductivity and cyclic resistance at very high surface temperatures (up to 1700 C) under large thermal gradients. In this study, a laser high-heat-flux test approach is established for evaluating advanced low conductivity, high temperature capability thermal and environmental barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) program. The test approach emphasizes the real-time monitoring and assessment of the coating thermal conductivity, which initially rises under the steady-state high temperature thermal gradient test due to coating sintering, and later drops under the cyclic thermal gradient test due to coating cracking/delamination. The coating system is then evaluated based on damage accumulation and failure after the combined steady-state and cyclic thermal gradient tests. The lattice and radiation thermal conductivity of advanced ceramic coatings can also be evaluated using laser heat-flux techniques. The external radiation resistance of the coating is assessed based on the measured specimen temperature response under a laser- heated intense radiation-flux source. The coating internal radiation contribution is investigated based on the measured apparent coating conductivity increases with the coating surface test temperature under large thermal gradient test conditions. Since an increased radiation contribution is observed at these very high surface test temperatures, by varying the laser heat-flux and coating average test temperature, the complex relation between the lattice and radiation conductivity as a function of surface and interface test temperature may be derived.

Zhu, Dongming↗
DOE OSTI2024

Investigation of Interlayer Dielectric in BaTiO 3 /III–Nitride Transistors

In this paper, the impact of varying the thickness of the Al 2 O 3 interlayer dielectric on the electrical characteristics of BaTiO 3 /III-nitride transistors is investigated. In the findings, it is revealed that a minimum thickness of 8 nm for the Al 2 O 3 layer is crucial to maintain high device performance and protect against sputtering-induced damage during BaTiO 3 deposition. The fabricated BaTiO 3 /Al 2 O 3 /AlGaN/GaN high electron mobility transistors exhibit exceptional electrical properties, including a maximum current density of 700 mA mm –1 , an on-resistance of 5 Ω mm, an I ON /I OFF ratio of 10 7 , a subthreshold slope of 119 mV dec –1 , and significantly reduced gate leakage current. The devices with the optimal 8 nm Al 2 O 3 thickness demonstrates excellent agreement between theoretical and experimental values for effective mobility, achieving a value of 1188 cm 2 V –1 ·s at a 2D electron gas density of 10 13 cm –2 . Furthermore, in the study, it is confirmed that increasing the Al 2 O 3 thickness also improves the quality of interface charge density, as evidenced by the results obtained from capacitance–voltage measurements. In these findings, the critical role of controlling the Al 2 O 3 thickness in optimizing the electrical characteristics and overall performance of BaTiO 3 /III-nitride transistors are highlighted.

42 ENGINEERING↗
DOE OSTI2025

Origin of large variations of current on/off ratio and switching voltage in atomically thin memristors: an exascale ab initio transport study

Nonvolatile resistive switching in two-dimensional monolayers opens a new avenue for high-density memory/computing devices. However, questions remain as to why the current on/off ratio and switching voltage vary significantly among different devices. Here, we simulate electronic transport of large systems consisting of a h-BN monolayer sandwiched by gold electrodes, enabled by an implementation of the nonequilibrium Green’s function method in the exascale density functional theory (DFT) code: Real-space MultiGrid. Systematic calculations reveal that the wide range of on/off ratios is due to variations in interface distances between the electrode and h-BN that significantly modulate their wavefunction overlap. In addition, DFT calculations demonstrate that the energy barrier of a gold atom dissociating from the electrode to h-BN increases dramatically with the interface distance, thereby explaining the strong dependence of the switching voltage on distance. Our work demonstrates the significance of interface distance in governing the current on/off ratio and switching voltage.

Electronic devices↗
DOE OSTI2020

NMDQi Thermal-hydraulic Optimization, Analysis, and Scoping Tool (TOAST)

The Thermal-hydraulic Optimization, Analysis, and Scoping Tool (TOAST) is developed to support the thermal-hydraulic aspects for the design of optimal irradiation vehicles for the Nuclear Materials Discovery and Qualification initiative (NMDQi). TOAST is currently a MATLAB-based tool that utilizes a simplified steady-state analytical model where a radial thermal resistance circuit is utilized to account for conduction through up to 2 capsules, a gas gap, a thermal bond, a sample cladding, and a sample, as well as the convection from a water coolant outside the capsules. The geometry is discretized axially along the user-defined height of a basket with a user-defined number of points/nodes, essentially turning TOAST into a semi-2D heat transfer analysis utility for cylindrical irradiation vehicles with practically any configuration, solving for temperatures radially at multiple axial locations. TOAST utilizes a Graphical User Interface (GUI) in-which a user can define the geometrical layout, the materials utilized for each component, the coolant characteristics, and the required solution. The user can define the geometry by inputting the diameters, thicknesses, and heights for each component, whereas the materials are defined via the user-provided constant or variable thermal conductivities. The user can select the coolant's inlet temperature, pressure, and the pressure drop across the height of the problem (which is used to calculate the velocity of the flow). Finally, the user can choose to solve for a sample heat generation rate limit by inputting temperature limits for the sample and capsules or can choose to purely solve for the axial temperature distributions of each component by inputting a pre-selected heat generation rate. Either way, TOAST provides the user with axial temperature distributions of all the components including the coolant, and the heat generation rate limit as well as the maximum outlet coolant temperature. The user can also choose to do one of 6 sensitivity analyses in TOAST. The sensitivity analyses yield plots of the sensitivity of the heat generation rate limit, the maximum coolant temperature, and the pressure limit for the annular components due to perturbations in 1-2 unknown variables based on the selected sensitivity analysis. Benchmarks between computations in TOAST and equivalent 2D axis symmetric ABAQUS models are presented, showing that TOAST results are within less than 3% of ABAQUS results in most cases, and a maximum of 8% difference in some cases. The benchmarks also revealed that this uncertainty is tied to the selection of an appropriate Nusselt number correlation and appropriate thermal conductivities, which the user can do from the GUI. Regardless, TOAST is demonstrated as a computationally efficient, highly accessible, and accurate utility for optimization and scoping s of studies different irradiation vehicles.

42 ENGINEERING↗
NASA NTRS1982

Preliminary results on the abradability of porous, sintered seal material

Preliminary results are presented for the case of titanium blade specimens, with bare tips (or covered with wear resistant, plasma sprayed materials) rubbing at 100 m/s against specimens of abradable nickel-chromium seal material moving toward the rotating blades at 0.0125 mm/s or at 0.025 mm/s. Using a two component dynamometer, the normal force of the rub interaction was measured and the shear component estimated. The elastoplastic properties of the seal material have been determined and those parameters as well as the rigidity of the rub tester system are considered in conjunction with those affecting the accuracy of the measurement of the forces arising at the blade-seal interface. The average and the 'local instantaneous' temperatures of the seal specimen and the temperature of the blade tip surface during rubbing are presented as functions of time. A seal densification factor is defined and its functional relationships with contact force components, temperature, wear ratio and blade tip abrading capability are indicated.

Wolak, J.↗
DOE OSTI2025

Status Report on the Development of Cladding Inner-wall and Outer-wall Coatings

Advanced cladding is critical for nuclear reactors with enhanced performance in radiation tolerance, neutron transparency and reactor safety. Using advanced cladding will ensure the adequate thermal conductivity and mechanical stability of the cladding base material, corrosion resistance and high-temperature coolant compatibility of the cladding surface, and chemical stability in the cladding inner wall against fuel cladding chemical interaction (FCCI). An innovative cladding with a three-layer structure (i.e., a modified outer surface, a robust clad base material, and a modified inner wall) promises to meet all these requirements. In this status report, the initial efforts on the development of cladding inner-wall and outer-wall coatings are summarized. The activities covered in this report are (1) High-resolution TEM studies of TiN/HT-9 interface atomic structure and chemistry after ion irradiation, (2) High-resolution TEM studies of TiN/14YWT ODS interface atomic structure after thermal cycling, (3) Inner-wall TiN coating for an experimental 14YWT ODS cladding, and (4) Corrosion test of TiN coated Ziracloy-4 bar samples.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Deciphering Chemical/Electrochemical Compatibility of Li 3 InCl 6 in 5.2 V High-Voltage LiCoO 2 All-Solid-State Batteries

Large interfacial resistance is a widely recognized impediment to the advancement of high-voltage, all-solid-state batteries. However, a comprehensive understanding of the fundamental cause behind the interfacial resistance between solid electrolytes and typical layered oxide cathodes has not yet been achieved. Here, we investigated the high-voltage stability of Li 3 InCl 6 and elucidated the underlying interfacial electrochemical reactions between LiCoO 2 and Li 3 InCl 6 . Further, the pairing of Li 3 InCl 6 with LiCoO 2 exhibited a superior capacity retention of 73.6% even at 5.2 V, much higher than 28.2% charged at 4.6 V in lithium-ion batteries after 70 cycles. The enhanced high-voltage stability of ASSBs is attributed to the stable interface formed between LiCoO 2 and Li 3 InCl 6 and the reinforced surface and bulk structure stability. On the other hand, the ultrahigh voltage still causes the partial decomposition of Li 3 InCl 6 and generates interfacial compounds such as InClO and cobalt and indium chlorides/oxides.

25 ENERGY STORAGE↗
DOE OSTI2020

Air-Stable Calcium Cyanamide-Supported Ruthenium Catalyst for Ammonia Synthesis and Decomposition

Efficient ammonia synthesis and decomposition processes under mild conditions are important to meet the expanding demand in major applications of ammonia as the energy carrier and to provide feedstock for chemical industry. In this study, we report that air-stable calcium cyanamide-supported ruthenium (Ru/CaCN 2 ) works as an efficient and stable catalyst for ammonia synthesis and decomposition. Ru/CaCN 2 exhibits greater catalytic performances for both reactions than Ru/Ca 2 N electride and Ru–Cs/MgO. The kinetic analysis for ammonia synthesis suggests that Ru/CaCN 2 exhibits low apparent activation energy and high resistance to hydrogen poisoning, which has characteristics similar to the kinetic parameters of Ru-supported electride catalyst. H 2 -temperature programmed reaction and temperature programmed desorption revealed that Ru promoted the formation of CN 2 vacancies on the CaCN 2 surface which in turn capture hydrogen as H – ions during the reaction. Density functional theory calculations provide insights into how the formation of CN 2 vacancies is promoted by Ru, which leads to the decrease in the work function of the CaCN 2 surface and the hydrogen capture at the Ru-support interface. These results suggest that the high catalytic performance of Ru/CaCN 2 can be attributed to the formation of a quasi-electride structure at the Ru–CaCN 2 interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2022

Simulation-based Study of Single-Event Burnout in 4H-SiC High-Voltage Vertical Superjunction DMOSFET: Physical Failure Mechanism and Robustness vs. Performance Tradeoffs

We explore and elucidate physical failure mechanisms in a 4H-SiC, high voltage, superjunction (SJ) vertical DMOSFET from a single heavy ion strike using three-dimensional electro-thermal transient simulations. The single-event burnout (SEB) failure is thermal runaway from second breakdown, initiated by impact ionization and terminated with mesoplasma formation, at the center of the P-pillar/N+ substrate interface. We also demonstrate that the SEB performance of this SiC SJ DMOSFET is insensitive to the pillar width but sensitive to the strike location with ion strike at the P-pillar causing SEB at a lower blocking voltage than at the N-pillar. Compared to commercially available 1.2 kV blocking-rated non-SJ DMOSFETs, which have been demonstrated to survive SEB up to 525 V, the SJ DMOSFET increases SEB survival threshold voltage (VSEB) by a factor of 2.2, making it close to 1200 V, while the on-resistance is increased by only 11%. Using our recently developed figure of merit (FoM), which considers the trade-off between VSEB and on-state performance, we find that the SiC SJ DMOSFET achieves a FoM that is 14 times better, making it superior to conventional 1.2 kV SiC DMOSFETs for long-term radiation-tolerant operation in space applications.

Silicon Carbide↗
DOE OSTI2022

Composite Solid Ion Conductor with Engineered Lithium Interface

Successful widespread commercialization of electric vehicles is contingent upon development of safe high energy density batteries capable of long cycle life. Lithium metal affords the highest theoretical capacity (3,860 mAh/g) and lowest electrochemical potential (-3.04V vs SHE), which offers the highest specific energy density of anode materials today. While Li-ion batteries are capable of delivering energy densities of 400-600 Wh/kg, the development of lithium metal batteries such as Li-S and Li-air may boost this number up to 650 and 950 Wh/kg, respectively. However, significant progress towards the passivation of lithium metal must occur before the energy density benefit can be realized. Issues with lithium dendrite formation, anode volume expansion, and continuous solid electrolyte interphase (SEI) build-up often result in significant safety concerns, high cell resistance, and poor cycle life. The intrinsic high reactivity between lithium metal with conventional lithium ion electrolytes (organic carbonate-based solvents) makes it extremely difficult to overcome these problems. In this project, Wildcat performed focused, fundamental research and development on composite polymer/ceramic electrolytes and protected lithium metal anodes to develop an all solid state lithium metal battery targeting the DOE requirements to enable commercialization. Wildcat successfully leveraged its high throughput battery platform and explored a broad composite electrolyte compositional space. Additionally, Wildcat screened large numbers of inorganic and organic coatings for lithium metal protection using in situ liquid methods and translated the best results to all solid cells. The proposed composite polymer/ceramic electrolyte and a protected lithium metal anode enabled a solid-state lithium metal battery. The ultimate targets from this effort will deliver a safe all solid-state lithium metal pouch cell with over 350 Wh/kg and over 1,000 cycles (C/3) with the cost estimate below $100/kWh. During the course of the project, we demonstrated stable cycling of 10’s of cycles with the composite SSE and our protected lithium. The work has continued after the conclusion of the DOE funding, demonstrating further improvements in catholyte composition and thinner composite solid electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2026

First Solar Thermal Energy Planner (STEP 1) and Nationwide Industrial Heat and Power Analysis

The First Solar Thermal Energy Planner (STEP 1) and Nationwide Industrial Heat and Power Analysis (aka the STEP 1 Project or the Project) aimed to (1) developed a brand-new web tool that could provide decision support through free, rapid techno-economic analysis of behind-the-meter solar+storage systems for industrial process heat and (2) conduct high-level analyses of the cost-competitiveness of the same systems across the US in key sectors. The STEP 1 web tool collects key location, land availability, thermal load profile, proccess heat temperature and media, and other key parameters through an easy-to-use user interface (UI). The UI was designed to meet the user at their level of understanding by minimizing the number of required inputs as much as possible while including options for more nuanced inputs if the user desires. STEP 1 advises users on which solar thermal tehcnologies that could fit their needs based on the inputs provided (namely process media and temperature). The tool can model a wide range of solar thermal technologies including flat plate collectors, evacuated tubes, parabolic troughs, linear Fresnel, and molten salt towers all with corresponding thermal energy storage (TES) - solar PV with resistive heating and TES is also included. Once the parameters are collected, a nominal thermal energy production profile for the facility's location is generated using NREL's System Advisory Model (SAM) and then passed to a modified version of NREL's REopt platform to optimize the size (capacity) and dispatch of the solar+storage system to minimize lifecycle costs subject to energy balance, fuel and electricity rates, emission reductions goals, and other constraints. This entire process takes less than 20 minutes, is completely free, requires zero coding skills, and provides the user with a high-level assessment on the techno-economic feasability of deploying solar+storage systems for their energy needs. In addition to the development of the STEP 1 web tool, the project completed two complementary analyses focused on leveraging the backend code of STEP 1, public industrial facility locations and fuel consumption data, and key sector information to assess the economic opportunity of reducing fuel costs at various levels of capacity factor around the US. Both analyses found that there are key markets, locations, industrial sectors (namely food and beverage), and degrees of offset where solar thermal technologies could be cost-effectively deployed, highlighting a key market entry point for these technologies, and assessing deployment potential. In summary, the STEP 1 project improved the opportunities for solar+storage systems to expand into the industrial process heat market through breaking down barriers to assessing these technologies.

14 SOLAR ENERGY↗
NASA NTRS2012

Electrospun Nanofiber Coating of Fiber Materials: A Composite Toughening Approach

Textile-based composites could significantly benefit from local toughening using nanofiber coatings. Nanofibers, thermoplastic or otherwise, can be applied to the surface of the fiber tow bundle, achieving toughening of the fiber tow contact surfaces, resulting in tougher and more damage-resistant/tolerant composite structures. The same technique could also be applied to other technologies such as tape laying, fiber placement, or filament winding operations. Other modifications to the composite properties such as thermal and electrical conductivity could be made through selection of appropriate nanofiber material. Control of the needle electric potential, precursor solution, ambient temperature, ambient humidity, airflow, etc., are used to vary the diameter and nanofiber coating morphology as needed. This method produces a product with a toughening agent applied to the fiber tow or other continuous composite precursor material where it is needed (at interfaces and boundaries) without interfering with other composite processing characteristics.

Kohlman, Lee W.↗
NASA NTRS1983

Chemical bonding technology for terrestrial photovoltaic modules

Encapsulated photovoltaic modules must hold together for 20 years, reliably resisting delamination and separation of any of the component materials. Delamination of encapsulation materials from each other, or from solar cells and interconnects, can create voids for accumulation of water, promoting corrosive failure. Delamination of silicone elastomers from unprimed surfaces was a common occurrence with early modules, but the incidences of silicone delamination with later modules decreased when adhesion promoters recommended by silicone manufacturers were used. An investigation of silicone delamination from unprimed surfaces successfully identified the mechanism, which was related to atmospheric oxygen and moisture. This early finding indicated that reliance on physical bonding of encapsulation interfaces for long life in an outdoor environment would be risky. For long outdoor life, the material components of a module must therefore be held together by weather-stable adhesion promoters that desirably form strong, interfacial chemical bonds.

Coulter, D. R.↗
NASA NTRSDate not supplied

Joining, Disassembly, and Reconfiguration of Thermoplastic Composites for Space Applications

Thermoplastic composites are increasingly being investigated for aerospace applications because of their relatively short processing time, good chemical and radiation resistance, and potential for reforming and reuse via melting. The manufacturing, reforming, and reuse of thermoplastic composites can be leveraged to advance joining, disassembly, and reassembly of structures for space exploration activities. Potential applications include, but are not limited to, habitats and on-orbit assembly and reassembly of large-scale truss structures. This work focuses on demonstrating the feasibility of joining, disassembly, and reassembly of a thermoplastic bond using heat and pressure. Polyether ether ketone (PEEK) composite adherends were joined using low-melt polyaryl ether ketone (LM-PAEK) thermoplastic films at the bonding interface. The single lap shear specimens with LM-PAEK film were tested and had a maximum shear strength between 5 and 8 MPa and consistently failed adhesively at the bondline. Reassembly of disassembled specimens was successfully demonstrated using additional thermoplastic interlayers. Thus, the reassembly of thermoplastic composite joints was found to be feasible. However, additional work is required to reduce film flowout and optimize consolidation parameters for an in space environment.

thermoplastic composites↗
DOE OSTI2023

Andreev reflection between aluminum and graphene across van der Waals barriers

We present planar aluminum superconductor–graphene junctions whose hybrid interface is engineered for couplings ranging from tunneling to the strongly coupled regime by employing an atomically thin van der Waals tunneling barrier. Without the vdW barrier, we find Al makes strongly coupled contacts with the fully proximities graphene channel underneath. Using a large band gap hexagonal boron nitride (hBN) barrier, we find the junctions always remain in the weak coupling regime, exhibiting tunneling characteristics. Using monolayer semi-conducting transition metal dichalcogenides (TMDs) such as MoS2, we realize intermediate coupling with enhanced junction conductance due to the Andreev process. In this intermediate regime, we find that junction resistance changes in discrete steps when sweeping a perpendicular magnetic field. The period of the resistance steps in the magnetic field is inversely proportional to the junction area, suggesting the physical origin of our observations is due to magnetic-field-induced vortex formation in the planar junction.

Physics↗
DOE OSTI2021

A KBase Case Study on Genome-wide Transcriptomics and Plant Primary Metabolism in Sorghum

A better understanding of the genetic and metabolic mechanisms that confer stress resistance and tolerance in plants is key to engineering new crops through advanced breeding technologies. This requires a systems biology approach that builds on a genome-wide understanding of the regulation of gene expression, plant metabolism, physiology and growth. In this study, we examine the response to drought stress in Sorghum, as we leverage the tools for transcriptomics and plant metabolic modeling we have implemented at the U.S. Department of Energy Systems Biology Knowledgebase (KBase). KBase enables researchers worldwide to collaborate and advance research by allowing them to upload private or public data into the KBase Narrative Interface, empowering them to analyze this data using a rich, extensible array of computational and data-analytics tools, and allows them to securely share scientific workflows and conclusions. We demonstrate how to use the current RNA-seq tools in KBase, applicable to both plants and microbes, to assemble and quantify long transcripts and identify differentially expressed genes effectively. More specifically, we demonstrate the utility of the platform by identifying key genes that are differentially expressed during drought-stress in Sorghum bicolor, which is an important sustainable production crop plant. We then show how to use KBase tools to predict the membership of genes in metabolic pathways and examine expression data in the context of metabolic subsystems. We demonstrate the power of the platform by making the data analysis and interpretation available to the biologists in the reproducible, re-usable, point-and-click format of a KBase Narrative thus promoting FAIR (Findable, Accessible, Interoperable and Reusable) guiding principles for scientific data management and stewardship.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1991

Frequency-dependent characteristics and trap studies of lattice-matched (x = 0.53) and strained (x greater than 0.53) In(0.52)Al(0.48)As/In(x)Ga(1-x)As HEMT's

The low-frequency characteristics of InAlAs/In(x)Ga(1-x)As high-electron-mobility transistors (HEMTs) are studied, and trap densities are evaluated. The HEMTs' transconductance g(m) and output resistance R(ds) dispersion are smallest for 60 percent indium (In) content and largest for 53 percent In. The maximum dispersion for the 53 percent In sample is about 6 percent for g(m) and about 13.3 percent for R(ds), corresponding to lower values than observed in MESFETs. The R(ds) dispersion characteristics are weaker than in AlGaAs/GaAs HEMTs and manifest themselves primarily up to 100 kHz. An analysis of the dispersion results indicates that, unlike in the case of MESFETs, the channel region under the gate rather than the access regions is responsible for the dispersion. Interface state densities were extracted by the AC conductance method and were found to follow the same trend as the g(m) and R(ds) dispersion.

Ng, Geok-Ing↗