Results for “hardware efficiency” — Page 52

DOE OSTI2023

Performance assessment of a real water source heat pump within a hardware-in-the-loop (HIL) testing environment

Over the last decade, the global fight against climate change through electrification has led to an increase in research on building heating, ventilation, and air conditioning (HVAC) systems that utilize intelligent control algorithms to provide demand-side grid service while also maintaining the thermal comfort of building occupants. As the pivotal point between building electricity consumption and indoor thermal comfort, high-efficiency electrical vapor-compression heat pumps are at the center of these emerging studies, and various grid-interactive and occupant-comfort control algorithms have been developed for them. The impact of these algorithms on heat pump operation and performance when subjected to different weather conditions, building loads, and grid requests calls for investigation and verification via experimental testing with actual heat pumps integrated with real-time building and grid responses. This study introduces a Water-Source Heat Pump (WSHP) Hardware-in-The-Loop (HIL) Test Facility that is the first of its kind. This testbed utilizes a 2-ton variable speed water-to-air heat pump that is capable of interacting with a virtual environment currently comprised of an EnergyPlus (E+) building simulation, an agent-based occupant behavioral model, and a single U-tube ground-loop heat exchanger (GLHE) model. Detailed descriptions of the testbed’s physical design and operation, virtual environment, as well as their mutual communication is provided. An uncertainty analysis is also performed under manufacturer specified heating and cooling design conditions. This analysis shows that the total load across the WSHP’s demand side heat exchanger, i.e., the sum of its latent and sensible components, can be measured with a relative uncertainty of ± 10.4% and ± 3.6% in cooling and heating mode respectively. The WSHP’s coefficient of performance (COP) can be measured with relative uncertainties of ± 10.4% in cooling mode, and ± 3.7% in heating mode. A preliminary 24-h experimental demonstration is then performed utilizing the DOE prototype small commercial office building model in E+. The simulation takes place in Atlanta, GA on the date of 08/26/15 from 12:00 AM to 11:59 PM using TMY3 weather data. Here, the results from this demonstration show that over the course of this experiment the simulated outputs of zone dry-bulb temperature, zone humidity ratio, and WSHP inlet water temperature can be tracked by testbed emulators up to a root mean squared error (RMSE) of ± 0.27 °C, ± 0.376 g/kg, and ± 0.85 °C respectively. The WSHP’s dynamic behavioral characteristics and performance are also captured, and correspond well with the authors’ previous understanding of heat pump efficiency as a function of evaporator and condenser fluid inlet conditions respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS2014

Control and Non-Payload Communications Generation 1 Prototype Radio Flight Test Report

Unmanned aircraft (UA) represent a new capability that will provide a variety of services in the Government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized because of the lack of a common understanding of what is required to safely operate Unmanned Aircraft Systems in the National Airspace System (UAS in the NAS). The desire and ability to fly UA is of increasing urgency. The application of UA to perform national security, defense, scientific, and emergency management are driving the critical need for less restrictive access by UA to the NAS. Existing Federal Aviation Regulations, procedures, and technologies do not allow routine UA access to the NAS. Access to the NAS is hampered by challenges such as the lack of an onboard pilot to see and avoid other aircraft; the ability of a single pilot or operator to control multiple UA; the reliance on command and control (C2) links; the altitudes, speeds, and duration at which the aircraft fly; and the wide variation in UA size and performance. NASA is working with other Government agencies to provide solutions that reduce technical barriers and make access to the NAS routine. This goal will be accomplished through system-level integration of key concepts, technologies, or procedures and through demonstrations of these integrated capabilities in an operationally relevant environment. This project provides an opportunity to transition the acquired empirical data and knowledge to the Federal Aviation Administration and other stakeholders to help them define the requirements for routine UA access to the NAS.Radio communications channels for UA are currently managed through exceptions and use either Department of Defense frequencies for line-of-sight (LOS) and satellite-based communications links, low-power LOS links in amateur bands, or unlicensed Industrial/Scientific/Medical (ISM) frequencies. None of these frequency bands are designated for safety and regularity of flight. Only recently has radiofrequency (RF) spectrum been allocated by the International Telecommunications Union specifically for commercial UA C2, LOS communication (L-Band: 960 to 1164 MHz, and C-Band: 5030 to 5091 MHz). The safe and efficient integration of UA into the NAS requires the use of protected RF spectrum allocations and a new data communications system that is both secure and scalable to accommodate the potential growth of these new aircraft. Data communications for UA-referred to as control and non-payload communications (CNPC)-will be used to exchange information between a UA and a ground station (GS) to ensure safe, reliable, and effective UA flight operation. The focus of this effort is on validating and allocating new RF spectrum and data link communications to enable civil UA integration into the NAS. Through a cost-sharing cooperative agreement with Rockwell Collins, Inc., the NASA Glenn Research Center is exploring and performing the necessary development steps to realize a prototype UA CNPC system. These activities include investigating signal waveforms and access techniques, developing representative CNPC radio hardware, and executing relevant testing and validation activities. There is no intent to manufacture the CNPC end product, rather the goals are to study, demonstrate, and validate a typical CNPC system that will allow safe and efficient communications within the L-Band and C-Band spectrum allocations. The system is addressing initial "seed" requirements from RTCA, Inc., Special Committee 203 (SC-203) and is on a path to Federal Aviation Administration certification. This report provides results from the flight testing campaign of the Rockwell Collins Generation 1 prototype radio, referred hereafter as the "radio." The radio sets operate within the 960- to 977-MHz frequency band with both air and ground radios using identical hardware. Flight tests involved one aircraft and one GS. Results include discussion of aircraft flight paths and associated radio performance.

Shalkhauser, Kurt A.↗

NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

vaned diffuser↗

NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

centrifugal compressor↗

DOE OSTI2023

Quantum simulations of SO(5) many-fermion systems using qudits

The structure and dynamics of many-body systems are the result of a delicate interplay between underlying interactions. Fermionic pairing, for example, plays a central role in various physical systems, ranging from condensed matter to nuclear systems, where it can lead to collective phenomena such as superconductivity and superfluidity. In atomic nuclei, the interplay between pairing and particle-hole interactions leads to a high degree of complexity and intricate entanglement structures. Despite this apparent complexity, symmetries emerge and manifest themselves in observable regular patterns. These symmetries and their breakings have long been used to determine relevant degrees of freedom and simplify classical descriptions of many-body systems. Here, this work explores the potential utility of quantum computers with arrays of qudits in simulating interacting fermionic systems, when the qudits can naturally map the relevant degrees of freedom determined by an underlying symmetry group. The Agassi model of fermions interacting via particle-hole and pairing interactions is based on an underlying so(5) algebra. Such systems can intuitively be partitioned into pairs of modes with five basis states, which thus naturally map to arrays of d = 5 qudits (qu5its). Classical noiseless simulations of the time evolution of systems with up to twelve qu5its are performed, by implementing quantum circuits that are developed herein, using PYTHON codes invoking Google's CIRQ software. The resource requirements of the qu5it circuits are analyzed and compared with two different mappings to qubit systems: a physics-aware Jordan-Wigner mapping requiring four qubits per mode pair and a state-to-state mapping requiring three qubits per mode pair. While the dimensionality of Hilbert spaces in mappings to qu5it systems are less than those for the corresponding qubit systems, the number of entangling operations, depending on the available hardware, can either be greater or smaller than for the physics-aware Jordan-Wigner mapping. The state-to-state mapping, while having a smaller Hilbert space than Jordan-Wigner mappings, appears to be the least efficient in gate counts. Further, a previously unknown sign problem has been identified from Trotterization errors in time evolving high-energy excitations. There appear to be advantages in employing quantum computers with arrays of qudits to perform simulations of many-body dynamics that exploit the role of underlying symmetries, specifically in lowering the required quantum resources and in reducing anticipated errors that take the simulation out of the physical space. If the necessary entangling gates are not directly supported by the hardware, physics-aware mappings to qubits may, however, be advantageous for other aspects.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS2019

Fracture Control for Additively Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

NASA NTRS2019

Fracture Control for Additive Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

DOE OSTI2024

Modeling and Power-Hardware-in-the-Loop Validation of Synchronous Wind: An Inverterless Grid-Forming Wind Power Plant: Preprint

Grid-forming (GFM) control of Type-3 and Type-4 wind turbine generators has attracted substantial attention in power systems research; however, the limited over-current capability of power electronics converters continues to deteriorate the grid strength of the evolving power systems. Synchronous wind, also known as Type-5 wind turbine generator (WTG), offers a unique GFM solution to address grid integration and grid strength issues by keeping the grid largely synchronous at very high penetration levels of renewable generation. A Type-5 WTG interfaces to the electric grid via a synchronous generator (SG) driven by a variable-speed hydraulic torque converter; hence, the wind rotor operates in variable-speed mode for maximum power generation and the generator shaft remains synchronous to the grid. This paper developed and tested a high-fidelity model of Type-5 WTG under power-hardware-in-the-loop (PHIL) testing environment. The PHIL demonstration showed that a Type-5 WTGs inherently behaves as a GFM unit and can obtain similar performance in terms of power responses, wind rotor dynamics, and efficiency compared to Type-3 WTG in high wind conditions. The developed model also provides further insight on how Type-5 WTGs can benefit the smooth transition to power systems with high integration level of inverter-based resources.

grid strength↗

DOE OSTI2021

GPU acceleration of rank-reduced coupled-cluster singles and doubles

Here, we have developed a graphical processing unit (GPU) accelerated implementation of our recently introduced rank-reduced coupled-cluster singles and doubles (RR-CCSD) method. RR-CCSD introduces a low-rank approximation of the doubles amplitudes. This is combined with a low-rank approximation of the electron repulsion integrals via Cholesky decomposition. The result of these two low-rank approximations is the replacement of the usual fourth-order CCSD tensors with products of second- and third-order tensors. In our implementation, only a single fourth-order tensor must be constructed as an intermediate during the solution of the amplitude equations. Owing in large part to the compression of the doubles amplitudes, the GPU-accelerated implementation shows excellent parallel efficiency (95% on eight GPUs). Our implementation can solve the RR-CCSD equations for up to 400 electrons and 1550 basis functions—roughly 50% larger than the largest canonical CCSD computations that have been performed on any hardware. In addition to increased scalability, the RR-CCSD computations are faster than the corresponding CCSD computations for all but the smallest molecules. We test the accuracy of RR-CCSD for a variety of chemical systems including up to 1000 basis functions and determine that accuracy to better than 0.1% error in the correlation energy can be achieved with roughly 95% compression of the ov space for the largest systems considered. We also demonstrate that conformational energies can be predicted to be within 0.1 kcal mol -1 with efficient compression applied to the wavefunction. Finally, we find that low-rank approximations of the CCSD doubles amplitudes used in the similarity transformation of the Hamiltonian prior to a conventional equation-of-motion CCSD computation will not introduce significant errors (on the order of a few hundredths of an electronvolt) into the resulting excitation energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Modeling and Power-Hardware-in-the-Loop Validation of Synchronous Wind: An Inverterless Grid-Forming Wind Power Plant

Grid-forming (GFM) control of Type-3 and Type-4 wind turbine generators (WTGs) has attracted substantial attention in power systems research; however, the limited overcurrent capability of power electronics converters continues to deteriorate the grid strength of the evolving power systems. Synchronous wind, also known as a Type-5 WTG, offers a unique GFM solution to address grid integration and grid strength issues by keeping the grid largely synchronous at very high integration levels of renewable generation. A Type-5 WTG interfaces with the electric grid via a synchronous generator driven by a variable-speed hydraulic torque converter; hence, the wind rotor operates in variable-speed mode for maximum power generation, and the generator shaft remains synchronous to the grid. This paper develops and tests a high-fidelity model of a Type-5 WTG in a power-hardware-in-the-loop (PHIL) testing environment. The PHIL demonstration shows that a Type-5 WTG inherently behaves as a GFM unit and can obtain similar performance in terms of power responses, wind rotor dynamics, and efficiency compared to a Type-3 WTG in high-wind conditions. The developed model provides further insight into how Type-5 WTGs can benefit the smooth transition to power systems with high integration levels of inverter-based resources.

grid strength↗

DOE OSTI2023

Validation of Microgrid Algorithms using At-Scale Simulation and Emulation Real-Time (ASSERT) Framework

This paper presents a novel framework for validating microgrid algorithms using a At-Scale Simulation and Emulation Real-Time (ASSERT) setup. The proposed universal microgrid validation framework was developed at Advanced Research on Integrated Energy Systems (ARIES) platform at National Renewable Energy Laboratory in Golden, Colorado, USA. As the number of intercommunicating devices grow in power systems, along with more integration of inverter-based resources, developing and validating microgrid operation and control algorithms is becoming complex and time-consuming task. The ASSERT framework is designed to provide a comprehensive, accurate, and efficient solution for validating microgrid algorithms. It combines at-scale simulations and real-time emulation to create a virtual environment that closely mimics the behavior of a physical microgrids which are characteristic of future smart distribution systems, such as: (1) increasing variability in the physical size of new energy technologies; (2) requiring control large numbers of interconnected devices, and (3) integrating diverse technologies that have not previously worked together. The paper describes the technical details of the ASSERT framework, its validation process, and its benefits over traditional validation methods. The framework's ability to validate the performance of various algorithms is demonstrated through a case study, which shows that it can effectively identify the weaknesses of an algorithm and optimize its performance. Overall, the ASSERT framework is a promising tool that can significantly enhance the development and validation of microgrid algorithms, leading to more reliable and efficient microgrid operation.

at-scale↗

DOE OSTI2024

Toward Automated Detection of Portability Bugs in Kokkos Parallel Programs

Performance-portable programming frameworks provide abstractions for parallel execution to allow easily porting an application to multiple backend programming models, such as CUDA, HIP, and OpenMP. However, programs may still have portability bugs that manifest only on specific backends. Traditional testing is ineffective in discovering these bugs, as it would require concrete execution on all supported hardware configurations for a potentially infinite set of inputs. To mitigate this issue, we focused on a specific programming framework, Kokkos, and identified several categories of common portability bugs. We then developed Klokkos, a static analysis approach based on symbolic execution that can run on commodity hardware, before execution on supercomputers. As a proof-of-concept, we ran Klokkos on examples encoding the identified bugs. Our results show that Klokkos is effective, efficient, and precise: it detected all the considered bugs, quickly, and without any false positives. Although preliminary, our results motivate further research and development in this direction.

Kale, Vivek↗

DOE OSTI2024

A Neural Network-Based Power Mismatch Elimination Strategy for Integrated Solar and ESS AC/DC Systems (MARS)

The multiport autonomous reconfigurable solar power plant (MARS) is a promising concept for the integration of photovoltaic (PV) and energy storage system (ESS) to the transmission ac grid and a high-voltage direct current (HVdc) link. The presence of PV and ESS in each arm of the MARS results in uneven distribution of active power among different submodules (SMs), thereby leading to unbalanced SM capacitor voltages and potentially compromising the system stability. Moreover, in the case of partial shadings, shaded PV SMs will suffer from decreased power injections causing power mismatch in the MARS system. To address this issue, a neural-network-based power mismatch elimination (NNPME) strategy is proposed in this article. The proposed NNPME strategy optimizes ESS usage and leverages both dc and ac circulating currents to facilitate power transfer among the SMs, arms, and phases of the MARS system. Simulation and control hardware-in-the-loop (cHIL) experiments demonstrate the effectiveness of the proposed NNPME strategy. Compared with the traditional approaches, the proposed NNPME strategy can significantly enhance system efficiency and ensure stable and continuous operation, even in the presence of uneven power distribution within the MARS system.

14 SOLAR ENERGY↗

DOE OSTI2023

Tech-X contributions to the Center for Tokamak Transients (CTTS) Scientific Discovery through Advanced Computing (SciDAC) project (Final Report)

The Center for Tokamak Transients Simulations (CTTS) consists of computational plasma physicists, computer scientists, and applied mathematicians who are together developing and applying simulation software to improve our understanding of and ability to predict and control transient events in tokamak discharges, particularly those that lead to violent disruptions. We have major simulation activities concerning disruptions that are caused by violating ideal MHD stability criteria, vertical displacement events, resistive wall modes, and tearing modes. We are performing comprehensive modeling of disruption mitigation techniques, particularly by shattered pellet injection (SPI). The Center is built around two mature extended MHD codes: NIMROD and M3D-C1. These codes are being extended in a number of ways as required by the demands of disruption modeling, and are being optimized to work well for larger problem size and modern computer architectures as required to model tokamak plasmas with realistic parameters over the required timescales. The codes will be coupled to the FronTier code for state-of-the-art modeling of SPI. Validation with experimental data on DIII-D, NSTX, and JET is being facilitated by rigorous uncertainty quantification (UQ). The high-level objectives of the center are to: (1) Develop better understanding and improved predictive capability of when crossing a linear stability boundary will likely lead to a disruption, (2) Provide a tool for calculating vessel forces, both axisymmetric and non-axisymmetric, for worst case VDE and other disruptions in tokamaks, (3) Develop increased understanding and improved predictive capability for locked mode disruptions and how best to avoid them, (4) Develop, verify, and validate 3D models for disruption mitigation by shattered pellets that can be used to design and optimize a system for future tokamaks, and (5) Increase the efficiency and scalability of the M3D-C1 and NIMROD codes so that they can model disruptions in ITER scale devices using the most powerful DOE HPC hardware, and (6) Demonstrate code-coupling via FronTier coupling with NIMROD and M3D-C1 and by interfacing these codes within a WDM framework.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Heat Transfer, Refrigeration and Heat Pumps

The Special Issue entitled “Heat Transfer, Refrigeration and heat Pumps” accepted papers covering a wide range of topics related to heat pumps, thermal energy storage, and low-Global Warming Potential (GWP) alternative refrigerants. Heat pumps play a vital role in providing space conditioning and water heating while utilizing the energy of the environment. Since heat pumps use renewable thermal energy from the environs to provide the desired utility, they contribute to the portfolio of technologies that mitigate carbon footprint. The heat pump may be considered a truly renewable technology if the electricity it uses comes entirely from a renewable source. More accurately, a heat pump is a “low carbon technology”. These perspectives make heat pumps an indispensable option for the future in order to reduce the nocuous human impact on the environment. More efficient heat pumping technologies are being developed for the residential, commercial, and industrial sectors of the economy. Another R&D thrust is heat pumps for cold climates. Hardware components, use of low-GWP refrigerants, and identification of systemic inefficiencies are active research areas. This article is a synopsis of the papers submitted to the Special Issue.

42 ENGINEERING↗

NASA NTRS1991

An interactive system for analysis of global cloud imagery

Synoptic images of the global cloud pattern composited from six contemporaneous satellites provide an unprecedented view of the global cloud field. Having horizontal resolution of about 0.5 deg and temporal resolution of 3 h, the global cloud imagery (GCI) resolves most of the variability of organized convection, including several harmonics of the diurnal cycle. Although the GCI has these attractive features, the dense and 3D nature of that data make it a formidable volume of information to treat in a practical and efficient manner. An interactive image-analysis system (IAS) has been developed to investigate the space-time variability of global cloud behavior. In the IAS, data, hardware, and software are integrated into a single system providing a variety of space-time covariance analyses in a menu-driven format. Owing to its customized architecture and certain homogeneous properties of the GCI, the IAS calculates such quantities effectively. Many covariance statistics are derived from 3D data with interactive speed, allowing the user to interrogate the archive iteratively in a single session. The 3D nature of those analyses and the speed with which they are performed distinguish the IAS from conventional image processing of 2D data.

Woodberry, Karen↗

NASA NTRS2009

Development of a Modified Vacuum Cleaner for Lunar Surface Systems

The National Aeronautics and Space Administration (NASA) mission to expand space exploration will return humans to the Moon with the goal of maintaining a long-term presence. One challenge that NASA will face returning to the Moon is managing the lunar regolith found on the Moon's surface, which will collect on extravehicular activity (EVA) suits and other equipment. Based on the Apollo experience, the issues astronauts encountered with lunar regolith included eye/lung irritation, and various hardware failures (seals, screw threads, electrical connectors and fabric contamination), which were all related to inadequate lunar regolith mitigation. A vacuum cleaner capable of detaching, transferring, and efficiently capturing lunar regolith has been proposed as a method to mitigate the lunar regolith problem in the habitable environment on lunar surface. In order to develop this vacuum, a modified "off-the-shelf" vacuum cleaner has been used to determine detachment efficiency, vacuum requirements, and optimal cleaning techniques to ensure efficient dust removal in habitable lunar surfaces, EVA spacesuits, and air exchange volume. During the initial development of the Lunar Surface System vacuum cleaner, systematic testing was performed with varying flow rates on multiple surfaces (fabrics and metallics), atmospheric (14.7 psia) and reduced pressures (10.2 and 8.3 psia), different vacuum tool attachments, and several vacuum cleaning techniques to determine the performance requirements for the vacuum cleaner. The data recorded during testing was evaluated by calculating percent removal, relative to the retained simulant on the tested surface. In addition, Scanning Electron Microscopy (SEM) imaging was used to determine particle size distribution retained on the surface. The scope of this paper is to explain the initial phase of vacuum cleaner development, including historical Apollo mission data, current state-of-the-art vacuum cleaner technology, and vacuum cleaner testing that has focused on detachment capabilities varying pressure environments.

Toon, Katherine P.↗

NASA NTRS2010

Development of a Modified Vacuum Cleaner for Lunar Surface Systems

The National Aeronautics and Space Administration (NASA) mission to expand space exploration will return humans to the Moon with the goal of maintaining a long-term presence. One challenge that NASA will face returning to the Moon is managing the lunar regolith found on the Moon's surface, which will collect on extravehicular activity (EVA) suits and other equipment. Based on the Apollo experience, the issues astronauts encountered with lunar regolith included eye/lung irritation, and various hardware failures (seals, screw threads, electrical connectors and fabric contamination), which were all related to inadequate lunar regolith mitigation. A vacuum cleaner capable of detaching, transferring, and efficiently capturing lunar regolith has been proposed as a method to mitigate the lunar regolith problem in the habitable environment on lunar surface. In order to develop this vacuum, a modified "off-the-shelf' vacuum cleaner will be used to determine detachment efficiency, vacuum requirements, and optimal cleaning techniques to ensure efficient dust removal in habitable lunar surfaces, EVA spacesuits, and air exchange volume. During the initial development of the Lunar Surface System vacuum cleaner, systematic testing was performed with varying flow rates on multiple surfaces (fabrics and metallics), atmospheric (14.7 psia) and reduced pressures (10.2 and 8.3 psia), different vacuum tool attachments, and several vacuum cleaning techniques in order to determine the performance requirements for the vacuum cleaner. The data recorded during testing was evaluated by calculating particulate removal, relative to the retained simulant on the tested surface. In addition, optical microscopy was used to determine particle size distribution retained on the surface. The scope of this paper is to explain the initial phase of vacuum cleaner development, including historical Apollo mission data, current state-of-the-art vacuum cleaner technology, and vacuum cleaner testing that has focused on detachment capabilities at varying pressure environments.

Toon, Katherine P.↗