SEARCH · Engineering Papers

Results for “edge effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Direct Detection Doppler Lidar for Spaceborne Wind Measurement

The theory of double edge lidar techniques for measuring the atmospheric wind using aerosol and molecular backscatter is described. Two high spectral resolution filters with opposite slopes are located about the laser frequency for the aerosol based measurement or in the wings of the Rayleigh - Brillouin profile for the molecular measurement. This doubles the signal change per unit Doppler shift and improves the measurement accuracy by nearly a factor of 2 relative to the single edge technique. For the aerosol based measurement, the use of two high resolution edge filters reduces the effects of background, Rayleigh scattering, by as much as an order of magnitude and substantially improves the measurement accuracy. Also, we describe a method that allows the Rayleigh and aerosol components of the signal to be independently determined. A measurement accuracy of 1.2 m/s can be obtained for a signal level of 1000 detected photons which corresponds to signal levels in the boundary layer. For the molecular based measurement, we describe the use of a crossover region where the sensitivity of a molecular and aerosol-based measurement are equal. This desensitizes the molecular measurement to the effects of aerosol scattering and greatly simplifies the measurement. Simulations using a conical scanning spaceborne lidar at 355 nm give an accuracy of 2-3 m/s for altitudes of 2-15 km for a 1 km vertical resolution, a satellite altitude of 400 km, and a 200 km x 200 km spatial.

Korb, C. Laurence↗

NASA NTRS2001

Simulation of Flow Control Using Deformable Surfaces

The goal of this investigation is to numerically simulate the effects of oscillatory actuators placed on the leading edge of an airfoil, and to quantify the effects of oscillatory blowing on an airfoil stall behavior. It has been demonstrated experimentally that periodic blowing can delay flow separation at high angle of attack. The computations are to be performed for a TAU 0015 airfoil at a high Reynolds number of approx. 1 x 10(exp 6) with turbulent flow conditions. The two-equation Wilcox k - w turbulence model has been shown to provide reliable descriptions of transition and turbulence at high Reynolds numbers. The results are to be compared to Seifert's experimental data.

Truman, C. Randall↗

NASA NTRS2003

Vortex Flows at Supersonic Speeds

A review of research conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) into high-speed vortex flows during the 1970s, 1980s, and 1990s is presented. The data are for flat plates, cavities, bodies, missiles, wings, and aircraft with Mach numbers of 1.5 to 4.6. Data are presented to show the types of vortex structures that occur at supersonic speeds and the impact of these flow structures on vehicle performance and control. The data show the presence of both small- and large-scale vortex structures for a variety of vehicles, from missiles to transports. For cavities, the data show very complex multiple vortex structures exist at all combinations of cavity depth to length ratios and Mach number. The data for missiles show the existence of very strong interference effects between body and/or fin vortices. Data are shown that highlight the effect of leading-edge sweep, leading-edge bluntness, wing thickness, location of maximum thickness, and camber on the aerodynamics of and flow over delta wings. Finally, a discussion of a design approach for wings that use vortex flows for improved aerodynamic performance at supersonic speeds is presented.

Wood, Richard M.↗

NASA NTRS2005

RTO Technical Publications: A Quarterly Listing

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information covering the period from July 1, 2005 to September 30, 2005; and available in the NASA Aeronautics and Space Database. Contents include: Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing; Actively Controlling Buffet-Induced Excitations; Modelling and Simulation to Address NATO's New and Existing Military Requirements; Latency in Visionic Systems: Test Methods and Requirements; Personal Hearing Protection including Active Noise Reduction; Virtual Laboratory Enabling Collaborative Research in Applied Vehicle Technologies; A Method to Analyze Tail Buffet Loads of Aircraft; Particle Image Velocimetry Measurements to Evaluate the Effectiveness of Deck-Edge Columnar Vortex Generators on Aircraft Carriers; Introduction to Flight Test Engineering, Volume 14; Pathological Aspects and Associated Biodynamics in Aircraft Accident Investigation;

Source record↗

NASA NTRS2010

Reflector Surface Error Compensation in Dual-Reflector Antennas

By probing the field on a small subreflector at a minimal number of points, the main reflector surface errors can be obtained and subsequently used to design a phase-correction subreflector that can compensate for main reflector errors. The compensating phase-error profile across the subreflector can be achieved either by a surface deformation or by the use of an array of elements such as patch antennas that can cause a phase shift between the incoming and outgoing fields. The second option is of primary interest here, but the methodology can be applied to either case. The patch array is most easily implemented on a planar surface. Therefore, the example of a flat subreflector and a parabolic main reflector (a Newtonian dual reflector system) is considered in this work. The subreflector is assumed to be a reflector array covered with patch elements. The phase variation on a subreflector can be detected by a small number of receiving patch elements (probes). By probing the phase change at these few selected positions on the subreflector, the phase error over the entire surface can be recovered and used to change the phase of all the patch elements covering the subreflector plane to compensate for main reflector errors. This is accomplished by using a version of sampling theorem on the circular aperture. The sampling is performed on the phase-error function on the circular aperture of the main reflector by a method developed using Zernike polynomials. This method is based upon and extended from a theory previously proposed and applied to reflector aperture integration. This sampling method provides for an exact retrieval of the coefficients of up to certain orders in the expansion of the phase function, from values on a specifically calculated set of points in radial and azimuthal directions in the polar coordinate system, on the circular reflector aperture. The corresponding points on the subreflector are then obtained and, by probing the fields at these points, a set of phase values is determined that is then transferred back to the main reflector aperture for recovering the phase function. Once this function is recovered, the corresponding phase function on the subreflector is calculated and used to compensate for main reflector surface errors. In going back and forth between sub and main reflectors, geometrical (ray) optics is employed, which even though it ignores edge diffraction and other effects, is shown to be accurate for phase recovery.

Jamnejad, Vahraz↗

NASA NTRS2020

The Late-time Afterglow Evolution of Long Gamma-Ray Bursts GRB 160625B and GRB 160509A

We present post-jet-break Hubble Space Telescope, Very Large Array, and Chandra observations of the afterglow of the long γ-ray bursts GRB 160625B (between 69 and 209 days) and GRB 160509A (between 35 and 80 days). We calculate the post-jet-break decline rates of the light curves and find the afterglow of GRB 160625B is inconsistent with a simple t−3/4 steepening over the break, expected from the geometric effect of the jet edge entering our line of sight. However, the favored optical post-break decline (fv alpha t-1.96+-0.07) is also inconsistent with the fν alpha t−p decline (where p ≈ 2.3 from the pre-break light curve), which is expected from exponential lateral expansion of the jet; perhaps suggesting lateral expansion that only affects a fraction of the jet. The post break decline of GRB 160509A is consistent with both the t−3/4 steepening and with fν alpha t−p. We also use BOXFIT to fit afterglow models to both light curves and find both to be energetically consistent with a millisecond magnetar central engine, but the magnetar parameters need to be extreme (i.e., E ~ 3 × 1052 erg). Finally, the late-time radio light curves of both afterglows are not reproduced well by BOXFIT and are inconsistent with predictions from the standard jet model; instead, both are well represented by a single power-law decline (roughly fν alpha t−1) with no breaks. This requires a highly chromatic jet break (tj, radio > 10 x tj, optical) and possibly a two-component jet for both bursts.

Gamma-ray bursts↗

NASA NTRSDate not supplied

Pterodactyl: Effects of 3D Thermal Analysis on Thermal Protection System Design for a Flap Control System

NASA’s Pterodactyl project has investigated the use of a novel multi-flap control system to facilitate precision targeting of Deployable Entry Vehicles (DEVs) during atmospheric re-entry [1]. DEVs can be folded to fit within the limiting cross-sectional area of current launch systems. Once deployed, the vehicle expands and settles into a pre-determined blunt body shape. While DEVs provide a more efficient solution to increased payload sizes, the absence of a back shell does not allow for easy integration of reaction control systems, which have historically been used for guidance and control (G&C) of rigid aeroshells during entry. One DEV solution, called the Adaptable, Deployable Entry Placement Technology (ADEPT), employs mechanically deployed gores. This provided the Pterodactyl project with the opportunity to incorporate a rib-mounted, 8-flap control system for G&C. Each flap can deflect independently in and out of the hypersonic flow, requiring TPS for the flaps. Previous work within the Pterodactyl project utilized 1D thermal analysis to design the TPS. However, the Pterodactyl project was concerned that the base level tools for 1D thermal analysis were not accounting for the 3D effects of the large heating gradients along and across the flaps, the in-depth in-plane conductivity of the TPS and internal structure, and the effects of the small edge radii at the neck of the flaps. This paper discusses the methodology and results of a 3D thermal analysis of the flap control system. Additionally, the results from the 1D and 3D thermal analyses are compared. It is found that elements of the original design that resulted from the 1D analysis may be overly conservative, and implementation of a 3D thermal analysis indicated a reduction in TPS thickness is feasible. This result helps to reduce the mechanical integration complexity of the flap at the rib tip and realizes potential mass savings.

Sarah N D'Souza↗

NASA NTRS1948

The effectiveness at high speeds of a 10-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section

This report contains the results of a high-speed wind-tunnel investigation of the effectiveness of a 10-percent-chord plain flap on the NACA 65-210 airfoil section. The results include an indication of the lift-producing characteristics and the effectiveness of the 10-percent-chord flap. From a comparison of the characteristics of the 10-percent-chord flap with those of a 20-percent-chord flap it was concluded that, although a reduction in flap-chord ratio from 0.20 to 0.10 lessens the severity of the effectiveness loss at supercritical speeds, the 20-percent-chord flap is more effective throughout the entire range of Mach numbers from 0.3 to 0.875.

CONTROLS, FLAP TYPE - WING SECTIONS↗

NASA NTRS1991

Effects of sweep angle and passive relaminarization devices on a supersonic swept-cylinder boundary layer

The effects of passive leading-edge devices on the boundary layer of a swept cylinder in supersonic flow with very low free-stream disturbance levels are investigated. Tests are conducted at Mach 3.5 over a free-stream Reynolds number based on model diameter of 15,000 to 150,000, and sweep angles of 60 deg and 76 deg are used to evaluate possible sweep-angle effects. The devices tested include a sawtoothed leading edge, square device, and a fence. It is observed that at a sweep angle of 76 deg, relaminarization of the supersonic attachment-line flow is achieved by several of the devices, while no devices are successful at a sweep angle of 60 deg.

Creel, T. R.↗

NASA NTRS1982

Recent advances in applying Free Vortex Sheet theory to the estimation of vortex flow aerodynamics

Free Vortex Sheet theory has been applied to a variety of configurations for the estimation of three-dimensional pressure distributions for wings developing separation-induced leading-edge vortex flows. Correlations with experiment show reasonable estimates for the effects of compressibility, side-slip, side edges, swept-wing blast-induced loads, and leading-edge vortex flaps. Theoretical studies expand upon these correlations to show general aerodynamic trends. Consideration is also given to simple, yet effective techniques which expedite convergence and therefore reduce computational expense.

Luckring, J. M.↗

NASA NTRS1981

Vortex-flow aerodynamics - An emerging design capability

Promising current theoretical and simulational developments in the field of leading edge vortex-generating delta, arrow ogival wings are reported, along with the history of theory and experiment leading to them. The effects of wing slenderness, leading edge nose radius, Mach number and incidence variations, and planform on the onset of vortex generation and redistribution of aerodynamic loads are considered. The range of design possibilities in this field are consequential for the future development of strategic aircraft, supersonic transports and commercial cargo aircraft which will possess low-speed, high-lift capability by virtue of leading edge vortex generation and control without recourse to heavy and expensive leading edge high-lift devices and compound airfoils. Attention is given to interactive graphics simulation devices recently developed.

Campbell, J. F.↗

NASA NTRS1984

Engineering analysis of drooped leading-edge wings near stall

Numerical results obtained with a three-dimensional vortex panel computer program for the calculation of inviscid, incompressible (potential) flow over infinitely thin finite wings with camber are presented. The program, which is designed for wings with drooped leading edge discontinuities, is essentially a numerical representation of lifting surface theory, involving both spanwise and chordwise distributions of vorticity. The results also include two engineering approximations. First, the effect of the leading-edge discontinuities is modeled by assuming that the vortices emanating from the discontinuities aerodynamically divide the wing into three distinct sections of lower aspect ratio. Secondly, the effect of the separated flow at high angle of attack is modeled by applying rectangular vortex panels with a varying vortex strength over the portions of the wing with attached flow.

Anderson, J. D., Jr.↗

NASA NTRS1975

Flow visualization of leading-edge vortex enhancement by spanwise blowing

Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.

Erickson, G. E.↗

DOE OSTI2024

High-temperature quantum valley Hall effect with quantized resistance and a topological switch

Edge states of a topological insulator can be used to explore fundamental science emerging at the interface of low dimensionality and topology. Achieving a robust conductance quantization, however, has proven challenging for helical edge states. In this work, we show wide resistance plateaus in kink states—a manifestation of the quantum valley Hall effect in Bernal bilayer graphene—quantized to the predicted value at zero magnetic field. The plateau resistance has a very weak temperature dependence up to 50 kelvin and is flat within a dc bias window of tens of millivolts. We demonstrate the electrical operation of a topology-controlled switch with an on/off ratio of 200. These results demonstrate the robustness and tunability of the kink states and its promise in constructing electron quantum optics devices.

Science & Technology - Other Topics↗

NASA NTRS1975

The effect of grazing flow on the steady state resistance of square-edged orifices

A simple inviscid interaction model has been developed which uses thin airfoil theory to account for pressure forces exerted at the interface between the orifice and grazing flow together with a one-dimensional discharge coefficient concept. The effect of grazing flow boundary layer thickness was also included in the model. Resistance measurements for a wide range of grazing flow speeds and orifice flow rates collapse into a single curve when plotted in terms of effective discharge coefficient versus orifice-to-grazing velocity ratio. The correlation curves for inflow and outflow are different. Data for clustered orifices collapse in the same way as the single orifice. The effect of boundary layer thickness is compared with model predictions. The effect of orifice length-diameter ratio is shown to be significant for inflow but negligible for outflow.

Rogers, T.↗

NASA NTRS2010

Separating Real and Apparent Effects of Cloud, Humidity, and Dynamics on Aerosol Optical Thickness near Cloud Edges

Aerosol optical thickness (AOT) is one of aerosol parameters that can be measured on a routine basis with reasonable accuracy from Sun-photometric observations at the surface. However, AOT-derived near clouds is fraught with various real effects and artifacts, posing a big challenge for studying aerosol and cloud interactions. Recently, several studies have reported correlations between AOT and cloud cover, pointing to potential cloud contamination and the aerosol humidification effect; however, not many quantitative assessments have been made. In this study, various potential causes of apparent correlations are investigated in order to separate the real effects from the artifacts, using well-maintained observations from the Aerosol Robotic Network, Total Sky Imager, airborne nephelometer, etc., over the Southern Great Plains site operated by the U.S. Department of Energy's Atmospheric Radiation Measurement Program. It was found that aerosol humidification effects can explain about one fourth of the correlation between the cloud cover and AOT. New particle genesis, cloud-processed particles, atmospheric dynamics, and aerosol indirect effects are likely to be contributing to as much as the remaining three fourth of the relationship between cloud cover and AOT.

Jeong, Myeong-Jae↗

NASA NTRS1970

Hypersonic research engine project. Phase 2: Aerothermodynamic integration model development

The analytical effort was directed towards (1) completing the design of the combustor exit instrumentation assembly, (2) analyzing the coolant flow distribution of the cowl leading edge tip section, (3) determining effects of purge gas pressure on AIM performance analysis, and (4) analyzing heat transfer and associated stress problems related to the cowl leading edge tip section and the nozzle shroud assembly for test conditions.

Jilly, L. F.↗

NASA NTRS1993

Computational analysis of off-design waveriders

Comprehensive inviscid and viscous numerical simulations of hypersonic flow past nonconical rounded-nose waveriders are presented. The flow fields and aerodynamic forces at off-design conditions are determined inviscidly by a space-marching CFD code with the initial-data plane provided by a time-marching Navier-Stokes CFD code. Off-design conditions include off-design Mach numbers, angles of attack, and rounded leading edges. A wide range of waverider configurations is investigated and compared. These calculations show the effects of viscous interactions, which are influential near the leading edges, and determine the viscous drag. The inviscid calculations show that L/D decreases as freestream M increases (with alpha = 0). At the on-design Mach numbers, the maximum L/D may occur at slight positive or negative alpha, depending on the shape of the waverider, and zero lift occurs at a negative alpha approximately equal to half of the body thickness. The effects of slight leading-edge blunting produce only local effects in the flow field and small losses in L/D.

He, X.↗