Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamic control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Dynamic modeling and adaptive control for space stations

Of all large space structural systems, space stations present a unique challenge and requirement to advanced control technology. Their operations require control system stability over an extremely broad range of parameter changes and high level of disturbances. During shuttle docking the system mass may suddenly increase by more than 100% and during station assembly the mass may vary even more drastically. These coupled with the inherent dynamic model uncertainties associated with large space structural systems require highly sophisticated control systems that can grow as the stations evolve and cope with the uncertainties and time-varying elements to maintain the stability and pointing of the space stations. The aspects of space station operational properties are first examined, including configurations, dynamic models, shuttle docking contact dynamics, solar panel interaction, and load reduction to yield a set of system models and conditions. A model reference adaptive control algorithm along with the inner-loop plant augmentation design for controlling the space stations under severe operational conditions of shuttle docking, excessive model parameter errors, and model truncation are then investigated. The instability problem caused by the zero-frequency rigid body modes and a proposed solution using plant augmentation are addressed. Two sets of sufficient conditions which guarantee the globablly asymptotic stability for the space station systems are obtained.

Ih, C. H. C.↗
NASA NTRS1985

Dynamic assertion testing of flight control software

An experiment in using assertions to dynamically test fault tolerant flight software is described. The experiment showed that 87% of typical errors introduced into the program would be detected by assertions. Detailed analysis of the test data showed that the number of assertions needed to detect those errors could be reduced to a minimal set. The analysis also revealed that the most effective assertions tested program parameters that provided greater indirect (collateral) testing of other parameters.

Andrews, D. M.↗
NASA NTRS1992

Dynamic characterization, monitoring and control of rotating flexible beam-mass structures via piezo-embedded techniques

A variational principle and a finite element discretization technique were used to derive the dynamic equations for a high speed rotating flexible beam-mass system embedded with piezo-electric materials. The dynamic equation thus obtained allows the development of finite element models which accommodate both the original structural element and the piezoelectric element. The solutions of finite element models provide system dynamics needed to design a sensing system. The characterization of gyroscopic effect and damping capacity of smart rotating devices are addressed. Several simulation examples are presented to validate the analytical solution.

Lai, Steven H.-Y.↗
NASA NTRS2004

Controls and Health Management Technologies for Intelligent Aerospace Propulsion Systems

With the increased emphasis on aircraft safety, enhanced performance and affordability, and the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Technology Branch at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC) in Cleveland, Ohio, is leading and participating in various projects in partnership with other organizations within GRC and across NASA, the U.S. aerospace industry, and academia to develop advanced controls and health management technologies that will help meet these challenges through the concept of an Intelligent Engine. The key enabling technologies for an Intelligent Engine are the increased efficiencies of components through active control, advanced diagnostics and prognostics integrated with intelligent engine control to enhance component life, and distributed control with smart sensors and actuators in an adaptive fault tolerant architecture. This paper describes the current activities of the Controls and Dynamics Technology Branch in the areas of active component control and propulsion system intelligent control, and presents some recent analytical and experimental results in these areas.

Garg, Sanjay↗
NASA NTRSDate not supplied

Structure and Dynamics of Bleed-Controlled Impinging Shock/Turbulent-Boundary-Layer Interactions

Porous boundary-layer bleed is often employed to alleviate the detrimental effects of shock/turbulent-boundary-layer interactions (STBLI) in high-speed vehicles. However, outstanding questions remain on the underlying mechanisms through which bleed influences STBLI dynamics. This work addresses this knowledge gap by performing a scale-resolved Large-Eddy Simulation of an impinging STBLI controlled by discrete bleed holes. The simulation has a freestream Mach number of 2.5, an oblique shock generator angle of 8 degrees, and a Reynolds number based on the incoming momentum thickness of 2800. Bleed substantially reduces the separation size and upstream influence of the STBLI compared to the canonical, uncontrolled case. Consequently, the characteristic, low-frequency motion of STBLI-induced separation is mitigated, as revealed by wall-pressure spectra. Energy is shifted from the low frequency separation behavior to a higher-frequency signature caused by the bleed shocks and expansions. The scale-resolved simulations also reveal that these small, localized structures severely limit the turbulence production traditionally seen in the uncontrolled interaction.

computational fluid dynamics↗
NASA NTRS1986

Active Control Evaluation for Spacecraft (ACES)

The Air Force goal is to develop vibration control techniques for large flexible spacecraft by addressing sensor, actuator, and control hardware and dynamic testing. The Active Control Evaluation for Spacecraft (ACES) program will address the Air Force goal by looking at two leading control techniques and implementing them on a structural model of a flexible spacecraft under laboratory testing. The first phase in the ACES program is to review and to assess the High Authority Control/Low Authority Control (HAC/LAC) and Filter accomodated Model Error Sensitivity Suppression (FAMESS) control techniques for testing on the modified VCOSS structure. Appropriate sensors and actuators will be available for use with both techniques; locations will be the same for both techniques. The control actuators will be positioned at the midpoint and free end of the structure. The laser source for the optical sensor is mounted on the feed mast. The beam will be reflected from a mirror on the offset antenna onto the detectors mounted above the shaker table bay. The next phase is to develop an analysis simulation with the control algorithms implemented for dynamics verification. The third phase is to convert the control laws into high level computer language and test them in the NASA-MSFC facility. The final phase is to compile all analytical and test results for performance comparisons.

Pearson, J.↗
NASA NTRS1999

Combustion Instabilities Modeled

NASA Lewis Research Center's Advanced Controls and Dynamics Technology Branch is investigating active control strategies to mitigate or eliminate the combustion instabilities prevalent in lean-burning, low-emission combustors. These instabilities result from coupling between the heat-release mechanisms of the burning process and the acoustic flow field of the combustor. Control design and implementation require a simulation capability that is both fast and accurate. It must capture the essential physics of the system, yet be as simple as possible. A quasi-one-dimensional, computational fluid dynamics (CFD) based simulation has been developed which may meet these requirements. The Euler equations of mass, momentum, and energy have been used, along with a single reactive species transport equation to simulate coupled thermoacoustic oscillations. A very simple numerical integration scheme was chosen to reduce computing time. Robust boundary condition procedures were incorporated to simulate various flow conditions (e.g., valves, open ends, and choked inflow) as well as to accommodate flow reversals that may arise during large flow-field oscillations. The accompanying figure shows a sample simulation result. A combustor with an open inlet, a choked outlet, and a large constriction approximately two thirds of the way down the length is shown. The middle plot shows normalized, time-averaged distributions of the relevant flow quantities, and the bottom plot illustrates the acoustic mode shape of the resulting thermoacoustic oscillation. For this simulation, the limit cycle peak-to-peak pressure fluctuations were 13 percent of the mean. The simulation used 100 numerical cells. The total normalized simulation time was 50 units (approximately 15 oscillations), which took 26 sec on a Sun Ultra2.

Paxson, Daniel E.↗
NASA NTRS1986

Stochastic modeling and control system designs of the NASA/MSFC Ground Facility for large space structures: The maximum entropy/optimal projection approach

In the Control Systems Division of the Systems Dynamics Laboratory of the NASA/MSFC, a Ground Facility (GF), in which the dynamics and control system concepts being considered for Large Space Structures (LSS) applications can be verified, was designed and built. One of the important aspects of the GF is to design an analytical model which will be as close to experimental data as possible so that a feasible control law can be generated. Using Hyland's Maximum Entropy/Optimal Projection Approach, a procedure was developed in which the maximum entropy principle is used for stochastic modeling and the optimal projection technique is used for a reduced-order dynamic compensator design for a high-order plant.

Hsia, Wei-Shen↗
NASA NTRS1992

Mechanism synthesis and 2-D control designs of an active three cable crane

A Lunar Crane with a suspension system based on a three cable mechanism is investigated to provide a stable end-effector for hoisting, positioning, and assembling large components during construction and servicing of a Lunar Base. The three cable suspension mechanism consists of a structural framework of three cables pointing to a common point that closely coincides with the suspended payload's center of gravity. The vibrational characteristics of this three cable suspension system are investigated by comparing a simple 2-D symmetric suspension model and a swinging pendulum in terms of their analytical natural frequency equations. A study is also made of actively controlling the dynamics of the crane using two different actuator concepts. Also, Lyapunov-based control algorithms are developed to determine two regulator-type control laws performing the system vibrational suppression for both system dynamics. Simulations including initial-valued dynamic responses as well as control performances for two different system dynamics are also presented.

Yang, Li-Farn↗
NASA NTRS2014

Low-Speed Dynamic Wind Tunnel Test Analysis of a Generic 53 Degree Swept UCAV Configuration With Controls

Several static and dynamic forced-motion wind tunnel tests have been conducted on a generic unmanned combat air vehicle (UCAV) configuration with a 53deg swept leading edge. These tests are part of an international research effort to assess and advance the state-of-art of computational fluid dynamics (CFD) methods to predict the static and dynamic stability and control characteristics for this type of configuration. This paper describes the dynamic forced motion data collected from two different models of this UCAV configuration as well as analysis of the control surface deflections on the dynamic forces and moments.

Vicroy, Dan D.↗
NASA NTRS1983

Dynamic analysis for robot arm control

Explicit state equations provide detailed analytic insight into the dynamic behavior of a robot arm and facilitate the understanding of the control problem. The analytic strength of explicit state equations is exemplified for a given robot arm. In fact, for the quoted example, the explicit and exact state equations involve considerably less computation than the use of the known most efficient general-purpose computational algorithm for robot arm dynamics.

Bejczy, A. K.↗
NASA NTRS1991

Centralized, decentralized, and independent control of a flexible manipulator on a flexible base

The dynamics and control of a flexible manipulator arm with payload mass on a flexible base in space are considered. The controllers are provided by one torquer at the center of the base and one torquer at the connection joint of the robot and the base. The nonlinear dynamics of the system is modeled by applying the finite element method and Lagrangian formula. Three control strategies are considered and compared, i.e., centralized control, decentralized control, and independent control. All these control designs are based on the linear quadratic regulator theory. A mathematical decomposition is used in the decentralization process so that the coupling between the subsystems is weak, while a physical decomposition is used in the independent control design process. For both the decentralized and the independent controls, the stability of the overall linear system is checked before a numerical simulations is initiated. Two numerical examples show that the response of the independent control system are close to those of the centralized control system, while the responses of the decentralized control system are not.

Li, Feiyue↗
NASA NTRS1973

A model based technique for the design of flight directors

A new technique for designing flight directors is discussed. This technique uses the optimal-control pilot/vehicle model to determine the appropriate control strategy. The dynamics of this control strategy are then incorporated into the director control laws, thereby enabling the pilot to operate at a significantly lower workload. A preliminary design of a control director for maintaining a STOL vehicle on the approach path in the presence of random air turbulence is evaluated. By selecting model parameters in terms of allowable path deviations and pilot workload levels, a set of director laws is achieved which allows improved system performance at reduced workload levels. The pilot acts essentially as a proportional controller with regard to the director signals, and control motions are compatible with those appropriate to status-only displays.

Levison, W. H.↗
NASA NTRS1980

Pointing and control for planetary spacecraft - The first twenty years

The evolution of guidance and control systems for United States planetary and unmanned lunar spacecraft over the last 20 years is traced. The characteristics of the guidance and control systems used on spacecraft from the Range lunar impactor to the planned Galileo Jupiter orbiter and entry probe are surveyed, with attention given to the uses of three-axis stabilized, spin-stabilized and dual-spin designs. System performance trends that have evolved to meet the increasing science and mission requirements of the spacecraft are considered in the areas of attitude references, control consumables, dynamics and system modeling, thrust vector control, optical navigation, manuever turns, maneuver velocity control, instrument pointing, and antenna pointing. Hardware trends in optical sensors, inertial sensors, processing electronics, electromechanical devices, and system testing and reliability are also reviewed. The achievements represented by these advances are emphasized, and it is predicted that future developments will be in the areas of increased control system autonomy and performance requirements.

Pace, G. D.↗
NASA NTRS1985

High-speed, automatic controller design considerations for integrating array processor, multi-microprocessor, and host computer system architectures

Modern control systems must typically perform real-time identification and control, as well as coordinate a host of other activities related to user interaction, online graphics, and file management. This paper discusses five global design considerations which are useful to integrate array processor, multimicroprocessor, and host computer system architectures into versatile, high-speed controllers. Such controllers are capable of very high control throughput, and can maintain constant interaction with the nonreal-time or user environment. As an application example, the architecture of a high-speed, closed-loop controller used to actively control helicopter vibration is briefly discussed. Although this system has been designed for use as the controller for real-time rotorcraft dynamics and control studies in a wind tunnel environment, the controller architecture can generally be applied to a wide range of automatic control applications.

Jacklin, S. A.↗