SEARCH · Engineering Papers

Results for “ducts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1991

An eddy viscosity calculation method for a turbulent duct flow

The mean velocity profile across a fully developed turbulent duct flow is obtained from an eddy viscosity relation combined with an empirical outer region wake function. Results are in good agreement with experiments and with direct numerical simulations in the same flow at two Reynolds numbers. In particular, the near-wall trend of the Reynolds shear stress and its variation with Reynolds number are similar to those of the simulations. The eddy viscosity method is more accurate than previous mixing length or implicit function methods.

Antonia, R. A.↗

NASA NTRS1992

Analysis of an advanced ducted propeller subsonic inlet

It is shown that a time marching Navier-Stokes code called PARC can be utilized to provide a reasonable prediction of the flow field within an inlet for an advanced ducted propeller. The code validation was implemented for a nonseparated flow condition associated with the inlet functioning at angles-of-attack of zero and 25 deg. Comparison of the computational results with the test data shows that the PARC code with the propeller face fixed flow properties boundary conditions (BC) provided a better prediction of the inlet surface static pressures than the prediction when the mass flow BC was employed.

Iek, Chanthy↗

NASA NTRS1992

Unsteady flowfield simulation of ducted prop-fan configurations

A technique for the simulation of unsteady flows in and around complex rotating machinery is presented. Additional domain decomposition mechanisms are introduced which extend the range of applicability of software developed for the time-accurate simulation of rotating machinery flowfields. The flow models uses the unsteady 3D Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. Multiblock domain decomposition is used to partition the field radially, axially, as well as circumferentially into an ordered arrangement of blocks which exhibit varying degrees of similarity. A general high-order numerical scheme is applied to satisfy the geometric conservation law. Two configurations are presented - ducted single rotation prop-fan and a rotor-deswirl vane combination which form a single stage fan. Comparisons are made to other numerical solutions for these geometries and to available experimental data.

Janus, J. M.↗

NASA NTRS1992

Analysis of two-dimensional ducts with sudden area changes using the boundary element method

In this paper, the boundary element method (BEM) is applied to two-dimensional acoustic ducts with sudden area changes. The mathematical basis of BEM along with the technique of handling singularities is presented in a systematic manner. The computer code is verified by comparison with the exact solutions and a number of illustrative examples are included.

Pates, Carl S., III↗

NASA NTRS1992

Detonation duct gas generator demonstration program

An experimental demonstration is presented for the generation of detonation waves that move periodically across high speed channel flow; these waves can compress the outflow from a low pressure compressor, and thereby both reduce the compressor requirements associated with conventional gas turbines and enhance thermodynamic efficiency through isochoric energy addition. By generating transient transverse waves, rather than standing waves, shock-wave losses are reduced by an order of magnitude; the result is a Humphrey cycle augmenting the basic Brayton-cycle gas turbine. Attention is presently given to results from an experimental detonation duct.

Wortman, A.↗

NASA NTRS1987

Confined separated-swirling flows in diffusing ducts

The objective is to establish a detailed experimental data base for evaluation of Navier-Stokes codes for confined separated flows in diffusing s-ducts. The computational thrusts include the following: (1) extension and validation of the LeRC parabolized Navier-Stokes solver, PEPSIG, into the separated flow regime using 'flare' type approximations; (2) evaluation and extensions of state-of-the-art turbulence models for confined separated flow with and without swirl; and (3) evaluation and validation of LeRC time marching 3-D Navier-Stokes code, PROTEUS, into confined separate flow regime. Various aspects of the study are presented in viewgraph form.

Anderson, Bernhard H.↗

NASA NTRS1993

Optimization of circular orifice jets mixing into a heated cross flow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

NASA NTRS1993

Effect of a rotating propeller on the separation angle of attack and distortion in ducted propeller inlets

The present study represents an extension of an earlier wind tunnel experiment performed with the P&W 17-in. Advanced Ducted Propeller (ADP) Simulator operating at Mach 0.2. In order to study the effects of a rotating propeller on the inlet flow, data were obtained in the UTRC 10- by 15-Foot Large Subsonic Wind Tunnel with the same hardware and instrumentation, but with the propeller removed. These new tests were performed over a range of flow rates which duplicated flow rates in the powered simulator program. The flow through the inlet was provided by a remotely located vacuum source. A comparison of the results of this flow-through study with the previous data from the powered simulator indicated that in the conventional inlet the propeller produced an increase in the separation angle of attack between 4.0 deg at a specific flow of 22.4 lb/sec-sq ft to 2.7 deg at a higher specific flow of 33.8 lb/sec-sq ft. A similar effect on separation angle of attack was obtained by using stationary blockage rather than a propeller.

Boldman, D. R.↗

NASA NTRS1993

The 3-D viscous flow CFD analysis of the propeller effect on an advanced ducted propeller subsonic inlet

A time marching Navier-Stokes code called PARC3D was used to study the 3-D viscous flow associated with an advanced ducted propeller (ADP) subsonic inlet at take-off operating conditions. At a free stream Mach number of 0.2, experimental data for the inlet-with-propeller test model indicated that the airflow was attached on the cowl windward lip at an angle of attack of 25 degrees became unstable at 29 degrees, and separated at 30 degrees. An experimental study with a similar inlet and with no propeller (through-flow) indicated that flow separation occurred at an angle of attack a few degrees below the value observed when the inlet was tested with the propeller. This tends to indicate that the propeller exerts a favorable effect on the inlet performance. During the through-flow experiment a stationary blockage device was used to successfully simulate the propeller effect on the inlet flow field at angles of attack. In the present numerical study, this flow blockage was modeled via a PARC3D computational boundary condition (BC) called the screen BC. The principle formulation of this BC was based on the one-and-half dimension actuator disk theory. This screen BC was applied at the inlet propeller face station of the computational grid. Numerical results were obtained with and without the screen BC. The application of the screen BC in this numerical study provided results which are similar to the results of past experimental efforts in which either the blockage device or the propeller was used.

Iek, Chanthy↗

NASA NTRS1993

Optimization of circular orifice jets mixing into a heated crossflow in a cylindrical duct

Kroll, J. T.↗

NASA NTRS1993

On the generation of secondary motion in circular to rectangular transition ducts

A computer code has been developed for the calculation of three-dimensional turbulent flow in circular to rectangular transition ducts. The governing equations are written in a general curvilinear coordinate system so that all singly-connected geometrical configurations can be accommodated. Turbulence closure is through the standard k-epsilon model or a Reynolds stress closure model. Computed results show qualitative agreement with experimental data. Pressure-induced secondary flow is the dominant mode through the transition, but turbulence-induced secondary flow becomes prominent some distance downstream of the transition.

Demuren, A. O.↗

NASA NTRS1993

A three-dimensional pressure flux-split RNS application to sub/supersonic flow in inlets and ducts

The reduced Navier-Stokes (RNS) formulation is combined with a pressure based flux split procedure for the computational analysis of three dimensional flow. Only lowest order diffusion, that is required to satisfy the no-slip boundary condition is retained in this approximation. The governing equations are appropriately differenced such that the physical boundary conditions are closely coupled and combined to form a closed discrete system. No numerical or characteristic type boundary conditions are required. A global pressure relaxation procedure, i.e. multi-sweep PNS, is considered. A sparse matrix direct solver is applied to the crossplane solution. At the outflow boundary only the pressure or pressure gradient is prescribed. The resulting formulation has been applied to the solution of three-dimensional subsonic/supersonic internal flows in inlets and ducts.

Khosla, P. K.↗

NASA NTRS1993

3-D viscous flow CFD analysis of the propeller effect on an advanced ducted propeller subsonic inlet

The time-marching Navier-Stokes code PARC3D was used to study the 3D viscous flow associated with an advanced ducted propeller subsonic inlet at take-off operating conditions. At a free stream Mach number of 0.2, experimental data for the inlet-with-propeller test model indicated that the airflow was attached on the cowl windward lip at an angle of attack of 25 deg became unstable at 29 deg, and separated at 30 deg. An experimental study with a similar inlet and without propeller (through-flow) indicated that flow separation occurred at an angle of attack a few degrees below the value observed when the inlet was tested with the propeller, indicating the propeller's favorable effect on inlet performance. In the present numerical study, flow blockage analogous to the propeller was modeled via a PARC3D computational boundary condition (BC), the 'screen BC', based on 1-1/2 dimension actuator disk theory. The application of the screen BC in this numerical study provided results similar to those of past experimental efforts in which either the blockage device or the propeller was used.

Iek, Chanthy↗

NASA NTRS1947

Effect of Modifications to Induction System on Altitude Performance of V-1710-93 Engine III : Use of Parabolic Rotating Guide Vanes and NACA Designed Auxiliary-stage Inlet Elbow and Interstage Duct

Bench runs of a modified V-1710-93 engine equipped with a two-stage supercharger, interstage carburetor, aftercooler assembly, and backfire screens have been made at a simulated altitude of 29,000 feet to determine the effect of several induction-system modifications on the engine and supercharger performance. The standard guide vanes on the auxiliary- and engine-stage superchargers were replaced by rotating guide vanes with a parabolic blade profile. The auxiliary-stage inlet elbow and interstage duct were replaced with new units of NACA design. These modifications were made one at a time and data were obtained after each change to determine the effect of each modification. All runs were made at a constant engine speed of 3000 rpm at a simulated altitude of 29,000 feet and all changes in engine power were made by varying the speed of the auxiliary-stage supercharger.

Standahar, Ray M↗

NASA NTRS1948

An experimental investigation of the design variables for NACA submerged duct entrances

Information concerning the parameters and design variables affecting an NACA submerged duct design is presented.

Mossman, Emmet A↗

NASA NTRS1939

Contribution to the theory of the heated duct radiator

A method is developed with no neglect of certain factors in mass flow of air and in the drag of the heated radiator, i.e., one under actual operating conditions, as compared with the corresponding values in the cold state, may be simply computed. Although a symmetrical duct radiator has been used to bring out the flow relations, the results apply equally as well to the unsymmetrical radiator shapes usual in airplane construction.

Winter, H↗

NASA NTRS1993

A comparative study of full Navier-Stokes and Reduced Navier-Stokes analyses for separating flows within a diffusing inlet S-duct

A three-dimensional implicit Full Navier-Stokes (FNS) analysis and a 3D Reduced Navier-Stokes (RNS) initial value space marching solution technique has been applied to a class of separate flow problems within a diffusing S-duct configuration characterized as vortex-liftoff. Both Full Navier-Stokes and Reduced Navier-Stokes solution techniques were able to capture the overall flow physics of vortex lift-off, however more consideration must be given to the development of turbulence models for the prediction of the locations of separation and reattachment. This accounts for some of the discrepancies in the prediction of the relevant inlet distortion descriptors, particularly circumferential distortion. The 3D RNS solution technique adequately described the topological structure of flow separation associated with vortex lift-off.

Anderson, B. H.↗

NASA NTRS1993

Cruise noise measurements of a scale model advanced ducted propulsor

A scale model Advanced Ducted Propulsor (ADP) was tested in NASA Lewis Research Center's 8- by 6-Foot Wind Tunnel to obtain acoustic data at cruise conditions. The model, designed and manufactured by Pratt & Whitney Division of United Technologies, was tested with three inlet lengths. The model has 16 rotor blades and 22 stator vanes, which results in a cut-on condition with respect to rotor-stator interaction noise. Comparisons of the noise directivity of the ADP with that of a previously tested high-speed, unducted propeller showed that the ADP peak blade passing tone was about 30 dB below that of the propeller, and therefore, should not present a cabin or enroute noise problem. The maximum blade passing tone first increased with increasing helical tip Mach number, peaked, and then decreased at a higher Mach number. The ADP tests with the shortest inlet showed more noise in the inlet arc than did tests with either of the other two inlet lengths.

Dittmar, James H.↗