Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “component performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Logic in Memory Emulator

Logic in Memory Emulator (LiME) is a hardware/software tool specially designed for memory system evaluation and experiment. Emerging memories display a wide range of bandwidths, latencies, and capacities, making it challenging for the computer architect to navigate the design space of potential memory configurations, and for the application developer to assess performance implications of using such memories. With the LiME framework, architectural ideas can be prototyped in great detail yet with sufficient performance to support realistic evaluation on long running applications. LiME consists of two fundamental components: 1) the hardware and OS infrastructure for the emulator, and 2) a suite of benchmark applications to assist in characterizing the performance of current and future computer architectures. Some of the applications have been collected from other open source projects. Uses: Logging, replay and analysis of an application's memory behavior Evaluate impact of emerging memory technology on application performance. Emulate complex memory interactions in whole applications orders of magnitude faster than software simulation. Emulate acceleration hardware co-located with the memory subsystem. Features: Capture and log external memory accesses to a separate off-chip memory device without affecting application execution. Memory traces include the address, length, timestamp, and optionally the data for each transaction. Captured trace data can be saved to an SD card for off-line analysis. Configure a wide range of memory latencies in sub-nanosecond increments that encompass highbandwidth and storage class memories. Specify regions of interest (ROI) in applications to reduce the amount of trace data captured for analysis. Currently supports execution on Xilinx Zynq SoC which integrates an ARM processor with FPGA logic on a single device. Applications can be run under Linux or in bare metal mode on the ARM cores.

Jain, AbhishekK↗
DOE OSTI2020

Electrically conductive carbon fiber layers as lightning strike protection for non-conductive epoxy-based CFRP substrate

A large amount of electrically conductive fillers is needed to enhance a Carbon Fiber Reinforced Plastics (CFRP) electrical conductivity enough to withstand lightning strikes of peak currents. However, such large alien constituents hamper the inherent good mechanical properties of CFRP structures. In this work, a solution has been proposed to retain both desired properties in a CFRP laminate. Layer-wise hybrid laminate has been demonstrated as a solution for lightning strike protection of Carbon Fiber Reinforced Plastics (CFRP). Top few layers of a hybrid laminate are prepared using electrically conductive polymer-based resin (CF/C-POLY) to provide effective dissipation of lightning current while epoxy-based CFRP substrate (CF/Epoxy) provides the main structural strength. An insulating adhesive layer is used to bond CF/C-POLY and CF/Epoxy to prepare the laminate. The hybrid laminates were tested for their effectiveness against lightning strikes. Laminates were struck by modified lightning waveform of component A with peak current of -14 kA and -40 kA. The performance of the laminates against lightning strike were evaluated using high speed camera, high-speed and thermal camera. It is found that CF/C-POLY layer successfully defended the main structural component i.e. CF/Epoxy from lightning direct damage.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Automation of FARM from Alpha Phase to Beta Phase

Integrated energy systems (IES) combine different energy technologies in synergistic ways to achieve a more secure and economical energy supply. The RAVEN-based HYBRID framework and the RAVEN plugin for grid and capacity optimization (HERON) are used to find the optimal installed capacity and the optimal economical dispatch of each component of the IES, by respecting the limits on the production variables and the corresponding rates of variation (explicit constraints). Besides, there are other process variables whose evolution needs to be bounded to avoid damaging the components (e.g., condensers, heat exchangers, steam generators, etc.) or degrading the process efficiency (e.g., electrolysis in the hydrogen production process). To avoid violating these latter limits (implicit constraints), a proof-of-concept HERON validator based on Feasible Actuator Range Modifier (FARM-Alpha) was developed by Argonne National Laboratory in January 2021. This FARM-Alpha validator calculates the evolution of process variables on whom the implicit constraints are placed, and then provides feedback to HERON dispatcher to adjust the power setpoints of three IES components, i.e., Balance of Plant, Secondary Energy Source, and Thermal Energy Storage, so as to meet both the explicit and implicit constraints. FARM-Alpha was designed to assess the performance of FARM as a HERON validator only, i.e., the list of components and implicit operational constraints were hard-coded within the source code. The lack of flexibility of the corresponding software structure does not allow the deployment in production environment. This report describes the development and the implementation of an enhanced version of the FARM-based validator (FARM-Beta), which ensures more flexibility for the end user in modeling multiple IES configurations and scenarios. Several test cases of the power dispatch problem were then selected to demonstrate the capabilities offered by FARM-beta. The test cases illustrate the efficiency of the closed-loop optimization scheme and the capability to calculate set-point trajectories satisfying both explicit and implicit constraints.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

New machine protection system at the Spallation Neutron Source – design process and performance analysis

A New Machine Protection System (MPS) at the Spallation Neutron Source (SNS) was developed and implemented on µTCA-based hardware platforms. The system monitors more than 2500 field inputs and shuts off the beam within 10 µs if adverse events occur. We will present system level design process of various firmware and software components as well as the system integration into EPICS environment. The performance analysis of the MPS after two SNS run cycles will also be presented.

Bobrek, Miljko [ORNL] (ORCID:0000000332763451)↗
DOE OSTI2022

Predictive Tools for Customizing Heat Treatment of Additively Manufactured Aerospace Components

Laser-bed powder fusion (LBPF) additive manufacturing is increasingly being used to produce components of complex geometries using the Ni-base superalloy Inconel 718. The composition and the microstructure of the alloy are currently well optimized for wrought components made using conventional manufacturing processes such as rolling, forging, extrusion, etc. The attractive mechanical properties of the alloy result from the underlying austenitic matrix with fine equiaxed grains, and a high density and uniform distribution of the precipitation hardening phase, γ". Heat treatment steps such as homogenization, solutioning and aging are well documented for the wrought alloy. However, when the same wrought alloy compositions are used for the additive manufacturing (AM) processes, the asprocessed microstructure is significantly different, because of the different thermal history associated with LBPF, including rapid solidification and multiple temperature excursions that lead to multiple re-melting and reheating in the solid state. Rapid solidification introduces potential non-equilibrium effects at the moving solid-liquid interfaces that impact the extent of solute segregation, as well as the morphology of the dendritic grains that form. In order to recover the target mechanical properties, AM components have to undergo post-process heat treatments. However, such heat treatments have to be custom designed for the AM process and the component geometry because of the expected vast differences in the microstructure at various locations of a component with complex geometry. The homogenization and precipitation steps should be optimized for the component so that target mechanical properties can be obtained throughout the part. The objective of this research is to utilize High Performance Computing in phase field simulations of microstructure evolution during post-processing of AM components. The physics-based modeling will be beneficial in reducing the experimental effort required for heat treatment process selection, optimization, and certification, thus leading to a significant reduction in energy consumption for AM and post-processing heat treatment. The optimization study will help identify heat treatments steps that are critical for development of a final desired microstructure with the minimum energy input. This combined with shortening of the production cycle (time-to-market) by reducing the number of failed parts (property targets), and reduction in the number of iterations for process optimization, will enable 30-40% savings in the energy costs. Phase field simulations of the degree of homogenization and the effect of local matrix composition on the nucleation and growth of competing precipitating phases were performed using the Microstructure Evolution Using Massively Parallel Phase Field Simulations code developed in-house at the Oak Ridge National Laboratory. The simulations were able to successfully capture the kinetics of nucleation and growth, and morphologies of various precipitating phases as a function of local matrix compositions and composition gradients characteristic of local microstructures arising from location-dependent variations in the thermal conditions. Future work will involve extending the simulations to a length scale consisting of multiple dendrites, so that the effect of homogenization on the coarsening of the dendrites can be simulated and used as an additional input to the optimization of the heat treatment process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Grand challenges in the design, manufacture, and operation of future wind turbine systems

Abstract. Wind energy is foundational for achieving 100 % renewable electricity production, and significant innovation is required as the grid expands and accommodates hybrid plant systems, energy-intensive products such as fuels, and a transitioning transportation sector. The sizable investments required for wind power plant development and integration make the financial and operational risks of change very high in all applications but especially offshore. Dependence on a high level of modeling and simulation accuracy to mitigate risk and ensure operational performance is essential. Therefore, the modeling chain from the large-scale inflow down to the material microstructure, and all the steps in between, needs to predict how the wind turbine system will respond and perform to allow innovative solutions to enter commercial application. Critical unknowns in the design, manufacturing, and operability of future turbine and plant systems are articulated, and recommendations for research action are laid out. This article focuses on the many unknowns that affect the ability to push the frontiers in the design of turbine and plant systems. Modern turbine rotors operate through the entire atmospheric boundary layer, outside the bounds of historic design assumptions, which requires reassessing design processes and approaches. Traditional aerodynamics and aeroelastic modeling approaches are pressing against the limits of applicability for the size and flexibility of future architectures and flow physics fundamentals. Offshore wind turbines have additional motion and hydrodynamic load drivers that are formidable modeling challenges. Uncertainty in turbine wakes complicates structural loading and energy production estimates, both around a single plant and for downstream plants, which requires innovation in plant operations and flow control to achieve full energy capture and load alleviation potential. Opportunities in co-design can bring controls upstream into design optimization if captured in design-level models of the physical phenomena. It is a research challenge to integrate improved materials into the manufacture of ever-larger components while maintaining quality and reducing cost. High-performance computing used in high-fidelity, physics-resolving simulations offer opportunities to improve design tools through artificial intelligence and machine learning, but even the high-fidelity tools are yet to be fully validated. Finally, key actions needed to continue the progress of wind energy technology toward even lower cost and greater functionality are recommended.

17 WIND ENERGY↗
DOE OSTI2023

Application of Principal Component Analysis to Electrochemical Reprocessing PM and NMAC

In this report, data from an electrorefiner (ER) for nuclear fuel reprocessing is evaluated for process monitoring (PM) conclusions. This data comes from tests performed at the Idaho National Laboratory in 2022. Multivariate approaches utilizing methods of Principal Component Analysis (PCA) is applied. This is based off established work in process monitoring for fault detection in industrial facilities. This report will discuss the background, methods, and results of the application and some of the conclusions and applications that can be drawn from them. PCA is applied to two different electrorefiner (ER) operations that occurred at Idaho National Laboratory between August and October 2022. The first operation occurred with little incident while the second had several noted faults in the equipment in operational logs. The data from the first run was used to train the data for “normal” operations and applied to both sets of data to determine when operations were in an “off-normal” condition and identify where the fault occurs through PCA. PCA was able to identify off-normal events and identify the cause for off-normal operations. These identified off-normal events matched with the events and their causes in the operational logs. However, small amounts of variance in the data led to false detection of “off-normal” events. Thus, careful selection of training data and a-posteriori conclusions based off operator assessments will both be required for application of PCA to PM applications. This work demonstrated that multivariate approaches and latent variables are applicable to pyroprocessing PM applications and can be further expanded in future work as quality variables such as salt concentration from sensors and sampling become available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Boosting electrochemical reaction and suppressing phase transition with a high-entropy O3-type layered oxide for sodium-ion batteries

Complex phase transitions induced by interlayer slides in layered cathode materials lead to poor cycling stability and rate capability for sodium-ion batteries. Herein, we design and prepare a new six-component high-entropy oxide (HEO) layered cathode O3–Na(Fe 0.2 Co 0.2 Ni 0.2 Ti 0.2 Sn 0.1 Li 0.1 )O 2 to enable highly reversible electrochemical reaction and phase-transition behavior. The HEO cathode exhibits good cycling performance (capacity retention of ~81% after 100 cycles at 0.5C) and outstanding rate capability (capacity of ~81 mA h g –1 at 2.0C) due to the higher sodium diffusion coefficient (above 5.75 × 10 –11 cm 2 s –1 ) than most reported O3-type cathodes. Moreover, the high-entropy cathode has superior compatibility with the hard carbon anode and delivers a specific capacity of 90.4 mA h g –1 (energy density of ~267.5 W h kg –1 ). Ex situ X-ray diffraction proves that the high-entropy designing effectively suppresses the intermediate phase change to achieve reversible O3–P3 phase evolution, and in turn stabilizes the layered structure. X-ray absorption spectroscopy and Mössbauer spectrum of 57 Fe suggest that Ni 2+ /Ni 3.5+ , Co 3+ /Co 3.5+ , and part of Fe 3+ /Fe 3.5+ redox reaction contribute the charge compensation. Finally, the enhanced performance can be attributed to the disordered distribution of multi-component transition metals in HEO suppressing the ordering of electric charges and sodium vacancies, thereby inhibiting the interlayer slide and phase transition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Detecting anomalous SRF cavity behavior with unsupervised learning

We present an unsupervised learning framework for detecting anomalous superconducting radio-frequency (SRF) cavity behavior at the Continuous Electron Beam Accelerator Facility (CEBAF), emphasizing its initial performance and effectiveness. Key to the system’s success was the development of data acquisition systems (DAQs) that capture fast-sampled, information-rich signals, essential for detecting transient effects. The approach involves creating daily cavity-specific models using principal component analysis to handle variations in rf signal behavior and mitigate performance degradation from data drift. This unsupervised method eliminates the need for expensive labeling by continuously updating models with recent data. Deployed and operational for 3 months before a scheduled shutdown, the system successfully identified several issues with DAQ signals, confirming its effectiveness. Despite access to only a fraction of CEBAF’s SRF cavity signals, the framework efficiently detected several instances requiring intervention, demonstrating a significant improvement over traditional, labor-intensive methods of manual plot inspection. Published by the American Physical Society 2025

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Development and performance of INCONEL® alloy 740H® seam-welded piping

INCONEL® alloy 740H® is an age-hardenable nickel-based alloy approved for pressure vessels and piping within ASME Section I, VIII, and B31.1. Currently, the code applies a weld strength reduction factor (WSRF) of 0.7 to the allowable stresses for longitudinal seam welds in the time dependent creep regime. In this work, a full-scale seam weld was successfully produced using typical industrial practices. The component was solution heat-treated and aged after fabrication to improve the performance of the weldment. Tensile, bend, impact, and low-cycle fatigue tests showed the component met all the specification requirements and elevated temperature properties were within base metal expectations with failures predominately in the weld metal. Long-term creep tests, including large samples more representative of the entire weldment, were fabricated and tested to times in excess of 10,000 h at multiple temperatures. Analysis of the creep data supports a WSRF of 0.9 for the solution annealed + aged weldments in contrast to the WSRF of 0.7 currently applied to welded + aged weldments. Metallurgical analysis shows that the solution annealing causes recrystallization of the weld metal and reduces the chemical compositional and microstructural gradients in the weldments resulting in acceptable short-term performance. In long-term creep, evidence for coarsened zones in the weldments due to discontinuous coarsening reactions were identified as the mechanism leading to accelerated creep damage formation in the weld metal and sample failure.

14 SOLAR ENERGY↗
DOE OSTI2020

CyDER: A Cyber Physical Co-simulation Platform for Distributed Energy Resources in Smartgrids

The CyDER project aimed at developing an open-source, modular and scalable co-simulation platform for power grids with large shares of Distributed Energy Resources (DERs). The project partners are the Lawrence Berkeley National Lab (LBNL), Lawrence Livermore National Lab (LLNL), PG&E, SolarCity, and ChargePoint. The prime recipient is LBNL; SolarCity and ChargePoint were partners for the project’s first two years. Increased DER integration introduces a number of challenges in power grid operation including a more dynamic interaction between the transmission grid and distribution grids, and increased modeling complexity. Although specialized software exists to precisely model different components of the power system, it is far from trivial to integrate all various models and perform a holistic simulation. Instead of replicating all models in a common simulation program, a commonly accepted approach to tackle this model diversity is to couple third-party simulators and models through a co-simulation platform that coordinates information exchange among the various components. Following this line of research, this project’s objective was to develop a co-simulation platform based on a widely accepted industrial standard called Functional Mockup Interface (FMI). Within this process, the project developed models compliant with the FMI standard, called Functional Mockup Units (FMUs), and used them to perform various operational and planning power system analyses. Relying and building upon an industrial standard is the main differentiation of this project compared with previous or parallel efforts in the co-simulation area. Particular emphasis was put on delivering software utilities to facilitate setting up and running co-simulations by end-users. Furthermore, a strong aspect of this project is demonstrating that co-simulation techniques can be used to perform Hardware-in-the-Loop (HIL) simulations that couple software components (e.g., simulated models) with hardware components (e.g., real devices such PV systems and batteries). The long-term goal of CyDER project is to help establish FMI as a powerful standard for co-simulation and promote adoption by electric utilities and other interested stakeholders. The main accomplishments of the project include the development of several FMUs including distribution and transmission grid models, PV inverters with Volt/Var/Watt controllers, batteries, and predictive optimal controllers. Additionally, a unique software package was developed, called SimulatorToFMU, which is capable of exporting any Python-driven simulator or Python script as an FMU. This is an important contribution towards establishing FMI as one of the main co-simulation standards, because more and more third-party programs for sub-system modeling and simulation are delivered with Python APIs. The CyDER platform was used to perform PV hosting capacity analyses in real utility feeders with and without smart inverter controls, battery storage, and EV charging. Smart inverter controls include conventional Volt/Var/Watt controls for reactive power support and active power curtailment, but also predictive controls that optimize the charging and discharging profile of the battery connected on the DC side in order to minimize the customer’s economic benefit. Finally, an important result of this project is delivering an experimental setup that consists of residential-scale PV inverters with battery storage, a real-time grid simulator with an ideal voltage source as grid emulator, and micro Phasor Measurement Units (PMUs). All these components and additional software modules are coupled to one another using the FMI standard and can be co-simulated with the CyDER platform.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Reconfigurable Network Slicing Orchestration in Network Function Virtualization Compatible Operational Technology Environment

The ongoing transition to Industry 4.0, which is characterized by increased inter-connectivity of cyber-physical systems, requires having time-sensitive, high throughput, and secure transfer of critical data in industrial sites. In this context, network slicing emerges as a critical tool to ensure timely data delivery by provisioning the network resources to cater to specific applications’ requirements and mitigating potential cyber attacks. To address these challenges, this paper aims to tackle two key questions essential for the successful implementation of network slicing in industrial environments. First, it investigates architectural considerations for developing a network infrastructure capable of supporting network slicing functionalities effectively. The proposed approach significantly improves deployment efficiency over traditional manual configurations. Second, it delves into the automated orchestration process, elucidating the steps and components involved in transitioning from a static network management approach to dynamically leverage network function virtualization schemes for creating network slices in ad-hoc manner. The system demonstrates high throughput suitable for production-level solutions and maintains exceptionally low latency, making it ideal for ultra-reliable low-latency communications. Even with increased network demands, the system remains stable, with effective Quality of Service (QoS) management, ensuring reliable performance under varying conditions. The proposed architecture outlines the necessary components, services, and communication protocols required for a production-level orchestrator for network segmentation in SCADA environments.

Rodiles Delgado, Brian G.↗
DOE OSTI2023

PhytoOracle: Scalable, modular phenomics data processing pipelines

As phenomics data volume and dimensionality increase due to advancements in sensor technology, there is an urgent need to develop and implement scalable data processing pipelines. Current phenomics data processing pipelines lack modularity, extensibility, and processing distribution across sensor modalities and phenotyping platforms. To address these challenges, we developed PhytoOracle (PO), a suite of modular, scalable pipelines for processing large volumes of field phenomics RGB, thermal, PSII chlorophyll fluorescence 2D images, and 3D point clouds. PhytoOracle aims to ( i ) improve data processing efficiency; ( ii ) provide an extensible, reproducible computing framework; and ( iii ) enable data fusion of multi-modal phenomics data. PhytoOracle integrates open-source distributed computing frameworks for parallel processing on high-performance computing, cloud, and local computing environments. Each pipeline component is available as a standalone container, providing transferability, extensibility, and reproducibility. The PO pipeline extracts and associates individual plant traits across sensor modalities and collection time points, representing a unique multi-system approach to addressing the genotype-phenotype gap. To date, PO supports lettuce and sorghum phenotypic trait extraction, with a goal of widening the range of supported species in the future. At the maximum number of cores tested in this study (1,024 cores), PO processing times were: 235 minutes for 9,270 RGB images (140.7 GB), 235 minutes for 9,270 thermal images (5.4 GB), and 13 minutes for 39,678 PSII images (86.2 GB). These processing times represent end-to-end processing, from raw data to fully processed numerical phenotypic trait data. Repeatability values of 0.39-0.95 (bounding area), 0.81-0.95 (axis-aligned bounding volume), 0.79-0.94 (oriented bounding volume), 0.83-0.95 (plant height), and 0.81-0.95 (number of points) were observed in Field Scanalyzer data. We also show the ability of PO to process drone data with a repeatability of 0.55-0.95 (bounding area).

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Capturing Historic Reliability Performance Through Graph Databases: A Model Based System Engineering Approach

With the goal of improving the performance and reliability of high dependable technological systems such as nuclear power plants, advanced monitoring and health management systems are employed to inform system engineers on observed degradation processes and anomalous behaviors of assets and components. This information is captured in the form of large amount of data which can be heterogenous in nature (e.g., numeric, textual). Such large data availability poses challenges when system engineers are required to parse and analyze them in order to track historic reliability performance of assets and components. This paper tackles directly this challenge by providing means to organize data in the form of a graph: a knowledge graph. The presented approach distinguish itself from current knowledge graph-based methods by the fact that model-based system engineering (MBSE) models are used to “put data into context”. In particular, MBSE models are used as skeleton of a knowledge graph; numeric and textual data elements, once processed, are associated to MBSE model elements. Thus, a knowledge graph captures both system architecture (though MBSE models) and health/performance data. Such feature opens the door to new data analytics methods designed to identify causal relations between observed phenomena.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Mochi: Composing Data Services for High-Performance Computing Environments

Technology enhancements and the growing breadth of application workflows running on high-performance computing (HPC) platforms drive the development of new data services that provide high performance on these new platforms, provide capable and productive interfaces and abstractions for a variety of applications, and are readily adapted when new technologies are deployed. The Mochi framework enables composition of specialized distributed data services from a collection of connectable modules and subservices. Rather than forcing all applications to use a one-size-fits-all data staging and I/O software configuration, Mochi allows each application to use a data service specialized to its needs and access patterns. This paper introduces the Mochi framework and methodology. The Mochi core components and microservices are described. Examples of the application of the Mochi methodology to the development of four specialized services are detailed. Finally, a performance evaluation of a Mochi core component, a Mochi microservice, and a composed service providing an object model is performed. The paper concludes by positioning Mochi relative to related work in the HPC space and indicating directions for future work.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

UNCERTAINTIES FOR IN-REACTOR TESTING OF TRITIUM LOADED GETTERS WITH TEMPERATURE CONTROL

The fourth experiment in TPBAR Materials Irradiation Separate-Effects Test (TMIST) series (TMIST-4) is planned to experimentally determine the effect of neutron irradiation on the equilibrium vapor pressure of tritium over a tritium loaded Nickel-Plated Zirconium (NPZ) getter in a simulated TPBAR service environment. This pressure will be used to estimate the tritium permeation rate. In the thermal design in the TMIST-4, two evaluations are required. 1) The cladding temperature is calculated to estimate the feasibility of detecting potential irradiation enhancement of the partial pressure for an NPZ getter. This work is required to obtain a precise cladding temperature for measurement of a low tritium partial pressure. This work has been completed and indicated that the required/target cladding temperatures based on the TMIST-4 test plan can be satisfied under the test condition range by modifying the capsule component shapes and inserting a thermally conductive metal sleeve. 2) The evaluation of uncertainties associated with the test design and operation is performed. This includes fabrication tolerances, and power and nuclear operating conditions. These factors will impact the component temperatures inside capsules and resulting the tritium partial pressure. The tritium permeation rate is a function of temperature and tritium partial pressure. The prediction of tritium permeation rates affects the feasibility of obtaining measurement resolutions required to reach reasonable conclusion for potential irradiation enhanced performance. This work will investigate the uncertainties.

TTP, TPBAR, TMIST-4, TPBAR Materials Irradiation S↗
DOE OSTI2025

Ultra-high temperature testing and performance of L-PBF C103

Additive Manufacturing (AM) of refractory alloys is gaining traction as a materials processing route for components subject to extreme temperature environments. Due to the low oxidation resistance of refractory alloys, novel methods for evaluating their elevated temperature performance must be developed. In this work, a Gleeble® 3800 thermomechanical load frame was modified to evaluate the mechanical properties of laser powder bed fusion (L-PBF) consolidated niobium alloy C103 ranging from room temperature (RT) to 1400 °C. The fixturing and sample geometry were designed to accommodate Joule heating and prevent damage to the test chamber. Oxidation of the samples was minimized via testing in vacuum level of 1E-5 Torr. Ultimate tensile strength (UTS), yield strength (YS), elongation, and strain-hardening behavior were determined as a function of temperature. L-PBF C103 presented an average UTS of ∼650 MPa and over 25 % elongation at RT. Above RT, the UTS and YS dropped then leveled off from 500 °C to 1000 °C with values ranging from ∼400 MPa to ∼460 MPa, which is consistent with dynamic strain aging observed in this class of alloys. The strength rapidly declined after 1200 °C to ∼150 MPa at 1400 °C. Fractography indicated ductile fractures for the C103 at all test temperatures, and Electron Backscatter Diffraction (EBSD) analysis revealed a textured microstructure and the presence of dynamic recrystallization within the necked region of the sample tested at 1400 °C.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Innovative Method for Reliable Measurement of PEM Water Electrolyzer Component Resistances

Understanding the sheet resistance of porous electrodes is essential for improving the performance of polymer electrolyte membrane (PEM) water electrolyzers and related technologies. Despite its importance, existing methods often fail to provide reliable and comprehensive data, especially for porous materials with complex morphologies and non‐uniform thicknesses. This study introduces a robust and straightforward method for determining the sheet resistance of porous electrodes using a novel probe concept based on industrial printed circuit board (PCB) technology. This probe measures resistance across ten distances, ranging from 250 µm to 2500 µm, enabling local mapping of resistance. The study focuses on the sheet resistance of key components in PEM water electrolyzers, including the gas diffusion layer (GDL), porous transport layer (PTL), and catalyst layers deposited on a membrane. Additionally, an image‐processing‐based method is presented to obtain the thickness distribution of the studied catalyst layers, facilitating a detailed analysis of the electrical in‐plane resistivity with thickness variations. Overall, this methodology has the potential to expedite material integration and bridge the gap between electrode engineering and single‐cell testing, thereby advancing the development of PEM water electrolyzers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗