Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Near-Net-Shape Hot Isostatic Press Manufacturing Modality for sCO2 CSP Capital Cost Reduction

Through this DOE funded 3.5-year research project, feasibility of fabricating supercritical carbon dioxide (sCO2) turbine components by powder metallurgy (PM) based near-net-shape (NNS) hot isostatic pressing (HIP) was demonstrated in a turbine nozzle ring, a turbine casing with Haynes 282 powder, and a bimetallic pipe with Haynes 282 and SS415 powder. As-HIP microstructure of various powders and HIP processing conditions was studied to downselect a condition for the prototype components. Tensile strength and low cycle fatigue (LCF) capability of PM HIP 282 was found to be superior to cast 282, despite a debit in creep stress capability that could be mitigated by component design modification. Near-Net-shape with minimal post machining was achieved by modeling the non-uniform shrinkage during HIP cycle and designing the HIP tooling to meet dimensional targets. The prototypes of turbine nozzle ring and bimetallic pipe were successful in achieving overall dimension, microstructure, and properties, despite dimensional tolerance affected by chemical milling rate. The prototype of a 1700lbs turbine casing was partially successful in achieving dimension, microstructure in as-HIP state, and providing consistent mechanical properties, however, cracking issue during post heat treatment required further investigation. The estimated manufacturing cost using NNS HIP was a ~50% reduction compared to forging with extensive machining, which translated into ~$100/kWe CAPEX cost reduction for concentrated solar power (CSP) power block.

14 SOLAR ENERGY↗
DOE OSTI2024

2D IR Microscopy—Technology for Visualizing Chemical Dynamics in Heterogeneous Environments (Final Technical Report)

The primary focus of this project was the design, prototype, and demonstration of a 2D IR microscope. The start date of this project was July 15, 2016 and the project end date was July 14, 2022. In the early years of this project our team designed, prototyped, and completely integrated a homebuilt microscope head with our high-repetition rate 2D IR spectrometer. Once in place our research team focused on characterizing the 2D IR microscope and using it to investigate model systems relevant to energy technologies. As part of this process, we identified two initial chemical systems to use to further develop 2D IR imaging modalities. The first chemical system developed was a room temperature ionic liquid (RTIL) electrolyte system and the second chemical system was a mixture of carbonates and salts developed as a battery electrolyte system. The completion of this project resulted in the full characterization of chemical dynamics in a bulk RTIL system and the demonstration of 2D IR imaging across the RTIL cast as a microdroplet in silicon oil. In addition, we explored the liquid structures and dynamics of organic carbonate mixtures from the vantage point of the vibrational probe, methyl thiocyanate. By the end of the project, we had moved toward in-depth studies of the organic carbonate mixtures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Internal Material Melting Development Progress [Slides]

Slides for an AFC workshop giving a brief overview of the current status of Bison code development for correct energy balance of melting material. The slides provide background information of why the development is needed. The planned approach of casting the energy balance as a change in enthalpy is described. Status of current code additions is outlined. Extra slides are provided with more mathematical details of the approach derivation and verification.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Composite PEMs from Electrospun Crosslinkable Poly(Phenylene Sulfonic Acid)s (Final Technical Report)

The main objective of this project is to fabricate and demonstrate superior fuel cell performance of an electrospun composite all-hydrocarbon, non-PFSA membrane. The project builds on two earlier, DOE-funded studies demonstrating high proton conductivity, even at very low humidity of crosslinkable poly(phenylenesulfonic acid), cPPSA, solution cast films, and high durability of electrospun perfluorosulfonic acid (PFSA) composite membranes. Most project milestones were fully met but the best membrane conductivity and fuel cell performance were obtained with membranes that did not contain electrospun sulfonated polyphenylene, as initially planned. Instead, an excellent performance was achieved with membranes fabricated by pore-filling, either with electrospun poly(phenyl sulfone) scaffolds or with commercial, expanded polytetrafluoroethylene scaffolds. Fuel cell testing demonstrated performance better than that of Nafion 211 or Nafion XL, particularly at lower cell humidification levels with significantly lower hydrogen crossover. No accelerated stress testing was performed, due to the initial numerous difficulties with controlling the copolymerization reaction, which took excessive amount of time to overcome. Potential scale-up of the proposed composite membrane technology can aid in boosting the fuel cell power output and simplification of the cell hydration system.

08 HYDROGEN↗
DOE OSTI2024

Near Net Shape Workshop Report

In 2021, President Biden issued Executive Order (EO) 14017, spurring the federal government to build more secure and diverse U.S. supply chains, including energy supply chains, to ensure economic prosperity and national security (White House 2021). In response to EO 14017, the U.S. Department of Energy (DOE) published America’s Strategy to Secure the Supply Chain for a Robust Clean Energy Transition (Igogo 2022) to outline the challenges and opportunities facing the energy supply chain along with key strategies to secure America’s position as a clean energy superpower in the years and decades to come. The expansion of domestic manufacturing capabilities is identified as one of the common risks and vulnerabilities for which DOE should develop comprehensive strategies to secure supply chains for the clean energy transition. The report states that “examples of manufacturing capabilities of concern include … large iron and steel castings for wind turbines, hydropower turbines, and nuclear reactor components.”

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Highly Efficient Vacuum Smelting of Aluminum

The goal of this SBIR project was to develop and demonstrate an innovative aluminum smelting technology that will significantly increase the range of aluminum alloys that can be manufactured from recycling of scrap aluminum. This will result in reduction of need for primary aluminum with corresponding 95% energy and CO 2 emission benefits. The proposed melting of pre-sorted aluminum alloys using UHV’s patented high throughput sorter funded by ARPA-E METALS program in an energy efficient vacuum furnace avoids the typical 5% metal loss due to oxidation of molten metal. In addition, pre-sorting scrap into different categories (cast, wrought, extrusion and aerospace) allows lower cost production of high value aluminum alloys without the need for adding alloying elements to primary aluminum. During this SBIR project, pure aluminum and several different commercial alloys were procured and melted in a laboratory furnace in vacuum, CH4 and air environments. The slag and oxidation formation were measured using weight and cross-sectional scanning electron microscope. The results otained were mixed and did not show direct correlation between furnace pressure and oxidation. We believe that the results were tainted due to small furnace size and non-uniformity of oxidation layer. A more thorough investigation is required to prove the advantages of vacuum smelting which could not be performed due to the COVID-19 lockdowns during this project. The theoretical fact remains that in the absence of oxygen in the furnace, there should be no oxide after melting, however the team could not prove it experimentally, and thus decided to dis-continue the project.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrochemically driven carbon dioxide separation

This project explored the viability of a Ni(OH) 2 based hydroxide exchange membrane carbon capture (HEMCC) device for direct air capture. It is built off an H 2 fuel cell based HEMCC previously developed in the Yushan Yan group at University of Delaware. Taking the same membrane-based, electrochemically driven pH gradient concept, similar flux performance was able to be seen in the Ni(OH) 2 system as the H 2 system when using comparable current densities. The project produced two types of membrane electrode assemblies (MEA). The first was a traditional MEA with two electrodes and a membrane, the second was a flow-through membrane MEA. Consistent performance was achieved with the traditional MEA with an energy cost of 1.1 MWh∙ton -1 and flux of 82 kg∙m -2 ∙yr -1 . This was the most stable of the two designs. This project investigated strategies to improve performance with a flow-through membrane design. Two designs were made, one with a cast phase inversion membrane, and one with powdered membrane layer. The template phase inversion membrane achieved low pressure drop but had performance limitations due to a skin layer of membrane limiting CO 2 gas transport. The powdered membrane layer had better performance but higher pressure drop. Finally, using the powdered membrane, commercial battery materials were able to be used in order to achieve higher flux. This showed that the flow through membrane design does have the capability to overcome flux inefficiencies in the traditional MEA. Moreover, the process design of the system is proposed and given in this project. The process mass and energy balances were calculated for a reference plant of 1000 t/yr CO 2 capture, which contains several subsystems, e.g. air processing subsystem, electrical subsystem, and CO 2 purification and compression subsystem is designed and evaluated. Based on our calculation, When the power consumption for stack is 1 MWh t -1 CO 2 , Additional 382 kWh t -1 CO 2 will be consumed by other subsystem of the plant, i.e. The total power consumption of 1.38 MWh t -1 CO 2 , lower than the final milestone of 1.5 MWh t -1 CO 2 in this project.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Equitable Energy Transition Planning in Holyoke, Massachusetts: A Technical Analysis for Strategic Gas Decommissioning and Grid Resiliency

Buildings account for 30% of the emissions in Massachusetts and are the largest source of emissions in the United States, along with transportation. Pipeline-delivered methane gas is the dominant heating source in Massachusetts, representing 51% of heating in the state. The current gas network in Massachusetts and across many other US states is aging, a relic of the coal gas era, with thousands of miles of cast iron and unprotected steel pipes that are considered leak prone. Even newer plastic pipes are subject to degradation and in need of replacement, an upgrade that averages $2.8 million per mile of pipeline replacement across investor-owned utilities in Massachusetts.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Specification of EBR-II Fabricated Fuel Diameter Data

All IFR EBR-II fuel pins were fabricated at one of the related fuel fabrication facilities at Argonne National Laboratory-West, at the EBR-II site [1]. U-Pu-Zr experimental pins were fabricated at the Experimental Fuels Laboratory (EFL), which was established in April of 1984 after the positive acceptance of the IFR concept, while the U-Zr experimental pins were fabricated at the Fuel Manufacturing Facility (FMF), along with the driver fuel pins [2]. The injection-casting fabrication process is described in detail in ref [1]. All the fuel pins that were loaded into EBR-II were examined after fabrication to ensure that they met the design dimensional requirements and tolerances prior to assembly. Fuel slug diameter was measured with either a laser profilometer (at FMF) or a hand micrometer (at EFL), at a minimum of 1-inch intervals over the length of the fuel slug, as shown in Figure 1 [2]. In all cases the average fuel diameter is reported, in some cases with additional summary statistics (e.g., minimum, maximum), and in rare cases the complete record of axially-varying fuel diameters is available. It should be noted that in cases where axial varying data is available, in general the orientation of the slug was not recorded or carried over to loading of the pin, so a diameter measurement at the bottom of the fabricated slug does not necessarily correspond to the bottom of the loaded slug, as it may have been loaded in either orientation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

High Temperature Tensile Testing of Molybdenum Before and After Exposure in Flowing He at 600°C to 1000°C

ORNL supported NorthStar Medical Radioisotope’s accelerator-based concept to produce the medical isotope molybdenum-99 (Mo-99). The Mo targets are expected to experience in the accelerator temperature ranging from 200°C to 1000°C, and previous studies have demonstrated the embrittlement of Mo targets at room temperature when exposed to impure He at 800 to 1000°C. The goal of this project was to evaluate potential embrittlement at temperature ranging from 600°C to 1000°C for three Mo materials exposed at the same temperatures for 100h in high purity He (O 2 < 5ppm (µl/l)) with a flow rate of ~1m/s. Enriched Mo-100 (aMo) and conventional pressed and sintered Mo (UHP) disks were provided by NorthStar while low carbon arc cast rolled Mo, fabricated at ORNL, was used for comparison. The as fabricated rolled Mo exhibited superior tensile strength due to the alloy very fine grain size with limited ductility except at 1000°C with the elongation at rupture reaching 30%. The UHP Mo disks showed the lowest strength but highest ductility at 20-1000°C with significant strain hardening during tensile testing. The ductility of the aMo material was quite low at all temperatures due to a high density of voids at grain boundaries. Significant embrittlement of the aMo material was observed after exposure at 600°C to 1000°C, most likely because of oxygen diffusion and segregation at grain boundaries. No embrittlement was observed for the UHP Mo material, with excellent elongation at rupture for some of the specimens oxidized in He and tested at 600-1000°C. Significant variation in ductility from one UHP Mo specimen to another was, however, measured, both in the as fabricated and He-oxidized conditions. The rolled Mo was not affected by oxidation in He at 800°C, but a decrease in strength and increase in ductility was observed at 1000°C, likely due to the material recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

BERT Non-Destructively Probes the Microstructure of Dissimilar Welds [Poster]

Energy-resolved neutron imaging (ERNI) utilizes contrast provided by diffraction. Microstructure with >100µm grains as in cast, annealed or welded materials is difficult to characterize by X-ray or electron-based methods $\Rightarrow$ Well-suited for neutron Bragg-edge radiography. BERT was applied to dissimilar welds of Inconel on steel produced by additive manufacturing. Viewing the sample at time-of-flight/energy/wavelength where a single grain orientation dominates the attenuation allows to map grain orientations. Similarly to electron-backscatter diffraction (EBSD) but on cm length scales and through-thickness. Combined with texture measurements on the HIPPO instrument, identifying major grain orientations, 2D and 3D grain orientation maps are feasible. Results can guide development of thermo-mechanical treatment avoiding or introducing such microstructures, characterize dissimilar welds, interpretation of acoustic signals for quality control, guide destructive examination with X-rays/electrons, or provide data for codes predicting such microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced Fabrication Techniques of Metal Hydrides for Science and Technology Applications (Abbreviated Final Report)

Lithium Hydride (LiH) atomic properties make it an excellent candidate for thermal energy storage, hydrogen storage, and nuclear reactor technology. High Energy Density (HED) experiments on LiH at the National Ignition Facility (NIF) can also provide critical Equation of State (EOS) and Hugoniot data. Density requirements for LiH vary per application and therefore physical and structural requirements for LiH are non-uniform. Historical production of LiH relies on casting processesthat are limited by density and grain-size control, which leads to unfavorable machinable characteristics. LiH manufacturing is further hindered due to its chemical reactivity and propensity to readily react with moisture. This work aimed at exploring advanced fabrication techniques for LiH such as 1) uniaxial powder pressing methods and 2) laser powder bed fusion (L-PBF) additive manufacturing. Uniaxial powder compaction offers advantageous tailorable mechanical and physical properties via density control, and L-PBF can produce net-shaped complex parts with unique microstructure. Uniaxial pressing proved successful in readily producing LiH with density control.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced Fabrication Techniques of Metal Hydrides for Science and Technology Applications (Full Technical Report)

Lithium Hydride (LiH) atomic properties make it an excellent candidate for thermal energy storage, hydrogen storage, and nuclear reactor technology. High Energy Density (HED) experiments on LiH at the National Ignition Facility (NIF) can also provide critical Equation of State (EOS) and Hugoniot data. Density requirements for LiH vary per application and therefore physical and structural requirements for LiH are non-uniform. Historical production of LiH relies on casting processes that are limited by density and grain-size control, which leads to unfavorable machinable characteristics. LiH manufacturing is further hindered due to its chemical reactivity and propensity to readily react with moisture. This work aimed at exploring advanced fabrication techniques for LiH such as 1) uniaxial powder pressing methods and 2) laser powder bed fusion (L-PBF) additive manufacturing. Uniaxial powder compaction offers advantageous tailorable mechanical and physical properties via density control, and L-PBF can produce net-shaped complex parts with unique microstructure. Uniaxial pressing proved successful in readily producing LiH with density control.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Water Atomized H13 Tool Steel Powders for Binder Jet Additive Manufacturing

ORNL (Contractor) and Ametek, Inc. (Participant) collaborated to determine the feasibility of adopting water atomized H13 tool steel powder for binder jet additive manufacturing (BJAM) for tooling applications. The capability to utilize water atomized powders can substantially reduce powder expenses for BJAM, enabling process competitiveness with casting whilst enabling new applications of high-temperature, net-shaped components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Advanced Anion Exchange Membranes with Tunable Water Transport for PGM-Free AEMFCs

This project advanced the synthesis, characterization, and testing of anion exchange membranes for use in fuel cells. Our goal was to improve the water transport in anion exchange membrane fuel cells to improve their performance and durability. Through the work in this project we: 1) developed new composite anion exchange membranes through polymer synthesis and membrane casting into mechanical supports; 2) optimized electrode architecture and cell conditions to achieve; 3) demonstrated an integrated approach to achieving over 1 W/cm 2 in an operating device. While we did not achieve 1000 hours of continuous operation, we demonstrated multiple runs of more than 300 hours of device performance at steady-state.

08 HYDROGEN↗
DOE OSTI2024

Additive Manufacturing for Large Displacement Unmanned Underwater Vehicles (LDUUVs)

Oak Ridge National Laboratory partnered with Anduril Industries to develop the process for adapting large format additive manufacturing for the production of underwater vehicles. This research started by defining and selecting a polymer for the vehicle panels. Coatings were tested at 9000PSI to ensure proper bonding to the 3D printed panels, then tensile tested to understand the mechanical properties. A vehicle panel fairing set was design optimized for the 3D printing process and then 3D printed. Additional work optimized coatings and tested additional reinforcements methods such as fiber weave and z-casting with fiber rods and resin. Finally, a full vehicle was constructed and successfully tested in open water by Anduril.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid-State Mixed-Potential Electrochemical Sensors for Natural Gas Leak Detection and Quality Control (Final Technical Report)

Mitigation of methane emissions are a critical factor to limiting the impact of the natural gas industry on global climate change. Throughout the period of 2020-2024, the University of New Mexico and its commercialization partner and subcontractor, SensorComm Technologies, Inc. (SCT), have worked together to develop a low-cost Artificial Intelligence (AI)-driven Internet of Things (IoT)-based multi-gas sensor platform for methane emissions detection. In the final year of the project, we extended this work to include hydrogen detection in support of a transition to a hydrogen economy where hydrogen could be transported through existing natural gas infrastructure. Mixed potential electrochemical sensors were first prototyped by ceramic additive manufacturing and then transitioned to conventional ceramic manufacturing tape casting and screen-printing technologies in preparation for mass production. Demonstrated limits of detection of 5 ppm of methane in natural gas and 1 ppm of hydrogen were measured. These limits of detection are among the lowest of solid-state electrochemical sensors that have been reported in the literature or available in the industry. Machine learning algorithms were developed to identify natural gas mixtures with > 98% accuracy level and quantify methane concentrations at 97% accuracy. The presence of hydrogen could also be identified, and its concentration quantified at these accuracy levels. These algorithms were optimized for running on portable computing hardware which enabled > 1 Hz processing rates. A portable packaged IoT system was integrated with the electrochemical sensor in collaboration with SCT. The package consists of readout electronics with < 1 mV resolution, sensor temperature control, and data transmission over cellular wireless and/or Wi-Fi networks. Field testing was performed in two rounds at Colorado State University’s Methane Emissions Technology Evaluation Center (CSU METEC). The first round of testing demonstrated successful measurements of methane from an underground natural gas leak of 20 standard liters per minute (SLPM), which agreed with previously published literature using more sophisticated and expensive analytical equipment. The second round of testing showed that an above ground leak of 2 SLPM of hydrogen could be detected at 32 ft. This project has resulted in six published peer reviewed journal articles, over ten presentations at professional conferences, and one full patent application filed in 2023. Future work on this project includes increased sensitivity, higher production yields, and applications in the hydrogen safety and flare emissions monitoring spaces.

03 NATURAL GAS↗
DOE OSTI2024

Measuring thermal profiles in high explosives using neural networks

We present a new method for calculating the temperature profile of high explosive (HE) material using a Convolutional Neural Network (CNN). To train/test the CNN, we have developed a hybrid experiment/simulation method for collecting acoustic and temperature data. We experimentally heat cylindrical containers of HE material until detonation/deflagration, where we continuously measure the acoustic bursts through the HE using multiple acoustic transducers lined around the exterior container circumference. However, measuring the temperature profile in the HE in an experiment would require inserting a large number of thermal probes, which would disrupt the heating process. Thus, we use two thermal probes, one at the HE center and one at the wall. We then use numerical simulation of the heating process to calculate the temperature distribution and correct the simulated temperatures based on the experimental center and wall temperatures. We calculate temperature errors on the order of 15 °C, which is ~12% of the range of temperatures in the experiment. We also investigate how the algorithm’s accuracy is affected by the number of acoustic receivers used to collect each measurement and the resolution of the temperature prediction. This work provides a means of assessing the safety status of HE material, which cannot be achieved using existing temperature measurement methods. In addition, it has implications for a range of other applications where internal temperature profile measurements would provide critical information. These applications include detecting chemical reactions, observing thermodynamic processes such as combustion, monitoring metal or plastic casting, determining the energy density in thermal storage capsules, and identifying abnormal battery operations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗