SEARCH · Engineering Papers

Results for “beam techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Study program to improve the open-circuit voltage of low resistivity single crystal silicon solar cells

The results of a 14 month program to improve the open circuit voltage of low resistivity silicon solar cells are described. The approach was based on ion implantation in 0.1- to 10.0-ohm-cm float-zone silicon. As a result of the contract effort, open circuit voltages as high as 645 mV (AMO 25 C) were attained by high dose phosphorus implantation followed by furnace annealing and simultaneous SiO2 growth. One key element was to investigate the effects of bandgap narrowing caused by high doping concentrations in the junction layer. Considerable effort was applied to optimization of implant parameters, selection of furnace annealing techniques, and utilization of pulsed electron beam annealing to minimize thermal process-induced defects in the completed solar cells.

Minnucci, J. A.↗

NASA NTRS1979

Characterization of graphite/epoxy laminates for aeroelastic tailoring

A study of interaction between wing bending and twist by graphite/epoxy anisotropic laminates used in aircraft wing skins is presented. The laminates were used as covers for subscale box beams supported as a cantilever and tested in tip shear and tip torque, measuring beam response with a reflected light technique. The results indicated that the in-plane stiffness properties of anisotropic laminates can be predicted if the layer properties of the composite materials are known; thus, the coupled bending/twist response of wing type structures made from these laminates can be determined provided the limits of the laminate linear behavior are not significantly exceeded.

Shyprykevich, P.↗

NASA NTRS1982

A study pertaining to a very low temperature hydrogen maser feasibility

Very low temperature atomic hydrogen masers were developed. The advantages over room temperature hydrogen masers include higher radiated power due to the higher beam intensities possible using low temperature techniques and the much smaller electron spin flip cross section at low temperatures, lower cavity and amplifier noise temperatures, increased stability against mechanical creep at low temperatures, and opportunities to extend H atom collision studies to low temperatures, where quantum effects and details of the interatomic potentials are much more important.

Crampton, S. B.↗

NASA NTRS1982

An EBIC study of dislocation networks in unprocessed and unprocessed web silicon ribbon

Experimental techniques for the preparation of electron beam induced current samples of Web-dentritic silicon are described. Both as grown and processed material were investigated. High density dislocation networks were found close to twin planes in the bulk of the material. The electrical activity of these networks is reduced in processed material.

Fieldler, F. S.↗

NASA NTRS1983

An evaluation of the accuracy of some radar wind profiling techniques

Major advances in Doppler radar measurement in optically clear air have made it feasible to monitor radial velocities in the troposphere and lower stratosphere. For most applications the three dimensional wind vector is monitored rather than the radial velocity. Measurement of the wind vector with a single radar can be made assuming a spatially linear, time invariant wind field. The components and derivatives of the wind are estimated by the parameters of a linear regression of the radial velocities on functions of their spatial locations. The accuracy of the wind measurement thus depends on the locations of the radial velocities. The suitability is evaluated of some of the common retrieval techniques for simultaneous measurement of both the vertical and horizontal wind components. The techniques considered for study are fixed beam, azimuthal scanning (VAD) and elevation scanning (VED).

Koscielny, A. J.↗

NASA NTRS1988

Study of optical output couplers for submillimeter wavelength backward-wave oscillators (BWO's)

The machining of slow wave structures for high frequency backward-wave oscillators (BWO) is extremely difficult beyond 1 THz. Recently a microfabrication technique using photolithography and ion-beam assisted etching has been used to construct a prototype BWO operating at 200 to 265 GHz. The output coupler for such tubes remains a problem. Waveguides do not exist or are very lossy at the frequencies of interest (300 to 2000 GHz). This paper discusses several scaled experiments of optical output couplers for submillimeter BWOs. Various designs of planar antennas (Vivaldi horns) and lens-feed systems (Hyperhemispherical lens) were constructed and tested between 20 and 100 GHz using a spectrum analyzer. The lens system was also tested at 337 GHz using a CO2 pumped FIR laser.

Cook, Jerry D.↗

NASA NTRS1987

An optical processor for object recognition and tracking

The design and development of a miniaturized optical processor that performs real time image correlation are described. The optical correlator utilizes the Vander Lugt matched spatial filter technique. The correlation output, a focused beam of light, is imaged onto a CMOS photodetector array. In addition to performing target recognition, the device also tracks the target. The hardware, composed of optical and electro-optical components, occupies only 590 cu cm of volume. A complete correlator system would also include an input imaging lens. This optical processing system is compact, rugged, requires only 3.5 watts of operating power, and weighs less than 3 kg. It represents a major achievement in miniaturizing optical processors. When considered as a special-purpose processing unit, it is an attractive alternative to conventional digital image recognition processing. It is conceivable that the combined technology of both optical and ditital processing could result in a very advanced robot vision system.

Sloan, J.↗

NASA NTRS1989

A novel array antenna for MSAT applications

The issue of reducing the cost of phased array vehicle antennas through the use of a lens feeding arrangement instead of phase shifters at each element is addressed. In particular, the economic viability of a mobile satellite system (MSAT) is largely dependent on the efficient use of the allocated scarce spectrum and orbit as well as the satellite power. the type of vehicle antenna used will play a critical role in achieving this efficiency. A standard design approach for an electronically steered array uses phase shifters at each element to provide beam steering. A method for reducing the required number of phase shifters by using an R-KR lens feed network is outlined. The authors briefly discuss the phase shifter approach to beam steering, examine various lens feed techniques, and describe the R-KR lens approach. The lens feed network architecture is examined, a computer model for simulation of the array is presented, and the results of analysis of a suggested design for the MSAT application are given. In addition, satellite acquisition and tracking considerations are investigated.

Bodnar, Donald G.↗

NASA NTRS1991

Characterization of devices, circuits, and high-temperature superconductor transmission lines by electro-optic testing

The development of a capability for testing transmission lines, devices, and circuits using the optically-based technique of electro-optics sampling was the goal of this project. Electro-optic network analysis of a high-speed device was demonstrated. The project involved research on all of the facets necessary in order to realize this result, including the discovery of the optimum electronic pulse source, development of an adequate test fixture, improvement of the electro-optic probe tip, and identification of a device which responded at high frequency but did not oscillate in the test fixture. In addition, during the process of investigating patterned high-critical-temperature superconductors, several non-contacting techniques for the determination of the transport properties of high T(sub c) films were developed and implemented. These are a transient, optical pump-probe, time-resolved reflectivity experiment, an impulsive-stimulated Raman scattering experiment, and a terahertz-beam coherent-spectroscopy experiment. The latter technique has enabled us to measure both the complex refractive index of an MgO substrate used for high-T(sub c) films and the complex conductivity of a YBa2Cu3O(7-x) sample. This information was acquired across an extremely wide frequency range: from the microwave to the submillimeter-wave regime. The experiments on the YBCO were conducted without patterning of, or contact to, the thin film. Thus, the need for the more difficult transmission-line experiments was eliminated. Progress in all of these areas was made and is documented in a number of papers. These papers may be found in the section listing the abstracts of the publications that were issued during the course of the research.

Whitaker, John F.↗

NASA NTRS1991

Dynamic analysis of truss-beam system

A simple truss-beam method for determining the dynamic characteristics of the space structures intended to perform various tasks in orbit is presented. Algorithms are provided to determine the flexibility matrix of the truss beam for use in the equation of motion. The natural frequencies obtained through this method are compared with those obtained through the finite element method. An experimental procedure for verifying the theoretical results is described. It is concluded that the truss-beam method is a simple analysis technique that yields reasonably accurate results with a minimum of computational effort, especially for the critical lower bending modes of flexible structures. The method takes less computer time than more conventional methods and can be programed in both BASIC and FORTRAN for use in micro- and mainframe computers.

Abu-Saba, Elias G.↗

NASA NTRS1991

Mineralogy and matrix composition of CR chondrites Renazzo and EET 87770, and ungrouped chondrites Essebi and MAC 87300

The fine-grained mineralogy of the matrix of two CR chondrites, Renazzo and EET 87770, and the ungrouped (but possible related) Essebi and MAC 87300 chondrites was characterized using standard microprobe (focussed beam) and transmission electron microscopy (TEM) techniques (using ultramicrotomed sections). These results are compared to previously obtained results for 31 other carbonaceous chondrites.

Zolensky, Michael E.↗

NASA NTRS1990

Future developments in aeronautical satellite communications

Very shortly aeronautical satellite communications will be introduced on a world wide basis. By the end of the year, voice communications (both to the cabin and cockpit) and packet data communications will be available to both airlines and executive aircraft. During the decade following the introduction of the system, there will be many enhancements and developments which will increase the range of applications, expand the potential number of users, and reduce costs. A number of ways in which the system is expected to evolve over this period are presented. Among the issues which are covered are the impact of spot beam satellites, spectrum and power conservation techniques, and the expanding range of user services.

Wood, Peter↗

NASA NTRS1992

Continuation of tailored composite structures of ordered staple thermoplastic material

The search for the cost effective composite structure has motivated the investigation of several approaches to develop composite structure from innovative material forms. Among the promising approaches is the conversion of a planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. A framework was established which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. Predictions for the effective viscosities of a hyper-anisotropic medium consisting of collimated, discontinuous fibers suspended in viscous matrix were extended to capture the characteristics of typical polymers including non-Newtonian behavior and temperature dependence. In addition, the influence of fiber misorientation was also modeled by compliance averaging to determine ensemble properties for a given orientation distribution. A design tool is presented for predicting the effect of material heterogeneity on the performance of curved composite beams such as those used in aircraft fuselage structures. Material heterogeneity can be induced during manufacturing processes such as sheet forming and stretch forming of thermoplastic composites. This heterogeneity can be introduced in the form of fiber realignment and spreading during the manufacturing process causing radial and tangential gradients in material properties. Two analysis procedures are used to solve the beam problems. The first method uses separate two-dimensional elasticity solutions for the stresses in the flange and web sections of the beam. The separate solutions are coupled by requiring that forces and displacements match section boundaries. The second method uses an approximate Rayleigh-Ritz technique to find the solutions for more complex beams. Analyses are performed for curved beams of various cross-sections loaded in pure bending and with a uniform distributed load. Preliminary results show that the geometry of the beam dictates the effect of heterogeneity on performance. The role of heterogeneity is larger in beams with a small average radius-to-depth ration, R/t, where R is the average radius of the beam and t is the difference between the inside and outside radii. Results of the anlysis are in the form of stresses and displacements and are compared to both mechanics of materials and numerical solutions obtained using finite element analysis.

Santare, Michael H.↗

NASA NTRS1990

Time dependency of temperature of a laser-irradiated infrared target pixel as a low-pass filter

The thermal response of a surface layer of a pixel on an infrared target simulator is discussed. This pixel is maintained at a constant temperature by a rapidly scanning laser beam. An analytical model has been developed to describe the exact temperature dependence of a pixel as a function of time for different pixel refresh rates. The top layer of the pixel surface that generates the gray-body radiation shows the temperature dependence on time that is characteristic of a low-pass filter. The experimental results agree with the analytical predictions. The application of a pulsed laser beam to a noncontact, nondestructive diagnostic technique of surface characterization for the presence of microdefects is discussed.

Scholl, Marija S.↗

NASA NTRS1992

Laser-based strain measurements for high temperature applications

The Instrumentation and Control Technology Division at NASA Lewis Research Center has developed a high performance optical strain measurement system for high temperature applications using wires and fibers. The system is based on Yamaguchi's two-beam speckle-shift strain measurement technique. The system automatically calculates surface strains at a rate of 5 Hz using a digital signal processor in a high speed micro-computer. The system is fully automated, and can be operated remotely. This report describes the speckle-shift technique and the latest NASA system design. It also shows low temperature strain test results obtained from small diameter tungsten, silicon carbide, and sapphire specimens. These specimens are of interest due to their roles in composite materials research at NASA Lewis.

Lant, Christian T.↗

NASA NTRS1996

The Implications of ACTS Technology on the Requirements of Rain Attenuation Modeling for Communication System Specification and Analysis at 30/20 GHz and Beyond

The advent of the use of the Ka-Band for space communications, coupled with the introduction of digital modulation techniques as well as multiple-beam methodology for satellites, has deemed it necessary to reassess the plethora of rain attenuation prediction models in use. The Advanced Communication Technology Satellite (ACTS) Project, undertaken by the National Aeronautics and Space Administration in 1983, offered such challenges to rain attenuation prediction modeling. Up to 1983, no such single modeling formalism existed that could fill such requirements. Not even the work done by the NASA Propagation Experimenters (NAPEX) Group had envisioned such requirements, so no dynamic Ka-Band data existed from which one could draw conclusions. In this paper, the basic rudiments of what has become to be known as the 'ACTS Rain Attenuation Prediction Model' will be presented. The concept of rain fade mitigation control availability will be introduced. A new evaluation is then presented for the performance of satellite communication systems, in particular, those to be operating within the Ka-Band and above, that will necessarily employ some type of dynamic rain fade mitigation procedure.

Manning, Robert M.↗

NASA NTRS2008

Grazing-Incidence Neutron Optics based on Wolter Geometries

The feasibility of grazing-incidence neutron imaging optics based on the Wolter geometries have been successfully demonstrated. Biological microscopy, neutron radiography, medical imaging, neutron crystallography and boron neutron capture therapy would benefit from high resolution focusing neutron optics. Two bounce optics can also be used to focus neutrons in SANS experiments. Here, the use of the optics would result in lower values of obtainable scattering angles. The high efficiency of the optics permits a decrease in the minimum scattering vector without lowering the neutron intensity on sample. In this application, a significant advantage of the reflective optics over refractive optics is that the focus is independent of wavelength, so that the technique can be applied to polychromatic beams at pulsed neutron sources.

Gubarev, M. V.↗

NASA NTRS2008

A Resonant Damping Study Using Piezoelectric Materials

Excessive vibration of turbomachinery blades causes high cycle fatigue (HCF) problems requiring damping treatments to mitigate vibration levels. Based on the technical challenges and requirements learned from previous turbomachinery blade research, a feasibility study of resonant damping control using shunted piezoelectric patches with passive and active control techniques has been conducted on cantilever beam specimens. Test results for the passive damping circuit show that the optimum resistive shunt circuit reduces the third bending resonant vibration by almost 50%, and the optimum inductive circuit reduces the vibration by 90%. In a separate test, active control reduced vibration by approximately 98%.

Min, J. B.↗