Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Experimental heating distributions for biconics at incidence in Mach 10 air and comparison to prediction

Heating distributions were measured on a 1.9 percent scale model of a generic, aeroassisted vehicle proposed for missions to a number of planets and also a candidate as a moderate L/D earth orbital transfer vehicle. This vehicle is a spherically blunted, 13 deg/7 deg biconic with the fore-cone bent upward 7 deg to provide self-trim capability; also tested was a straight biconic with the same noise radius and half angles. These measurements were made in the Langley 31-Inch Mach 10 Tunnel at values of the free-stream Reynolds number, based on model length, equal to 0.2 and 0.9 million. The angle of attack, referenced to the aft cone, was varied from 0 to 20 deg. Heating distributions predicted with a parabolized Navier Stokes (PNS) code are compared to measurement over the present range of Reynolds number and angle of attack. Windward heating was predicted to within 10 percent by the PNS code. Leeward heating distributions were predicted qualitatively for both values of Reynolds number, but quantitative agreement was poorer than on the windward side.

Miller, C. G.↗
NASA NTRS1985

Sidewall boundary-layer effects in two-dimensional airfoil testing

Theoretical studies required to evaluate and validate the streamlined wall test section of the 0.3 m transonic Cryogenic Tunnel were initiated. The various aspects that are being considered presently are deviations of the real wall shape from the true streamline shape, wall adjustment strategy, and the influence of the sidewall boundary layers. Since the top and bottom walls are supported at a finite number of jack points, the true wall shape will be different from the ideal streamline shape. This is determined by calculating the structural shape for cases for which the exact streamline shape can be calculated. For the structural shape calculations, the MSCNASTRAN code is being used. To start with, comparisons are made using simple singularities for model representation and also for a flat plate at angle of attack.

Murthy, A. V.↗
NASA NTRS1988

Research investigation of helicopter main rotor/tail rotor interaction noise

Acoustic measurements were obtained in a Langley 14 x 22 foot Subsonic Wind Tunnel to study the aeroacoustic interaction of 1/5th scale main rotor, tail rotor, and fuselage models. An extensive aeroacoustic data base was acquired for main rotor, tail rotor, fuselage aerodynamic interaction for moderate forward speed flight conditions. The details of the rotor models, experimental design and procedure, aerodynamic and acoustic data acquisition and reduction are presented. The model was initially operated in trim for selected fuselage angle of attack, main rotor tip-path-plane angle, and main rotor thrust combinations. The effects of repositioning the tail rotor in the main rotor wake and the corresponding tail rotor countertorque requirements were determined. Each rotor was subsequently tested in isolation at the thrust and angle of attack combinations for trim. The acoustic data indicated that the noise was primarily dominated by the main rotor, especially for moderate speed main rotor blade-vortex interaction conditions. The tail rotor noise increased when the main rotor was removed indicating that tail rotor inflow was improved with the main rotor present.

Fitzgerald, J.↗
NASA NTRS1989

Updated users' guide for TAWFIVE with multigrid

A program for the Transonic Analysis of a Wing and Fuselage with Interacted Viscous Effects (TAWFIVE) was improved by the incorporation of multigrid and a method to specify lift coefficient rather than angle-of-attack. A finite volume full potential multigrid method is used to model the outer inviscid flow field. First order viscous effects are modeled by a 3-D integral boundary layer method. Both turbulent and laminar boundary layers are treated. Wake thickness effects are modeled using a 2-D strip method. A brief discussion of the engineering aspects of the program is given. The input, output, and use of the program are covered in detail. Sample results are given showing the effects of boundary layer corrections and the capability of the lift specification method.

Melson, N. Duane↗
NASA NTRS1989

Nonlinear control of a supermaneuverable aircraft

This paper describes a technique which may be used to design the flight control system for a highly maneuverable aircraft. The control system was provided to stabilize the dynamics of the aircraft model and allow it to fly simulated, poststall 'supermaneuvers'. Although the aircraft dynamics are highly nonlinear under these conditions, the gain-scheduled, flight control system was designed using basically linear techniques. A manuever generator was implemented to pilot the mathematical model through prescribed optimal trajectories. The control system design performed well while executing maneuvers involving small angular rates where the governing dynamics could be considered linear. However, the performance deteriorated once the model was subjected to high angular rates at high angle of attack.

Snell, S. Antony↗
NASA NTRS1952

A Low-speed Investigation of an Annular Transonic Air Inlet

Low-speed wind-tunnel tests were conducted as preliminary steps in the study of fuselage-air-inlet arrangements believed suitable for use at transonic speeds. The forward part of the model consisted of an NACA 1-85-050 cowling located at the base of the long protruding fuselage nose designed to maintain substream surface velocities everywhere ahead of the entrance and thereby to avoid or minimize adverse boundary-layer-shock interaction effects up to low supersonic speeds. Pressure-recovery and surface-pressure measurements are presented for the model with three fuselage nose shapes for ranges of angle of attack and inlet-velocity ratio useful for high-speed flight

AIR INLETS, SCOOPS↗
NASA NTRS2011

Modeling Humans as Reinforcement Learners: How to Predict Human Behavior in Multi-Stage Games

This paper introduces a novel framework for modeling interacting humans in a multi-stage game environment by combining concepts from game theory and reinforcement learning. The proposed model has the following desirable characteristics: (1) Bounded rational players, (2) strategic (i.e., players account for one anothers reward functions), and (3) is computationally feasible even on moderately large real-world systems. To do this we extend level-K reasoning to policy space to, for the first time, be able to handle multiple time steps. This allows us to decompose the problem into a series of smaller ones where we can apply standard reinforcement learning algorithms. We investigate these ideas in a cyber-battle scenario over a smart power grid and discuss the relationship between the behavior predicted by our model and what one might expect of real human defenders and attackers.

Lee, Ritchie↗
NASA NTRS1991

Nonlinear time-series-based adaptive control applications

A control design methodology based on a nonlinear time-series reference model is presented. It is indicated by highly nonlinear simulations that such designs successfully stabilize troublesome aircraft maneuvers undergoing large changes in angle of attack as well as large electric power transients due to line faults. In both applications, the nonlinear controller was significantly better than the corresponding linear adaptive controller. For the electric power network, a flexible AC transmission system with series capacitor power feedback control is studied. A bilinear autoregressive moving average reference model is identified from system data, and the feedback control is manipulated according to a desired reference state. The control is optimized according to a predictive one-step quadratic performance index. A similar algorithm is derived for control of rapid changes in aircraft angle of attack over a normally unstable flight regime. In the latter case, however, a generalization of a bilinear time-series model reference includes quadratic and cubic terms in angle of attack.

Mohler, R. R.↗
NASA NTRS2022

Supporting Hazard Analysis for Wildfire Response Using fmdtools and MIKA

The System Wide Safety (SWS) Safety Demonstrator (SD) Series drives development of an increasingly capable In-Time Aviation Safety Management System (IASMS) focusing on humanitarian applications, starting with wildfire response (SD-1). The goals of this report are to (1) provide an early hazard analysis and mitigation evaluation of wildfire response to support these efforts and (2) provide a demonstration of capabilities of the Fault Model Design Tools (fmdtools) and Manager for Intelligent Knowledge Access (MIKA) tools. fmdtools provides a modeling, simulation, and resiliency analysis framework in which a wildfire response model, the System Modeling and Analysis of Resiliency in Scalable Traffic Management for Emergency Response Operations (SMARt-STEReO), is built. MIKA is an intelligent knowledge manager with several capabilities, including assisting in hazard analysis by extracting and analyzing hazards from historical incident reports. The following topics are covered in the report: Understanding Wildfire Hazard Dynamics. We provide a description and simulated examples of how hazards occur in the SMARt-STEReO model of wildfire response and their effect on its outcome. This provides a common mental model and focuses the analysis presented in the remainder of the report. Wildfire Hazard Identification. MIKA identifies wildfire hazards from three relevant datasets: the ICS-209-PLUS, SAFECOM, and SAFENET. Hazards are manually organized into a taxonomy and MIKA analyzes each hazard’s effects, likelihood, severity, and risk. Evaluating Mitigation Strategies. The SMARt-STEReO wildfire response model built in fmdtools evaluates a subset of identified hazards. Specifically, we simulate the effect of communications faults and equipment faults on operator safety, the effect of changing winds and flammability, and a scenario with multiple ignition points and heavy smoke. Tool Limitations and Usage Considerations. We provide a discussion of appropriate tool use cases as well as limitations and considerations for usage. The tool findings are used to synthesize recommendations for wildfire response operations, which can be captured as part of an IASMS. Key recommendations are as follows: Hazards are identified from a broad spectrum of sources including aircraft subsystems, operational sources, and ground crew operations. Highest risk operational environment hazards identified are Evacuations. The highest risk manned aerial operations hazard categorized is Jumper Operations Mishap. Ground crew hazards that are highest risk are Burns, Cargo Operations Overhead, Dehydration, Entrapment, Falling Objects, Heart Attacks, Heat Exhaustion, Inadequate Training or Certification, Vehicle Breakdown, and Vehicle Collision. Modelled containment failures arise from a mismatch between the difficulty of the firefighting scenario and the capacity (e.g., speed, effectiveness, awareness) of the response. In firefighting scenarios where containment is possible (e.g., because the fire does not spread too quickly), these mismatches can occur because of a change in environmental conditions (e.g., wind, flammability, etc) or because of planning, equipment, or communications faults. Improvements to communications increase the capacity of the firefighting response by reducing the time needed to respond to the fire. While surveillance does not increase this capacity by itself, it increases operator safety by increasing state awareness, enabling firefighters to evade approaching fires. Increasing both has a synergistic effect. In general, these performance and resilience increases generalize over fault scenarios as well as unforeseen changes to circumstances (i.e., wind, aridity, etc.). However, these improvements need to be designed so as not to make the system prone to persistent large-scale communications outages, which can reduce performance.

Hazard analysis↗
NASA NTRS1975

Calculation of three-dimensional compressible laminar and turbulent boundary layers. An implicit finite-difference procedure for solving the three-dimensional compressible laminar, transitional, and turbulent boundary-layer equations

An implicit finite-difference procedure is presented for solving the compressible three-dimensional boundary-layer equations. The method is second-order accurate, unconditionally stable (conditional stability for reverse cross flow), and efficient from the viewpoint of computer storage and processing time. The Reynolds stress terms are modeled by (1) a single-layer mixing length model and (2) a two-layer eddy viscosity model. These models, although simple in concept, accurately predicted the equilibrium turbulent flow for the conditions considered. Numerical results are compared with experimental wall and profile data for a cone at an angle of attack larger than the cone semiapex angle. These comparisons clearly indicate that the numerical procedure and turbulence models accurately predict the experimental data with as few as 21 nodal points in the plane normal to the wall boundary.

Harris, J. E.↗
NASA NTRS2004

Experimental Aerothermodynamics In Support Of The Columbia Accident Investigation

The technical foundation for the most probable damage scenario reported in the Columbia Accident Investigation Board's final report was largely derived from synergistic aerodynamic/aerothermodynamic wind tunnel measurements and inviscid predictions made at NASA Langley Research Center and later corroborated with engineering analysis, high fidelity numerical viscous simulations, and foam impact testing near the close of the investigation. This report provides an overview of the hypersonic aerothermodynamic wind tunnel program conducted at NASA Langley and illustrates how the ground-based heating measurements provided early insight that guided the direction and utilization of agency resources in support of the investigation. Global surface heat transfer mappings, surface streamline patterns, and shock shapes were measured on 0.0075 scale models of the Orbiter configuration with and without postulated damage to the thermal protection system. Test parametrics include angle of attack from 38 to 42 degs, sideslip angles of 38 to 42 degs, sideslip angles of plus or minus 1 deg, Reynolds numbers based upon model length from 0.05 x 10(exp 6) to 6.5 x 10(exp 6), and normal shock density ratios of 5 (Mach 6 Air) and 12 (Mach 6 CF4). The primary objective of the testing was to provide surface heating characteristics on scaled Orbiter models with outer mold line perturbations to simulate various forms of localized surface damage to the thermal protection system. Initial experimental testing conducted within two weeks of the accident simulated a broad spectrum of thermal protection system damage to the Orbiter windward surface and was used to refute several hypothesized forms of thermal protection system damage, which included gouges in the windward thermal protection system tiles, breaches through the wing new the main landing gear door, and protuberances along the wing leading edge that produced asymmetric boundary layer transition. As the forensic phase of the investigation developed and the condition of recovered debris was examined, increasing emphasis was placed on identifying wing leading edge damage (partially and fully missing reinforced carbon-carbon panels, and eventually holes in the wing leading edge with venting to the wing upper surface) that produced off-nominal heating trends consistent with extracted Orbiter flight recorder temperature data.

Horvath, Thomas J.↗
NASA NTRS2005

An Investigation of the Impact of Aerodynamic Model Fidelity on Close-In Combat Effectiveness Prediction in Piloted Simulation

Several aircraft airframe modeling approaches are currently being used in the DoD community for acquisition, threat evaluation, training, and other purposes. To date there has been no clear empirical study of the impact of airframe simulation fidelity on piloted real-time aircraft simulation study results, or when use of a particular level of fidelity is indicated. This paper documents a series of piloted simulation studies using three different levels of airframe model fidelity. This study was conducted using the NASA Langley Differential Maneuvering Simulator. Evaluations were conducted with three pilots for scenarios requiring extensive maneuvering of the airplanes during air combat. In many cases, a low-fidelity modified point-mass model may be sufficient to evaluate the combat effectiveness of the aircraft. However, in cases where high angle-of-attack flying qualities and aerodynamic performance are a factor or when precision tracking ability of the aircraft must be represented, use of high-fidelity models is indicated.

Persing, T. Ray↗
NASA NTRS1981

Decision Aids for Airborne Intercept Operations in Advanced Aircrafts

A tactical decision aid (TDA) for the F-14 aircrew, i.e., the naval flight officer and pilot, in conducting a multitarget attack during the performance of a Combat Air Patrol (CAP) role is presented. The TDA employs hierarchical multiattribute utility models for characterizing mission objectives in operationally measurable terms, rule based AI-models for tactical posture selection, and fast time simulation for maneuver consequence prediction. The TDA makes aspect maneuver recommendations, selects and displays the optimum mission posture, evaluates attackable and potentially attackable subsets, and recommends the 'best' attackable subset along with the required course perturbation.

Madni, A.↗
NASA NTRS1993

3-D viscous flow CFD analysis of the propeller effect on an advanced ducted propeller subsonic inlet

The time-marching Navier-Stokes code PARC3D was used to study the 3D viscous flow associated with an advanced ducted propeller subsonic inlet at take-off operating conditions. At a free stream Mach number of 0.2, experimental data for the inlet-with-propeller test model indicated that the airflow was attached on the cowl windward lip at an angle of attack of 25 deg became unstable at 29 deg, and separated at 30 deg. An experimental study with a similar inlet and without propeller (through-flow) indicated that flow separation occurred at an angle of attack a few degrees below the value observed when the inlet was tested with the propeller, indicating the propeller's favorable effect on inlet performance. In the present numerical study, flow blockage analogous to the propeller was modeled via a PARC3D computational boundary condition (BC), the 'screen BC', based on 1-1/2 dimension actuator disk theory. The application of the screen BC in this numerical study provided results similar to those of past experimental efforts in which either the blockage device or the propeller was used.

Iek, Chanthy↗
NASA NTRS1957

Interference Effects of Fuselage-Stored Missiles on Inlet Duct Model of an Interceptor-Type Aircraft at Mach Numbers 1.5 to 1.9

The effect of missile armament on the performance of an interceptor-type aircraft model has been determined at Mach numbers 1.5, 1.7, and 1.9 and at angles of attack to 19 deg. With this configuration missiles were carried in a bay located on the bottom of the aircraft fuselage and mounted to a rotatable missile door. Rotation of the door then brought the missiles into the external or firing position. The aircraft model was characterized by triangular-shaped normal-shock inlets located at the wing roots. Relatively short and curved subsonic diffusers fed simulated twin side-by-side turbojet engines. Inasmuch as the missile bay extended considerably ahead of the inlet station, rotation of the missile door created considerable disturbance of the flow entering the inlets. In comparison with the internal missile arrangement, the external missile configurations increased the model lift, drag, and pitching moment. While the diffuser-exit flow distortion and static-pressure fluctuations were not greatly affected, diffuser total-pressure recovery was reduced as much as 0.058 at Mach number 1.9 for one missile configuration. The most detrimental effect of missile-door rotation occurred at the transient door positions, or with the door halfwzy between the missiles-in and -out conditions. At this door position the flow into the inlets was highly asymmetrical. Although the performance of both left and right ducts was generally reduced, the inlet duct on the cavity side of the missile door was most severely penalized, becoming unstable recovery losses and increases in flow distortion. The installation of fuselage fences along the missile bay was only partially effective in reducing these losses.

Piercy, T. G.↗
NASA NTRSDate not supplied

A Wall-Modeled LES Perspective for the High Lift Common Research Model Using LAVA

A new immersed boundary Wall-Modelled Large Eddy Simulation (WMLES) formulation is developed to study high-lift aerodynamics on the NASA High-Lift Common Research Model (HL-CRM). A sequence of Cartesian Octree grids with sizes ranging from 100 Million through 2.02 Billion grid points is utilized to systematically assess grid-sensitivity and convergence for the in-tunnel (QinetiQ) configuration of the model, and remarkable agreement between the immersed boundary and the curvilinear body-aligned WMLES formulations is reported on grids with comparable resolutions. In the free-air configuration of the model, consistent predictions between the Curvilinear Overset and the Cartesian Octree formulations are reported for angles of attack up to C(L,max) at a=19.57. However, some differences in the onset of stall are seen between the two methods for a>20°: while the curvilinear WMLES experiences wing-root separation with increasing angle of attack (Topology A), the Cartesian Octree formulation shows a different flow topology characterized by boundary layer weakness on the main element, emanating from the pylon-wing attachment (Topology B). In order to obtain further insight into the two-distinct topologies, carefully designed numerical experiments to isolate effects of the model standoff and the tunnel wall-boundary layers are conducted using the immersed boundary WMLES formulation. The increased incidence angle-of-attack on the inboard portion of the wing due to the standoff is shown to be sufficient for triggering a switch from Topology B to Topology A in Cartesian WMLES. The role of the floor boundary layer is further examined in detail by identification of additional corner-flow vorticity generated by the viscous juncture flow interactions between the floor boundary layer and the standoff leading to formation of a strong coherent and persistent vortex on the belly-side of the fuselage. The intensity of this vortex is shown to increase with the thickness of the floor boundary layer. A further increase in the incidence angle of attack near the leading-edge strake caused by the presence of this belly-side vortex is quantified for two-distinct floor boundary layers. Both of the floor boundary layers considered result in the onset of large scale wing-root separation at a=21.47in non-confined (free-air) configurations.

TTT↗
NASA NTRS1981

The unsteady suction analogy and applications

A method of the unsteady suction analogy is developed using the unsteady quasi-vortex-lattice method which accurately predicts unsteady leading-edge and side-edge suction forces, and applies to any reduced frequencies. The importance of vortex lag is demonstrated, and damping derivatives, including roll and pitch damping derivatives with reduced frequencies and angles of attack are accurately predicted. Agreement of predicted pitch stiffness derivatives, however, is found to depend on the Reynolds number, possible aeroelastic effect, and the degree of edge-separated vortex flow on the model. Applications to the prediction of longitudinal dynamic stability derivatives for slender wings at high angles of attack are also presented.

Lan, C. E.↗