Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “active layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Solid-State Sintering of Core-Shell Ceramic Powders Fabricated by Particle Atomic Layer Deposition

The properties of technical ceramics are highly dependent on their microstructure, which evolves during sintering. Sintering is the process by which ceramic parts are subjected to high temperatures to activate chemical diffusion and the consumption of porosity. During the initial stage of sintering, interparticle necks between neighboring particles form and subsequently increase in size, consuming porosity as the particle centers move closer together. To experimentally determine how this process depends on particle surface composition, particle atomic layer deposition (ALD) was used to deposit a thin film of amorphous aluminum oxide (Al2O3) onto yttria-stabilized tetragonal zirconia (3YSZ) particles, producing core-shell structured powders. The uniformity of the Al2O3 film was confirmed with transmission electron microscopy and energy dispersive spectroscopy. Scanning electron microscopy was used to observe microstructural evolution during sintering, and the dihedral angles of Al2O3 and 3YSZ grains were measured to determine the ratio of interfacial energies between the 3YSZ|3YSZ, 3YSZ|Al2O3, and Al2O3|Al2O3 interfaces. Analysis of the densification kinetics revealed that the initial stage of densification is dependent on the material at the surface of the particles (ie, the Al2O3 film) and is controlled by the diffusion of Al3+ cations through Al2O3. Once the Al2O3 film has coalesced, the sintering behavior is controlled by the densification of the core material (3YSZ). Thus, core-shell powders fabricated by particle ALD sinter by a two-step process where the kinetics are dependent on the material present at interparticle contacts.

alumina↗
DOE OSTI2026

Designing the Platinum Catalyst Layer for Improved Performance and Durability in Anion Exchange Membrane Water Electrolysis

To lower the cost of hydrogen produced by anion exchange membrane water electrolysis (AEMWE), it is critical to reduce the use of platinum group metal (PGM) catalysts within the device. While iridium has been successfully replaced with PGM-free catalysts at the anode, platinum-based (Pt) cathode catalysts are still required to meet the activity and durability targets. This study investigates the impact of commercial Pt/C catalyst loading, ionomer type and content, and electrode fabrication method on the cathode catalyst layer properties and AEMWE performance with the aim of determining the feasibility of reduced Pt loadings. While increased Pt loading is found to improve beginning-of-life performance, the effects are minimal above 0.6 mg/cm 2 . Ink characterization shows that ionomer type and content affect the ink stability, particle size, and percent of unbound ionomer, which further impact the homogeneity of the sprayed catalyst layers. The 5% PiperION cathode exhibited the highest performance, which may be attributed to a balance between the small particle size and the low proportion of unbound ionomer, minimizing kinetic and transport losses. Theoretical calculations show that the ionomers interact differently with the Pt surface, causing different surface charges and water adsorption strength and activating different mechanisms for hydrogen evolution. Pt-PiperION lowered the enthalpy of water-splitting by 0.1 eV compared to Pt alone and allowed for equal site access between adsorbed H* and OH* (both adsorbed at circa −2.2 eV). Although catalyst-coated membrane (CCM) fabrication techniques are desirable for scale-up, no performance enhancement is observed compared with the catalyst-coated substrate approach. Durability, as measured by degradation rates, Pt loss, and catalyst layer restructuring, was found to improve with increased Pt loadings, higher ionomer content, and CCM architectures. These findings provide important insight into the significant role of the cathode in AEMWE and strategies for maintaining the performance with low Pt loading or PGM-free catalysts.

08 HYDROGEN↗
DOE OSTI2022

A Study of How LaFeO 3 and CaTiO 3 Supports Affect the Oxidation, Hydrogenation, and Methane Steam Reforming Activity of Pt and Ni Catalysts

The structure and catalytic properties of Pt and Ni supported on thin films of LaFeO 3 and CaTiO 3 , prepared by Atomic Layer Deposition (ALD), were investigated. X-Ray diffraction (XRD) and scanning transmission electron microscopy (STEM) show that reduction at 1073 K causes Pt-Fe intermetallic compound formation for Pt/LaFeO 3 . For Pt/CaTiO 3 , 1073-K reduction induces local decomposition of the CaTiO 3 with migration of Ti to the Pt. Reduced Pt/LaFeO 3 and Pt/CaTiO 3 exhibited CO-oxidation activity similar to that for Pt supported on MgAl 2 O 4 but were much less active for propane oxidation and hydrogenation of 1-hexene and toluene. In contrast, Ni/CaTiO 3 behaved similarly to a conventional supported Ni catalyst for the methane-steam-reforming (MSR) and 1-hexene hydrogenation. There was also no evidence for local decomposition of the perovskite in the vicinity of the Ni particles. Furthermore, the results obtained in this study demonstrate that metal-perovskite interactions that affect reactivity are specific to each component.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Localized Hydrophobicity in Aqueous Zinc Electrolytes Improves Zinc Metal Reversibility

The rechargeability of aqueous zinc metal batteries is plagued by parasitic reactions of the zinc metal anode and detrimental morphologies such as dendritic or dead zinc. To improve the zinc metal reversibility, hereby we report a new solution structure of aqueous electrolyte with hydroxyl-ions scavengers and hydrophobicity localized in solvent clusters. In this work we show that although hydrophobicity sounds counterintuitive for an aqueous system, hydrophilic pockets may be encapsulated inside a hydrophobic outer layer and a hydrophobic anode-electrolyte interface can be generated through the addition of a cation-philic, strongly anion-phobic, and OH - -reactive diluent. The localized hydrophobicity enables less active water and less absorbed water on the Zn anode surface, which suppresses the parasitic water reductions; while the hydroxyl-ion-scavenging functionality further minimizes undesired passivation layer formation, thus leading to superior reversibility (an average Zn plating/stripping efficiency of 99.72% for 1000 cycles) and lifetime (80.6% capacity retention after 5000 cycles) of zinc batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

First-Principles Characterization of Surface Phonons of Halide Perovskite CsPbI 3 and Their Role in Stabilization

The stability of halide perovskites has been a long-standing issue for their real-world application. Approaches to improve stability include nanostructuring, dimensionality reduction, and strain engineering, where surfaces play an important role in the formation of a stable structure. To understand the mechanism we compute the lattice dynamics of the surface of CsPbI 3 using density functional theory. We demonstrate, for the first time, that CsPbI 3 crystals exhibit surface phonons that are localized on the outermost layers of the slabs, and we perform a complete symmetry characterization including an identification of the Raman/IR active modes. These surface phonons are present in the optically active cubic phase but are absent in the optically inactive "yellow" phase. Furthermore, we show that the surface suppresses bulk instabilities by hardening soft modes of the bulk cubic phase, resulting in phase stabilization and quenching of dynamical disorder. Finally, this study is fundamental for understanding the structural behavior of halide perovskite materials with high surface area-to-volume ratios, and for guiding stabilization strategies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Fourier Neural Networks as Function Approximators and Differential Equation Solvers

We present a Fourier neural network (FNN) that can be mapped directly to the Fourier decomposition. The choice of activation and loss function yields results that replicate a Fourier series expansion closely while preserving a straightforward architecture with a single hidden layer. The simplicity of this network architecture facilitates the integration with any other higher-complexity networks, at a data pre- or postprocessing stage. We validate this FNN on naturally periodic smooth functions and on piecewise continuous periodic functions. We showcase the use of this FNN for modeling or solving partial differential equations with periodic boundary conditions. The main advantages of the current approach are the validity of the solution outside the training region, interpretability of the trained model, and simplicity of use.

Fourier decomposition↗
DOE OSTI2025

Tuning Cation (Dis)Order in Cr‐Based Li‐Excess Oxide Cathode Materials to Improve Li+ Transport Properties

Abstract Li‐excess disordered rocksalts (DRXs) hold promise as next‐generation cathodes for Li‐ion batteries due to their high capacity and energy density, along with the potential to eliminate the need for Co and Ni. However, due to their low Li + diffusivity, DRXs need to be pulverized into nanoparticles to achieve high performance. Herein, a new strategy for overcoming this limitation is demonstrated, involving the design of as‐synthesized partially disordered oxides with a structure that lies between ordered layered and fully disordered, exhibiting a varying degree of local (dis)order. This unique structure activates new Li + diffusion channels, improving percolation and transport properties. This strategy allows a large content of Li + to be accessed in material with large, micron‐sized particles through highly reversible Cr 3+/6+ and O redox, yielding a first discharge capacity of 286 mAh g −1 (881 Wh kg −1 ). The Li + percolation network is further improved by substituting Ti with a mixture of multiple metals, which appears to locally decrease the migration barrier through lattice distortion. Proper tuning of the chemical composition, especially the content of metals with empty d orbitals, is established as a crucial factor for controlling the degree of disorder and mitigating voltage fade and hysteresis growth upon cycling.

Moździerz, Maciej↗
DOE OSTI2020

Ni Nanoparticles on CeO 2 (111): Energetics, Electron Transfer, and Structure by Ni Adsorption Calorimetry, Spectroscopies, and Density Functional Theory

The morphology, interfacial bonding energetics and charge transfer of Ni clusters and nanoparticles on slightly-reduced CeO 2-x (111) surfaces at 100 to 300 K have been studied using single crystal adsorption calorimetry (SCAC), low-energy ion scattering spectroscopy (LEIS), Xray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and density functional theory (DFT). The initial heat of adsorption of Ni vapor decreased with the extent of pre-reduction (x) of the CeO 2-x (111), showing that stoichiometric ceria adsorbs Ni more strongly than oxygen vacancies. On CeO 1.95 (111) at 300 K, the heat dropped quickly with coverage in the first 0.1 ML, attributed to nucleation of Ni clusters on stoichiometric steps, followed by the Ni particles spreading onto less favorable terrace sites. At 100 K, the clusters nucleate on terraces due to slower diffusion. Adsorbed Ni monomers are in the +2 oxidation state, and they bind by ~45 kJ/mol more strongly to step sites than terraces. The measured heat of adsorption versus average particle size on terraces is favorably compared to DFT calculations. The Ce 3d XPS lineshape showed an increase in Ce 3+ /Ce 4+ ratio with Ni coverage, providing the number of electrons donated to the ceria per Ni atom. The charge transferred per Ni is initially large but strongly decreases with increasing cluster size for both experiments and DFT, and shows large differences between clusters at steps versus terraces. This charge is localized on the interfacial Ni and Ce atoms in their atomic layers closest to the interface. This knowledge is crucial to understanding the nature of the active sites on the surface of Ni-CeO 2 catalysts for which metal-oxide interactions play a very important role in the activation of O-H and C-H bonds. In conclusion, the changes in these interactions with Ni particle size (metal loading) and the extent of reduction of the ceria help to explain how previously reported catalytic activity and selectivity change with these same structural details.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Anti-Pdc1p Nanobody as a Genetically Encoded Inhibitor of Ethanol Production Enables Dual Transcriptional and Post-translational Controls of Yeast Fermentations

Microbial fermentation provides a sustainable method of producing valuable chemicals. Adding dynamic control to fermentations can significantly improve titers, but most systems rely on transcriptional controls of metabolic enzymes, leaving existing intracellular enzymes unregulated. This limits the ability of transcriptional controls to switch off metabolic pathways, especially when metabolic enzymes have long half-lives. We developed a two-layer transcriptional/post-translational control system for yeast fermentations. Specifically, the system uses blue light to transcriptionally activate the major pyruvate decarboxylase PDC1, required for cell growth and concomitant ethanol production. Switching to darkness transcriptionally inactivates PDC1 and instead activates the anti-Pdc1p nanobody, NbJRI, to act as a genetically encoded inhibitor of Pdc1p accumulated during the growth phase. This dual transcriptional/post-translational control improves the production of 2,3-BDO and citramalate by up to 100 and 92% compared to using transcriptional controls alone in dynamic two-phase fermentations. Furthermore, this study establishes the NbJRI nanobody as an effective genetically encoded inhibitor of Pdc1p that can enhance the production of pyruvate-derived chemicals.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Sustained Oxygen Spectral Gaps and Their Dynamic Evolution in the Inner Magnetosphere

Van Allen Probes observations of ion spectra often show a sustained gap within a very narrow energy range throughout the full orbit. To understand their formation mechanism, we statistically investigate the characteristics of the narrow gaps for oxygen ions and find that they are most frequently observed near the noon sector with a peak occurrence rate of over 30%. The magnetic moment (μ) of the oxygen ions in the gap shows a strong dependence on magnetic local time (MLT), with higher and lower μ values in the morning and afternoon sectors, respectively. Moreover, we find through superposed epoch analysis that the gap formation also depends on geomagnetic conditions. Those gaps formed at lower magnetic moments (μ < 3,000 keV/G) are associated with stable convection electric fields, which enable magnetospheric ions to follow a steady drift pattern that facilitates the gap formation by corotational drift resonance. On the other hand, gaps with higher μ values are statistically preceded by a gradual increase of geomagnetic activity. Here, we suggest that ions within the gap were originally located inside the Alfven layer following closed drift paths, before they were transitioned into open drift paths as the convection electric field was enhanced. The sunward drift of these ions, with very low fluxes, forms a drainage void in the dayside magnetosphere manifested as the sustained gap in the oxygen spectrum. This scenario is supported by particle-tracing simulations, which reproduce most of the observed characteristics and therefore provide new insights into inner magnetospheric dynamics.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Precision surface modification of solid oxide fuel cells via layer-by-layer surface sol–gel deposition

While solid oxide fuel cells (SOFCs) are a promising technology for a clean and sustainable future, their commercialization is hindered by limited durability and performance. Here, we report our findings on the application of a layer-by-layer surface sol–gel (SSG) coating of catalysts to dramatically enhance the electro-catalytic activity and durability of SOFC cathodes. The SSG process is capable of penetrating and preserving complex backbone microstructures of porous electrodes, creating highly conformal coatings of controlled morphology, while tailoring the composition of the surface to improve catalytic properties and durability. For example, the application of an SSG coating of PrO x to a La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ (LSCF) cathode has reduced the polarization resistance from 1.136 to 0.117 Ω cm 2 at 600 °C and the degradation rate from 1.13 × 10 –3 to 2.67 × 10 –4 Ω cm 2 h –1 at 650 °C. In addition, a continuous improvement in electrode performance is demonstrated as the thickness of the coating is increased, corresponding to the linear addition of catalyst. Furthermore, this first application of the SSG technique to SOFC systems opens the door for the controlled surface modification of porous components in electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Compromise of Personal Protective Clothing from Liquid Exposure

Following critiques of multiple personal contamination events from entries into the Oak Ridge National Laboratory’s Spallation Neutron Source transfer bay, it was considered that the most likely causes for contamination were personal protective clothing doffing errors or that moisture (sweat) allowed contamination to wick through the protective clothing. To pursue this issue, radiological protection staff looked more closely, however, at the specific area of the clothing where contamination was highest; under enhanced lighting and photochromic manipulation, there appeared to have been some type of moisture in the area. Recognizing the possibility that moisture may have allowed for migration of contamination through the clothing, further experiments were undertaken to determine under which conditions this transport might have occurred. The objective for this work was to identify the susceptibility of different types of personal protective clothing to various liquids encountered in the workplace.Method: Several tests were performed to determine if perspiration had enabled migration of contamination, and to identify what other liquids might have affected contamination transport. Two layers of personal protective clothing were subjected to static conditions and dynamic conditions, to include active rubbing of the materials while wet. Food dye added to each of the liquids tested enabled visual indications of liquid breakthrough. Additional tests were conducted to see if solid contamination could be transported through the materials along with the liquids. As a result, it was found that all but one type of non-rubberized personal protective clothing in use at Oak Ridge National Laboratory were permanently compromised to some extent by the solvents used for decontamination. It was determined that most common cleaning agents immediately and permanently destroyed the hydrophobic nature of several of the splash-resistant protective clothing materials, allowing for radioactive contamination to penetrate through the material to the worker. Work around wet surfaces or performing wet decontamination will only be performed in protective clothing known to prevent transport of the wetting agent.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2025

Data for "Anti-Pdc1p Nanobody as a Genetically Encoded Inhibitor of Ethanol Production Enables Dual Transcriptional and Post-translational Controls of Yeast Fermentations"

Microbial fermentation provides a sustainable method of producing valuable chemicals. Adding dynamic control to fermentations can significantly improve titers, but most systems rely on transcriptional controls of metabolic enzymes, leaving existing intracellular enzymes unregulated. This limits the ability of transcriptional controls to switch off metabolic pathways, especially when metabolic enzymes have long half-lives. We developed a two-layer transcriptional/post-translational control system for yeast fermentations. Specifically, the system uses blue light to transcriptionally activate the major pyruvate decarboxylase PDC1 , required for cell growth and concomitant ethanol production. Switching to darkness transcriptionally inactivates PDC1 and instead activates the anti-Pdc1p nanobody, NbJRI, to act as a genetically encoded inhibitor of Pdc1p accumulated during the growth phase. This dual transcriptional/post-translational control improves the production of 2,3-BDO and citramalate by up to 100 and 92% compared to using transcriptional controls alone in dynamic two-phase fermentations. This study establishes the NbJRI nanobody as an effective genetically encoded inhibitor of Pdc1p that can enhance the production of pyruvate-derived chemicals.

metabolic engineering↗
DOE OSTI2026

High fidelity actuator line data from 9 turbine wind farm simulations using ExaWind

This data was generated with the ExaWind code suite (https://github.com/Exawind) to investigate the performance of different Active Wake Mixing turbine control in a wind farm situated in a stable atmospheric boundary layer. All cases correspond to a 3x3 wind farm in a 10km x 10km domain using a total mesh size that varied between 1.6 X 10^9 to 1.85 X 10^9 grid cells. The simulations were run across 1800-2000 GPUs on Frontier. The case description and data generation process is fully documented in Yalla, G. R., Brown, K., Cheung, L., Houck, D., deVelder, N., and Balaji, J. (2025). "Estimating annual energy production of wake mixing control strategies including comparisons to wake steering." Wind Energy Sciences (https://doi.org/10.5194/wes-2025-250).

17 WIND ENERGY↗
DOE OSTI2022

Layer Time Control for Large Scale Additive Manufacturing Using High Performance Computing

This work proposes to optimize an additive manufacturing AM process to reduce energy and printing cost. The polymer AM process is inherently dependent on the time-temperature history of each layer to maintain geometric tolerances and mechanical integrity. Our preliminary study shows that regression-based layer time control model using thermal images could result in up to 30% build time reduction for simple geometries. This proposed work would use high-performance computing (HPC) to couple the data-driven model with thermal simulation for better predicting layer temperature profiles, improving throughput of large-scale additive manufacturing, and reducing its energy cost. We have developed a method to optimize a layer deposition time (a.k.a. layer time) for large-scale AM via physics-based simulations. A long layer time leads to an over-cooled surface on which a new layer is deposited, and therefore, it may result in a weak bonding or debonding between layers, cracking, or warping. A short layer time leads to a high temperature of the structure due to insufficient cooling, and therefore, the structure may not be stiff enough and may collapse during manufacturing. Therefore, it is important to estimate the optimal layer time in additive manufacturing for a high-quality product. The temperature of a top layer right before deposition is recommended to be slightly higher than the glass temperature of the material. A temperature cooling was approximated to an exponential function of time, and the optimized layer time was obtained based on a target temperature while maintaining a minimal printing time. The material used is carbon fiber-reinforced polycarbonate (CF/PC), and the large-scale deposition system used is LSAM TM from Thermwood Corporation. Three different layer time cases were used for experiments, and a series of thermal images were obtained via an infra-red (IR) camera during the entire AM processes. AM process simulations were performed using a finite element method and the temperature profiles from the simulation were in good agreements with those from experiments. The layer time optimization was performed based on the temperature profiles from the simulations. A layer temperature with the optimal layer time was confirmed as the target temperature through simulation. In addition to the development of a layer time optimization method, we have developed a numerical framework for AM simulation with element activations in sync with toolpath, based on an open source finite element framework, DEAL.II. A major portion of this work was presented at SAMPE 2022 Conference and Exhibition on May 2022, and published in Proceedings of SAMPE 2022.

42 ENGINEERING↗
DOE OSTI2023

NanoMechanics: Elasticity and Friction in Nano‐Objects

A large scientific and technological effort is underway to investigate the properties of two‐dimensional (2D) materials to become building blocks in integrated nano‐electronic and photonic circuits, composites, coatings, energy harvesting nano‐ systems, nano‐sensors, and nano‐electro‐mechanical systems (NEMS).While several experiments and calculations have revealed exciting novel phenomena in these nanostructures, many scientific and technological questions remain open. In particular, understanding and controlling the structure and mechanical properties of 2D materials at the interface with a solid surface is of key importance to enable the aforementioned nanotechnologies, as well as to fulfill the potential of strain engineering to tailor their properties. The vision of this DoE research program was to investigate novel mechanical properties and phenomena in 1D and 2D materials with the overarching goal of defining a new basic understanding of mechanical behavior in nano and quantum systems. The group of the PI has developed in the last years several studies on the mechanical properties of Carbon nanotubes and oxide nanobelts, more recently the PI has focused her attention on the properties of two‐dimensional materials, such as graphene and MoS 2 , which are a few‐atomic‐layer thick films and hold a great potential for technological and energy applications. The most studied 2D material is graphene, existing as a single layer of graphite or a few‐layer thick epitaxial graphene film. Graphene possesses a large in‐plane Young’s modulus as well as high intrinsic carrier mobility, and high in‐plane thermal conductivity. Besides graphene, also 2D films of graphene oxide (GO), hexagonal Boron Nitride (h‐BN), and transition metal dichalcogenides such as MoS 2 exhibit unique and excellent properties and hold great promise for nanotechnology applications. This research program was aimed at developing a new basic understanding of the mechanical properties of 1D and 2D materials at the interface with solid substrates, with a focus on the role of defects, materials structure, and substrate interaction. Ultimately, we aimed at developing the basic knowledge and experimental tools for manipulating 1D and 2D materials’ structure, stacking, substrate interaction, defects, and number of layers to realize an entirely new class of ultra‐hard, ultra‐thin, and ultra‐light active materials with ad‐ hoc mechanical properties for a variety of applications.

2D Materials↗
DOE OSTI2025

STILGAR: Subsurface Models for Graymont Pleasant Gap Mine

The detection, location, and monitoring of underground structures are of great importance to national and global security. Tunnels and voids generate seismic signatures detectable at the surface, but using non-invasive seismic data to image near-surface presents several challenges in real-world applications. In this report, we describe the use of a dense surface seismic deployment to generate subsurface models of the Graymont Pleasant Gap mine - a single-layer mine with a complex structure embedded in a high-velocity P-wave limestone bedrock. Our approach consists of three key methods. We use P-wave arrival times from local blast events to perform a tomography inversion with the tomoTD method, constructing a P-wave velocity model of the subsurface. We model the layer above the mine using Rayleigh wave ellipticity and inversion techniques. We leverage ongoing anthropogenic activities to identify and locate noise sources both on the surface and within the subsurface. With this integrated approach we aim to overcome the challenges and enhance our ability to non-invasively characterize underground structures, contributing to improved seismic monitoring techniques.

58 GEOSCIENCES↗
DOE OSTI2020

Atomic Layer Deposition for Enhanced Reactivity, Stability, and Sulfur Tolerance of Hydrogenation Catalysts

Heterogeneous catalysts are an essential tool in the transition towards a sustainable, bio-based economy for fuels and chemicals. However, many key biomass conversion processes utilize harsh conditions that lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Active site poisoning resulting from the relatively high sulfur content of most biomass feedstocks further compounds these durability problems. Next-generation catalysts must be developed to address these stability challenges. In this work, we have used atomic layer deposition (ALD), to modify a conventional Pd/Al2O3 hydrogenation catalyst and generate improvements in its stability and sulfur tolerance, as well as overall catalyst activity. Ten cycles of TiO2ALD were applied to Pd/Al2O3 using a proprietary coating process developed by industry partners. The coated catalyst (10cTiO2), alongside uncoated Pd/TiO2 and Pd/Al2O3 controls, was characterized in-depth and naphthalene hydrogenation was used as a probe reaction to assess activity. The 10cTiO2 catalyst was observed to be significantly more active towards hydrogenation than uncoated Pd/Al2O3, despite evidence that the ALD coating suppressed chemisorption uptake through coverage of Pd. In order to reconcile these seemingly contradictory findings, interactions between the Pd nanoparticles and TiO2ALD coating were investigated via XAS and computational modeling. The catalysts were also assessed for their sulfur tolerance, thermal stability, and hydrothermal stability. Each of these catalyst stability parameters was enhanced by application of the TiO2ALD layer; the mechanisms by which the layer may have mitigated these degradation processes will be discussed. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of the expected and unexpected benefits of applying TiO2ALD coatings to supported Pd hydrogenation catalysts.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗