Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Cold-air performance of a 15.41-cm-tip-diameter axial-flow power turbine with variable-area stator designed for a 75-kW automotive gas turbine engine

An experimental evaluation of the aerodynamic performance of the axial flow, variable area stator power turbine stage for the Department of Energy upgraded automotive gas turbine engine was conducted in cold air. The interstage transition duct, the variable area stator, the rotor, and the exit diffuser were included in the evaluation of the turbine stage. The measured total blading efficiency was 0.096 less than the design value of 0.85. Large radial gradients in flow conditions were found at the exit of the interstage duct that adversely affected power turbine performance. Although power turbine efficiency was less than design, the turbine operating line corresponding to the steady state road load power curve was within 0.02 of the maximum available stage efficiency at any given speed.

Mclallin, K. L.↗
NASA NTRS1982

Three-dimensional flow field in the tip region of a compressor rotor passage. II - Turbulence properties

The turbulence properties in the annulus wall region of an axial flow compressor rotor was measured using a triaxial, hot-wire probe rotating with the rotor. The flow was surveyed across the entire passage at five axial locations (leading edge, 1/4 chord, 1/2 chord, 3/4 chord, and the trailing edge location) and at six radial locations in a low-speed compressor rotor. The data derived include all three components of turbulence intensity and three components of turbulence stress. A comprehensive interpretation of the data with emphasis on features related to rotation, leakage flow, annulus wall boundary layer, and blade boundary layer interactions is included. All the components of turbulent intensities and stresses are found to be high in the leakage-flow mixing region. The radial component of intensities and stresses is found to be much higher than the corresponding streamwise components. The turbulent spectra clearly reveal the decay process of the inlet-guide-vane wake within the rotor passage.

Lakshminarayana, B.↗
NASA NTRS1983

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗
NASA NTRS1983

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗
NASA NTRS1983

Wall boundary layer development near the tip region of an IGV of an axial flow compressor

The annulus wall boundary layer inside the blade passage of the inlet guide vane (IGV) passage of a low-speed axial compressor stage was measured with a miniature five-hole probe. The three-dimensional velocity and pressure fields were measured at various axial and tangential locations. Limiting streamline angles and static pressures were also measured on the casing of the IGV passage. Strong secondary vorticity was developed. The data were analyzed and correlated with the existing velocity profile correlations. The end wall losses were also derived from these data.

Lakshminarayana, B.↗
NASA NTRS1984

Thematic Mapper Image Processing System (TIPS) Processing Status

Radiometric and geometric correction performance is considered. A one quantum level requirement was met in all spectral bands with an occasional band 7 exception. Initial post launch calibration was accomplished. An absolute radiometric calibration is in progress including an investigation of low impact solution to scan striping. Initial and three downstream updates as well as coordination with LANDSAT D' instrument calibration are planned. Methods and problems in measuring geometric correction performance are examined with an emphasis on temporal registration, geodetic registrtion, and the modeling error budget. Planned efforts include eliminating band 2, band 5 chips; continued performance monitoring; calibration of profile, misalignment angles, and filer parameters; studying the need for seasonal geodetic control points; and improvement of the subpixel correlation technique.

Brooks, J.↗
NASA NTRS1982

Advanced blade tip seal system, volume 2

The results of the endurance and performance engine tests conducted on monocrystal/abrasive-tipped CF6-50 Stage 1 HPT blades fabricated in Task VII of MATE Project 3 are presented. Two engine tests are conducted. The endurance engine test is conducted for 1000 C cycles. The performance engine test is conducted on a variable cycle core engine. Posttest evaluation and analyses of the blades and shrouds included visual, dimensional, and destructive evaluations.

Zelahy, J. W.↗
NASA NTRS1985

Experimental study of ceramic coated tip seals for turbojet engines

Ceramic gas-path seals were fabricated and successfully operated over 1000 cycles from flight idle to maximum power in a small turboshaft engine. The seals were fabricated by plasma spraying zirconia over a NiCoCrAlX bond boat on the Haynes 25 substrate. Coolant-side substrate temperatures and related engine parameters were recorded. Post-test inspection revealed mudflat surface cracking with penetration to the ceramic bond-coat interface.

Biesiadny, T. J.↗
NASA NTRS1980

Verification of the SRB motor case pin retainer band tips

The pin retainer band is a 1-1/4 in. wide by about 1/32 in. thick steel band that is stretched over the pins circumferentially at the joints of the solid rocket booster (SRB) motor case segments. Its purpose is to hold the retaining pins in place during flight. Since the band is thin and is mounted stretched, or under tension, over the pins which are greased in place, it is necessary to protect it thermally. Three typical areas of the band location on the SRB motor case joints were chosen for verifying the cork thermal prection system (TPS) performance on the band: the joint in front of the attach ring, at the aft skirt joint in front of the kick ring and in an unperturbed area at the forward segments of the SRB motor cases. The kick ring area pin retainer band cork TPS passed the test requirements in the region where there are no phenolic splice caps. In the splice cap areas where the band TPS is closed out around the splice with K5NA, additional amounts of K5NA material is required to adequately protect the steel band. TPS requirements were easily met in the one location where the ends of the steel band are joined together after installation and tensioning. The attack ring area pin retainer band TPS did not quite pass the heat load requirements with the .375 in. thick cork TPS as used for the kick ring area band. It is recommended that the cork thickness here be increased to .50 in. The unperturbed area band TPS presented no problems.

Karu, Z. S.↗
NASA NTRS1985

Postlaunch corrections for Thematic Mapper 5 (TM-5) radiometry in the Thematic Mapper Image Processing System (TIPS)

The paper discusses postlaunch corrections made to the calibration lamp radiance values for band 3 of TM-5 (Thematic Mapper instrument on Landsat-5). It is hypothesized that the low in-orbit temperatures have caused the shutter arm to contract slightly, causing the detectors to view the lamps through different parts of the lens system. Owing to unevenness in the lenses this is introducing an odd-even channel discrepancy in the computed gains, resulting in striped imagery. The process used to compute the new values is presented along with supporting data and the old and new radiance numbers. The new values solve the relative radiometric correction problem of striping. However, the effect on the absolute radiometric correction performance is not quantitatively known.

Singh, A.↗
NASA NTRS1985

Experimental study of ceramic-coated tip seals for turbojet engines

Ceramic gas-path seals were fabricated and successfully operated over 1000 cycles from flight idle to maximum power in a small turboshaft engine. The seals were fabricated by plasma spraying zirconia over a NiCoCrAlX bond coat on the Haynes 25 substrate. Coolant-side substrate temperatures and related engine parameters were recorded. Post-test inspection revealed mudflat surface cracking with penetration to the ceramic bond-coat interface.

Biesiadny, T. J.↗
NASA NTRS1985

Model helicopter blade slap at low tip speeds - Theoretical and experimental correlations

A novel data acquisition system has been designed which allows a transfer of pressure transducer and hot film data from a rotating frame to a stationary one, while collecting both loading and far field acoustic measurements simultaneously; this permits correlations to be made between experimental and theoretical predictions of blade loads and the resulting far field acoustics. The comparison of predicted acoustic pulse with experimental measurements has verified the assumptions made in the Widnall and Wolf (1980) theory for the case of low speed incompressible flow. The theory is also shown to be very sensitive to the interaction geometry and trajectory of the blade trailing vortex.

Chan, D. C.-L.↗
NASA NTRS1986

Calculation of helicopter airfoil characteristics for high tip-speed applications

In this paper, we have applied a new aerodynamic tool to the study of helicopter airfoil characteristics. We have shown that the computed airloads reproduce completely the experimental behavior of representative airfoils across the transonic regime. In addition, the computational details of the flow fields, the surface pressure distributions, and the viscous-layer characteristics enable us to trace the evolution of the physical changes that occur as m infinity or Re increases. Descriptions of the complicated development of shock waves, shock-induced separation supplement the information that has been obtained heretofore in wind tunnels. In validating our calculations and assessing the accuracy of the results, including extensive grid-refinement studies and comparisons with data from numerous wind tunnels, we have defined the capabilities and limitations of the code ARC2D more precisely. This important aspect of the investigations can complement wind-tunnel tests, by providing flow-field details that are difficult to measure and by extending the range of low parameters beyond the capabilities of existing wind tunnels. The code has now progressed from a purely research stage to almost a production stage, where it can be run by specialists in the helicopter industry.

Mccroskey, W. J.↗