Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Test Pilots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Effects of nozzle design parameters on the extent of quiet test flow at Mach 3.5

Tests results at the NASA Langley Research Center, involving a Mach 3.5 pilot quiet tunnel, have shown that laminar-layered nozzle walls improve boundary layer stability and reduce stream disturbance levels caused by eddy Mach wave radiation. This type of wall design is required to obtain transition Reynolds numbers on tests models as high as those previously observed in supersonic flight vehicles. The Mach 3.5 pilot nozzle wall boundary layers were tested for Tollmein-Schlichting and Goertler linear amplification, and, in an analysis of Goertler vortices in two axisymmetric Mach 5 nozzles, transition values were found to vary. These values were applied to several nozzles with similar throat heights but different expansion rates. Among the nozzles included in the study, a flat-wall radial flow nozzle and a proposed rod-wall nozzle were tested. For the highest test unit Reynolds number, it was determined that the nozzle wall surface finish should not exceed 0.3 micron. Oil flow studies have indicated that Goertler vortex disturbances were the dominant mechanism causing transition on the walls of the pilot nozzle.

Beckwith, I. E.↗
NASA NTRS2010

High-Volume Airborne Fluids Handling Technologies to Fight Wildfires

NASA recently partnered with the U.S. Forest Service (USFS) on a project to examine mission suitability and recommend policies and procedures for the use of very large aerial firefighting aircraft such as the Boeing 747 and DC-10 aerial retardant delivery aircraft. The aircraft under study included a 10Tanker DC-10 and an Evergreen B-747. NASA's Dryden Flight Research Center and Ames Research Center worked with the USFS to help determine the safe flight envelope for these Very Large Air Tanker (VLAT) aircraft for the USFS and the Department of the Interior (DOI). This new generation of supertankers includes aircraft like these that have as much as four times the delivery capacity of the previous generation of aerial firefighting aircraft. Dryden performed operational test and evaluation assessments and reported findings and recommendations on these aircraft in cooperation with Ames. The team developed, implemented, and directed an evaluation test plan for use in flight test and in simulation. Ames provided support using pilot-in-the-loop simulations and coordinated simulator models, flight profiles, and data analysis with Dryden. The test plan was designed to evaluate the suitability of VLAT aircraft as a function of mission environment. Based on this analysis, NASA generated interim flight envelope limitations to enhance safety and operational utility in the fire-retardant delivery mission. These recommended flight limitations were adopted by the USFS. The 10Tanker DC-10 has been in use for several years with the California Department of Forestry and Fire Protection(Cal-Fire), but until NASA took on the challenge of reviewing VLAT capabilities and limitations, the USFS was hesitant to add them to the federal wildfire arsenal. The DC-10 delivery system is based on an externally mounted set of tanks and a bomb-bay style set of clamshell doors that are opened in precisely calibrated ways to deliver the amounts and concentrations of retardant called for by the specific wildfire situation. The system was manufactured by Jordan Air of Central Point, OR, and was installed by Victorville Aerospace in Victorville, CA. It can deliver 12,000 gallons (45.4 kL) of retardant in as little as eight seconds. The aircraft can deliver a partial load of retardant and make multiple drops on the same flight, or the entire load can be rapidly delivered in one pass if required for maximum coverage. The Evergreen 747 uses internal tankage and a pressurized delivery system to enable volume and coverage levels that also meet USFS requirements, but enables computer control of flow for desired precision. This system was designed and built by Adaptive Aerospace of Tehachapi, CA and can deliver about 20,000 gallons (75.7 kL) of retardant in approximately ten seconds. The 747 can also make multiple independent drops, or deliver the entire load at once. NASA found that both of these VLAT aircraft are compatible with the wildfire suppression mission when used to supplement other aerial retardant delivery platforms. The major recommendations for deployment that resulted from this study relate to terrain clearance, the type of terrain in the drop area, availability of qualified lead planes to guide the VLAT approach to the drop area, and low-altitude maneuvering limitations. NASA s analysis suggests that with the appropriate flight procedures, these aircraft will provide a powerful set of tools to fight wildfires.

Dickerson, Mark↗
NASA NTRS1986

Flying complex approach paths using the microwave landing system

A piloted simulation study was conducted to examine the requirements for using electromechanical flight instrumentation to provide guidance for manually controlled flight along complex, curved approach paths within the microwave landing system signal coverage. The data from these tests indicated that flight director guidance is required for the manually controlled flight of a jet transport airplane on complex, curved approach paths. Each of the three guidance algorithms tested could be used to fly the paths. However, pilot comments indicated that the use of guidance based on capturing the next straight path segment may not be acceptable since full-scale lateral deflections normally resulted during turns. Pilot comments indicated that all the approach paths tested could be used in normal airline operations. Approach paths with both multiple, sequential turns and short final path segments were demonstrated.

Knox, Charles E.↗
NASA NTRSDate not supplied

Manual Crew Override of Vehicle Landings Following G-Transitions

BACKGROUND Manual control during exploration spaceflight consists of both planned automated supervisory control and unplanned crew override. This crew override capability is critical to enable overall mission success during landing contingencies. However, the introduction of manual override capabilities must be implemented to enable crews to mitigate risks introduced by human error. Adaptive changes in the sensorimotor system can manifest during g-transitions as spatial disorientation. While training and landing aids enable successful landing through disorientation, these adaptive changes may increase cognitive demand that needs to be accounted for in the manual control strategy. It is important to characterize these effects as soon as possible following the G-transition to develop appropriate countermeasures. METHODS In this study, we will examine operational piloting tasks following International Space Station (ISS) missions in a simulated lunar landing using a six-degree-of-freedom (6DOF) motion base. The motion-based simulation will be implemented in our laboratory at the Johnson Space Center (JSC) and will be available within hours following the return from commercial crew landings. The primary goals of this study are (1) to understand the impact of spaceflight on crew ability to perform manual crew override tasks, (2) to examine how adaptive changes in vestibular and cognitive function relate to changes in manual crew override proficiency, and (3) compare performance during late “just-in-time” on-board training with early post-flight crew performance. The impact of spaceflight on piloting capability will be assessed from pre- versus post-flight changes in crewmembers assigned to either short duration (< 30 day) or long duration (~6- month) missions to the International Space Station (ISS). Individual differences in post-flight vestibular and cognitive changes include motion sickness reports, measures of tilt motion perception accuracy and precision, and dual-task tracking. During the 6DOF lunar simulation, the crew will manually takeover attitude and rate-of-descent to the nominal or re-designated landing aim point during the approach phase. The outcome measures for the lunar crew override tasks will be the percent time maintaining actual vehicle states, e.g., attitude and rate-of-descent, within recommended guidance during the landing approach, number and maximum deviation outside limits, and root mean square error (RMSE). Given that “just-in-time” (JIT) training is an operational expectation for the Human Landing System (HLS) program, all participants will perform late inflight JIT training for each manual crew override task in which they will participate. Crew proficiency will be captured inflight during JIT training that will be implemented on a laptop with hand controllers to allow the crewmember to practice the landing task procedures like the approach implemented for JIT training with Shuttle landing and ISS telerobotic tasks. COUNTERMEASURE UPDATES The lunar lander simulation has been implemented onto a two-laptop display system where subjects select from alternative landing points, based upon avoiding hazards that the on-board system identifies during the landing. The subject makes inputs using a rotational hand controller (i.e., joystick) and a translational hand controller, which are processed by simulated vehicle dynamics to update the vehicle attitude and rate of descent. Subjects will utilize a combination of flight, situation, and status displays to monitor the state of the simulated vehicle. The simulation exports tilt and translation movements to a 6DOF motion base synced to visual movements and provides representative vestibular cues to the subject while performing the task inside an enclosed cabin featuring a simulated lunar out-the-window view and a heads-down lander cockpit view. RELEVANCE This project will deliver an operational demonstration of crew override capability following spaceflight and identify potential deficits that may require remediation. Comparison of individual vestibular and cognitive changes with crew override performance will help better characterize the manual control risks associated with sensorimotor alterations. The inclusion of “just-in-time” on-board training will ensure we are characterizing changes in override proficiency with this expected countermeasure in place. ACKNOWLEDGEMENTS: The authors acknowledge contributions from Draper, HLS Joint Test Panel, Crew HLS Interfaces for Piloting Working Group, and Dynamic Skills Trainer (DST) Lab toward the development of the lunar landing simulation. This project is funded by the Human Health Countermeasures Element.

Austin M Bollinger↗
NASA NTRS2010

Heat Flux and Wall Temperature Estimates for the NASA Langley HIFiRE Direct Connect Rig

An objective of the Hypersonic International Flight Research Experimentation (HIFiRE) Program Flight 2 is to provide validation data for high enthalpy scramjet prediction tools through a single flight test and accompanying ground tests of the HIFiRE Direct Connect Rig (HDCR) tested in the NASA LaRC Arc Heated Scramjet Test Facility (AHSTF). The HDCR is a full-scale, copper heat sink structure designed to simulate the isolator entrance conditions and isolator, pilot, and combustor section of the HIFiRE flight test experiment flowpath and is fully instrumented to assess combustion performance over a range of operating conditions simulating flight from Mach 5.5 to 8.5 and for various fueling schemes. As part of the instrumentation package, temperature and heat flux sensors were provided along the flowpath surface and also imbedded in the structure. The purpose of this paper is to demonstrate that the surface heat flux and wall temperature of the Zirconia coated copper wall can be obtained with a water-cooled heat flux gage and a sub-surface temperature measurement. An algorithm was developed which used these two measurements to reconstruct the surface conditions along the flowpath. Determinations of the surface conditions of the Zirconia coating were conducted for a variety of conditions.

Cuda, Vincent, Jr.↗
DOE OSTI2021

An industrial perspective on catalysts for low-temperature CO 2 electrolysis

Electrochemical conversion of CO 2 to useful products at temperatures below 100 °C are nearing the commercial scale. Pilot units for CO 2 conversion to CO are already in testing. Units to convert CO 2 to formic acid are projected to reach pilot scale in the next year. Further, several investigators are starting to observe industrially relevant rates of the electrochemical conversion of CO 2 conversion to ethanol and ethylene with the needed hydrogen coming from water. In each case, Faradaic efficiencies of 80% or more and currents above 200 mA/cm –2 can be reproducibly achieved. In this study we describe the key advances in nano catalysts that lead to the impressive performance, indicate where additional work is needed and provide benchmarks that others can use to compare their results.

10 SYNTHETIC FUELS↗
NASA NTRS2013

Pre-Study Walkthrough with a Commercial Pilot for a Preliminary Single Pilot Operations Experiment

The number of crew members in commercial flights has decreased to two members, down from the five-member crew required 50 years ago. One question of interest is whether the crew should be reduced to one pilot. In order to determine the critical factors involved in safely transitioning to a single pilot, research must examine whether any performance deficits arise with the loss of a crew member. With a concrete understanding of the cognitive and behavioral role of a co-pilot, aeronautical technologies and procedures can be developed that make up for the removal of the second aircrew member. The current project describes a pre-study walkthrough process that can be used to help in the development of scenarios for testing future concepts and technologies for single pilot operations. Qualitative information regarding the tasks performed by the pilots can be extracted with this technique and adapted for future investigations of single pilot operations.

Single Pilot Operations↗
DOE OSTI2023

Small Business Voucher Program: Scaling-Up of Bio-Based C5 Building Block Production: Cooperative Research and Development Final Report, CRADA Number CRD-16-00611

Visolis, Inc. is an early stage industrial biotechnology company developing next generation of processes for producing building blocks for bulk polymers and fuels. The company is developing low-cost routes to the chemicals of the future in support of DOE, EERE and BETO goals to grow the U.S. bioeconomy. NREL has capabilities in scale-up of fermentation processes from bench top through pilot scales and also has expertise and technologies related to production of lignocellulosic sugars from cellulosic feedstocks. NREL's Integrated Biorefinery Research Facility (IBRF) houses multiple fermentation vessels/systems ranging in size from 0.5 to 9,000 L along with ancillary capabilities in compositional analysis, separations, and purification. NREL's role will be to scale-up the Visolis process to produce an intermediate product, mevalonic acid, from both dextrose and biomass derived sugars. The goals of the project are to: 1) transfer and reproduce one of Visolis's proprietary fermentation processes at bench top and pilot scale at NREL's IBRF using dextrose as the feedstock, 2) carry out bench-scale fermentations using Visolis's organism and cellulosic sugars, and 3) produce mevalonic acid from the bench top and pilot scale runs for catalyst lifetime testing and conversion to isoprene.

09 BIOMASS FUELS↗
DOE OSTI2022

CRADA Number NFE-18-07313 with Nth Cycle, Inc. (CRADA Final Report)

Cooperative Research and Development Agreement (CRADA) NFE-18-07313 between Oak Ridge National Laboratory (ORNL) and Nth Cycle Inc. focused on developing a technology for sustainable recycling of rare earth and specialty metals (e.g., Y, Co, Li; RESE), as well as bulk and precious metals from industrial manufacturing and waste streams through the use of electrochemical carbon nanotube-enabled filters. The project outcome was expected to be a stronger mechanistic understanding of the electrochemical recovery of metals from real manufacturing process streams and e-waste streams, and the development of an optimized high-throughput pilot-scale device ready for commercialization. Testing, design, and development of a v1 prototype to prove the technology was unsuccessful (we were not able to reach the go/no-go outlined in Objective 1) and we were unable to continue our redesign due to COVID-19 lockdown and no access to lab from March 2020 – until our graduation from the program.

36 MATERIALS SCIENCE↗
NASA NTRS1973

A technique for measuring hypersonic flow velocity profiles

A technique for measuring hypersonic flow velocity profiles is described. This technique utilizes an arc-discharge-electron-beam system to produce a luminous disturbance in the flow. The time of flight of this disturbance was measured. Experimental tests were conducted in the Langley pilot model expansion tube. The measured velocities were of the order of 6000 m/sec over a free-stream density range from 0.000196 to 0.00186 kg/cu m. The fractional error in the velocity measurements was less than 5 percent. Long arc discharge columns (0.356 m) were generated under hypersonic flow conditions in the expansion-tube modified to operate as an expansion tunnel.

Gartrell, L. R.↗
NASA NTRS1973

Free-stream temperature, density, and pressure measurements in an expansion tube flow

An experimental study was conducted to determine test-flow conditions in the Langley pilot model expansion tube. Measurements of temperature, density, wall pressure, pitot pressure, and shock and interface velocities were compared with theoretical calculations based on various models of the flow cycle. The vibrational temperature and integrated density of the molecular oxygen component of the flow were measured by use of vacuum ultraviolet absorption techniques. These measurements indicate both the presence and possible degree of nonequilibrium in the flow. Data are compared with several simplified models of the flow cycle, and data trends are discussed.

Haggard, K. V.↗
NASA NTRS1974

Investigation of an anomalous flow condition of the Langley pilot model expansion tube

Free-stream flow velocity measurements were made in the Langley pilot model expansion tube during the test flow interval. During this interval, an anomalous dip in pitot pressure occurs for the expansion tube operating conditions employed. Within the test flow interval, the main conclusions reached from comparison of the measured flow velocity, pitot pressure, and tube wall pressure are: the variations which occur in velocity and wall pressure are small compared with the variations in pitot pressure; a corresponding dip in the derived flow density is associated with the dip in pitot pressure; and the value of the average density over the interval, which results from the expansion from the shocked intermediate chamber condition, is approximately one-half of the value that can result from only an isentropic process.

Friesen, W. J.↗
NASA NTRS1981

Diversity techniques for omnidirectional telemetry coverage of the HiMAT research vehicle

The highly maneuverable aircraft technology (HiMAT) remotely piloted research vehicle (RPRV) was flight tested and a number of technological advances applicable to future fighter aircraft were demonstrated. The aircraft control system uses airborne and ground-based computers which communicate via uplink and downlink telemetry. Antenna radiation patterns are normally much less than ideal for continuous reception or transmission for all aircraft attitudes. After flight qualification and testing on other aircraft, a frequency diversity concept and an antenna diversity concept were implemented on the HiMAT vehicle to obtain omnidirectional telemetry coverage.

Harney, P. F.↗
NASA NTRS1980

HiMAT systems development results and projections

Significant findings of the Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) flight test program are presented. Among the topics covered are: aerodynamic scaling relationships, the aeroelastic tailoring of wing and canard twist and camber, and laminate graphite/epoxy composite primary structure performance under high-g loading maneuvers. Attention is also given to the set of actuators used in the test and development program, with a view to the minimization of costs through modularity and interchangeability of components and the extensive use of off-the-shelf equipment. The relationship between composite ply geometry and the shape and magnitude of aeroelastic deformations during maneuvering is discussed in detail.

Brown, L. E., Jr.↗