SEARCH · Engineering Papers

Results for “Subsurface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Thermal Infrared Observations of Lava Flows During the 1984 Mauna Loa Eruption

Thermal infrared videotape images of the flowing lava streams and the vent areas at 10.6 microns were made, as well as some broadband images in the 8 to 12 micron range (for gas plume detection). These data were calibrated with on-site hand-held radiometer measurements, in-flow thermocouple measurements, and with later laboratory kiln measurements. Infrared video data are useful in quantitatively assessing the pattern and mode of flow thermal losses, particularly with regard to radiative losses from established/incipient floating crust. The general cooling of the flows downstream was readily apparent. Upper reaches of the active flow exhibited nearly crust-free main channels, radiating at about 700 to 800 degrees C. Below about the 7500 foot level (about 8 km from the vent) the flows formed nearly continuous crust and tended to spread, become less well-defined and founder due to a reduction in slope. Nevertheless, in thermal IR observations, the surface trace of the active subsurface channel was visible, radiating at about 500 to 700 degrees C. At the active flow front, most solid crust radiated at temperatures less than 500 to 600 degrees C, however bright high temperature interiors (approximately 900 to 1000 degrees C) were clearly visible though evolving fissures.

Pieri, D. C.↗

NASA NTRS1985

Hydrovolcanism

Hydrovolcanism is a common phenomena produced by the interaction of magma or magmatic heat with an external source of water, such as a surface body, an aquifer, or a glacier. The effects include hydrofracture of existing rock units in the subsurface and the formation of hyaloclastites in a subaqueous environment. Hydroexplosions originate within a few kilometers of the surface. They may be relatively small, phreatic events or devastating complex blasts. Large-scale experiments determined that the optimal mixing ratio of water to basaltic melt (thermite plus silicates) for efficient conversion of thermal energy into mechanical energy is in the range of 0.1 to 0.3. Based on experimental results, eruptions can be classified as dominantly magmatic if the ratio of external water to magma is less than 0.2. Eruptions with water/melt ratios in the range of 0.2 to 1.0 are highly explosive and carry tephra in a hot vapor that contains dominantly superheated (dry) steam.

Sheridan, M. F.↗

NASA NTRS1985

On the Absence of Strike-slip Faults from the Planets and Satellites

Lunar grabens are bounded by two downward converging 60 deg dipping normal faults. These faults intersect below the surface at a major mechanical discontinuity in the shallow crust between the megaregolith (total ejecta built up by repeated cratering) and the underlying in situ fractured rock. The ymmetry and simplicity of lunar grabens demands that the bounding faults initiate at this mechanical discontinuity and propagate up. Wrinkle ridges are though to result from thrust faulting or compressional folding of mare basalts. Identification and analysis of a number of terrestrial analogs that are morphologically similar to lunar and martian examples indicates that wrinkle ridges results from thrust faulting. The location of wrinkle ridges above suggested subsurface basin structures indicates that the trend and location of many wrinkle ridges are inherited from these pre-existing basin structures. This implies that the thrust faults responsible for wrinkle ridges initiate at the ase of the basalt-basin floor contact. This contact almost certainly represents a mechanical discontinuity in the shallow lunar crust because mare basalts are undoubtedly stronger than the underlying fall-back ejecta of the basin floor.

Golombek, M. P.↗

NASA NTRS1985

The Deep Structure of Lunar Basins: Clues to the Understanding of Basin Formation and Modification

Basin excavation has played a major role in shaping the surface and subsurface of the Moon. Though photogeologic observations provide estimates for the present volumes of lunar impact basins and their ejecta deposits, there is not sufficient information to describe completely either the geometry of the basins at the time of impact or their modification with time. Determination of the structure of the crust and upper mantle beneath large basins can provide important insight into the thermal and mechanical processes associated with basin formation and modification as well as the differences in these processes as functions of basin age and size. Using observed gravity and topography together with the seismically determined crustal thickness of the central nearside, a model for the structure of the crust and upper mantle of the nearside of the Moon is presented. With this model the deep structure of the largest lunar basins are compared. The implications for the processes of basin formation and modification at different stages in lunar history are explored.

Bratt, S. R.↗

NASA NTRS1984

Sensitivity of Inferred Subphotospheric Velocity Field to Mode Selection, Analysis Technique and Noise

The horizontal velocity immediately below the photosphere was inferred from observations of high degree solar oscillations by an optimal averaging inversion technique. The sensitivity of the results to various details of both the inversion and the determination of the frequencies are investigated. The results are shown to be quite stable to the choice of most parameters, suggesting that this procedure produces reliable estimates of the subsurface velocity.

Hill, F.↗

NASA NTRS1984

Science with the Solar Optical Telescope (SOT)

Use of the Solar Optical Telescope (SOT) to study the energetics and dynamics of the solar atmosphere is described. Studies include the origin and evolution of the Sun's magnetic field, the structure of solar subsurface convection, the heating of the outer solar atmosphere, and sources of the solar wind in the lower lying regions of the outer atmosphere. To achieve the scientific goals of the SOT, it is necessary to observe features in the solar atmosphere on the scale of a typical photon mean-free-path in continuum radiation and also of the hydrodynamic or density scale-height. The 1.3 m telescope, of a Gregorian configuration, achieves close to 0.1 arcsec angular resolution on the Sun in visible and ultraviolet wavelengths.

Jordan, S. D.↗

NASA NTRS1985

Mars: Seasonally variable radar reflectivity

The 1971/1973 Mars data set acquired by the Goldstone Solar System Radar was analyzed. It was established that the seasonal variations in radar reflectivity thought to occur in only one locality on the planet (the Solis Lacus radar anomaly) occur, in fact, over the entire subequatorial belt observed by the Goldstone radar. Since liquid water appears to be the most likely cause of the reflectivity excursions, a permanent, year-round presence of subsurface water (frozen or thawed) in the Martian tropics can be inferred.

Roth, L. E.↗

NASA NTRS1985

Advanced rocket engine cryogenic turbopump bearing thermal model

A lumped node thermal model was developed representing the Space Shuttle Main Engine (SSME) liquid oxygen (LOX) turbopump turbine end bearings operating in a cryogenically cooled bearing tester. Bearing elements, shaft, carrier, housing, cryogen flow characteristics, friction heat, and fluid viscous energy are included in the model. Heat transfer characteristics for the regimes of forced convection boiling are modeled for liquid oxygen (LOX) and liquid nitrogen (LN2). Large temperature differences between the cryogenic fluid and baring contact surfaces require detailed nodal representation in these areas. Internal loads and friction heat are affected by temperature dependent operating clearances requiring iterations between bearing thermal and mechanical models. Analyses indicate a thermal-mechanical coupling resulting in reduced operating clearances, increased loading and heating which can contribute to premature bearing failure. Contact surfaces operate at temperatures above local saturation resulting in vapor rather than liquid in the contacts, precluding possible liquid film lubrication. Elevated temperatures can reduce lubrication, increase friction, and reduce surface hardness supporting a surface failure mode rather than subsurface fatigue.

Cody, J. C.↗

NASA NTRS1985

Role of Hydrogen and Structure on CMSX-2

The goal was to characterize and understand the detailed effect of hydrogen on the tensile and fatigue behavior of single crystals of CMSX-2. Specimens were solutionized, air cooled, and then aged in one of two ways. The resultant macro and microstructure included a pronounced dendritic structure with numerous low angle boundaries in the interdendritic region and on the average a high level of porosity with a large variation in size and distribution. Hydrogen permeability and diffusivity in this material was found to be very low at room temperature. Hydrogen concentration studies on thin samples yielded values significantly higher than found for similar charging conditions in nickel and stainless steels. The tensile mechanical properties were found to depend on hydrogen concentration. SEM observations of the brittle subsurface zone revealed a strong correlation between crack initiation sites and voids just beneath the surface. The hollow and solid samples were compared to better understand the influence of increased charged volume on the fatigue behavior.

Baker, C. L.↗

NASA NTRS1985

The structure of ion plated films in relation to coating properties

Ion plating is an ion assisted or glow discharge deposition technique, where ions or energetic atoms transfer energy, momentum and charge to the substrate and the growing film in a manner which can be controlled to favorably modify surface, subsurface chemistry, and microstructure. The glow discharge energizing effects from the initial nucleation stages to the final film growth are discussed. As a result, adherence, coherence, internal stresses, density and morphology of the coatings are significantly improved, over the conventional (nonion-assisted) techniques which in turn favorably affect the surface initiated failures caused by friction, wear, erosion, corrosion and fatigue. Ion plated films because of their graded coating/substrate interface, fine, uniform, densely packed film structure also induce a surface strengthening effect which improved the mechanical properties such as yield, tensile strength and fatigue life. Since a uniform, continuous film can be obtained at lower nominal film thickness, this effect is of great importance in solid film lubrication and in corrosion protection.

Spalvins, T.↗

NASA NTRS1985

Microwave hydrology: A trilogy

Microwave hydrology, as the term in construed in this trilogy, deals with the investigation of important hydrological features on the Earth's surface as they are remotely, and passively, sensed by orbiting microwave receivers. Microwave wavelengths penetrate clouds, foliage, ground cover, and soil, in varying degrees, and reveal the occurrence of standing liquid water on and beneath the surface. The manifestation of liquid water appearing on or near the surface is reported by a microwave receiver as a signal with a low flux level, or, equivalently, a cold temperature. Actually, the surface of the liquid water reflects the low flux level from the cosmic background into the input terminals of the receiver. This trilogy describes and shows by microwave flux images: the hydrological features that sustain Lake Baykal as an extraordinary freshwater resource; manifestations of subsurface water in Iran; and the major water features of the Congo Basin, a rain forest.

Stacey, J. M.↗

NASA NTRS1985

Geophysical interpretation of Venus gravity data

The investigation of the subsurface mass distribution of Venus through the analysis of the data from Pioneer Venus Orbiter (PVO) is presented. The Doppler tracking data was used to map the gravitational potential, which was compared to the topographic data from the PVO radar (ORAD). In order to obtain an unbiased comparison, the topography obtained from the PVO-ORAD was filtered to introduce distortions which are the same as those of our gravity models. The last major software package that was required in order to determine the spectral admittance Z (lambda) was used. This package solves the forward problem: given the topography and its density, and assuming no compensation, find the resulting spacecraft acceleration along a given nominal trajectory. The filtered topography is obtained by processing these accelerations in the same way (i.e., with the same geophysical inverter) as the Doppler-rate data that we use to estimate the gravity maps.

Reasenberg, R. D.↗

NASA NTRS1984

Satellite color observations of the phytoplankton distribution in the eastern Equatorial Pacific during the 1982-1983 El Nino

Images provided by the Coastal Zone Color Scanner (CZCS) onboard Nimbus-7 show the effect of the 1982-1983 El Nino upon the phytoplankton distribution around the Galapagos Islands, located on the equator. The CZCS scenes document a major redistribution of phytoplankton around the Galapagos Island during a period when sea-surface temperatures (SST) were anomalously high (28 to 29 C). The mixed layer was unusually thick for this region, and the winds and both the surface and subsurface flows changed directions. It is pointed out that the El Nino is characterized as one of the most spectacular examples of a large-amplitude, interannual response of the ocean to atmospheric forcing. The 1982-1983 El Nino is the best documented event of its kind to date, and details of its effects are discussed.

Feldman, G.↗

NASA NTRS1984

Interpretation of the lunar microwave brightness temperature spectrum - Feasibility of orbital heat flow mapping

The feasibility of an orbital mapping of heat flow by means of microwave radiometers is examined on the basis of a detailed model of the lunar regolith. The results obtained are discussed in terms of contributions of physical properties and regolith structure to the spectral signature of lunation-averaged brightness temperatures. Even for regions for which remote heat flow detection is not feasible, detailed interpretations of remote measurements in terms of physical properties and regolith structure could be made by means of the model presented. Surface and subsurface scattering effects are considered in evaluating possible wavelength dependencies of the microwave emissivity.

Keihm, S. J.↗

NASA NTRS1984

Planetary observations at a wavelength of 1.32 mm

Observations at a wavelength of 1.32 mm have been made of the Jovian planets, Ceres, the satellites Callisto and Ganymede, and the HII region DR 21. The observed brightness temperatures are presented. Those of the Jovian planets agree with the values expected from model atmosphere calculations, except that of Jupiter, which is lower than expected. Ceres and the satellites do not have atmospheres so their emission arised in their subsurface layers. The observed brightness temperatures are intermediate between those measured at infrared and centimeter wavelengths.

Ulich, B. L.↗

NASA NTRS1985

The rise and fall of sunspot group 18962 - A case of magnetic submergence

Normal sunspot groups emerge from below the surface as a big arch; the footpoints form a dipole that moves apart and the fields eventually diffuse and disappear. BBSO 18962 was a small dipole with elements which, after spreading apart in the first day of existence, drew back together and disappeared below the surface. It is proposed that the flux loop was pulled back down by magnetic tension and submerged. The circumstances suggest that this behavior may not be uncommon. It implies that some dipoles do not decouple from subsurface fields.

Zirin, H.↗

NASA NTRS1984

Geologic interpretation of Seasat SAR imagery near the Rio Lacantum, Mexico

A mosaic of the Seasat Synthetic Aperture Radar (SAR) optically processed images over Central America is presented. A SAR image of the Rio Lacantum area (southeastern Mexico) has been digitally processed and its interpretation is presented. The region is characterized by low relief and a dense vegetation canopy. Surface is believed to be indicative of subsurface structural features. The Seasat-SAR system had a steep imaging geometry (incidence angle 23 + or - 3 deg off-nadir) which is favorable for detection of subtle topographic variations. Subtle textural features in the image corresponding to surface topography were enhanced by image processing techniques. A structural and lithologic interpretation of the processed images is presented. Lineaments oriented NE-SW dominate and intersect broad folds trending NW-SE. Distinctive karst topography characterizes one high relief area

Rebillard, PH.↗

NASA NTRS1985

Ceramic wear in indentation and sliding contact

The various wear mechanisms involved with single-crystal ceramic materials in indentation and in sliding contacts. Experiments simulating interfacial events have been conducted with hemispherical, conical and pyramidal indenters (riders). With spherical riders, under either abrasive or adhesive conditions, two types of fracture pits have been observed. First, spherical-shaped fracture pits and wear particles are found as a result of either indenting or sliding. These are shown to be due to a spherical-shaped fracture along the circular or spherical stress trajectories. Second, polyhedral fracture pits and debris, produced by anisotropic fracture, and also found both during indenting and sliding. These are primarily controlled by surface and subsurface cracking along cleavage planes. Several quantitative results have also been obtained from this work. For example, using a pyramidal diamond, crack length of Mn-Zn ferrite in the indentation process grows linearly with increasing normal load. Moreover, the critical load to fracture both in indentation and sliding is essentially isotropic and is found to be directly proportional to the indenter radius.

Miyoshi, K.↗