SEARCH · Engineering Papers

Results for “Strain calculation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Isothermal life prediction of composite lamina using a damage mechanics approach

A method for predicting isothermal plastic fatigue life of a composite lamina is presented in which both fibers and matrix are isotropic materials. In general, the fatigue resistances of the matrix, fibers, and interfacial material must be known in order to predict composite fatigue life. Composite fatigue life is predicted using only the matrix fatigue resistance due to inelasticity micromechanisms. The effect of the fiber orientation on loading direction is accounted for while predicting composite life. The application is currently limited to isothermal cases where the internal thermal stresses that might arise from thermal strain mismatch between fibers and matrix are negligible. The theory is formulated to predict the fatigue life of a composite lamina under either load or strain control. It is applied currently to predict the life of tungsten-copper composite lamina at 260 C under tension-tension load control. The calculated life of the lamina is in good agreement with available composite low cycle fatigue data.

Abuelfoutouh, Nader M.↗

NASA NTRS1989

Isothermal life prediction of composite lamina using a damage mechanics approach

Abuelfoutouh, Nader Mohamed↗

NASA NTRS1991

Preliminary investigation of acousto-ultrasonic evaluation of metal-matrix composite specimens

Acoustoultrasonic (AU) measurements were performed on a series of (0)8, (90)8, (+/-30)2s, (+/-60)2s, (0/90)2s, and (90/0)2s tensile specimens composed of eight laminated layers of continuous, SiC-fiber-reinforced Ti-15-3 matrix. The frequency spectrum was dominated by frequencies of longitudinal wave resonance through the thickness of the specimen at the sending transducer; signal propagation from the sender to the receiver was by shear waves. The magnitude of the frequency spectrum of the AU signal was used for calculating a stress-wave factor (SWF) based upon integrating the spectral distribution function. The SWF was sensitive to fiber-matrix debonding caused by mechanical strain and also to unconstrained thermal cycling. Damage in this metal-matrix composite structure due to tensile loading or thermal cycling was detected by this change in the magnitude of the frequency spectrum.

Kautz, Harold E.↗

NASA NTRSDate not supplied

Congruence of Clusters Defined By Whole Genome Sequencing and MALDI-TOF for Bacteria Isolated From Cleanrooms

Introduction: Oligotrophic conditions can render cleanrooms inhospitable to microbes. Despite these constraints, fungi and bacteria are frequently isolated from surfaces in astromaterials cleanrooms at the Johnson Space Center. Bacillus species are of particular concern because endospores belonging to this genus are resilient and can affect astromaterials. Current monitoring programs rely on 16S rRNA sequencing and the VITEK2 Compact system. These methods have limited power to resolve Bacillus species. Matrix-assisted laser desorption - time of flight mass spectrometry (MALDI-TOF MS), provides a rapid, low cost, method of identifying bacterial isolates and has a higher resolution than 16S rRNA sequencing, particularly for Bacillus species; however, few studies have compared this method to the industry gold standard, whole genome sequencing (WGS). Methods: Based on 16S rRNA classification, we selected 14 isolates for analysis with MALDI-TOF and WGS. Mass spectra were generated with MALDI-TOF MS and processed with custom scripts to identify clusters of closely related isolates and calculate a matrix of pairwise cosine similarity scores. Hybrid Illumina and Nanopore sequencing were used to generate draft genomes. Pairwise similarity scores were calculated from these genomes based on the average amino acid identity (AAI) predicted from single copy core genes. Congruence of clustering between these methods, was assessed by calculating adjusted Rand and Wallace coefficients. Results: Clusters of species generated from MALDI-TOF MS showed good agreement of phylotypes generated with WGS. Pairs of strains that were > 94% similar to each other in terms of predicted amino acid sequences consistently showed cosine similarities of mass spectra > 0.65 and, of the 9 clusters identified with WGS, 8 were identical with MALDI-TOF. This corresponds to an adjusted Rand index of 0.95 and a 95% confidence interval of 0.80 – 1.00 for adjusted Wallace coefficients. The only discordance was for a pair of isolates that were classified as Paenibacillus species. This pair showed relatively high similarity (0.84) in terms of MALDI-TOF MS but only 85% similarity in terms of AAI. Conclusion: This study shows that MALDI-TOF and WGS exhibit a similar ability to delineate Bacillus species isolated from cleanrooms and taxonomic units described by these two methods are consistent with one another. Since MALDI-TOF MS is low in cost and high in throughput, this approach appears to be an ideal option for routine microbial monitoring and identifying Bacillus species.

Farnaz Mazhari↗

NASA NTRS2016

A New Load Residual Threshold Definition for the Evaluation of Wind Tunnel Strain-Gage Balance Data

A new definition of a threshold for the detection of load residual outliers of wind tunnel strain-gage balance data was developed. The new threshold is defined as the product between the inverse of the absolute value of the primary gage sensitivity and an empirical limit of the electrical outputs of a strain{gage. The empirical limit of the outputs is either 2.5 microV/V for balance calibration or check load residuals. A reduced limit of 0.5 microV/V is recommended for the evaluation of differences between repeat load points because, by design, the calculation of these differences removes errors in the residuals that are associated with the regression analysis of the data itself. The definition of the new threshold and different methods for the determination of the primary gage sensitivity are discussed. In addition, calibration data of a six-component force balance and a five-component semi-span balance are used to illustrate the application of the proposed new threshold definition to different types of strain{gage balances. During the discussion of the force balance example it is also explained how the estimated maximum expected output of a balance gage can be used to better understand results of the application of the new threshold definition.

load residuals↗

DOE OSTI2024

Zero-strain high entropy spinel oxide (FeNiCuCrMn) 3 O 4 @rGO as high-performance anode for sodium ion battery

High entropy spinel oxides (HEOs), as a new type of anode material with at least five transition metal elements and high theoretical specific capacity, have enormous promise in sodium ion batteries (SIBs). However, the influence of different transition metal elements on the structure and electrochemical performances of HEOs is not clear. Here, in this study, the addition of Mn to HEO can increase the surface oxygen vacancy (O v ) concentration, shorten the band gap, and enhance the electrochemical performance of (FeNiCuCrMn) 3 O 4 @rGO. XPS results show (FeNiCuCrMn)3O4@rGO has the highest surface O v concentration. Ab initio calculations demonstrate that the indirect band gap of (FeNiCuCrMn)3O4@rGO is 0.068 eV. In situ X-ray diffraction and synchrotron X-ray absorption spectroscopy reveal that (FeNiCuCrMn) 3 O 4 @rGO exhibits a zero-strain characteristic with an inconsequential unit cell volume change of 0.2 %. Specifically, (FeNiCuCrMn) 3 O 4 @rGO as anode materials for SIBs show good cyclic stability (with a capacity retention of 84 % at 500 mA g −1 after 3000 cycles). Overall, this work provides a new direction for optimizing transition metal elements in HEOs.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Composition dependence of atomic order in strain-relaxed, metastable GeSn alloys

Extended x-ray absorption fine structure (EXAFS) measurements of single-crystal Ge/GeSn radial heterostructure nanowires are used to examine the effects of composition on both short-range order (SRO) and longer-range disorder in GeSn alloys. GeSn has prompted significant interest because it can achieve a direct band gap for sufficient Sn concentrations beyond the equilibrium solid solubility limit in an all-group IV system. Short-range order in this material is particularly interesting as it has been predicted to affect the band gap independent of average composition or strain effects. By independently controlling the Sn composition and GeSn thickness during chemical vapor deposition of misfitting GeSn shells around ultrathin, elastically compliant, Ge core nanowires, the elastic misfit strain in the GeSn is minimized for Sn compositions over the studied range ≈Ge 0.96 Sn 0.04 to Ge 0.88 Sn 0.12 . The degree of SRO was found to decrease with increasing Sn composition. Additionally, damping of the EXAFS signal was observed as the Sn content increased, particularly for increasingly distant atomic shells about the absorbing atom, even for scattering paths not involving Sn atoms. This result is quantified as an increase in the mean-squared relative displacement parameters of the shells. These measurements reveal the accommodation of local strain due to the presence of the highly size-mismatched Sn atoms in the Ge diamond cubic lattice (≈14%), which may have effects on the band structure of the material in addition to the influence of short-range atomic order. Comparison among the nanowire samples allows for calculation of the topological rigidity parameter, a ∗∗ , for the first-neighbor bond lengths. Furthermore, these exhibit chemically distinct values for Ge-Ge, Ge-Sn, and Sn-Sn, and they are consistent with the value a ∗∗ = 0.75 ± 0.07 confirming the general applicability of the model to alloys with both large amounts of natural misfit strain and the potential for short-range order.

Crystal structure Semiconductors Transmission elec↗

DOE OSTI2023

Eulerian finite element implementations of a dislocation density-based continuum model

In Eulerian finite element simulations, the mesh moves relative to the material. After every change of position between the mesh and the material, the state variables are interpolated to the new mesh position, which is referred to as advection. Large strain crystal plasticity models are based on the multiplicative decomposition of the total deformation gradient. Further, the stress is evaluated as a function of the thermoelastic strain, temperature, and other state variables. Advection of tensor quantities, such as the strain, is coupled with possibly significant advection errors. In an effort to reduce the advection errors, we develop two rate forms of an established dislocation density-based continuum model. To that end, we replace the multiplicative decomposition of the deformation gradient with the additive decomposition of the velocity gradient, and define the stress rate instead of the total stress. The Eulerian implementation is compared with Lagrangian calculations, and two numerical examples with severe deformation levels are presented.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Site-Controlled Quantum Emitters in Monolayer MoSe 2

Atomically thin semiconductors provide a highly attractive platform for quantum emitters (QEs): They can be combined with arbitrary substrates, can be spatially aligned with photonic structures, and can be electrically driven. All QEs reported to date in these materials have, however, relied on nominally spin-forbidden transitions, with radiative rates falling substantially below those of other solid-state QE systems. In this work, we employ strain confinement in monolayer MoSe 2 to produce engineered QEs, as confirmed in photon antibunching measurements. We discuss spin-allowed versus spin-forbidden transitions based on magneto- and time-resolved photoluminescence measurements. We calculate a radiative rate for spin-allowed quantum emission greater than 1 ns –1 , which exceeds reported radiative rates of WSe 2 QEs by 2 orders of magnitude.

2D materials↗

NASA NTRS1993

Analysis of matrix cracking and local delamination in (0/theta/-theta)s graphite epoxy laminates under tensile load

Three-dimensional element analyses of (0/theta/-theta)s graphite epoxy laminates, where theta = 15, 20, 25, 30, and 45 deg, subjected to axial tensile load, were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and the free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized Mode I component near the free edge, within one-ply distance from the matrix crack. To examine the stress state causing the matrix cracking, the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increased through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface.

Salpekar, S. A.↗

DOE OSTI2025

Strained-Induced Morphological Reconstruction of RuO 2 (110) Thin-Film Electrocatalysts

Strain is a widely used strategy for electrocatalyst engineering. Overstraining, however, can lead to unintentional materials transformation. We investigate the impact of strain on the surface morphology of a rutile RuO 2 (110) film grown on a symmetry-matching rutile TiO 2 (110) substrate. When the film thickness exceeds 9 nm, the RuO 2 surface relaxes by forming step edges that expose the {011} plane. Density functional theory (DFT) calculation shows that the (011) facet is among the lower energy surfaces of rutile RuO 2 , suggesting that this formation incurs minimal energetic penalties. In situ atomic force microscopy (AFM) shows that the film maintains the (110) structure of the terrace during electrochemistry. Inductively coupled plasma–mass spectrometry (ICP-MS) further reveals the insensitivity of the Ru dissolution to strain. Here, our findings show a strain-relieving pathway via surface reconstruction in RuO 2 (110) and provide an example of a strain-relieving mechanism that does not affect dissolution.

Evolution reactions↗

NASA NTRS1991

Analysis of matrix cracking and local delamination in (0/theta/-theta)sub s graphite epoxy laminates under tension load

Several 3D finite element analyses of (0/theta/-theta)sub s graphite epoxy laminates, where theta=15, 20, 25, 30, and 45 deg, subjected to axial tension load were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized mode I component near the free edge, within one ply distance from the matrix crack. In order to examine the stress state causing the matrix cracking the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increases through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface. Crack profiles on the laminate edge in the -theta ply were constructed from the principal stress directions. The cracks were found to be more curved for layups with smaller theta angles, which is consistent with experimental observations in the literature.

Salpekar, S. A.↗

NASA NTRS1991

Analysis of matrix cracking and local delamination in (O/theta/-theta)sub s graphite epoxy laminates under tension load

Several 3D finite element analyses of (O/theta/-theta)sub s graphite epoxy laminates, where theta = 15, 20, 25, 30, and 45 deg, subjected to axial tension load were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized mode I component near the free edge, within one ply distance from the matrix crack. In order to examine the stress state causing the matrix cracking the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increases through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface. Crack profiles on the laminate edge in the -theta ply were constructed from the principal stress directions. The cracks were found to be more curved for layups with smaller theta angles, which is consistent with experimental observations in the literature.

Salpekar, S. A.↗

DOE OSTI2020

Eigenfrequency constrained topology optimization of finite strain hyperelastic structures

This paper incorporates hyperelastic materials, nonlinear kinematics, and preloads in eigenfrequency constrained density–based topology optimization. The formulation allows for initial finite deformations and subsequent small harmonic oscillations. The optimization problem is solved by the method of moving asymptotes, and the gradients are calculated using the adjoint method. Both simple and degenerate eigenfrequencies are considered in the sensitivity analysis. A well-posed topology optimization problem is formulated by filtering the volume fraction field. Numerical issues associated with excessive distortion and spurious eigenmodes in void regions are reduced by removing low volume fraction elements. The optimization objective is to maximize stiffness subject to a lower bound on the fundamental eigenfrequency. Numerical examples show that the eigenfrequencies drastically change with the load magnitude, and that the optimization is able to produce designs with the desired fundamental eigenfrequency.

42 ENGINEERING↗

DOE OSTI2025

Intrinsic property of defective β-Ga 2 O 3 to self-heal under ionizing irradiation

Damage evolution and phase stability in defective β-Ga 2 O 3 and an irradiation-converted γ-Ga 2 O 3 layer have been studied under ionizing irradiation at 300 K. By exploring athermal nonequilibrium processes in β-Ga 2 O 3 , we succeed in identifying a self-healing mechanism that enables recovery pre-existing damage, characterized by a recovery cross-section of ~0.17 nm 2 . Remarkably, this study further demonstrates that the crystallinity of the irradiation-converted γ-Ga 2 O 3 layer improves under ionizing irradiation. More importantly, X-ray diffraction analysis reveals that the highly-strained 𝛾 -phase transforms into a highly-crystalline structure without film disintegration, contrasting to that reported for isochronal annealing at 1000 K. The inelastic thermal spike calculations provide insights into the important effects of energy transfer to electrons in reordering the local atomic arrangement of both defective β- Ga 2 O 3 and 𝛾-Ga 2 O 3 . This behavior suggests a pathway for low-temperature crystallization, offering a promising strategy for fabricating ultrahigh-speed non-volatile memory devices.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Dynamic compression and spallation behavior of NbTaTiVZr high-entropy alloy

High-entropy alloys are a new class of materials with promising properties for aerospace and defense applications. The unique behavior of these materials is driven by the complex interactions between dissimilar atoms in a crystal and requires combined theoretical and experimental efforts to unlock their full potential. Here, we evaluate the relationship between the microstructure and the dynamic response of the equiatomic NbTaTiVZr alloy. Specifically, the shock Hugoniot, or equation of state, was measured up to a particle velocity of 0.5 mm μs −1 using gas gun plate impacts. Shock wave profile and incipient spallation experiments were used to characterize wave propagation and damage formation with post-mortem recovery experiments. Molecular dynamics simulations confirm the experimental findings and extend them up to 2.1 mm μs −1 particle velocity. Computational thermodynamic calculation of phase diagram simulations explain details of the material microstructure, which explains the measured strength and experimental damage patterns. Overall, this work provides detailed high-strain-rate characterization of a refractory high-entropy alloy, and more importantly, a framework and demonstration of the utility and necessity of a combined theoretical and experimental approach, outlining the importance of considering processing and manufacturing conditions when evaluating the performance of new materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Experimental and theoretical investigation of FeCrVAl and related compounds

Abstract We have carried out a combined theoretical and experimental investigation of FeCrVAl, and the effect of Mn and Co doping on its structural, magnetic, and electronic band properties. Our first principles calculations indicate that FeCrVAl, FeCr 0.5 Mn 0.5 VAl, and FeCr 0.5 Co 0.5 VAl exhibit nearly perfect spin polarization, which may be further enhanced by mechanical strain. At the same time, FeCrV 0.5 Mn 0.5 Al and FeCrV 0.5 Co 0.5 Al exhibit a relatively small value of spin polarization, making them less attractive for practical applications. Using arc melting and high vacuum annealing, we synthesized three compounds FeCrVAl, FeCr 0.5 Mn 0.5 VAl, and FeCr 0.5 Co 0.5 VAl, which are predicted to exhibit high spin polarization. The room temperature x-ray diffraction patterns of all samples are fitted with full B2 type disorder with a small amount of FeO 2 secondary phase. All samples show very small saturation magnetizations at room temperature. The thermomagnetic curves M(T) of FeCrVAl and FeCr 0.5 Co 0.5 VAl are similar to that of a paramagnetic material, whereas that of FeCr 0.5 Mn 0.5 VAl indicates ferrimagnetic behavior with the Curie temperature of 135 K. Our findings may be of interest for researchers working on Heusler compounds for spin-based electronic applications.

Physics↗

DOE OSTI2024

Rapid Design of Cost-Effective Refractory High Entropy Alloys Strengthened by Precipitation

Funded by the ARPA-E ULTIMATE program, this project aims to develop cost-effective refractory high entropy alloys (RHEAs) for gas turbine blades applications at 1300 degree Celsius and above. The alloy design focuses on carbides precipitation strengthening in a strong and ductile solid solution BCC matrix. The goal is to achieve balanced mechanical properties including room temperature ductility & fracture toughness and high temperature strength and creep resistance, while maintaining comparable oxidation resistance and densities to Ni-base superalloys. To accelerate alloy design, multiscale modeling including CALPHAD and first-principles density functional theory (DFT) calculations and machine learning are performed. Specifically, high throughput phase diagram calculations and screening are carried out using CALPHAD; DFT calculations are performed to predict intrinsic ductility, grain boundary strengthening potential, coefficient of thermal expansion (CTE) and temperature-dependent elastic constants. Temperature dependent yield stress, creep strain and CTE are also predicted using machine learning. Down-selected alloys are synthesized in small buttons of about 250g using arc melting for rapid evaluation on microstructure and mechanical properties before employing plasma arc melting and additive manufacturing for producing large ingots. Preliminary computational and experimental results of this project will be presented and future direction in RHEA development will be discussed.

high temperature materials↗