SEARCH · Engineering Papers

Results for “Source and propagation modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

A Warm Garage for a Lunar Rover

Approach: One approach to heating a rover during the lunar night is the so-called thermal wadis concept [1]. This involves heating the regolith with solar concentrators and placing the rover on the heated surface for the night. Since the regolith is heated by a relatively weak heat flux, a high thermal conductivity is required for heating a sufficiently large mass of regolith. However, lunar regolith has a low thermal conductivity. Therefore, the concept involves increasing the conductivity by sintering the regolith, which requires a significant energy input and complex procedures. Here we propose an alternative approach where the low thermal conductivity of regolith is an advantage. Specifically, we propose to use a highly exothermic combustible mixture for heat generation. The mixture pellets are placed in the surface layer of regolith and ignited. The combustion forms condensed products and releases heat, which then slowly spreads to the surrounding regolith. Heat can also be transferred, for example, by heat pipes, into radiant heating surfaces installed on the ground. A greenhouse that transmits sunlight during the day and decreases the radiative heat losses during the night can also be installed. Selection of the Heat-generating Mixture: The reactive mixture should have a high specific energy and generate only condensed products since gases could disturb the regolith layer, carry enthalpy out of the system, and lead to an explosion. There are mixtures, (sometimes called pyrolants) that possess very high specific energies. One example is magnesium-Teflon-Viton mixtures used in flares. However, they produce gases and may cause explosions. Other mixtures that include magnesium cannot be used either because of the high vapor pressure of Mg at temperatures well below the combustion temperature. Recently, mixtures that involve lithium peroxide (Li2O2) have been proposedfor using in space power systems [2]. However, they produce lithium oxide (Li2O), which boils at 2800 K at 1 atm and hence at a lower temperature in vacuum. Fortunately, there exist many mixtures that release a lot of heat and form only condensed products during the combustion. Many such mixtures have been used for self-propagating high-temperature synthesis (SHS) of various materials [3, 4]. For the application discussed here, t itanium/boron (1:2 mole ratio) mixture appears to be particularly promising. The specific energy is 4.0 MJ/kg (1.1 kWh/kg), the adiabatic flame temperature is about 3200 K, and the reaction forms solid titanium diboride (TiB2, melting point: 3500 K). The mixture can be ignited easily with a heated tungsten wire, and it has been used widely as a booster to ignite the main mixture in the SHS process.Estimates: Assuming that specific heat of regolith is 500 J/(kg∙K) [5] and all generated heat is transferred to regolith, 12.5 kg of the Ti/B mixture would increase the temperature of 1000 kg of regolith by 100 K. To evaluate the rate of heat transfer in the regolith, a spherical model was analyzed where the heat released by a 12.5 kg Ti/B core propagates by thermal conduction through a 1000 kg regolith shell with no heat loss from its outer surface. At a bulk density of 1500 kg/m3 [5], the radius of the shell was 54 cm, while the radius of the core was about 11 cm. The calculations were conducted using Thermal Desktop SINDA/FLUINT (Cullimore and Ring Technologies) software at two constant values of bulk thermal conductivityk of the regolith: 0.001 and 0.01 W/(m∙K). The results show that after 14.5 days the core lost 31% of the released heat at the lower k and 77% at the higher k. At a distance of 20 cm from the core surface, the temperature of the regolith increased by only 1 K at the lower k and by 132 K at the higher k. In reality, the regolith near the heat source will be melted, so its thermal conductivity will increase significantly. Nevertheless, the conducted estimates indicate that combustion-based heat generators, placed directly in the regolith, could provide heat during a rather long period such as the lunar night.Conclusion: Heat generators based on gasless combustion of highly energetic reactive mixtures could be installed directly in the surface layer of lunar regolith. Because of the low thermal conductivity of the regolith, such generators would keep thermal energy for days and gradually supply heat to a rover/lander.Acknowledgment: The material presented in this work is based upon the work supported by National Aeronautics and Space Administration (NASA) under Grant #80NSSC20K0293.References: [1] Balasubramaniam R. et al. (2011) J. Thermophys. Heat Trans., 25,130−139. [2] Blair R.G. and Vasu S.S. (2022) Conf. Advanced Power Systems for Deep Space Exploration. [3] Varma A. et al. (1998) Adv. Chem. Eng., 24,79−226. [4] Levashov E.A. et al. (2017) Int. Mater. Rev., 62,203−239. [5] Wood-Robinson R. et al. (2019) J. Geophys. Res. Planets, 124, 1989−2011.

lunar↗

NASA NTRS1992

Supersonic acoustic source mechanisms for free jets of various geometries

The aeroacoustic performance of several generic nozzle geometries was tested to evaluate the potential benefits of using non-round jet exit geometries to reduce noise from combat military aircraft. Both the aerodynamics and far field acoustics of several M(sub d) = 1.5 and 2.0 round, elliptic, and rectangular nozzles, including an augmented deflector exhaust nozzle (ADEN), were studied to assess noise emission. The nozzles were operated to jet total temperatures, T(sub 0) = 1160 degree R, and the data scaled to constant thrust. The data were propagated to 1500 ft. and corrected to perceived noise level. The aerodynamic results of the study show that the non-round nozzle geometries mix much faster with the surrounding medium than does an equivalent round nozzle plume. Both the ADEN and elliptic nozzles provide significant reduction of noise, 6 to 7 PNdB, along the major axis direction with little expected impact on nozzle performance. Shock noise processes are eliminated for elliptic nozzles, but are still significant with rectangular nozzles. Comparison of measurements to theoretical predictions of noise using the quasi-linear instability wave model demonstrates good qualitative agreement.

Seiner, John M.↗

NASA NTRSDate not supplied

Development of Acoustic Mufflers for Cabin Noise Reduction in Orion Spacecraft

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical to ensure adequate speech intelligibility, to avoid fatigue, and prevent any possibility of temporary and permanent hearing loss to the crew. The primary source of cabin noise for the on-orbit phase of the mission is from the Environmental Control and Life Support System (ECLSS) which recycles and conditions breathing air and maintains cabin pressurization through its duct network and components. Unfortunately, as a side effect, noise from the ECLSS fans propagates through theses ducts and emanate into the cabin habitable volume via the ECLSS inlet and outlets. To mitigate excessive duct-borne noise, two ECLSS mufflers have been designed to provide significant acoustic transmission loss (TL) so that the cabin noise requirements can be met. Each muffler is meant to be installed in the ducting of the ECLSS air inlet and outlet sides, respectively. Packaging constraints and tight volume requirements necessitated the mufflers to be of complex geometry and compatible with the bends of the ECLSS duct layout. To design and characterize the acoustic performance of the inlet and outlet mufflers, computational acoustic models were developed using the Finite Element Method (FEM) with 𝑤𝑎𝑣𝑒଺ vibroacoustic software. Characterization of the acoustic material and perforations in the mufflers were addressed with poroelastic theory. Once the mufflers were designed on paper and its TL predicted, prototypes of these mufflers were created using additive manufacturing. The muffler prototypes were subsequently tested for acoustic TL in the laboratory with various con-figurations of acoustic materials. Comparing the analytical predictions to the test performance yielded excellent correlation for acoustic TL and demonstrated significant broadband noise attenuation. The ECLSS mufflers are currently scheduled to be installed on the Artemis II Crew Module (CM) of the Orion spacecraft and will provide significant cabin comfort to crew during the mission.

Indranil Dandaroy↗

DOE OSTI2025

A Continuous Galactic Line Source of Axions: The Remarkable Case of 23 Na

Here, we argue that $^{23}$Na is a potentially significant source of galactic axions. For temperatures $\gtrsim 7 \times 10^8$K -- characteristic of carbon burning in the massive progenitors of supernovae and ONeMg white dwarfs -- the 440 keV first excited state of $^{23}$Na is thermally populated, with its repeated decays pumping stellar energy into escaping axions. Odd-A nuclear abundances are typically very low in high-temperature stellar environments (or absent entirely due to burn-up). $^{23}$Na is an exception: $\approx 0.1 M_\odot$ of the isotope is synthesized during carbon burning then maintained at $\approx 10^9$K for times ranging up to $6 \times 10^4$y. Using MESA simulations, a galactic model, and sampling over progenitor masses, locations, and evolutionary stages, we find a continuous flux at earth of $\langle ϕ_a \rangle \approx 22$/cm$^2$s for $g^\mathrm{eff}_{aNN} = 10^{-9}$. Some fraction of these axions convert to photons as they propagate through the galactic magnetic field, producing a distinctive 440 keV line $γ$ ray detectable by all-sky detectors like the Compton Spectrometer and Imager (COSI). Assuming a 1$μ$G galactic magnetic field and a sufficiently light axion mass, we find that COSI will be able to probe $| g_{aNN}^\mathrm{eff} g_{a γγ} | \gtrsim1.8 \times 10^{-22}$ GeV$^{-1}$ at $3σ$ after two years of surveying.

Dark matter↗

NASA NTRS1993

Mars dust-driven tides and their impact on the thermosphere

It has been known since the early Mariner 6, 7, and 9 missions that dust loading of the lower atmosphere and the subsequent aerosol heating during dusty periods impacts the martian middle and upper atmospheres. A quantitative measure of this lower atmosphere forcing was obtained by the Viking 1 and 2 landers, from which observed amplitudes of semidiurnal surface-pressure oscillations were correlated with normal-incidence dust optical depths. It appears that the dominant semidiurnal mode is a good indicator of global dust content or mean dust optical depth, especially during dust storm events. A classical tidal model that reproduces the surface pressure oscillations measured by these Viking landers in 1977 was used to calculate tidal amplitudes and phases up to approximately 43 km. These tidal characteristics were calculated for various dust optical depth conditions ranging from typical dusty periods to global dust storm times. Reasonable extrapolations can be made to higher altitudes if one assumes that the vertically propagating tidal modes continue to grow without dissipation or breaking. It is very likely that gravity waves also play an important role in the structure and dynamics of the middle atmosphere of Mars, since the large topographical relief should produce vigorous gravity wave fluxes. Semidiurnal tidal modes, significantly enhanced by lower atmosphere dust-induced heating, may indeed propagate to the Mars thermosphere (approximately less than 100 km) before breaking and generating turbulence. The preferential enhancement of the semidiurnal tides during dust storm onset is primarily due to the elevation of the tidal heating source in a very dusty atmosphere. The (2,2) semidiurnal tidal tidal mode was shown to have the largest variation with dust optical depth, as measured by Viking lander instruments. Also, the (2,2) mode has the largest vertical wavelength of all the semidiurnal tidal modes, and thus is most likely to penetrate into the thermosphere before breaking and to modify the largely in situ solar-driven behavior otherwise expected. The tides may also be partially responsible for determining the height of the martian homopause (approximately 125 km).

Bougher, Stephen W.↗

NASA NTRS2004

Cone Model for Halo CMEs: Application to Space Weather Forecasting

In this study, we present an innovative analytical method to determine the angular width and propagation orientation of halo Coronal Mass Ejections (CMEs). The relation of CME actual speed with apparent speed and its components measured at different position angle has been investigated. The present work is based on the cone model proposed by Zhao et al. We have improved this model by: (1) eliminating the ambiguity via a new analytical approach, (2) using direct measurements of projection onto the plane of the sky (POS), and (3) determining the actual radial speeds from projection speeds at different position angles to clarify the uncertainty of projection speeds in previous empirical models. Our analytical approach allows us to use coronagraph data to determine accurately the geometrical features of POS projections, such as major axis, minor axis, and the displacement of the center of its projection, and to determine the angular width and orientation of a given halo CME. Our approach allows for the first time the determination of the actual CME speed, width, and source location by using coronagraph data quantitatively and consistently. The method greatly enhances the accuracy of the derived geometrical and kinematical properties of halo CMEs, and can be used to optimize Space Weather forecasts. The applied model predications are in good agreement with observations.

Xie, Hong↗

DOE OSTI2023

Toward Global Regional Seismic Moment Tensor Inversion with Three-Dimensional Earth Models for Nuclear Explosion Monitoring with Sparse Networks: Demonstration of Reciprocity for Strain Greens Tensor Database Simulation with Salvus

Seismic source characterization is an essential function of global nuclear explosion monitoring (NEM). While large events (roughly with moment magnitude, M w , greater than 5.0) can often be easily detected, located and identified with high signal-to-noise ratios at teleseismic distances (> 20°), trends in NEM research require confident source characterization at much lower magnitudes (say down to 3.0) and exploitation of sparse observations (from only a few stations) at regional distance (< 20°). Regional distance waveform inversion to characterize sources is now widely used and effective (e.g. Ford et al., 2009; Alvizuri and Tape, 2018; Alvizuri et al., 2018; Chiang et al., 2018; Ford et al., 2022). These methods obtain the magnitude, depth and seismic moment tensor, which represents the forces that excited the observed seismic waves (slip on an earthquake fault, explosion, collapse or a combination of various forces). Common to many problems in seismology, the isolation of the source 2 properties requires removal of path propagation effects that waves experience while traveling through the three-dimensional (3D) Earth (the structure exists due to different rock types, material properties, temperature and tectonic processes).

58 GEOSCIENCES↗

DOE OSTI2025

The gallium solar neutrino capture cross section revisited

Solar neutrino flux constraints from the legacy GALLEX/GNO and SAGE experiments continue to influence contemporary global analyses of neutrino properties. The constraints depend on the neutrino absorption cross sections for various solar sources. Following recent work updating the 51 Cr and 37 Ar neutrino source cross sections, we reevaluate the 71 Ga solar neutrino cross sections, focusing on contributions from transitions to 71 Ge excited states, but also revising the ground-state transition to take into account new 71 Ge electron-capture lifetime measurements and various theory corrections. The excited-state contributions have been traditionally taken from forward-angle (𝑝, 𝑛) cross sections. Here we correct this procedure for the ≈ 10%–20% tensor operator contribution that alters the relationship between Gamow-Teller and (𝑝, 𝑛) transition strengths. Using state-of-the-art nuclear shell-model calculations to evaluate this correction, we find that it lowers the 8 B and hep neutrino cross sections. However, the addition of other corrections, including contributions from near-threshold continuum states that radiatively decay, leads to an overall increase in the 8 B and hep cross sections of ≈ 10% relative to the values recommended by Bahcall. Uncertainties are propagated using Monte Carlo simulations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Colliding Pulse Mode Locking and Nonequilibrium Carrier Dynamics within Vertical External-Cavity Surface-Emitting Lasers

The complex nonlinear dynamics of colliding counterpropagating ultrashort laser pulses circulating in a vertical external-cavity surface-emitting ring laser cavity are captured by a first-principles quantum-mechanical microscopic model coupled to an intracavity beam propagator. Furthermore, our numerical simulations establish that overall mode locking stability is sensitive to relative phases and delays of the pulses impinging on the semiconductor saturable absorber mirror. Delay offsets of the counterpropagating pulses lead to asymmetric carrier recovery and instability, often leading in turn to single unidirectional circulating pulses. Although computationally challenging, we also include transverse effects and show that the influence of interference patterns from spatial gratings written by the counterpropagating pulses is significant in stabilizing the modelocked pulses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2006

Receiver Would Control Phasing of a Phased-Array Antenna

In a proposed digital signal-processing technique, a radio receiver would control the phasing of a phased-array antenna to aim the peaks of the antenna radiation pattern toward desired signal sources while aiming the nulls of the pattern toward interfering signal sources. The technique was conceived for use in a Global Positioning System (GPS) receiver, for which the desired signal sources would be GPS satellites and typical interference sources would be terrestrial objects that cause multipath propagation. The technique could also be used to optimize reception in spread-spectrum cellular-telephone and military communication systems. During reception of radio signals in a conventional phased-array antenna system, received signals at their original carrier frequencies are phase-shifted, then combined by analog circuitry. The combination signal is then subjected to down-conversion and demodulation. In a system according to the proposed technique (see figure), the signal received by each antenna would be subjected to down-conversion, spread-spectrum demodulation, and correlation; this processing would be performed separately from, and simultaneously with, similar processing of signals received by the other antenna elements. Following analog down-conversion to baseband, the signals would be digitized, and all subsequent processing would be digital. In the digital process, residual carriers would be removed and each signal would be correlated with a locally generated model pseudorandum-noise code, all following normal GPS procedure. As part of this procedure, accumulated values would be added in software and the resulting signals would be phase-shifted in software by the amounts necessary to synthesize the desired antenna directional gain pattern of peaks and nulls. The principal advantage of this technique over the conventional radio-frequency-combining technique is that the parallel digital baseband processing of the signals from the various antenna elements would be a relatively inexpensive and flexible means for exploiting the inherent multiple-peak/multiple-null aiming capability of a phased-array antenna. In the original intended GPS application, the peaks and nulls could be directed independently for each GPS signal being tracked by the GPS receiver. The technique could also be applied to other code-division multiple-access communication systems.

Dunn, Charles E.↗

NASA NTRS2013

Intraseasonal and Interannual Variability of the Quasi-Two Day Wave in the Northern Hemisphere Summer Mesosphere

This study uses global synoptic meteorological fields from a high-altitude data assimilation system to investigate the spatial and temporal characteristics of the quasi-2 day wave (Q2DW) and migrating diurnal tide during the Northern Hemisphere summers of 2007, 2008, and 2009. By applying a 2-dimensional fast Fourier transform to meridional wind and temperature fields, we are able to identify Q2DW source regions and to diagnose propagation of Q2DW activity into the upper mesosphere and lower thermosphere. We find that Q2DW is comprised primarily of westward propagating zonal wavenumber 3 and wavenumber 4 components that originate from within baroclinically unstable regions along the equatorward flank of the summer midlatitude easterly jet. Amplitude variations of wavenumbers 3 and 4 tend to be anti-correlated throughout the summer, with wavenumber 3 maximizing in July and wavenumber 4 maximizing in late June and early August. Monthly mean Q2DW amplitudes between 30 50N latitude are largest when diurnal tidal amplitudes are smallest and vice versa. However, there is no evidence of any rapid amplification of the Q2DW via nonlinear interaction with the diurnal tide. Instead, variations of Q2DW amplitudes during July are closely linked to variations in the strength and location of the easterly jet core from one summer to the next, with a stronger jet producing larger Q2DW amplitudes. Linear instability model calculations based on the assimilated wind fields find fast growing zonal wavenumber 3 and 4 modes with periods near 2 days in the vicinity of the easterly jet.

Two day wave↗

NASA NTRS2017

Reconnection-Driven Coronal-Hole Jets with Gravity and Solar Wind

Coronal-hole jets occur ubiquitously in the Sun's coronal holes, at EUV and X-ray bright points associated with intrusions of minority magnetic polarity. The embedded-bipole model for these jets posits that they are driven by explosive, fast reconnection between the stressed closed field of the embedded bipole and the open field of the surrounding coronal hole. Previous numerical studies in Cartesian geometry, assuming uniform ambient magnetic field and plasma while neglecting gravity and solar wind, demonstrated that the model is robust and can produce jet-like events in simple configurations. We have extended these investigations by including spherical geometry,gravity, and solar wind in a nonuniform, coronal hole-like ambient atmosphere. Our simulations confirm that the jet is initiated by the onset of a kink-like instability of the internal closed field, which induces a burst of reconnection between the closed and external open field, launching a helical jet. Our new results demonstrate that the jet propagation is sustained through the outer corona, in the form of a traveling nonlinear Alfven wave front trailed by slower-moving plasma density enhancements that are compressed and accelerated by the wave. This finding agrees well with observations of white-light coronal-hole jets, and can explain microstreams and torsional Alfven waves detected in situ in the solar wind. We also use our numerical results to deduce scaling relationships between properties of the coronal source region and the characteristics of the resulting jet, which can be tested against observations.

Karpen, J. T.↗

NASA NTRS2014

An Experimental Study of Unconfined Hydrogen/Oxygen and Hydrogen/Air Explosions

Development tests are being conducted to characterize unconfined Hydrogen/air and Hydrogen/Oxygen blast characteristics. Most of the existing experiments for these types of explosions address contained explosions, like shock tubes. Therefore, the Hydrogen Unconfined Combustion Test Apparatus (HUCTA) has been developed as a gaseous combustion test device for determining the relationship between overpressure, impulse, and flame speed at various mixture ratios for unconfined reactions of hydrogen/oxygen and hydrogen/air. The system consists of a central platform plumbed to inject and mix component gasses into an attached translucent bag or balloon while monitoring hydrogen concentration. All tests are ignited with a spark with plans to introduce higher energy ignition sources in the future. Surrounding the platform are 9 blast pressure "Pencil" probes. Two high-speed cameras are used to observe flame speed within the combustion zone. The entire system is raised approx. 6 feet off the ground to remove any ground reflection from the measurements. As of this writing greater than 175 tests have been performed and include Design of Experiments test sets. Many of these early tests have used bags or balloons between approx. 340L and approx. 1850L to quantify the effect of gaseous mixture ratio on the properties of interest. All data acquisition is synchronized between the high-speed cameras, the probes, and the ignition system to observe flame and shock propagation. Successful attempts have been made to couple the pressure profile with the progress of the flame front within the combustion zone by placing a probe within the bag. Overpressure and impulse data obtained from these tests are used to anchor engineering analysis tools, CFD models and in the development of blast and fragment acceleration models.

Richardson, Erin↗

NASA NTRS2012

Orion Absolute Navigation System Progress and Challenge

The absolute navigation design of NASA's Orion vehicle is described. It has undergone several iterations and modifications since its inception, and continues as a work-in-progress. This paper seeks to benchmark the current state of the design and some of the rationale and analysis behind it. There are specific challenges to address when preparing a timely and effective design for the Exploration Flight Test (EFT-1), while still looking ahead and providing software extensibility for future exploration missions. The primary onboard measurements in a Near-Earth or Mid-Earth environment consist of GPS pseudo-range and delta-range, but for future explorations missions the use of star-tracker and optical navigation sources need to be considered. Discussions are presented for state size and composition, processing techniques, and consider states. A presentation is given for the processing technique using the computationally stable and robust UDU formulation with an Agee-Turner Rank-One update. This allows for computational savings when dealing with many parameters which are modeled as slowly varying Gauss-Markov processes. Preliminary analysis shows up to a 50% reduction in computation versus a more traditional formulation. Several state elements are discussed and evaluated, including position, velocity, attitude, clock bias/drift, and GPS measurement biases in addition to bias, scale factor, misalignment, and non-orthogonalities of the accelerometers and gyroscopes. Another consideration is the initialization of the EKF in various scenarios. Scenarios such as single-event upset, ground command, and cold start are discussed as are strategies for whole and partial state updates as well as covariance considerations. Strategies are given for dealing with latent measurements and high-rate propagation using multi-rate architecture. The details of the rate groups and the data ow between the elements is discussed and evaluated.

Holt, Greg N.↗

DOE OSTI2024

Time-resolved quantification of key species and mechanistic insights in low-temperature tetrahydrofuran oxidation

Here, we investigate the kinetics and report the time-resolved concentrations of key chemical species in the oxidation of tetrahydrofuran (THF) at 7500 torr and 450–675 K. Experiments are carried out using high-pressure multiplexed photoionization mass spectrometry (MPIMS) combined with tunable vacuum ultraviolet radiation from the Berkely Lab Advanced Light Source. Intermediates and products are quantified using reference photoionization (PI) cross sections, when available, and constrained by a global carbon balance tracking approach at all experimental temperatures simultaneously for the species without reference cross sections. From carbon balancing, we determine time-resolved concentrations for the ROO˙ and ˙OOQOOH radical intermediates, butanedial, and the combined concentration of ketohydroperoxide (KHP) and unsaturated hydroperoxide (UHP) products stemming from the ˙QOOH + O 2 reaction. Furthermore, we quantify a product that we tentatively assign as fumaraldehyde, which arises from UHP decomposition via H 2 O or ˙OH + H loss. The experimentally derived species concentrations are compared with model predictions using the most recent literature THF oxidation mechanism of Fenard et al., (Combust. Flame, 2018, 191, 252–269). Our results indicate that the literature mechanism significantly overestimates THF consumption and the UHP + KHP concentration at our conditions. The model predictions are sensitive to the rate coefficient for the ROO˙ isomerization to ˙QOOH, which is the gateway for radical chain propagating and branching pathways. Comparisons with our recent results for cyclopentane (Demireva et al., Combust. Flame, 2023, 257, 112506) provide insights into the effect of the ether group on reactivity and highlight the need to determine accurate rate coefficients of ROO˙ isomerization and subsequent reactions.

Demireva, Maria↗

DOE OSTI2023

A reduced-model (nSOLT) simulation of neutral recycling effects on plasma turbulence in the divertor region of MAST-U

The 2D scrape-off-layer turbulence code (nSOLT), which includes 1D kinetic neutral–plasma interactions, is applied to study effects of neutral recycling on plasma turbulence for parameters illustrative of the MAST-U divertor region. Neutral recycling is modeled by injecting a fraction of the parallel plasma flux to the divertor back into the simulation domain as a source of Franck–Condon-distributed neutrals. Stationary sources, concentrated at the magnetic separatrix, model plasma streaming into the divertor region from the upstream scrape-off-layer and sustain plasma turbulence absent neutral recycling. Starting from one such no-neutrals equilibrium, we initiate recycling in a numerical experiment designed to diagnose and identify the effects of various neutral–plasma interactions on the divertor plasma, divertor turbulence, and plasma exhaust. The onset of recycling triggers an initial burst of enhanced cross field plasma transport that is quelled by ionization cooling and charge–exchange (CX) friction, with growing neutral pressure, leading to a quiescent, turbulence-free state. Diagnosis of this transient burst reveals that (1) the sudden increase in plasma density due to ionization dominates the onset of the burst, (2) electron cooling due to ionization increases collisionality and disconnects blob filaments from the sheath, and (3) CX friction drives tripole polarization of a blob that can dominate the curvature-driven dipole polarization, leading to the stagnation of blob propagation and reduced radial turbulent transport. It is shown that CX friction is negligible compared to sheath physics in determining equilibrium mean flow shearing rates, for parameters considered herein (specifically a short connection length to the divertor target), while it can significantly reduce interchange-instability growth rates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1992

Response of a stably stratified atmosphere to low-level heating - An application to the heat island problem

Two-dimensional airflow characteristics past a heat island are investigated using both a linear analytic model and a nonlinear numerical model in the context of the response of a stably stratified atmosphere to specified low-level heating in a constant shear flow. Results from the steady-state, linear, analytic solutions exhibit typical flow response fields that gravity waves produce in response to the local heat source in the presence of environmental flow. The magnitude of the perturbation vertical velocity is shown to be much larger in the shear-flow case than in the uniform-flow case. Two distinct flow features are observed for larger heating amplitude (hence, larger nonlinearity factor): the gravity-wave-type response field on the upstream side of the heat island and the strong updraft circulation cell located on the downstream side. As the heating amplitude increases, the updraft circulation cell strengthens and shifts farther downwind. The strong updraft cell is believed to be partly responsible for precipitation enhancement observed on the downstream side of the heat island. It is found that the continuing downwind propagation of the updraft circulation cell is related to basic-state wind speed.

Baik, Jong-Jin↗

NASA NTRS2011

Orion Absolute Navigation System Progress and Challenges

The Orion spacecraft is being designed as NASA's next-generation exploration vehicle for crewed missions beyond Low-Earth Orbit. The navigation system for the Orion spacecraft is being designed in a Multi-Organizational Design Environment (MODE) team including contractor and NASA personnel. The system uses an Extended Kalman Filter to process measurements and determine the state. The design of the navigation system has undergone several iterations and modifications since its inception, and continues as a work-in-progress. This paper seeks to benchmark the current state of the design and some of the rationale and analysis behind it. There are specific challenges to address when preparing a timely and effective design for the Exploration Flight Test (EFT-1), while still looking ahead and providing software extensibility for future exploration missions. The primary measurements in a Near-Earth or Mid-Earth environment consist of GPS pseudorange and deltarange, but for future explorations missions the use of star-tracker and optical navigation sources need to be considered. Discussions are presented for state size and composition, processing techniques, and consider states. A presentation is given for the processing technique using the computationally stable and robust UDU formulation with an Agee-Turner Rank-One update. This allows for computational savings when dealing with many parameters which are modeled as slowly varying Gauss-Markov processes. Preliminary analysis shows up to a 50% reduction in computation versus a more traditional formulation. Several state elements are discussed and evaluated, including position, velocity, attitude, clock bias/drift, and GPS measurement biases in addition to bias, scale factor, misalignment, and non-orthogonalities of the accelerometers and gyroscopes. Another consideration is the initialization of the EKF in various scenarios. Scenarios such as single-event upset, ground command, pad alignment, cold start are discussed as are strategies for whole and partial state updates as well as covariance considerations. Strategies are given for dealing with latent measurements and high-rate propagation using multi-rate architecture. The details of the rate groups and the data ow between the elements is discussed and evaluated.

Holt, Greg N.↗