Results for “Solar Technology Center” — Page 52

NASA NTRS2016

Launch Pad in a Box

NASA Kennedy Space Center (KSC) is developing a new deployable launch system capability to support a small class of launch vehicles for NASA and commercial space companies to test and launch their vehicles. The deployable launch pad concept was first demonstrated on a smaller scale at KSC in 2012 in support of NASA Johnson Space Center's Morpheus Lander Project. The main objective of the Morpheus Project was to test a prototype planetary lander as a vertical takeoff and landing test-bed for advanced spacecraft technologies using a hazard field that KSC had constructed at the Shuttle Landing Facility (SLF). A steel pad for launch or landing was constructed using a modular design that allowed it to be reconfigurable and expandable. A steel flame trench was designed as an optional module that could be easily inserted in place of any modular steel plate component. The concept of a transportable modular launch and landing pad may also be applicable to planetary surfaces where the effects of rocket exhaust plume on surface regolith is problematic for hardware on the surface that may either be damaged by direct impact of high speed dust particles, or impaired by the accumulation of dust (e.g., solar array panels and thermal radiators). During the Morpheus free flight campaign in 2013-14, KSC performed two studies related to rocket plume effects. One study compared four different thermal ablatives that were applied to the interior of a steel flame trench that KSC had designed and built. The second study monitored the erosion of a concrete landing pad following each landing of the Morpheus vehicle on the same pad located in the hazard field. All surfaces of a portable flame trench that could be directly exposed to hot gas during launch of the Morpheus vehicle were coated with four types of ablatives. All ablative products had been tested by NASA KSC and/or the manufacturer. The ablative thicknesses were measured periodically following the twelve Morpheus free flight tests. The thermal energy from the Morpheus rocket exhaust plume was only found to be sufficient to cause appreciable ablation of one of the four ablatives that were tested. The rocket exhaust plume did cause spalling of concrete during each descent and landing on a landing pad in the hazard field. The Extended Abstract ASE Earth and Space Conference April, 2016 - Orlando, FL concrete surface was laser scanned following each Morpheus landing, and the total volume of spalled concrete that eroded between the first and final landings of the Morpheus Project's test campaign was estimated. This paper will also describe a new deployable launch system (DLS) capability that is being developed at KSC and was publicly announced in May 2015 (KSC Partnerships, 2015). The DLS is a set of multi-user Ground Support Equipment that will be used to test and launch small class launch vehicles. The system is comprised of four main elements: the Launch Stand, the Flame Deflector, the Pad Apron and the KAMAG transporter. The system elements are designed to be deployed at launch or test sites within the KSC/CCAFS boundaries. The DLS is intended to be used together with the Fluid and Electrical System of the Universal Propellant Servicing Systems and Mobile Power Data and Communications Unit.

Ablatives Testing↗

NASA NTRS2016

Launch Pad in a Box

NASA Kennedy Space Center (KSC) is developing a new deployable launch system capability to support a small class of launch vehicles for NASA and commercial space companies to test and launch their vehicles. The deployable launch pad concept was first demonstrated on a smaller scale at KSC in 2012 in support of NASA Johnson Space Center's Morpheus Lander Project. The main objective of the Morpheus Project was to test a prototype planetary lander as a vertical takeoff and landing test-bed for advanced spacecraft technologies using a hazard field that KSC had constructed at the Shuttle Landing Facility (SLF). A steel pad for launch or landing was constructed using a modular design that allowed it to be reconfigurable and expandable. A steel flame trench was designed as an optional module that could be easily inserted in place of any modular steel plate component. The concept of a transportable modular launch and landing pad may also be applicable to planetary surfaces where the effects of rocket exhaust plume on surface regolith is problematic for hardware on the surface that may either be damaged by direct impact of high speed dust particles, or impaired by the accumulation of dust (e.g., solar array panels and thermal radiators). During the Morpheus free flight campaign in 2013-14, KSC performed two studies related to rocket plume effects. One study compared four different thermal ablatives that were applied to the interior of a steel flame trench that KSC had designed and built. The second study monitored the erosion of a concrete landing pad following each landing of the Morpheus vehicle on the same pad located in the hazard field. All surfaces of a portable flame trench that could be directly exposed to hot gas during launch of the Morpheus vehicle were coated with four types of ablatives. All ablative products had been tested by NASA KSC and/or the manufacturer. The ablative thicknesses were measured periodically following the twelve Morpheus free flight tests. The thermal energy from the Morpheus rocket exhaust plume was only found to be sufficient to cause appreciable ablation of one of the four ablatives that were tested. The rocket exhaust plume did cause spalling of concrete during each descent and landing on a landing pad in the hazard field. The Extended Abstract ASE Earth and Space Conference April, 2016 - Orlando, FL concrete surface was laser scanned following each Morpheus landing, and the total volume of spalled concrete that eroded between the first and final landings of the Morpheus Project's test campaign was estimated. This paper will also describe a new deployable launch system (DLS) capability that is being developed at KSC and was publicly announced in May 2015 (KSC Partnerships, 2015). The DLS is a set of multi-user Ground Support Equipment that will be used to test and launch small class launch vehicles. The system is comprised of four main elements: the Launch Stand, the Flame Deflector, the Pad Apron and the KAMAG transporter. The system elements are designed to be deployed at launch or test sites within the KSC/CCAFS boundaries. The DLS is intended to be used together with the Fluid and Electrical System of the Universal Propellant Servicing Systems and Mobile Power Data and Communications Unit

Mobile Launch Pad Development↗

NASA NTRS2019

NASA Proof-of-Concept 1-W Stirling Convertor Development for Small RPS

Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future small spacecraft with electrical power by converting heat from one or more Light Weight Radioisotope Heater Units (LWRHU). An initial design converts multiple watts of heat to one watt of electrical power output using a Stirling convertor. A variety of mission concepts have been studied by NASA and the U. S. Department of Energy (DOE) that would utilize low power Radioisotope Power Systems (RPS) for probes, landers, rovers, and repeaters. These missions would contain science instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data such as, radiation, temperature, pressure, seismic activity, and other surface measurements for planetary science and to inform future mission planners. The studies propose using fractional versions of the General Purpose Heat Source (GPHS) or multiple LWRHUs to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Efforts to develop the concept have focused on maturation of a 1-We convertor and controller design and performance evaluation of an evacuated metal foil insulation. A proof-of-concept 1-We convertor, controller, and evacuated metal foil insulation package have been fabricated and are undergoing characterization testing. The current status, findings, and path forward for the effort are explained in this paper.

Schifer, Nicholas A.↗

DOE OSTI2017

Performance Evaluation of a Thermal Load Reduction System in a Hyundai Sonata PHEV

Increased adoption of electric-drive vehicles (EDVs) requires overcoming hurdles including limited vehicle range. Vehicle cabin heating and cooling demand for occupant climate control requires energy from the main battery and has been shown to significantly degrade vehicle range. During peak cooling and heating conditions, climate control can require as much or more energy as propulsion. As part of an ongoing project, NREL and project partners Hyundai America Technical Center, Inc. (HATCI), Gentherm , Pittsburgh Glass Works (PGW), PPG Industries, Sekisui, 3M, and Hanon Systems developed a thermal load reduction system in order to reduce the range penalty associated with electric vehicle climate control. Solar reflective paint, solar control glass, heated and cooled/ventilated seats, heated surfaces, and heated windshield with door demisters were integrated into a Hyundai Sonata plug-in hybrid electric vehicle (PHEV). Cold weather field-testing was conducted in Fairbanks, Alaska while warm weather testing was conducted in Death Valley, California to assess the system performance in comparison to the baseline production vehicle. In addition, environmental chamber testing at peak heating and cooling conditions was performed to assess the performance of the system in standardized conditions compared to the baseline. Experimental results are presented in this paper providing quantitative data to automobile manufacturers on the impact of climate control thermal load reduction technologies to increase the advanced thermal technology adoption and market penetration of electric drive vehicles.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS2005

Micro-Inspector Spacecraft for Space Exploration Missions

NASA is seeking to embark on a new set of human and robotic exploration missions back to the Moon, to Mars, and destinations beyond. Key strategic technical challenges will need to be addressed to realize this new vision for space exploration, including improvements in safety and reliability to improve robustness of space operations. Under sponsorship by NASA's Exploration Systems Mission, the Jet Propulsion Laboratory (JPL), together with its partners in government (NASA Johnson Space Center) and industry (Boeing, Vacco Industries, Ashwin-Ushas Inc.) is developing an ultra-low mass (<3.0 kg) free-flying micro-inspector spacecraft in an effort to enhance safety and reduce risk in future human and exploration missions. The micro-inspector will provide remote vehicle inspections to ensure safety and reliability, or to provide monitoring of in-space assembly. The micro-inspector spacecraft represents an inherently modular system addition that can improve safety and support multiple host vehicles in multiple applications. On human missions, it may help extend the reach of human explorers, decreasing human EVA time to reduce mission cost and risk. The micro-inspector development is the continuation of an effort begun under NASA's Office of Aerospace Technology Enabling Concepts and Technology (ECT) program. The micro-inspector uses miniaturized celestial sensors; relies on a combination of solar power and batteries (allowing for unlimited operation in the sun and up to 4 hours in the shade); utilizes a low-pressure, low-leakage liquid butane propellant system for added safety; and includes multi-functional structure for high system-level integration and miniaturization. Versions of this system to be designed and developed under the H&RT program will include additional capabilities for on-board, vision-based navigation, spacecraft inspection, and collision avoidance, and will be demonstrated in a ground-based, space-related environment. These features make the micro-inspector design unique in its ability to serve crewed as well as robotic spacecraft, well beyond Earth-orbit and into arenas such as robotic missions, where human teleoperation capability is not locally available.

microspacecraft↗

NASA NTRS2012

Model Development and Experimental Validation of the Fusible Heat Sink Design for Exploration Vehicles

The Fusible Heat Sink is a novel vehicle heat rejection technology which combines a flow through radiator with a phase change material. The combined technologies create a multi-function device able to shield crew members against Solar Particle Events (SPE), reduce radiator extent by permitting sizing to the average vehicle heat load rather than to the peak vehicle heat load, and to substantially absorb heat load excursions from the average while constantly maintaining thermal control system setpoints. This multi-function technology provides great flexibility for mission planning, making it possible to operate a vehicle in hot or cold environments and under high or low heat load conditions for extended periods of time. This paper describes the model development and experimental validation of the Fusible Heat Sink technology. The model developed was intended to meet the radiation and heat rejection requirements of a nominal MMSEV mission. Development parameters and results, including sizing and model performance will be discussed. From this flight-sized model, a scaled test-article design was modeled, designed, and fabricated for experimental validation of the technology at Johnson Space Center thermal vacuum chamber facilities. Testing showed performance comparable to the model at nominal loads and the capability to maintain heat loads substantially greater than nominal for extended periods of time.

Cognata, Thomas J.↗

NASA NTRSDate not supplied

Wearable Protective Technologies

We are currently creating protective garments to be worn during the duration of SPE (solar particle events). Several garment prototypes have been created to protect the body, but nothing has been created for head protection. My focus during this internship was creating headgear designs. Some of the big requirements of an effective headgear design is that the hood design needs to cover the forehead and not have any gaps between the hood and neckline, and the areal density of radiation shielding needs to be at least 1.5 g/cm2. My designs were inspired by many different brands and designers including Nike’s outerwear selection, Moncler’s Fall 20 Genius collaborations with Simone Rocha, Craig Green, and Alyx, Marine Serre F/W 20, and A-Cold-Wall S/S 19. All of these had great examples of hood and vest designs. Many sketches were created from these and many other inspirations. Pattern development began by taking several measurements of the head and neck. I drafted the hood to cover the forehead and cover the neck. After the initial draft, the pattern was modified to accommodate a center panel to contour and shape the hood further. I also created a shoulder drape based on a kimono sleeve to add extra coverage over the neckline of the garment from a basic sloper’s neckline and shoulders. Radiation shielding was a special consideration in my design work. I did extensive research on different materials and ways to incorporate them into garments and found that I was not limited to polypropylene or polyethylene. Many common textiles are hydrogen rich, such as cotton, polyester, and silk, and could be incorporated into designs as radiation shielding. From this research, I am in the process of creating a prototype that uses these materials as shielding. I will be returning for the summer and hope to put more of the ideas I have into production.

Nicole Dugan↗

DOE OSTI2018

Ultrafast Electron Trapping and Defect-Mediated Recombination in NiO Probed by Femtosecond Extreme Ultraviolet Reflection–Absorption Spectroscopy

Understanding the chemical nature of defect sites as well as the mechanism of defect-mediated recombination is critical for the rational design of energy conversion materials with improved efficiency. Using femtosecond extreme ultraviolet (XUV) spectroscopy in conjunction with X-ray photoelectron spectroscopy (XPS), we present results on the ultrafast electron dynamics in NiO prepared with varying concentrations of defect states. We find that oxygen vacancy defects do not serve as the primary recombination center, but rather the recombination rate scales linearly with the density of Ni metal defects. This suggests that grain boundaries between Ni metal and NiO are responsible for fast carrier recombination in partially reduced NiO. Here, our kinetic model shows that the photoexcited electrons self-trap via small polaron formation on the subpicosecond time scale. Additionally, we estimate an absolute measurement of small polaron formation rates, direct versus defect-mediated recombination rates, and the small polaron diffusion coefficient in NiO. This study provides important parameters for engineering NiO based materials for solar energy harvesting applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2011

Offshore Renewable Energy R&D (Fact Sheet)

This fact sheet describes the offshore renewable energy R&D efforts at NREL's NWTC. As the United States increases its efforts to tap the domestic energy sources needed to diversify its energy portfolio and secure its energy supply, more attention is being focused on the rich renewable resources located offshore. Offshore renewable energy sources include offshore wind, waves, tidal currents, ocean and river currents, and ocean thermal gradients. According to a report published by the National Renewable Energy Laboratory (NREL) in 2010,1 U.S. offshore wind resources have a gross potential generating capacity four times greater than the nation's present electric capacity, and the Electric Power Research Institute estimates that the nation's ocean energy resources could ultimately supply at least 10% of its electric supply. For more than 30 years, NREL has advanced the science of renewable energy while building the capabilities to guide rapid deployment of commercial applications. Since 1993, NREL's National Wind Technology Center (NWTC) has been the nation's premier wind energy research facility, specializing in the advancement of wind technologies that range in size from a kilowatt to several megawatts. For more than 8 years, the NWTC has been an international leader in the field of offshore floating wind system analysis. Today, researchers at the NWTC are taking their decades of experience and extensive capabilities and applying them to help industry develop cost-effective hydrokinetic systems that convert the kinetic energy in water to provide power for our nation's heavily populated coastal regions. The center's capabilities and experience cover a wide spectrum of wind and water energy engineering disciplines, including atmospheric and ocean fluid mechanics, aerodynamics; aeroacoustics, hydrodynamics, structural dynamics, control systems, electrical systems, and testing.

14 SOLAR ENERGY↗

NASA NTRS2005

MIT-NASA Workshop: Transformational Technologies

As a space faring nation, we are at a critical juncture in the evolution of space exploration. NASA has announced its Vision for Space Exploration, a vision of returning humans to the Moon, sending robots and eventually humans to Mars, and exploring the outer solar system via automated spacecraft. However, mission concepts have become increasingly complex, with the potential to yield a wealth of scientific knowledge. Meanwhile, there are significant resource challenges to be met. Launch costs remain a barrier to routine space flight; the ever-changing fiscal and political environments can wreak havoc on mission planning; and technologies are constantly improving, and systems that were state of the art when a program began can quickly become outmoded before a mission is even launched. This Conference Publication describes the workshop and featured presentations by world-class experts presenting leading-edge technologies and applications in the areas of power and propulsion; communications; automation, robotics, computing, and intelligent systems; and transformational techniques for space activities. Workshops such as this one provide an excellent medium for capturing the broadest possible array of insights and expertise, learning from researchers in universities, national laboratories, NASA field Centers, and industry to help better our future in space.

Mankins, J. C.↗

NASA NTRS2008

The Solar Dynamics Observatory: Your Eye On The Sun

The Sun hiccups and satellites die. That is what NASA's Living With a Star Program is all about. The Solar Dynamics Observatory (SDO) is the first Space Weather Mission in LWS. SDO's main goal is to understand, driving towards a predictive capability, those solar variations that influence life on Earth and humanity's technological systems. The past decade has seen an increasing emphasis on understanding the entire Sun, from the nuclear reactions at the core to the development and loss of magnetic loops in the corona. SDO's three science investigations (HMI, AIA, and EVE) will determine how the Sun's magnetic field is generated and structured, how this stored magnetic energy is released into the heliosphere and geospace as the solar wind, energetic particles, and variations in the solar irradiance. SDO will return full-disk Dopplergrams, full-disk vector magnetograms, full-disk images at nine E/UV wavelengths, and EUV spectral irradiances, all taken at a rapid cadence. This means you can "observe the database" to study events, but we can also move forward in producing quantitative models of what the Sun is doing today. SDO is scheduled to launch in 2008 on an Atlas V rocket from the Kennedy Space Center, Cape Canaveral, Florida. The satellite will fly in a 28 degree inclined geosynchronous orbit about the longitude of New Mexico, where a dedicated Ka-band ground station will receive the 150 Mbps data flow. How SDO data will transform the study of the Sun and its affect on Space Weather studies will be discussed.

Pesnell, William Dean↗

NASA NTRS2008

The Solar Dynamics Observatory

The Solar Dynamics Observatory (SDO) is the first Space Weather Mission in NASA's Living With a Star Program. SDO's main goal is to understand, driving towards a predictive capability, those solar variations that influence life on Earth and humanity's technological systems. The past decade has seen an increasing emphasis on understanding the entire Sun, from the nuclear reactions at the core to the development and loss of magnetic loops in the corona. SDO's three science investigations (HMI, AIA, and EVE) will determine how the Sun's magnetic field is generated and structured, how this stored magnetic energy is released into the heliosphere and geospace as the solar wind, energetic particles, and variations in the solar irradiance. SDO will return full-disk Dopplergrams, full-disk vector magnetograms, full-disk images at nine EIUV wavelengths, and EUV spectral irradiances, all taken at a rapid cadence. This means you can 'observe the database' to study events, but we can also move forward in producing quantitative models of what the Sun is doing today. SDO is scheduled to launch in 2008 on an Atlas V rocket from the Kennedy Space Center, Cape Canaveral, Florida. The satellite will fly in a 28 degree inclined geosynchronous orbit about the longitude of New Mexico, where a dedicated Ka-band ground station will receive the 150 Mbps data flow. How SDO data will transform the study of the Sun and its affect on Space Weather studies will be discussed.

Pesnell, William D.↗

DOE OSTI2012

Quantum simulator of an open quantum system using superconducting qubits: exciton transport in photosynthetic complexes

Open quantum system approaches are widely used in the description of physical, chemical and biological systems. A famous example is electronic excitation transfer in the initial stage of photosynthesis, where harvested energy is transferred with remarkably high efficiency to a reaction center. This transport is affected by the motion of a structured vibrational environment, which makes simulations on a classical computer very demanding. Here we propose an analog quantum simulator of complex open system dynamics with a precisely engineered quantum environment. Our setup is based on superconducting circuits, a well established technology. As an example, we demonstrate that it is feasible to simulate exciton transport in the Fenna–Matthews–Olson photosynthetic complex. Our approach allows for a controllable single-molecule simulation and the investigation of energy transfer pathways as well as non-Markovian noise-correlation effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRSDate not supplied

Solar Polar Imager Concept

During late 2019 and early 2020, the Advanced Concepts Office design team at NASA’s George C. Marshall Space Flight Center (MSFC) completed a concept study for a Solar Polar Imager (SPI) mission. The goal of the study was to perform a preliminary design of the spacecraft bus containing a minimum set of science instruments and supporting subsystems. The science goal of the SPI mission is to better understand the Sun and the heliosphere by observing the Sun from a high heliographic latitude. A highly inclined orbit (of 75°) allows helioseismology observations from a high latitude, providing measurements in the high latitude regions for the first time. The orbit also allows measurements of the photospheric magnetic fields in the polar regions, as well as direct measurements of the heliospheric magnetic field and solar wind. The high latitude gives the spacecraft a unique top-down view of coronal mass ejections (CMEs) that could affect space weather around Earth and allow the velocity and directions of these CMEs to be better quantified. Solar sail technology is chosen as the propulsion option necessary to deliver the spacecraft to a heliocentric circular orbit at 0.48 AU and an inclination of 75°. The sail area is restricted to 7000 m2, the maximum size that can be developed in the near term. The sail is also assumed to rotate at 1 rpm to avoid buckling of the supporting booms. The total launch mass is 349 kg, which consists of 233 kg for the SPI Bus, 52 kg for the solar sail and deployment mechanisms, and 64 kg for the Spin-up Bus/launch vehicle payload adapter. Dropping the Spin-up Bus after sail deployment, the characteristic acceleration of the sail is about 0.22 mm/s2. The resulting total mission time is just over 13 years, which includes a 3-year duration at the 75° inclination.

Dan Thomas↗

NASA NTRSDate not supplied

Solar Polar Imager Concept

During late 2019 and early 2020, the Advanced Concepts Office design team at NASA’s George C. Marshall Space Flight Center (MSFC) completed a concept study for a Solar Polar Imager (SPI) mission. The goal of the study was to perform a preliminary design of the spacecraft bus containing a minimum set of science instruments and supporting subsystems. The science goal of the SPI mission is to better understand the Sun and the heliosphere by observing the Sun from a high heliographic latitude. A highly inclined orbit (of 75°) allows helioseismology observations from a high latitude, providing measurements in the high latitude regions for the first time. The orbit also allows measurements of the photospheric magnetic fields in the polar regions, as well as direct measurements of the heliospheric magnetic field and solar wind. The high latitude gives the spacecraft a unique top-down view of coronal mass ejections (CMEs) that could affect space weather around Earth and allow the velocity and directions of these CMEs to be better quantified. Solar sail technology is chosen as the propulsion option necessary to deliver the spacecraft to a heliocentric circular orbit at 0.48 AU and an inclination of 75°. The sail area is restricted to 7000 m2, the maximum size that can be developed in the near term. The sail is also assumed to rotate at 1 rpm to avoid buckling of the supporting booms. The total launch mass is 349 kg, which consists of 233 kg for the SPI Bus, 52 kg for the solar sail and deployment mechanisms, and 64 kg for the Spin-up Bus/launch vehicle payload adapter. Dropping the Spin-up Bus after sail deployment, the characteristic acceleration of the sail is about 0.22 mm/s2. The resulting total mission time is just over 13 years, which includes a 3-year duration at the 75° inclination.

Dan Thomas↗

DOE OSTI2019

Solution for Predictive Physical Modeling in CdTe and Other Thin-Film PV Technologies

The main goal of this work was to eliminate the ambiguity between the observed performance changes under stress and their physical root cause by enabling a depth of modeling that takes account of diffusion and drift at the atomistic level coupled to the electronic subsystem responsible for a PV device’s function. Development of advanced physical models describing capture/emission/ recombination phenomena relevant to multivalent dopants, amphoteric centers, and donor-acceptor pairs was also accomplished. These models, incorporating grain bulk, grain boundaries, and hetero-interface properties, were implemented in a self-contained simulation tool that drastically reduces interpretation ambiguity and, for the first time, allows for predictive design of thin-film PV devices.

14 SOLAR ENERGY↗

DOE OSTI2018

Design of State-of-the-art Flow Cells for Energy Applications

The worldwide energy demand is increasing every day and it necessitates rational and efficient usage of renewable energy. Undoubtedly, utilization of renewable energy can address various environmental challenges. However, all current renewable energy resources (wind, solar, and hydroelectric power) are intermittent and fluctuating in their nature that raises an important question of introducing effective energy storage solutions. Utilization of redox flow cells (RFCs) has recently been recognized as a viable technology for large-scale energy storage and, hence, is well suited for integrating renewable energy and balancing electricity grids. In brief, RFC is an electrochemical storage device where energy is stored in chemical bonds, similar to a battery, but with reactants external to the cell. The state-of-the-art in flow cell technology uses an aqueous acidic electrolyte and simple metal redox couples. Thus, there is an urgent call to develop efficient (high-energy density) and low-cost RFCs to meet the efflorescent energy storage demands. To address the first challenge of achieving high-energy density, we plan to design and further modify complexes composed of bifunctional multidentate ligands and specific metal centers, capable of storing as many electrons as possible. In order to address the second challenge of reducing cost of the RFCs, we plan to use iron (Fe) metal as it regularly occupies multiple oxidation states and is the second most abundant metal in the earth’s crust that makes it an ideal metal for improved energy densities, higher potentials, and numbers of electrons per molecule while maintaining potential cost competitiveness. Density functional theory calculations considering solvation effects will be performed to yield accurate predictions of redox potentials.

25 ENERGY STORAGE↗

DOE OSTI2025

Hierarchical Resilience Planning for Networked Microgrids: A Case Study of Puerto Rico

Microgrids can be designed to enhance the energy resilience of communities and critical infrastructures, such as hospitals, data centers, and communication networks, which are vulnerable to frequent weather-related disruption. Coordinating multiple microgrids in a network can leverage the geographical diversity of load and generation resources while enabling resilient and cost-effective planning of the distribution system. Designing a networked microgrid is complex, involving intricate technical assessment, cost-benefit analysis, site-specific requirements, and the evaluation of existing resources. Therefore, this paper proposes a hierarchical resilience planning framework and performs an extensive techno-economic analysis for the design of a networked microgrid. Hierarchical resilience planning involves technology sizing at an individual community level to meet the critical load and satisfy resilience criteria, and resource optimization at networked microgrid level to provide a higher level of resilience and energy adequacy. A real-world case of Puerto Rico's cooperative microgrid “Microrred de la Montaña” is investigated considering localized electricity tariffs, site-specific demand profiles, solar generation, and existing hydro resources. Multiple optimization scenarios are developed based on the resiliency requirement to estimate the capacity of solar photovoltaic and battery energy storage (BES) to be installed at each substation. The results provide the optimal sizing for individual community and networked microgrid to withstand 1day and 3-day outages along with the criteria for critical load.

13 - HYDRO ENERGY↗